UDN5713M

5713 DUAL PERIPHERAL AND POWER DRIVER 5713 Data Sheet 29307B DUAL PERIPHERAL AND POWER DRIVER — TRANSIENT PROTECTED OUTPUTS Supply Voltage, VCC . . . . . . . . . . . . . . 7.0 V Input Voltage, VIN . . . . . . . . . . . . . . . . . 30 V Output Off-State Voltage, VOFF . . . . . . . . . . . . . . . . . . . . . . . . 80 V Output On-State Sink Current, ION . . . . . . . . . . . . . . . . . . . . . . 600 mA Suppression Diode Off-State Voltage, VOFF . . . . . . . . . . . . . . . . . . . . . . . . 80 V Suppression Diode On-State Current, ION . . . . . . . . . . . . . . . . . . . . . . 600 mA Power Dissipation at TA = 25°C, PD Package . . . . . . . . . . . . . . . . . . . 1.5 W* Each Driver . . . . . . . . . . . . . . . . . 0.8 W Operating Free-Air Temperature Range, TA . . . . . . . . . . . . . . . . . -20°C to +85°C Storage Temperature Range, TS . . . . . . . . . . . . . . . . -55°C to +150°C *Derate at the rate of 12.5 mW/°C above TA = 25°C. T C UY DL ON RO PE DC EN UE IN ER TF NE OR CR IS O DF — The UDN5713M dual driver is ideally suited for interface between low-level or high-level logic and high-current/high-voltage loads. Typical applications include driving peripheral loads such as incandescent lamps, light-emitting diodes, memories, and heaters with a load current of up to 600 mA. The integral transient suppression diodes allow the use of these drivers with inductive loads such as relays, solenoids, or stepping motors without the need for discrete diodes. Similar devices with four drivers per package are the 5703 and 5706. Dwg. No. A-9789 This “mini-DlP” dual peripheral and power driver is a bipolar monolithic integrated circuit incorporating NOR logic gates, highcurrent switching transistors, and transient suppression diodes on the same chip. The two output transistors are capable of simultaneously sinking 300 mA continuously at ambient temperatures of up to +70°C. In the OFF state, this driver will withstand at least 80 V. FEATURES s s s s ABSOLUTE MAXIMUM RATINGS DTL/TTL/PMOS/CMOS Compatible Inputs Low Input Current 300 mA Continuous Output Current Stand-off Voltage of 80 V Always order by complete part number, e.g., UDN5713M . 5713 DUAL PERIPHERAL AND POWER DRIVER RECOMMENDED OPERATING CONDITIONS Min. Supply Voltage (VCC) Operating Temperature Range Current into any output (ON state) 4.75 0 — Nom. 5.0 +25 — Max. 5.25 +85 300 Units V °C mA ELECTRICAL CHARACTERISTICS over operating temperature range (unless otherwise noted). Test Conditions Characteristic “1” Input Voltage “0” Input Voltage “0” Input Current at all Inputs except Strobe “0” Input Current at Strobe “1” Input Current at all Inputs except Strobe “1” Input Current at Strobe Input Clamp Voltage Symbol VIN(1) VIN(0) IIN(0) IIN(0) IIN(1) IIN(1) VIK Temp. — — — — — — — VCC MIN MIN MAX MAX MAX MAX MIN Driven Input — — 0.4 V 0.4 V 30 V 30 V -12 mA Other Input — — 30 V 30 V 0V 0V — Output — — — — — — — Min. 2.0 — — — — — — Limits Typ. — — -50 -100 — — — Max. Units — 0.8 -100 -200 10 20 -1.5 V V µA µA µA µA V Notes — — 2 — 2 — — SWITCHING CHARACTERISTICS at VCC = 5.0 V, TA = 25°C Limits Characteristic Turn-on Delay Time Symbol tpd0 Test Conditions VS = 70 V, RL = 465 Ω (10 Watts), CL = 15 pF Turn-off Delay Time tpd1 VS = 70 V, RL = 465 Ω (10 Watts), CL = 15 pF NOTES: 1. Typical values are at VCC = 5.0 V, TA = 25°C. 2. Each input tested separately. 3. Voltage values shown in the test circuit waveforms are with respect to network ground terminal. 4. Capacitance values specified include probe and test fixture capacitance. Min. — Typ. 200 Max. Units 500 ns Notes 3 — 300 750 ns 3 INPUT PULSE CHARACTERISTICS VIN(0) = 0 V VIN(1) = 3.5 V tf = 7 n s tr = 14 ns tp = 1 µ s PRR = 500 kHz 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 W Copyright © 1976, 1997, Allegro MicroSystems, Inc. 5713 DUAL PERIPHERAL AND POWER DRIVER ELECTRICAL CHARACTERISTICS over operating temperature range (unless otherwise noted). Test Conditions Characteristic “1” Output Reverse Current “0” Output Voltage Diode Leakage Current Diode Forward Voltage Drop “1” Level Supply Current “0” Level Supply Current Symbol lOFF VON ILK VD lCC(1) lCC(0) Temp. — — — — NOM NOM NOM NOM VCC MIN OPEN MIN MIN NOM NOM MAX MAX Driven Input 2.0 V 2.0 V 0.8 V 0.8 V 0V VCC 5.0 V 0V Other Input 0V 0V 0.8 V 0.8 V 0V VCC 5.0 V 0V Output 80 V 80 V 150 mA 300 mA OPEN — — — Min. — — — — — — — — Limits Typ. — — 0.35 0.5 — 1.5 8.0 36 Max. Units 100 100 0.5 0.7 200 1.75 13 50 µA µA V V µA V mA mA Notes — — — — 3 4 1, 2 1, 2 NOTES: 1. Typical values are at VCC = 5.0 V, TA = 25°C. 2. Per package. 3. Diode leakage current measured at VR = 80 V. 4. Diode forward voltage drop measured at IF = 300 mA. 5. Capacitance values specified include probe and test fixture capacitance. Dwg. No. A-9123A Dwg. No. A-7628C 5713 DUAL PERIPHERAL AND POWER DRIVER Dimensions in Inches 8 5 0.014 0.008 0.430 0.280 0.240 MAX 0.300 BSC 1 0.070 0.045 4 0.005 0.400 0.355 MIN 0.210 MAX 0.015 MIN 0.150 0.115 0.022 0.014 0.100 BSC Dwg. MA-001-8A in Dimensions in Millimeters (Based on 1” = 25.4 mm) 8 5 0.355 0.204 10.92 7.11 6.10 MAX 7.62 BSC 1 1.77 1.15 4 0.13 10.16 9.02 MIN 5.33 MAX 0.39 MIN 3.81 2.93 0.558 0.356 2.54 BSC Dwg. MA-001-8A mm Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. NOTES: 1. Lead thickness is measured at seating plane or below. The information included herein is believed to be accurate and reliable. 2. Lead spacing tolerance is non-cumulative. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor 3. Exact body and lead configuration at vendor’s option for any infringements of patents or other rights of third parties which may result within limits shown. from its use. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000