A3134ELT

A3134 Bipolar Hall Effect Switch for High-Temperature Operation Discontinued Product These parts are no longer in production The device should not be purchased for new design applications. Samples are no longer available. Date of status change: October 31, 2005 Recommended Substitutions: For new customers and applications, refer to the A1201 NOTE: For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative. Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use. 3134 BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMPERATURE OPERATION This low-hysteresis bipolar Hall-effect switch is an extremely temperature-stable and stress-resistant sensor especially suited for operation over extended temperature ranges to +150°C. Superior high-temperature performance is made possible through a novel Schmitt trigger circuit that maintains operate and release point stability by compensating for temperature changes in the Hall element. Additionally, internal compensation provides magnetic switch points that become more sensitive with temperature, hence offsetting the usual degradation of the magnetic field with temperature. Its low hysteresis makes this device ideal for detecting small changes in magnetic field strength or for use with inexpensive magnets. The device includes on a single silicon chip a voltage regulator, quadratic Hall-voltage generator, temperature compensation circuit, signal amplifier, Schmitt trigger, and a buffered open-collector output to sink up to 25 mA. The on-board regulator permits operation with supply voltages of 4.5 volts to 24 volts. The first character of the part number suffix determines the device operating temperature range. Suffix ‘E–’ is for -40°C to +85°C, and suffix ‘L–’ is -40°C to +150°C. Two package styles provide a magnetically optimized package for most applications. Suffix ‘–LT’ is a miniature SOT89/TO-243AA transistor package for surface-mount applications while suffix ‘–UA’ is a three-lead ultra-mini-SIP. Data Sheet 27631.4D V X CC 1 2 3 GROUND Dwg. PH-003A Pinning is shown viewed from branded side. ABSOLUTE MAXIMUM RATINGS at TA = +25°C Supply Voltage, VCC ............................. 30 V Reverse Battery Voltage, VRCC .......... -30 V Magnetic Flux Density, B .......... Unlimited Output OFF Voltage, VOUT .................. 30 V Reverse Output Voltage, VOUT ........... -0.5 V Continuous Output Current, IOUT ............................................ 25 mA Operating Temperature Range, TA Suffix ‘E–’ .................. -40°C to +85°C Suffix ‘L–’ ................ -40°C to +150°C Storage Temperature Range, TS .............................. -65°C to +170°C OUTPUT SUPPLY FEATURES s Superior Temperature Stability s Operation From Unregulated Supply s Open-Collector 25 mA Output s Reverse Battery Protection s Activate With Small, Commercially Available Permanent Magnets s Solid-State Reliability s Small Size s Resistant to Physical Stress Always order by complete part number, e.g., A3134ELT . 3134 LOW-HYSTERESIS BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMP. OPERATION FUNCTIONAL BLOCK DIAGRAM 1 VCC REG. X 3 OUTPUT GROUND 2 Dwg. FH-005-3 ELECTRICAL CHARACTERISTICS over operating temperature range, at VCC = 12 V. Limits Characteristic Supply Voltage Output Saturation Voltage Output Leakage Current Supply Current Output Rise Time Output Fall Time Symbol VCC VOUT(SAT) IOFF ICC tr tf Test Conditions Operating IOUT = 20 mA, B > BOP VOUT = 24 V, B < BRP B < BRP (Output OFF) B > BOP (Output ON) RL = 820 Ω, CL = 20 pF RL = 820 Ω, CL = 20 pF Min. 4.5 — — — — — — Typ. — 175 0.05 3.2 5.0 100 100 Max. 24 400 1.0 9.0 — — — Units V mV µA mA mA ns ns MAGNETIC CHARACTERISTICS over oper. temp. and oper. supply voltage ranges. Limits Characteristic Operate Point Release Point Hysteresis Symbol BOP BRP Bhys Test Conditions Min. -40 -50 5.0 Typ. 8.5 -19 27 Max. 60 50 55 Units G G G NOTES: BOP = operate point (output turns ON); BRP = release point (output turns OFF); Bhys = hysteresis (BOP - BRP). As used here, negative flux densities are defined as less than zero (algebraic convention). Typical values are at TA = +25°C and VCC = 12 V. 1 gauss (G) is exactly equal to 0.1 millitesla (mT). 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright © 1995, 2003 Allegro MicroSystems, Inc. 3134 LOW-HYSTERESIS BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMP. OPERATION TYPICAL OPERATING CHARACTERISTICS SWITCH POINTS 40 50 HYSTERESIS 40 VCC = 4.5 V–24 V 20 SWITCH POINT IN GAUSS OPERATE POINT HYSTERESIS IN GAUSS 30 0 20 -20 RELEASE POINT VCC = 4.5 V–24 V 10 -40 -50 0 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 Dwg. GH-051 AMBIENT TEMPERATURE IN °C Dwg. GH-052 AMBIENT TEMPERATURE IN ° C OUTPUT SATURATION VOLTAGE 300 5.0 SUPPLY CURRENT I OUT = 20 mA V CC = 4.5–24 V B < B RP 4.0 SATURATION VOLTAGE IN mV 200 SUPPLY CURRENT IN mA V CC = 24 V 3.0 VCC = 4.5 V V CC = 12 V 100 2.0 0 -50 1.0 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE IN ° C Dwg. GH-029 AMBIENT TEMPERATURE IN °C Dwg. GH-053 www.allegromicro.com 3134 LOW-HYSTERESIS BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMP. OPERATION (±0.005" [0.13 mm] die placement) Suffix “LT” ACTIVE AREA DEPTH 0.0305" 0.775 mm NOM 0.090" 2.27 mm 0.050" 1.27 mm SENSOR LOCATIONS APPLICATIONS INFORMATION Extensive applications information for Hall-effect sensors is available in: • Hall-Effect IC Applications Guide, Application Note 27701; • Hall-Effect Devices: Soldering, Gluing, Potting, Encapsulating, and Lead Forming, Application Note 27703.1; • Soldering of Through-Hole Hall-Sensor Dervices, Application Note 27703; and • Soldering of Surface-Mount Hall-Sensor Devices, Application Note 27703.2. All are provided in Allegro Electronic Data Book, AMS-702. or at www.allegromicro.com A 1 2 3 OPERATION Dwg. MH-008-4C Suffix “UA” ACTIVE AREA DEPTH 0.0195" 0.50 mm NOM 0.083" 2.10 mm The output of these devices (pin 3) switches low when the magnetic field at the Hall sensor exceeds the operate point threshold (BOP). At this point, the output voltage is VOUT(SAT). When the magnetic field is reduced to below the release point (BRP) the device output goes high. Note especially that release can occur when the magnetic field is removed but to ensure release, a field reversal is required. The difference in the magnetic operate and release points is called the hysteresis (Bhys) of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical vibration and electrical noise. Powering up the device in the absence of a magnetic field (less than BOP and higher than BRP) will allow in indeterminate output state. The correct state is warranted after the first excursion beyond BOP or BRP. 0.060" 1.51 mm A BRANDED SURFACE 1 2 3 Dwg. MH-011-4C The products described herein are manufactured under one or more of the following U.S. patents: 5,045,920; 5,264,783; 5,442,283; 5,389,889; 5,581,179; 5,517,112; 5,619,137; 5,621,319; 5,650,719; 5,686,894; 5,694,038; 5,729,130; 5,917,320; and other patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support appliances, devices, or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties that may result from its use. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 3134 LOW-HYSTERESIS BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMP. OPERATION PACKAGE DESIGNATOR ‘LT’ (SOT89/TO-243AA) Dimensions in Inches (for reference only) Dimensions in Millimeters (controlling dimensions) 0.181 0.173 0.072 0.064 0.167 0.155 0.102 0.090 0.063 0.055 0.0173 0.0138 4.60 4.40 1.83 1.62 4.25 3.94 2.60 2.29 1.60 1.40 0.44 0.35 1 2 3 0.090 0.084 1 2 3 2.29 2.13 0.047 0.035 0.059 BSC 0.0189 0.0142 0.0221 0.0173 0.118 BSC Dwg. MA-009-3A in 1.20 0.89 1.50 BSC 0.48 0.36 0.56 0.44 3.00 BSC Dwg. MA-009-3A mm 0.098 0.079 B A 0.031 0.102 0.181 3 0.047 0.031 TYP 2.5 2.0 B A 0.8 2.6 4.6 1.2 0.8 TYP 1 0.028 TYP 2 1 0.7 TYP 2 3 Pads 1, 2, 3, and A — Standard SOT89 Layout Pads 1, 2, 3, and B — Low-Stress Version Pads 1, 2, and 3 only — Lowest Stress, But Not Self Aligning Dwg. MA-012-3 in Pads 1, 2, 3, and A — Standard SOT89 Layout Pads 1, 2, 3, and B — Low-Stress Version Pads 1, 2, and 3 only — Lowest Stress, But Not Self Aligning Dwg. MA-012-3 mm NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Supplied in bulk pack (500 pieces per bag) or add "TR" to part number for tape and reel. 3. Only low-temperature (≤240°C) reflow-soldering techniques are recommended for SOT89 devices. www.allegromicro.com 3134 LOW-HYSTERESIS BIPOLAR HALL-EFFECT SWITCH FOR HIGH-TEMP. OPERATION PACKAGE DESIGNATOR ‘UA’ Dimensions in Inches (controlling dimensions) 0.164 0.159 Dimensions in Millimeters (for reference only) 4.17 4.04 45° 0.062 0.058 45° 1.57 1.47 0.122 0.117 45° 0.031 3.10 2.97 45° 0.79 0.085 MAX 1 2 3 2.16 MAX 1 2 3 0.640 0.600 0.0173 0.0138 16.26 15.24 0.44 0.35 SEE NOTE 0.0189 0.0142 SEE NOTE 0.48 0.36 0.050 BSC Dwg. MH-014E in 1.27 BSC Dwg. MH-014E mm Radial Lead Form (order A3240xUA-LC) NOTES: 1. Tolerances on package height and width represent allowable mold offsets. Dimensions given are measured at the widest point (parting line). 2. Exact body and lead configuration at vendor’s option within limits shown. 3. Height does not include mold gate flash. 4. Recommended minimum PWB hole diameter to clear transition area is 0.035" (0.89 mm). 5. Where no tolerance is specified, dimension is nominal. 6. Supplied in bulk pack (500 pieces per bag). 1 2 3 0.620" 0.500" (15.7 mm 12.7 mm) 0.108" (2.74 mm) 0.100" (2.5 mm) Dwg. MH-026 NOTE: Lead-form dimensions are the nominals produced on the forming equipment. No dimensional tolerance is implied or guaranteed for bulk packaging (500 pieces per bag). 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000