UCN5832EP

5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS 5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS Intended originally to drive thermal printheads, the UCN5832A and UCN5832EP have been optimized for low output-saturation voltage, high-speed operation, and pin configurations most convenient for the tight space requirements of high-resolution printheads. These integrated circuits can also be used to drive multiplexed LED displays or incandescent lamps at up to 150 mA peak current. The combination of bipolar and MOS technologies gives BiMOS II arrays an interface flexibility beyond the reach of standard buffers and power driver circuits. The devices each have 32 bipolar NPN open-collector saturated drivers, a CMOS data latch for each of the drivers, two 16-bit CMOS shift registers, and CMOS control circuitry. The high-speed CMOS shift registers and latches allow operation with most microprocessor based systems. Use of these drivers with TTL may require input pull-up resistors to ensure an input logic high. MOS serial data outputs permit cascading for interface applications requiring additional drive lines. The UCN5832A is supplied in a 40-pin dual in-line plastic package with 0.600" (15.24 mm) row spacing. Under normal operating conditions, this device will allow all outputs to sustain 100 mA continuously without derating. The UCN5832EP is supplied in a 44-lead plastic leaded chip carrier for minimum area, surface-mount applications. Both devices are also available for operation from -40°C to +85°C. To order, change the prefix from ‘UCN’ to ‘UCQ’. Similar 32-bit serial-input latched source drivers are available as the UCN5818AF/EPF. Other high-voltage, high-current 8-bit devices are available as the UCN5821A, UCN5841A/LW, and UCN5842A. Data Sheet 26185.10B UCN5832A LOGIC SUPPLY SERIAL DATA IN GROUND STROBE OUT 1 OUT OUT OUT 2 3 1 2 3 4 5 6 7 8 REGISTER REGISTER LATCHES V DD 40 CLOCK 39 38 37 36 35 34 33 32 SERIAL DATA OUT OUTPUT ENABLE OUT 32 OUT 31 OUT 30 OUT 29 OUT 28 OUT 27 4 5 6 OUT 10 11 12 12 LATCHES OUT 9 31 OUT 26 30 OUT 25 29 28 27 26 25 24 OUT 24 OUT 23 OUT 22 OUT 21 OUT 20 OUT 19 OUT 7 OUT 8 OUT 9 OUT 10 14 OUT 11 15 OUT 12 16 OUT 13 17 OUT 14 18 OUT 15 19 OUT 16 20 23 OUT 18 22 OUT 17 21 INTERNAL CONNECTION Dwg. No. A-12,377A ABSOLUTE MAXIMUM RATINGS at +25°C Free-Air Temperature Output Voltage, VOUT ...................... 40 V Logic Supply Voltage, VDD ................ 15 V Input Voltage Range, VIN ................... -0.3 V to V DD + 0.3 V Continuous Output Current, lOUT .................................. 150 mA Package Power Dissipation, PD ................................ See Graph Operating Temperature Range, TA ........................... -20°C to +85 °C Storage Temperature Range, TS .......................... -55°C to +150°C Caution: CMOS devices have input-static protection but are susceptible to damage when exposed to extremely high static electrical charges. FEATURES s s s s s To 3.3 MHz Data Input Rate Low-Power CMOS Logic and Latches 40 V Current Sink Outputs Low Saturation Voltage Automotive Capable Always order by complete part number: Part Number UCN5832A UCN5832EP Package 40-Pin DIP 44-Lead PLCC 5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS 3.0 ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS FUNCTIONAL BLOCK DIAGRAM 2.5 SUFFIX 'A', R θJA = 36°C/W V DD CLOCK 32-BIT SHIFT REGISTER 2.0 SERIAL DATA IN LATCHES SERIAL DATA OUT 1.5 SUFFIX 'EP', RθJA = 46°C/W STROBE 1.0 OUTPUT ENABLE MOS BIPOLAR 0.5 OUT1 OUT2 OUT3 GROUND OUT30 OUT31 OUT32 0 25 50 75 100 125 AMBIENT TEMPERATURE IN °C 150 Dwg. GP-025A UCN5832EP SERIAL DATA OUT 32 GROUND STROBE OUTPUT ENABLE LOGIC SUPPLY SERIAL DATA IN CLOCK OUT32 41 OUT1 NC 44 43 VDD 1 42 40 5 6 4 3 2 NC OUT 2 7 8 9 10 39 OUT31 38 37 SHIFT REGISTER SHIFT REGISTER 36 LATCHES LATCHES 11 12 13 14 15 16 35 34 33 32 31 30 29 OUT21 OUT12 17 OUT 13 19 20 21 OUT 16 22 IC 23 OUT 17 24 25 26 OUT 20 27 NC 18 NC 28 Dwg. No. A-14,360 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright © 1984, 1998, Allegro MicroSystems, Inc. 5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS ELECTRICAL CHARACTERISTICS at TA = +25°C, VDD = 5 V (unless otherwise noted). Characteristic Output Leakage Current Collector-Emitter Saturation Voltage Symbol ICEX VCE(SAT) Test Conditions VOUT = 40 V, TA = 70 °C lOUT = 50 mA lOUT = 100 mA, “A” package lOUT = 100 mA, “EP” package Input Voltage VIN(1) VIN(0) Input Current lIN(1) lIN(0) Input lmpedance Serial Data Output Resistance Supply Current ZIN ROUT lDD One output ON, lOUT = 100 mA All outputs OFF Output Rise Time Output Fall Time tr tf lOUT = 100 mA, 10% to 90% lOUT = 100 mA, 90% to 10% VIN = 3.5 V VIN = 0.8 V VIN = 3.5 V Min. — — 150 — 3.5 -0.3 — — 3.5 — — — — — Limits Max. 10 275 550 550 5.3 +0.8 1.0 -1.0 — 20 5.0 50 1.0 1.0 Units µA mV mV mV V V µA µA MΩ kΩ mA µA µs µs NOTE: Positive (negative) current is defined as going into (coming out of) the specified device pin. TYPICAL INPUT CIRCUIT VDD TYPICAL OUTPUT DRIVER VDD IN 675Ω OUT Dwg. No. A-12,379A Dwg. No. A-12,380A 5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS CLOCK DATA IN E STROBE OUTPUT ENABLE G OUTN Dwg. No. A-12,276A A B D F C Serial Data present at the input is transferred to the shift register on the logic “0” to logic “1” transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift data information towards the SERIAL DATA OUTPUT. The SERIAL DATA must appear at the input prior to the rising edge of the CLOCK input waveform. Information present at any register is transferred to its respective latch when the STROBE is high (serial-to-parallel conversion). The latches will continue to accept new data as long as the STROBE is held high. Applications where the latches are bypassed (STROBE tied high) will require that the OUTPUT ENABLE input be low during serial data entry. When the OUTPUT ENABLE input is low, all of the output buffers are disabled (OFF) without affecting the information stored in the latches or shift register. With the OUTPUT ENABLE input high, the outputs are controlled by the state of the latches. TIMING CONDITIONS (VDD = 5.0 V, Logic Levels are VDD and Ground) A. Minimum Data Active Time Before Clock Pulse (Data Set-Up Time) .......................................................................... 75 ns B. Minimum Data Active Time After Clock Pulse (Data Hold Time) ............................................................................. 75 ns C. Minimum Data Pulse Width ................................................................ 150 ns D. Minimum Clock Pulse Width ............................................................... 150 ns E. Minimum Time Between Clock Activation and Strobe ....................... 300 ns F. Minimum Strobe Pulse Width ............................................................. 100 ns G. Typical Time Between Strobe Activation and Output Transition ........................................................................... 500 ns TRUTH TABLE Serial Shift Register Contents Data Clock Input Input I1 I2 I3 ... IN-1 IN H L X H L R1 R2 ... R1 R2 ... X X ... RN-2 RN-1 RN-2 RN-1 RN-1 RN X X PN-1 PN Serial Data Strobe Output Input RN-1 RN-1 RN X PN L H R1 R2 R3 ... P1 P2 P3 ... X L = Low Logic Level H = High Logic Level X = Irrelevant Latch Contents I1 I2 I3 ... IN-1 IN Output Enable Input Output Contents I1 I2 I3 ... IN-1 I N R1 R2 R3 ... X P1 P2 P3 ... RN-1 RN PN-1 PN X X H L P1 P2 P3 ... PN-1 PN H H H ... H H X X ... P = Present State R = Previous State 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS UCN5832A Dimensions in Inches (controlling dimensions) 0.015 0.008 21 40 0.700 MAX 0.580 0.485 0.600 BSC 1 2 0.070 0.030 3 4 2.095 1.980 20 0.100 BSC 0.005 MIN 0.250 MAX 0.015 MIN 0.200 0.115 0.022 0.014 Dwg. MA-003-40 in Dimensions in Millimeters (for reference only) 0.381 0.204 21 40 17.78 14.73 12.32 MAX 15.24 BSC 1 2 1.77 0.77 3 4 53.2 50.3 2.54 BSC 20 0.13 MIN 6.35 MAX 0.39 MIN 5.08 2.93 0.558 0.356 Dwg. MA-003-40 mm NOTES: 1. Lead thickness is measured at seating plane or below. 2. Lead spacing tolerance is non-cumulative. 3. Exact body and lead configuration at vendor’s option within limits shown. 5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS UCN5832EP Dimensions in Inches (controlling dimensions) 28 18 29 0.319 0.291 0.021 0.013 0.695 0.685 0.656 0.650 0.319 0.291 0.050 BSC INDEX AREA 17 0.032 0.026 39 7 40 0.020 MIN 44 1 2 6 0.656 0.650 0.695 0.685 Dwg. MA-005-44A in 0.180 0.165 Dimensions in Millimeters (for reference only) 28 18 29 8.10 7.39 0.533 0.331 17.65 17.40 16.662 16.510 INDEX AREA 17 0.812 0.661 8.10 7.39 1.27 BSC 39 7 40 0.51 MIN 44 1 2 6 4.57 4.20 16.662 16.510 17.65 17.40 Dwg. MA-005-44A mm NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS 5832 BiMOS II 32-BIT SERIAL-INPUT, LATCHED DRIVERS BiMOS II (Series 5800) & DABiC IV (Series 6800) INTELLIGENT POWER INTERFACE DRIVERS SELECTION GUIDE Function 8-Bit (saturated drivers) 8-Bit 8-Bit 8-Bit 8-Bit 9-Bit 10-Bit (active pull-downs) 12-Bit (active pull-downs) 20-Bit (active pull-downs) 32-Bit (active pull-downs) 32-Bit 32-Bit (saturated drivers) Output Ratings * SERIAL-INPUT LATCHED DRIVERS -120 mA 350 mA 350 mA 350 mA 350 mA 1.6 A -25 mA -25 mA -25 mA -25 mA 100 mA 100 mA 50 V‡ 50 V 80 V 50 V‡ 80 V‡ 50 V 60 V 60 V 60 V 60 V 30 V 40 V Part Number † 5895 5821 5822 5841 5842 5829 5810-F and 6809/10 5811 and 6811 5812-F and 6812 5818-F and 6818 5833 5832 PARALLEL-INPUT LATCHED DRIVERS 4-Bit 8-Bit 8-Bit 350 mA -25 mA 350 mA 50 V‡ 60 V 50 V‡ 5800 5815 5801 SPECIAL-PURPOSE FUNCTIONS Unipolar Stepper Motor Translator/Driver Addressable 28-Line Decoder/Driver * † ‡ 1.25 A 450 mA 50 V‡ 30 V 5804 6817 Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits. Negative current is defined as coming out of (sourcing) the output. Complete part number includes additional characters to indicate operating temperature range and package style. Internal transient-suppression diodes included for inductive-load protection. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000