440G-MT47043

Interlock Switches Guard Locking Switches 440G-MT Specifications Standards EN954-1, ISO13849-1, IEC/EN602041, NFPA79, EN1088, ISO14119, IEC/ EN60947-5-1, ANSI B11.19, AS4024.1 Cat. 1 Device per EN954-1 Dual channel interlocks suitable for Cat. 3 or 4 systems cULus, TUV 4 N.C., 3 N.C., 2 N.C. direct opening action 1 N.O., 2 N.O. AC 15 AC (Ue) 250V (le) 2A DC 250V 0.5A, 24V 2A 500V 500VA 5A 5V, 5mA DC > 2mm contact block (Ui) 500V (Uimp) 2500V 1 N.O. 3 15mm (0.59in) 6N (1.35lbs) 160mm per sec (6.3 in. per sec) 2 Cycle per sec Painted zinc alloy Stainless Steel IP67 3 x M20, 3 x 1/2in NPT or quick disconnect style -25°C to +60°C (13°F to +140°F) 4 x M5 1,000,000 cycles 1,000,000 cycles 1400g (3.08lbs) Red Fixing Bolts 1.6Nm Lid Screws 1.6Nm Terminal Screws 1.6Nm Max Holding Force Min Operating Radius Power Supply Solenoid Power Solenoid Rating 1600N (360lbs) 60mm (2.36in) 24V AC/DC or 110V AC or 230V AC 13W typical 100% ED 100% Category Approvals Safety Contacts Auxiliary Contacts Utilisation Category Description The 440G-MT solenoid switch is a positive mode, tongue operated guard locking interlock switch that locks a machine guard closed until power is isolated and ensures that it remains isolated while the guard is open. The guard may only be opened when a signal is applied to the internal solenoid which releases the lock mechanism. The 440G-MT locking mechanism withstands forces up to 1600N (360lbs) and the die-cast alloy housing is ideal for use in harsh environments. The 440G-MT solenoid switch is designed for machines that do not stop immediately or where premature interruption of the machine could cause damage to tooling and components or cause an additional hazard. Max. Switched Current/Volt/ Load Thermal Current (lth) Min Current Safety Contact Gap Rtd. Insulation Voltage Rtd. Impulse withstand Voltage Auxiliary Contacts Pollution Degree Actuator Travel for Positive Opening Break Contact Min Force Max Actuation Speed Max Actuation Frequency Case Material Actuator Material Protection Conduit Entry Operating Temperature Fixing Mechanical Life Electrical Life Weight Colour Torque Settings Features • Mechanical lock • High locking force—1600N (360lbs.) • Heavy duty die-cast alloy housing ideal for harsh environments 3-36 Interlock Switches Guard Locking Switches 440G-MT Product Selection Solenoid Voltage Contacts BBM/MBB Safety Aux. Actuator Standard 3 N.C. BBM 2 N.C. 2 N.O. 1 N.O. Fully-Flex — Standard Fully-Flex — — 4 N.C. — — Standard 3 N.C. BBM 2 N.C. 2 N.O. 1 N.O. Fully-Flex — 110V AC/DC Standard Fully-Flex — — BBM — 4 N.C. 3 N.C. 2 N.C. 4 N.C. — 1 N.O. 2 N.O. — — — — — M20 Conduit 440G-MT47037 440G-MT47038 440G-MT47007 440G-MT47044 440G-MT47045 440G-MT47010 440G-MT47031 440G-MT47070 440G-MT47071 440G-MT47013 440G-MT47077 440G-MT47078 440G-MT47012 440G-MT47033 440G-MT47016 440G-MT47015 440G-MT47035 Catalogue Number 1/2in NPT Adaptor 440G-MT47039 440G-MT47040 440G-MT47008 440G-MT47046 440G-MT47047 440G-MT47011 440G-MT47032 440G-MT47073 440G-MT47074 440G-MT47009 440G-MT47079 440G-MT47080 440G-MT47014 440G-MT47034 440G-MT47017 440G-MT47024 440G-MT47036 Quick Disconnect 440G-MT47041 440G-MT47042 440G-MT47043 440G-MT47048 440G-MT47049 440G-MT47050 440G-MT47069 440G-MT47075 440G-MT47076 440G-MT47072 440G-MT47081 440G-MT47082 440G-MT47083 440G-MT47106 440G-MT47107 440G-MT47108 440G-MT47111 889M-F12X9AE-2 24V AC/DC 230V AC/DC M23 mating cable 2m (6.5ft). See page 15-13 for details and additional lengths. Accessories Description For Dimensions refer to page Catalogue Number TLS-GD2 Standard Actuator 14-4 440G-A27011 Flat Actuator 14-5 440K-A11112 Fully-Flexible Actuator 14-4 440G-A27143 Sliding Bolt Actuator 14-4 440G-A27163 Extended Flat Actuator 14-5 440K-A17116 Replacement Cover No LED No Override Key — 440G-MT47120 3-37 Interlock Switches Guard Locking Switches 440G-MT Approximate Dimensions—mm (inches) Dimensions are not intended to be used for installation purposes. 4 x M5 144 (5.66) 5 (0.19) 40 (1.57) 30 (1.18) 38 (1.49) 9.2 (0.36) 40.7 (1.60) 46.75 (1.84) 199 (7.83) 20.5 (0.80) 46 (1.81) 8.75 (0.34) 15.5 (0.61) 23 (0.90) 2 x Manual Release Points 3-38 Interlock Switches Guard Locking Switches 440G-MT Typical Wiring Diagrams 4 N.C. + A2 12 22 32 42 AC/DC Solenoid Power + A2 3 N.C. + 1 N.O. AC/DC Solenoid Power + 2 N.C. + 2 N.O. AC/DC Solenoid Power A1 11 21 31 41 Solenoid 100% ED AC A1 12 22 32 44 Solenoid 100% ED AC A2 12 22 34 44 11 21 33 43 Solenoid 100% ED AC A1 11 21 31 43 4 N.C. Connector Pinout 1 3 4 6 7 8 2 5 9 10 12 Terminal A1 A2 11 12 21 22 31 32 41 42 Contact Solenoid Power N.C. N.C. N.C. N.C. 3 N.C. + 1 N.O. Terminal A1 A2 11 12 21 22 31 32 43 44 Contact Solenoid Power N.C. N.C. N.C. N.O. Ground 2 N.C. + 2 N.O. Terminal A1 A2 11 12 21 22 33 34 43 44 Contact Solenoid Power N.C. N.C. N.O. N.O. 8 7 6 5 12 9 11 1 10 2 3 4 Contact Action Contact Open Contact Closed Actuator withdrawal distance from full insertion 12 11/12 21/22 31/32 41/42 4 N.C. 6 0mm 3 N.C. + 1 N.O. (BBM) 12 11/12 21/22 31/32 43/44 6 0mm 2 N.C. + 2 N.O. (BBM) 12 11/12 21/22 33/34 43/44 6 0mm 3.5 3.5 3.5 3-39