ALD1712BSAL

ADVANCED LINEAR DEVICES, INC. ALD1712A/ALD1712B ALD1712 RAIL-TO-RAIL PRECISION OPERATIONAL AMPLIFIER GENERAL DESCRIPTION FEATURES The ALD1712A/ALD1712B/ALD1712 is a monolithic precision operational amplifier intended primarily for a wide range of analog applications in +5V single power supply and ±5V dual power supply systems as well as +5V to +10V battery operated systems. All device characteristics are specified for +5V single supply or ±2.5V dual supply systems. It is manufactured with Advanced Linear Devices' enhanced ACMOS silicon gate CMOS process and is available as a standard cell in ALD's ASIC "Function-Specific" library. • Linear mode operation with input voltages 300mV beyond supply rails • Symmetrical complementary output drive • Output voltages to within 2mV of power supply rails • High load capacitance capability -4000pF typical • No frequency compensation required -unity gain stable • Extremely low input bias currents -0.01pA typical • Dual power supply ±2.5V to ±5.0V • Single power supply +5V to +10V • High voltage gain – typically 85V/mV @ ±2.5V and 250V/mV @ ±5.0V • Drive as low as 1KΩ load with 5mA drive current • Output short circuit protected • Unity gain bandwidth of 1.5MHz • Slew rate of 2.1V/µs • Suitable for rugged, temperature-extreme environments The ALD1712A/ALD1712B/ALD1712 has an input stage that operates to +300mV above and -300mV below the supply voltages with no adverse effects and/or phase reversals. It has been developed specifically with the 5V single supply or ±2.5V dual supply user in mind. Several important characteristics of the device make many applications easy to implement for these supply voltages. First, the operational amplifier can operate with rail-to-rail input and output voltages. This feature allows numerous analog serial stages to be implemented without losing operating voltage margin. Second, the device was designed to accommodate mixed applications where digital and analog circuits may work off the same 5V power supply. Third, the output stage can drive up to 400pF capacitive, and 1KΩ resistive loads in non-inverting unity gain connection, and up to 4000pF at a gain of 5. These features, coupled with extremely low input currents, high voltage gain, useful bandwidth of 1.5MHz, slew rate of 2.1V/µs, low power dissipation, low offset voltage and temperature drift, make the ALD1712A/ALD1712B/ALD1712 a truly versatile, user friendly, operational amplifier. On-chip offset voltage trimming allows the device to be used without nulling in most applications. The device offers typical offset drift of less than 5µV/°C which eliminates many trim or temperature compensation circuits. For precision applications, the ALD1712A/ALD1712B/ALD1712 is designed to settle to 0.01% in 8µs. The unique characteristics at input and output are modeled in an available macromodel. Additionally, robust design and rigorous screening make this device especially suitable for operation in temperature-extreme environments and rugged conditions. ORDERING INFORMATION (“L” suffix denotes lead-free (RoHS)) 0°C to +70°C Operating Temperature Range 0°C to +70°C -55°C to 125°C 8-Pin Small Outline Package (SOIC) 8-Pin Plastic Dip Package 8-Pin CERDIP Package ALD1712ASAL ALD1712BSAL ALD1712SAL ALD1712APAL ALD1712BPAL ALD1712PAL ALD1712ADA ALD1712BDA ALD1712DA * Contact factory for leaded (non-RoHS) or high temperature versions. APPLICATIONS • • • • • • • • • • • • • • Voltage amplifier Voltage follower/buffer Charge integrator Photodiode amplifier Data acquisition systems High performance portable instruments Signal conditioning circuits Sensor and transducer amplifiers Low leakage amplifiers Active filters Sample/Hold amplifier Picoammeter Current to voltage converter Coaxial cable driver PIN CONFIGURATION 8 N/C 7 V+ 3 6 OUT 4 5 N/C N/C 1 -IN 2 +IN V- 2 TOP VIEW SAL, PAL, DA PACKAGES * N/C pins are internally connected. Do not connect externally. Rev 2.1 ©2010 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, CA 94089-1706 Tel: (408) 747-1155 Fax: (408) 747-1286 www.aldinc.com ABSOLUTE MAXIMUM RATINGS Supply voltage, V+ Differential input voltage range Power dissipation Operating temperature range SAL, PAL packages DA package Storage temperature range Lead temperature, 10 seconds CAUTION: ESD Sensitive Device. Use static control procedures in ESD controlled environment. 10.6V -0.3V to V+ +0.3V 600 mW 0°C to +70°C -55°C to +125°C -65°C to +150°C +260°C OPERATING ELECTRICAL CHARACTERISTICS TA = 25°C VS = ±2.5V unless otherwise specified Min 1712A Typ Supply Voltage VS V+ Input Offset Voltage VOS 0.05 0.15 0.35 0.1 0.25 0.55 0.25 Input Offset Current IOS 0.01 10 280 0.01 10 280 Input Bias Current IB 0.01 10 280 0.01 10 280 Input Voltage Range VIR Input Resistance RIN Input Offset Voltage Drift TCVOS Power Supply Rejection Ratio PSRR 65 65 85 85 65 65 85 85 63 63 Common Mode Rejection Ratio CMRR 65 65 83 83 65 65 83 83 Large Signal Voltage Gain AV 50 85 400 50 85 400 -0.3 -2.8 Min ±5.0 10.0 ±2.0 4.0 5.3 +2.8 VO low VO high VO low VO high 4.99 2.35 Max Unit Test Conditions ±5.0 10.0 V V Dual Supply Single Supply 0.5 1.0 mV mV RS ≤ 100KΩ 0°C ≤ TA ≤ +70°C 0.01 10 280 pA pA TA = 25°C 0°C ≤ TA ≤ +70°C 0.01 10 280 pA pA TA = 25°C 0°C ≤ TA ≤ +70°C 5.3 +2.8 V V V+ = +5; notes 2,5 VS = ±2.5V ±5.0 ±2.0 10.0 4.0 -0.3 -2.8 5.3 +2.8 -0.3 -2.8 1013 1013 1013 5 5 5 20 Output Voltage Range Min 1712 Typ Symbol ±2.0 4.0 Max 1712B Typ Max Parameter 20 0.002 0.01 4.998 -2.44 -2.35 2.44 Ω µV/°C RS ≤ 100KΩ 85 85 dB dB RS ≤ 100KΩ 0°C ≤ TA ≤ +70°C 63 63 83 83 dB dB RS ≤ 100KΩ 0°C ≤ TA ≤ +70°C 50 85 400 V/mV V/mV V/mV RL = 10KΩ RL ≥ 1MΩ RL = 10KΩ 0°C ≤ TA ≤ +70°C V V V V RL = 1MΩ V+ = +5V 0°C ≤ TA ≤ +70°C RL = 10KΩ 0°C ≤ TA ≤ +70°C 20 0.002 0.01 0.002 0.01 4.99 4.998 4.99 4.998 -2.44 -2.35 -2.44 -2.35 2.35 2.44 2.35 2.44 8 8 8 mA Output Short Circuit Current ISC Supply Current IS 0.8 1.5 0.8 1.5 0.8 1.5 mA VIN = 0V No Load Power Dissipation PD 4.0 7.5 4.0 7.5 4.0 7.5 mW VS = ±2.5V Input Capacitance CIN 1 Bandwidth BW 1.0 1.5 1.0 1.5 1.0 1.5 MHz Slew Rate SR 1.4 2.1 1.4 2.1 1.4 2.1 V/µs AV = +1 RL = 10KΩ Rise time tr Overshoot Factor ALD1712A/ALD1712B ALD1712 1 1 pF 0.2 0.2 0.2 µs RL = 10KΩ 10 10 10 % RL = 10KΩ CL = 100pF Advanced Linear Devices 2 of 9 OPERATING ELECTRICAL CHARACTERISTICS (cont'd) TA = 25°C VS = ±2.5V unless otherwise specified 1712A Typ Max Min Typ 1712 Symbol Maximum Load Capacitance CL 400 4000 400 4000 400 4000 Input Noise Voltage en 26 26 26 nV/√Hz f =1KHz Input Current Noise in 0.6 0.6 0.6 fA/√Hz f =10Hz ts 8.0 3.0 8.0 3.0 8.0 3.0 µs µs 0.01% 0.1% AV = -1 RL = 5KΩ CL= 50pF Unit Test Conditions Settling Time Min 1712B Parameter Max Min Typ Max Unit Test Conditions pF pF Gain = 1 Gain = 5 TA = 25°C VS = ±5.0V unless otherwise specified Min 1712A Typ Power Supply Rejection Ratio PSRR 83 83 83 dB RS ≤ 100KΩ Common Mode Rejection Ratio CMRR 83 83 83 dB RS ≤ 100KΩ Large Signal Voltage Gain AV 250 250 250 V/mV RL = 10KΩ Output Voltage Range VO low VO high V RL = 10KΩ Bandwidth BW 1.7 1.7 1.7 MHz Slew Rate SR 2.8 2.8 2.8 V/µs -4.90 4.93 Min -4.80 4.80 -4.90 4.93 Max -4.80 Min 1712 Typ Symbol 4.80 Max 1712B Typ Parameter -4.90 4.80 4.93 Max -4.80 AV =+1 CL =50pF VS = ±2.50V -55°C ≤ TA ≤ +125°C unless otherwise specified 1712ADA Typ Max 0.5 1.0 Min 1712DA Symbol Input Offset Voltage VOS Input Offset Current IOS 4.0 Input Bias Current IB 4.0 Power Supply Rejection Ratio PSRR 60 83 60 83 60 83 dB RS ≤ 100KΩ Common Mode Rejection Ratio CMRR 60 83 60 83 60 83 dB RS ≤ 100KΩ Large Signal Voltage Gain AV 10 25 10 25 10 25 V/mV RL = 10KΩ Output Voltage Range VO low VO high 4.8 0.1 4.9 4.8 0.1 4.9 4.8 0.1 4.9 V V RL ≤ 10KΩ RL ≤ 10KΩ ALD1712A/ALD1712B ALD1712 Min 1712BDA Parameter 0.2 Typ Max 0.8 1.5 Min Typ Max Unit Test Conditions 1.2 2.5 mV RS ≤ 100KΩ 4.0 4.0 nA 4.0 4.0 nA 0.2 Advanced Linear Devices 0.2 3 of 9 Design & Operating Notes: 1. The ALD1712A/ALD1712B/ALD1712 CMOS operational amplifier uses a 3 gain stage architecture and an improved frequency compensation scheme to achieve large voltage gain, high output driving capability, and better frequency stability. In a conventional CMOS operational amplifier design, compensation is achieved with a pole splitting capacitor together with a nulling resistor. This method is, however, very bias dependent and thus cannot accommodate the large range of supply voltage operation as is required from a stand alone CMOS operational amplifier. The ALD1712A/ALD1712B/ALD1712 is internally compensated for unity gain stability using a novel scheme that does not use a nulling resistor. This scheme produces a clean single pole roll off in the gain characteristics while providing for more than 70 degrees of phase margin at the unity gain frequency. A unity gain buffer using the ALD1712A/ALD1712B/ALD1712 will typically drive 400pF of external load capacitance without stability problems. In the inverting unity gain configuration, it can drive up to 800pF of load capacitance. Compared to other CMOS operational amplifiers, the ALD1712A/ALD1712B/ ALD1712 has shown itself to be more resistant to parasitic oscillations. 2. The ALD1712A/ALD1712B/ALD1712 has complementary p-channel and n-channel input differential stages connected in parallel to accomplish rail to rail input common mode voltage range. This means that with the ranges of common mode input voltage close to the power supplies, one of the two differential stages is switched off internally. To maintain compatibility with other operational amplifiers, this switching point has been selected to be about 1.5V above the negative supply voltage. Since offset voltage trimming on the ALD1712A/ALD1712B/ALD1712 is made when the input voltage is symmetrical to the supply voltages, this internal switching does not affect a large variety of applications such as an inverting amplifier or non-inverting amplifier with a gain larger than 2.5 (5V operation), where the common mode voltage does not make excursions below this switching point. The user should however, be aware that this switching does take place if the operational amplifier is connected as a unity gain buffer and should make provision in his design to allow for input offset voltage variations. 3. The input bias and offset currents are essentially input protection diode reverse bias leakage currents, and are typically less than 1pA at room temperature. This low input bias current assures that the analog signal from the source will not be distorted by input bias currents. Normally, this extremely high input impedance of greater than 1012Ω would not be a problem as the source impedance would limit the node impedance. However, for applications where source impedance is very high, it may be necessary to limit noise and hum pickup through proper shielding. 4. The output stage consists of class AB complementary output drivers, capable of driving a low resistance load. The output voltage swing is limited by the drain to source on-resistance of the output transistors as determined by the bias circuitry, and the value of the load resistor. When connected in the voltage follower configuration, the oscillation resistant feature, combined with the rail to rail input and output feature, makes an effective analog signal buffer for medium to high source impedance sensors, transducers, and other circuit networks. 5. The ALD1712A/ALD1712B/ALD1712 operational amplifier has been designed to provide full static discharge protection. Internally, the design has been carefully implemented to minimize latch up. However, care must be exercised when handling the device to avoid strong static fields that may degrade a diode junction, causing increased input leakage currents. In using the operational amplifier, the user is advised to power up the circuit before, or simultaneously with, any input voltages applied and to limit input voltages to not exceed 0.3V of the power supply voltage levels. TYPICAL PERFORMANCE CHARACTERISTICS COMMON MODE INPUT VOLTAGE RANGE AS A FUNCTION OF SUPPLY VOLTAGE OPEN LOOP VOLTAGE GAIN AS A FUNCTION OF SUPPLY VOLTAGE AND TEMPERATURE 1000 TA = 25°C OPEN LOOP VOLTAGE GAIN (V/mV) COMMON MODE INPUT VOLTAGE RANGE (V) ±7 ±6 ±5 ±4 ±3 ±2 } +25°C 100 } +125°C 10 RL= 10KΩ RL= 5KΩ ±1 1 0 0 ±1 ±2 ±3 ±4 ±5 ±6 ±7 0 ±2 ±4 ±6 ±8 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) INPUT BIAS CURRENT AS A FUNCTION OF AMBIENT TEMPERATURE SUPPLY CURRENT AS A FUNCTION OF SUPPLY VOLTAGE ±5 1000 VS = ±2.5V 100 SUPPLY CURRENT (mA) INPUT BIAS CURRENT (pA) } -55°C 10 1.0 0.1 INPUTS GROUNDED OUTPUT UNLOADED ±4 ±3 ±2 TA = -55ºC -25°C ±1 +25°C +80°C +125°C 0 0.01 -50 -25 0 25 50 75 100 125 AMBIENT TEMPERATURE (°C) ALD1712A/ALD1712B ALD1712 0 ±1 ±2 ±3 ±4 ±5 ±6 SUPPLY VOLTAGE (V) Advanced Linear Devices 4 of 9 TYPICAL PERFORMANCE CHARACTERISTICS (cont'd) OUTPUT VOLTAGE SWING AS A FUNCTION OF SUPPLY VOLTAGE OPEN LOOP VOLTAGE GAIN AS A FUNCTION OF FREQUENCY 120 ±6 OPEN LOOP VOLTAGE GAIN (db) -55°C ≤ TA ≤ 125°C RL = 10KΩ RL = 10KΩ ±5 ±4 RL = 2KΩ ±3 ±2 100 VS = ±2.5V TA = 25°C 80 60 0 40 45 20 90 0 135 180 -20 0 ±1 ±2 ±3 ±4 ±5 ±6 ±7 1 10 100 SUPPLY VOLTAGE (V) VS = ±2.5V +3 +2 +1 0 -1 -2 -3 -4 INPUT OFFSET VOLTAGE (mV) INPUT OFFSET VOLTAGE (mV) 100K 1M 10M INPUT OFFSET VOLTAGE AS A FUNCTION OF COMMON MODE INPUT VOLTAGE 6 VS = ±2.5V TA = 25°C 4 2 0 -2 -4 -6 -5 -50 -25 0 +25 +50 +75 -2 +100 +125 0 +1 +2 +3 VOLTAGE NOISE DENSITY AS A FUNCTION OF FREQUENCY OPEN LOOP VOLTAGE GAIN AS A FUNCTION OF LOAD RESISTANCE 150 VOLTAGE NOISE DENSITY (nV/ √ Hz) 1000 100 VS = ±2.5V TA = 25°C 10 -1 COMMON MODE INPUT VOLTAGE (V) AMBIENT TEMPERATURE (°C) OPEN LOOP VOLTAGE GAIN (V/mV) 10K FREQUENCY (Hz) INPUT OFFSET VOLTAGE AS A FUNCTION OF AMBIENT TEMPERATURE REPRESENTATIVE UNITS +5 +4 1K PHASE SHIFT IN DEGREES OUTPUT VOLTAGE SWING (V) ±7 1 125 VS = ±2.5V TA = 25°C 100 75 50 25 0 1K 10K 100K 1000K LOAD RESISTANCE (Ω) 10 100 1K 10K 100K 1000K FREQUENCY (Hz) LARGE - SIGNAL TRANSIENT RESPONSE SMALL - SIGNAL TRANSIENT RESPONSE 5V/div 100mV/div VS = ±2.5V TA = 25°C RL = 10KΩ CL = 50pF 1V/div ALD1712A/ALD1712B ALD1712 2µs/div 20mV/div Advanced Linear Devices VS = ±2.5V TA = 25°C RL = 10KΩ CL = 50pF 2µs/div 5 of 9 TYPICAL APPLICATIONS RAIL-TO-RAIL WAVEFORM RAIL-TO-RAIL VOLTAGE FOLLOWER/BUFFER 5V ZIN =~ 1012Ω INPUT 0.1µF +5V 0V VIN +5V OUTPUT 0V OUTPUT CL + RL =10KΩ 400pF 0 ≤ VIN ≤ 5V Performance waveforms. Upper trace is the output of a Wien Bridge Oscillator. Lower trace is the output of Rail-to-Rail voltage follower. * See rail to rail waveform LOW OFFSET SUMMING AMPLIFIER RAIL-TO-RAIL VOLTAGE COMPARATOR +5V 50K +2.5V 10K INPUT 1 .01µF VIN INPUT 2 OUTPUT +5V CL = 4000pF 50K 10K GAIN = 5 * Circuit Drives Large Load Capacitance ≤ 4000pF OUTPUT .01µF + 0.1µF + - 2.5V 10M PHOTO DETECTOR CURRENT TO VOLTAGE CONVERTER WIEN BRIDGE OSCILLATOR (RAIL-TO-RAIL) SINE WAVE GENERATOR RF = 5M +2.5V - I OUTPUT + -2.5V +2.5V - 10K VOUT = I x RF PHOTODIODE 10K .01µF C = .01µF + f =~ -2.5V 10K R = 10K 1 2πRC RL = 10K ~ 1.6KHz * See rail to rail waveform ULTRA LONG TIME CONSTANT INTEGRATOR INTEGRATOR VOLTAGE PRESET 20K 20K 5V Relay 1 2 R 7 - t2 + 3 + 5V 4 6 t1 1/2 ALD2301 0.1 -5 V * LOW LEAKAGE CAPACITOR e.g. TEFLON CAPACITOR TYPE K11B104KSW Component Research Inc. • All capacitance values are in µF unless otherwise specified. • RELAYS 1 & 2 are of type 4705, Gordos Corporation. ALD1712A/ALD1712B ALD1712 1.5V VIN = dt ALD1712 3 8 0.1 V = 1/RC Control 1 - 1 +5V Relay 2 VIN 1/2 ALD2301 5V 2 C* Advanced Linear Devices - 7 4 + Control 2 6 5 1.5V 6 of 9 SOIC-8 PACKAGE DRAWING 8 Pin Plastic SOIC Package E Millimeters Dim S (45°) D A Min 1.35 Max 1.75 Min 0.053 Max 0.069 A1 0.10 0.25 0.004 0.010 b 0.35 0.45 0.014 0.018 C 0.18 0.25 0.007 0.010 D-8 4.69 5.00 0.185 0.196 E 3.50 4.05 0.140 0.160 1.27 BSC e A A1 e Inches 0.050 BSC H 5.70 6.30 0.224 0.248 L 0.60 0.937 0.024 0.037 ø 0° 8° 0° 8° S 0.25 0.50 0.010 0.020 b S (45°) H L ALD1712A/ALD1712B ALD1712 C ø Advanced Linear Devices 7 of 9 PDIP-8 PACKAGE DRAWING 8 Pin Plastic DIP Package Millimeters E E1 D S A2 A1 e b A L Dim Min Max Min Max A 3.81 5.08 0.105 0.200 A1 0.38 1.27 0.015 0.050 A2 1.27 2.03 0.050 0.080 b 0.89 1.65 0.035 0.065 b1 0.38 0.51 0.015 0.020 c 0.20 0.30 0.008 0.012 D-8 9.40 11.68 0.370 0.460 E 5.59 7.11 0.220 0.280 E1 7.62 8.26 0.300 0.325 e 2.29 2.79 0.090 0.110 e1 7.37 7.87 0.290 0.310 L 2.79 3.81 0.110 0.150 S-8 1.02 2.03 0.040 0.080 0° 15° 0° 15° ø b1 Inches c e1 ALD1712A/ALD1712B ALD1712 ø Advanced Linear Devices 8 of 9 CERDIP-8 PACKAGE DRAWING 8 Pin CERDIP Package E E1 Millimeters D A1 s A L L2 b b1 e L1 Inches Dim A Min Max 3.55 5.08 Min 0.140 Max 0.200 A1 1.27 2.16 0.050 0.085 b 0.97 1.65 0.038 0.065 b1 0.36 0.58 0.014 0.023 C 0.20 0.38 0.008 0.015 D-8 -- 10.29 -- 0.405 E 5.59 7.87 0.220 0.310 E1 7.73 8.26 0.290 0.325 e 2.54 BSC 0.100 BSC e1 7.62 BSC 0.300 BSC L 3.81 5.08 0.150 0.200 L1 3.18 -- 0.125 -- L2 0.38 1.78 0.015 0.070 S -- 2.49 -- 0.098 Ø 0° 15° 0° 15° C e1 ALD1712A/ALD1712B ALD1712 ø Advanced Linear Devices 9 of 9