3976

Page 1 of 5 3976 ADVANCED DATASHEET - 02/19/99 (Subject to change without notice) DUAL FULL BRIDGE PROTECTED MOTOR DRIVER The A3976 is designed to drive both windings of a bipolar stepper motor or bidirectionally control two DC Motors. Both H-Bridges are capable of continuous output currents of up to +/- 500 mA and operating voltages to 30V. Free wheeling, substrate isolated diodes are included for output transient suppression when switching motors or other inductive loads. For each bridge the PHASE input controls load current polarity by selecting the appropriate source and sink driver pair. The ENABLE input, when held high, enables the respective output H-bridge. When both ENABLE pins are held low the device will enter SLEEP mode and consume less than 100µA. The 3976 is protected to ensure safe operation in harsh operating environments and was designed specifically for automotive applications. Protection circuitry will check for open or shorted load, motor lead short to ground or supply, VBB overvoltage, VCC undervoltage, and thermal shutdown. If any of these conditions are detected the outputs will be disabled and fault information will be output to diagnostic pins FAULT1 and FAULT2. The 3976 is supplied in a choice of two power packages, a 16-lead plastic DIP with a copper batwing tab (suffix ‘B’), and a 24-lead plastic SOIC with a copper batwing tab (suffix ‘LB’). In both cases, the power tab is at ground potential and needs no electrical isolation. VBB 1 ENABLE1 2 PHASE1 3 n/c 4 n/c 5 GROUND 6 GROUND 7 n/c 8 OUT1A 9 n/c 10 FAULT1 11 OUT1B 12 24 VCC 23 ENABLE2 22 PHASE2 21 n/c 20 n/c A3976KLB 19 GROUND 18 GROUND 17 n/c 16 OUT2A 15 n/c 14 FAULT2 13 OUT2B ABSOLUTE MAXIMUM RATINGS at TA = +25°C Operating Supply Voltage, VBB .................... 30 V Non-Operating Supply Voltage..................... 35 V Output Current, IOUT ............................±500 mA* Logic Supply Voltage, VCC .......................... 7.0 V Fault Output Voltage ................................... 7.0 V Logic Input Voltage Range, VIN.......................... -0.3 V to VCC + 0.3 V Package Power Dissipation (TA = +25°C), PD A3976KLB.................................. 2.2 W A3976KB .................................... 2.9 W Operating Temperature Range, TA .............................. -40°C to +125°C Junction Temperature, TJ ......................... +150°C Storage Temperature Range, TS............................... -55°C to +150°C * Output current rating may be limited by duty cycle, ambient temperature, and heat sinking. Under any set of conditions, do not exceed the specified current rating or a junction temperature of 150°C. FEATURES n n n n n n n n n n n 30 V , ±500 mA Continuous Output Rating 35V Load Dump Survival Output Short Circuit Protection Coded Fault Diagnostic Outputs Low Current Standby Mode Open Load Monitor Low Current Standby Mode VBB Over Voltage Shutdown Internal Thermal Shutdown Circuitry Internal Low Parasitic Free Wheeling Diodes Crossover Current Protection PART NUMBER A3976KLB A3973KB PACKAGE 24 Lead SOIC 16 Lead DIP RØJA 56°C/W 43°C/W RØJT 6°C/W 6°C/W Page 2 of 5 3976 Dual Protected PWM Motor Driver Functional Block Diagram (one of two bridges shown) VCC Thermal Shutdown Over/Under Voltage Monitor Short to Supply Monitor VBB FAULT1 Diagnostic Logic FAULT2 To Bridge 2 PHASE1 OUT1A ENABLE1 PHASE2 CONTROL LOGIC OUT1B ENABLE2 OUT2A Input Pull Down To Bridge 2 OUT2B GROUND Short to Ground Monitor Input Logic PHASE X 0 1 ENABLE 0 1 1 OUTA Off Low High OUTB Off High Low Fault Logic Fault Condition Thermal Shutdown Short to Battery or Open Load Short to Ground Normal Operation FAULT1 Low Low High High FAULT2 Low High Low High Page 3 of 5 3976 Dual Protected PWM Motor Driver ELECTRICAL CHARACTERISTICS at TA = -40 °C to +125°C, VBB = 30 V, VCC = 5.0 V (Unless noted otherwise) Limits Characteristics Output Drivers Load Supply Voltage Range Logic Supply Range Output Current Limit VBB VCC ICL Operating Operating Outputs A or B = GROUND Outputs A or B = VBB Output Leakage Current ICEX VOUT = VBB VOUT = 0 V Output Saturation Voltage VCE(SAT) Source Driver, IOUT = -350 mA Source Driver, IOUT = -500 ma Sink Driver, IOUT = +350 mA Sink Driver, IOUT = +500 ma Clamp Diode Forward Voltage (Flyback or Ground Clamp) Control Logic Motor Supply Current (No Load) Logic Supply Current ICC IBB ENABLE1 = ENABLE2 = High Sleep Mode ENABLE1 = ENABLE2 = Low ENABLE1 = ENABLE2 = High Sleep Mode, ENABLE1 = ENABLE2 = Low Logic Input Voltage – – – – 0.7VCC – VIN = 5 V VIN = 0V – – 7 – 45 – – – 50 -1.0 10 25 50 75 .3VCC 100 -2.0 mA µA MA µA V V µA µA VF IF = 500 mA (Sink / Ground Clamp) IF = 500 mA (Source / Flyback) 6 4.5 0.7 0.7 – – – – – – – – 1.1 1.1