800E-5PY

Emergency Stop Devices Push Buttons 800 E-Stops ! Specifications—22.5mm Front of Panel (Operators) Mechanical Ratings Description Vibration (assembled to panel) Shock Degree of protection Mechanical design life (typical) Plastic (800EP/ES) Metal (800EM/EB) Back of Panel Components Electrical Ratings Description Standard contact block ratings➋ 2-Across Style 3-Across Style NEMA, EEMAC NEMA, A600, A600, Q600, VDE Q600, 600V AC; 0660; AC15, DC 13 AC15, DC 13 to to IEC 947 IEC 947 10A max. 10A max. without continuous current enclosure (40°C to UL508, CSA22.2 (104°F) ambient) 6A #14, IEC 947, VDE with enclosure 0660, part 200 (60°C (140°F)) Conforming to CENELEC EN50013 Min of (1) #20AWG #18 to #12AWG Max of (2) (0.75 to 2.5mm 2) #14AWG or (1) Max (2) #14AWG #12AWG or (1) #12 AWG 2,200V for one minute 1,000,000 at 2A Finger-safe conforming to IP2X 10 to 2000Hz, 1.52mm displacement (peak-to-peak) max./10g max. 1/2 cycle sine wave for 11ms and no damage at 100g IP66 (NEMA Type 3, IP66 (NEMA Type 3, 3R, 4, 4X, 12, 13) 3R, 4, 12, 13) 500,000 cycles: mushroom 100,000 cycles: operators mushroom key operators (plastic), push-pull/twist 50,000 cycles: operators mushroom key operators (metal) -25°C to +55°C (-13°F to +131°F) ➋ -40°C to +70°C (85°C max. for 24 hours) -40°F to +158°F (185°F max. for 24 hours) Thermal current Terminal marking Wire capacity (screw terminal) Environmental Temperature range (operating): per IEC 947-1 Temperature range (short term storage): per IEC 947-1 Materials Bushings, mounting rings Dielectric strength (min) Electrical design life cycles Electrical shock protection: Per IEC 529 Mechanical Ratings Vibration Shock Glass-filled thermoplastic polyester, rated UL94 V-O Glass-filled thermoplastic polyester, rated UL94 V-O Silicone rubber Nitrile rubber Die-cast zinc; dark olive chromate finish Anodized aluminum (EB, EM, ES line) Bezels Contact block mechanical design Contact operation 10 to 2000Hz 1.52mm displacement (peakto-peak) max./10g max. 6hr 1/2 cycle sine wave for 11ms and no damage at 100g min 5,000,000 cycles 10 to 150Hz 0.15mm displacement (peakto-peak) max./2g max. 6hr 1/2 cycle sine wave for 11ms and no damage at 50g max Operating forces (typical) Environmental Temperature range Operating ➋➌ Short term storage ➌ Materials Springs Electrical contacts: Standard Low voltage Seals: diaphragm style Seals: lip and flat gasket styles Illuminated lenses N.C. slow make, double break (positive opening); N.C.L.B. late break, double break (positive opening) 2.78N: all contact 2.6N: each N.C. blocks contact block Transparent nylon Type 12 -25°C to +55°C (-13°F to +131°F) -25°C to +55°C (70°C max for 24 hrs) (-13°F to +131°F (158°F max for 24 hrs)) Stainless steel and zinc coated music wire ! See Performance Data: refer to page Important-2 of the A113 Industrial Controls catalogue. ➋ Operating temperature below 0°C (32°F) are based on the absence of freezing moisture and liquids. ➌ Per IEC 947-1. ➍ UL File & Guide Number E14840. Silver nickel alloy Fine silver Palladium silver Gold-plated over alloy: spanner; gold- silver plated silver nickel: stationary contacts Terminals: Screw type Plated steel Push-on type Agency approvals Approvals UL listed ➍/CSA certified Standard conformity UL508, UL486E NEMA ICS-1 and CSA22.2 #14, ICS-2 IEC 204-1, NEMA ICS-1 and 947; SEV 1005, ICS-2 (1983), IEC 1093; VDE 0113, 144, IEC 947-1, IEC 0660 Part 201; BS 947-5, VDE 0550, 4794; CEE 24; UL VDE 0660, Part 200 486E, UL 508, CSA22.2 #14 6-14 Emergency Stop Devices Push Buttons 800 E-Stops Product Selection—22.5mm 2-Position Push-Pull Operators, Non Illuminated—Twist-to-Release, Push-Pull 40mm Trigger Action Twist-to-Release Mushroom 40mm Twist-to-Release Mushroom 40mm Push-Pull Mushroom 800E-15YE112 Legend Plate for 40mm Ca Colour Operator Material Plastic Metal 40mm Mushroom Operator Twist-to-Release — Round (Trigger Action) ! Push-Pull Twist-to-Release — Round ➋ Push-Pull — Round ➋ Catalogue Number 800EP-MTS44 800EM-MTS44 800EP-MT4 800EM-MT4 800ES-MP24 800EM-MP24 Red Plastic Metal Plastic Metal 2-Position Trigger Action Operators, Non Illuminated—Key Release ➌ 40mm Key Release Mushroom 60mm Key Release Mushroom 800E-16YE112 Legend Plate for 60mm Cap Colour 2 Position Trigger Action ! Mushroom Operator Ronis Key Lock Size 40mm—Round 60mm—Round 40mm—Round 60mm—Round Catalogue Number 800EP-MKR44 800EP-MKR64 800EP-MKZ44 800EP-MKZ64 Red Zadi Key Lock Back-of-Panel Components, Non Illuminated Operators Mounting Latch and Contact Block Combination Mounting 2-Across Contact ➊➋ 1 N.C. Late break 1 N.O. - 1 N.C. Late break 1 N.C. Late break 1 N.O. - 1 N.C. Late break 1 N.C. Self-monitoring 3-Across 800E-3LX01S ! Trigger action operators are compliant with EN418 standards using standard N.C., N.C. Late Break, or N.C. Self-Monitoring contact blocks. Key Release operators are IP66, Type 4/13. ➋ Emergency stop push buttons are compliant with EN 418 standard when using N.C. Late break (N.C.L.B.) contact blocks. ➌ Key release operators are IP66, Type 4 and 13. 2-Across 3-Across Catalogue Number 800E-2LX01L 800E-2LX11L 800E-3LX01L 800E-3LX11L 800E-2LX01LS 3-Across 2-Across 6-15 Emergency Stop Devices Push Buttons 800 E-Stops Product Selection—22.5mm 2-Position Red Push-Pull Operators, Illuminated —Mushroom ➊ 40mm Mushroom Push-Pull 60mm Jumbo Mushroom Push-Pull 800E-15YE112 Legend Plate for 40mm Cap Operator Material Plastic Size 40mm 60mm 40mm Catalogue Number 800ES-LMP24 800ES-LMJP24 800EM-LMP24 800EM-LMJP24 Metal 60mm Back-of-Panel Components, Illuminated Operators 2-Across (5 ckts. max.) 3-Across (4 ckts. max.) Mounting Type Incandescent Volts 24 AC/DC 120 AC/DC Catalogue Number 800E-2DL3 800E-2DL5 800E-2DL3R 800E-2DL5R 800E-3DL3 800E-3DL5 800E-3DL3R 800E-3DL5R 800E-2TL5 800E-2TL7 800E-2TL5R 800E-2TL7R 800E-3TL5 800E-3TL7 800E-3TL5R 800E-3TL7R 2-Across 24 AC/DC LED (red) 120 AC 24 AC/DC Incandescent Full Voltage Power Module with Latch 3-Across LED (red) Incandescent 2-Across LED (red) Incandescent 3-Across Transformer Power Module with Latch 2-Across 3-Across 120 AC/DC 24 AC/DC 120 AC 24 AC/DC 120 AC/DC 24 AC/DC 120 AC 24 AC/DC 120 AC/DC 24 AC/DC LED (red) 120 AC 2-Across (3 ckts. max.) 3-Across (2 ckts. max.) 2-Across Late Break ! 800E-2X01L 1 N.C. Late break 800E-3X01L 3-Across Contact Blocks ! Emergency stop push buttons are compliant with EN 418 standard when using N.C.L.B. contact blocks. 6-16 Emergency Stop Devices Push Buttons 800 E-Stops ! Specifications—30.5mm Electrical Ratings Dielectric strength Electrical design life cycles Mechanical Ratings Vibration 2200V for one minute 1,000,000 at max. rated load 10 to 2000Hz 1.52mm displacement (peak-to-peak) max./10g max. (except Logic Reed) 1/2 cycle sine wave for 11ms ≥25g (contact fragility) and no damage at 100g Type 1, 4, 4X, 12, 13; watertight/oiltight IEC 529 IP66/65 Shock Degree of protection Mechanical design life cycles 250,000 min. (Push-pull/twist-to-release) Contact operation Shallow, mini, and low voltage contact blocks: Slow, double make and break. Typical operating forces 7.5lbs max. push or pull 2-position push-pull Environment Temperature range Operating➋ -40°C to +55°C (-40°F to +131°F) Storage -40°C to +85°C (-40°F to +185°F) Standard Contact Ratings Maximum thermal continuous current Ith 10A AC/2.5A DC. Bulletin 800T units with 800T-XA contacts have ratings as follows: Max. Opertnl. Volts Ue Utilization Category IEC NEMA A600 Rated Operational Currents Volts Ue 120 to 600 72 to 120 24 to 72 28 to 600 24 to 28 ➌ Make Break 7200VA 720VA 60A 720VA 60A 10A 69VA 2.5A AC 600 AC-15 DC 600 DC-13 Q600 ! Performance Data: see publication A113, page Important-2. ➋ Operating temperatures below freezing are based on the absence of moisture and liquids. ➌ For applications below 24V/24mA, PenTUFF contacts are recommended. 6-17 Emergency Stop Devices Push Buttons 800 E-Stops Product Selection—30.5mm Emergency Stop Operators — 2-Position Red Non Illuminated 2-Position Push-Pull 2-Position Push-Pull/Twist Operator Position Contacts Maintained Out Maintained In Enclosure Protection Type 4 & 13 Release Push-Pull Catalogue Number 800T -FX6D4 800T -FXT6D4 N.C.L.B. ! Closed Open Push-Pull/Twist Type 4, 4X & 13 Push-Pull N.O. Open Closed N.C.L.B. ! Closed Open Type 4 & 13 800T -FXT6A1 Push-Pull/Twist Type 4, 4X & 13 N.C.L.B.! Closed Open N.C.L.B.! Closed Open Push-Pull Type 4 & 13 800T -FXT6A5 Push-Pull/Twist Type 4, 4X & 13 Push-Pull S.M.C.B. ➊➋ Closed Open Type 4 & 13 800TC-FXT6D4S Push-Pull/Twist Type 4, 4X & 13 Push-Pull N.O. Open Closed S.M.C.B. ➊➋ Closed Open Type 4 & 13 800TC-FXT6A1S Push-Pull/Twist Type 4, 4X & 13 Push-Pull S.M.C.B. Closed Open S.M.C.B.➊➋ Closed Open Type 4 & 13 800TC-FXT6A5S Push-Pull/Twist Type 4, 4X & 13 Note: Emergency stop push buttons are compliant with EN-418 and IEC 60947-5-5 Standards when using N.C.L.B. contact blocks. ➊ Normally closed late break contact. When button is pushed from the OUT to IN position, the mechanical detent action of the operator occurs before electrical contacts change state. When the button is pulled from the IN to the OUT position, the electrical contacts change state before the mechanical detent occurs. ➋ The Self-Monitoring Contact Block (S.M.C.B.) is composed of a N.C.L.B. contact wired in series with a N.O. monitoring contact. The N.O. monitoring contact automatically closes when the S.M.C.B. is properly installed onto the E-Stop operator. If the S.M.C.B. is separated from the E-Stop operator, the N.O. monitoring contact will automatically open. 800H-FRXT6D4 800T -FX6A1 800H-FRXT6A1 800T -FX6A5 800H-FRXT6A5 800TC-FX6D4S 800HC-FRXT6D4S 800TC-FX6A1S 800HC-FRXT6A1S 800TC-FX6A5S 800HC-FRXT6A5S 6-18 Emergency Stop Devices Push Buttons 800 E-Stops Product Selection—30.5mm 2-Position Red Illuminated, Push-Pull and Push-Pull/Twist Release Units Illuminated 2-Position Push-Pull Illuminated 2-Position Push-Pull/Twist Operator Position Contacts N.O. N.C.L.B.➊➋ Maintained Maintained Out In Type Lamp Volts 120 AC/DC Enclosure Protection Type 4 & 13 Type 4, 4X & 13 Type 4 & 13 Type 4, 4X & 13 Type 4 & 13 Release Push-Pull Push-Pull/ Twist Push-Pull Catalogue Number 800T -FXQ10RA1 800T -FXTQ10RA1 800H-FRXTQ10RA1 800T -FXQ24RA1 800T -FXTQ24RA1 800H-FRXTQ24RA1 800T -FXQH10RA1 800T -FXTQH10RA1 800H-FRXTQH10RA1 800T -FXQH24RA1 800T -FXTQH24RA1 800H-FRXTQH24RA1 800T -FXP16RA1 800T -FXTP16RA1 800H-FRXTP16RA1 800T -FXP26RA1 Incan-descent 24 AC/DC Full Voltage 120 AC LED 24 AC/DC Open Closed Closed Open 120 AC Incan-descent 240 AC Transformer 120 AC LED 240 AC Push-Pull/ Twist Push-Pull Push-Pull/ Twist Push-Pull Type 4, 4X & 13 Type 4 & 13 Type 4, 4X & 13 Type 4 & 13 Type 4, 4X & 13 Type 4 & 13 Type 4, 4X & 13 Type 4 & 13 Type 4, 4X & 13 Type 4 & 13 Type 4, 4X & 13 Push-Pull/ Twist Push-Pull Push-Pull/ Twist Push-Pull Push-Pull/ Twist Push-Pull Push-Pull/ Twist Push-Pull Push-Pull/ Twist 800T -FXTP26RA1 800H-FRXTP26RA1 800T -FXPH16RA1 800T -FXTPH16RA1 800H-FRXTPH16RA1 800T -FXPH26RA1 800T -FXTPH26RA1 800H-FRXTPH26RA1 Note: A jumbo or large legend plate is recommended if space allows. Note: Emergency stop push buttons are compliant with EN-418 and IEC 60947-5-5 Standards when using N.C.L.B. contact blocks. ➊ Normally closed late break contact. When button is pushed from the OUT to IN position, the mechanical detent action of the operator occurs before electrical contacts change state. When the button is pulled from the IN to the OUT position, the electrical contacts change state before the mechanical detent occurs. ➋ Consult your local Allen-Bradley sales office for availability of illuminated E-Stops with Self Monitoring Contact Blocks (S.M.C.B.s). 6-19 Emergency Stop Devices Push Buttons 800 E-Stops Accessories Type Enclosure Plastic (IP66, NEMA 4/4X/13 Base Mount For use with 22.5mm Push Buttons Style 1 Hole 2 Hole Yellow 3 Hole 5 Hole 800E-3PY 800E-5PY Colour Catalogue Number 800E-1PY 800E-2PY Square Legend Plate For 800E Buttons Aluminum Aluminum, Blank 800E-19AE100 40mm Circular Legend Plate For 800 E Buttons 60mm Circular Legend Plate 800E-15YE112 Yellow, Emergency Stop 800E-16YE112 800T -X646 800T -X646EM Yellow, Blank For 800T Buttons Circular Legend Plate For 800H Yellow, Emergency Stop Yellow, Blank 800H-W690 6-20