AMSR1.5-7805-NZ

Series AMSR1.5-78-NZ FEATURES: • • • • 3 Pin SIP Package Pin-out compatible with LM78XX Linear Regulators Up to 9.75 Watt | DC-DC Converter • • • • Operating temperature -40°C to +85°C Wide input range Very High Efficiency Up To 95% Continuous Short Circuit Protection Non-Isolated Regulated Output Low ripple and noise Models Single output Model AMSR1.5-782.5-NZ AMSR1.5-783.3-NZ AMSR1.5-7805-NZ AMSR1.5-786.5-NZ Input Voltage (V) 4.75-18 4.75-18 6.5-18 8-18 Output Voltage (V) 2.5 3.3 5 6.5 Output Current max (A) 1.5 1.5 1.5 1.5 Efficiency Vin Min (%) 85 88 91 93 Efficiency Vin Max (%) 88 91 93 95 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity 2 000 000 hrs (MIL-HDBK-217F, Ground Benign, t=+25°C) 1.5 mm from case for 10 sec 300 Free air convection 100 C www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 1 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR1.5-78-NZ Pin Out Specifications Pin 1 2 3 Up to 9.75 Watt | DC-DC Converter Single +Vin GND +Vout Dimensions 2.54 (0.10) Front View 11.50 (0.45 8.90 (0.35) Footprint Ø 1.0 +0.15/-0 (Ø 0.04 + 0.006/-0 17.50 (0.69) Side View 0.50 (0.024) 2.54 (0.10) DIV: 2.54 (0.1) 1 4.10 (0.16) 2 3 0.50 (0.024) 2.54 (0.10) Dimensions are typical values: mm (inch) General Tolerance: ± 0.25 (± 0.01) Pin Tolerance: ± 0.1 (± 0.004) 0.30 (0.012) Bottom View www.aimtec.com F 051e R12.A 2.15 (0.09) 3.21 (0.13) Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR1.5-78-NZ Derating Free Air Convection 71º C Up to 9.75 Watt | DC-DC Converter 100 Output Power (%) 80 60 40 20 0 - 40 - 20 0 20 40 60 80 85 Safe Operating Area 100 Ambient Temperature º C Typical Application Circuits +Vin C1 10uF GND 1 AMSR1.5-78Z 2 3 +Vout C2 22uF GND C1: A low ESR capacitor is required to keep the noise of the converter to a minimum. Ceramic capacitors are recommended with typical value is 10µF / 25V. C2: Installation of C2 is recommended with typical value of 22µF / 16V ceramic for 5V and 6.5V output signal and 22µF / 6.3V ceramic for 2.5V and 3.3V output signal. NOTE: This part is not designed for parallel operation. www.aimtec.com F 051e R12.A Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR1.5-78-NZ Dual Output Connection Up to 9.75 Watt | DC-DC Converter +Vin C1 10uF GND 1 AMSR1.5-78Z 2 3 +Vout C2 22uF GND 1 C1 AMSR1.5-78Z 2 10uF Input Filter 3 C2 22uF -Vout 10uH ~ 47uH 1 C1 10uF GND Output Filter 3 +Vout AMSR1.5-78Z 2 C2 22uF GND C1 10uF 10uH ~ 47uH 1 C1 10uF GND AMSR1.5-78Z 2 3 C1 10uF C1 10uF +Vout C2 22uF GND NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity