RK1191124001

Metal Shaft Potentiometer 11mm Size Metal Shaft Reflow Type RK119 Series 1.5mm-travel push-on switch achieved in a low-profile of only 5mm height. Typical Specifications Items Total resistance tolerance Maximum operating voltage Total rotational angle Rotational torque Operating life Operating temperature range Specifications ±20％ 50V AC, 10V DC 300 ＋10° −5° 7.5±3.5mN m ・ 15,000cycles − 40℃ to ＋85℃ Rotary Potentiometers Slide Potentiometers Product Line Single-shaft without switch type Number of resistor elements Mounting direction Shaft type Length of the shaft （mm） Total resistance （kΩ） Resistance taper Switch travel （mm） Without Single-unit Vertical type Flat 20 10 1B 0.5 1.5 300 Metal Shaft Minimum order unit （pcs.） Insulated Shaft Knob Operating Products No. RK1191110001 RK1191114001 RK1191124001 Drawing No. 1 2 3 Note Products other than those listed in above products are also available. Please contact us for details. 343 Metal Shaft Potentiometer 11mm Size Metal Shaft Reflow Type RK119 Series Dimensions No. Photo Single-shaft, single-unit RK1191110001 Style Unit:mm PC board mounting hole dimensions （Viewed from mounting side） 13 12.5 7.5 6.3 5 Rotary Potentiometers Slide Potentiometers Dummy 2-2.4 2-2.4 2-2.4 1.9 4.5 4 3-2.1 8.5 8.2 14.2 18 3 1 ¿1.5 R1 1.2 ¿7.85 C1 123 15 Shaft shown in full C.C.W position 1.55 3-1.2 2-R0.8 4.5 ¿6 4 9 16.5 PC board mounting details Slant line area: solder land Black area: do not solder and wire       for electrical contact 13 Metal Shaft Insulated Shaft Knob Operating Single-shaft, single-unit with push-on switch travel 0.5mm RK1191114001 Mounting surface Switch Switch travel 20 (15) 5 5 7 0.5 11.7 8.1 ¿2.05 hole 2-1.3 4 12.6 12.5 7.5 6.3 5 45 ¿2 5.5 19 10 45 14.2 18 ¿1.5 2 R1 1.2 ¿7.85 C1 123 15 Shaft shown in full C.C.W position 4 5 1.55 3-1.2 2-R0.8 3 9 16.5 PC board Mounting detail A slant line part:The solder land Black part:Do not solder and wiring for electrical contact 13 Single-shaft, single unit with push-on switch travel 1.5mm RK1191124001 Mounting surface Switch Switch travel 20 (15) 5 5 7 12.5 7.5 1.5 11.7 8.1 ø2.05 hole 2-1.3 4 6.3 5 60û 12.6 3 4.5 ¿6 ¿1.5 1.2 R1 ¿7.85 3 123 15 C1 14.2 18 5.5 ¿2 19 10 45 45 1.55 3-1.2 2-R0.8 123 Shaft shown in full C.C.W position 4 5 9 16.5 PC board Mounting detail A slant line part:The solder land Black part:Do not solder and wiring for electrical contact 344 1.9 4.5 3-2.1 4 123 4.5 ¿6 8.5 8.2 60û 4.5 3-2.1 1 23 8.5 8.2 Mounting Dummy surface terminal ¿2 20 5 (15) 57 19 12.6 10 5.5 4 60¡ 11.7 8.1 Dummy terminal ¿2.05 hole 2-1.3 Metal Shaft Potentiometer 11mm Size Metal Shaft Reflow Type RK119 Series Product Varieties In addition to the recommended products, the following specifications can also be accommodated. Total Resistance Variety Total resistance kΩ） （ 10 20 50 Rotary Potentiometers Slide Potentiometers Resistance Taper Resistance taper 15A 1B 3B Detent and Attached Switch Items Variety Single-shaft, Single-unit Detent Without Attached switches travel 0.5mm 1.5mm Dimensions of Shaft Flat type L1 LB R Unit:mm 60 û Metal Shaft Insulated Shaft Detail dimensions mm） （ L1 ¿6 4.5 ※LB 5 5 R 7 10 Knob Operating ¿7.85 C1 Shaft shown in full CCW position. （15） （20） Notes 1. ※LB does not support M7(with Screws). 2. marked are specifications recommended by ALPS. Specification for Switch Mechanical Characteristics Type Travel （mm） 0.5±0.3 SPST 1.5±0.5 Pole-position Rating Changeover torque （Operating force） 5±2N 4±2N Momentary push type DC 5V 0.1A （1mA 5V DC min.rating） Electrical Characteristics Type Momentary push type Contact resistance 100mΩfor initial period, 200mΩafter operating life Insulation resistance 100MΩ min. Measured with a 250V DC megger. Voltage proof 300V AC 1 minute min. Durability Travel 0.5mm The switch under a rated resistive load shall be subjected to a total of 100,000 cycles of operation at a speed of 600 to 1,000 cycles per hour. The contact resistance after testing should not exceed 200mΩ. The switch under a rated resistive load shall be subjected to a total of 20,000 cycles of operation at a speed of 600 to 1,000 cycles per hour. The contact resistance after testing should not exceed 200mΩ. Operating life under load Travel 1.5mm Note The operating current should be 10mA or greater. Refer to P.346, 502 for resistance taper. 345 11mm Size Metal Shaft Low-profile Potentiometer Orders other than for recommended products When ordering product varieties that are not listed in the Product Line, please specify by referring to the below example. Rotary Potentiometers Slide Potentiometers Sample Part Number RK1191110 Switch Travel（mm） Code 1 2 Switch 0.5 1.5 F15 C0 B103 ＊For "without switch" type, select 1. Switch Metal Shaft Insulated Shaft Knob Operating Code 0 4 Switch Without switch With push-on switch Length of the shaft L1） mm） （（ Code 15 20 Length of the shaft 15 20 Detent Code C0 Detent Without Resistance taper J G 100 (%) Output volt.across term.1-2 Input volt. across term. 1-3 Code A B V Resistance taper 15A 1B 3B 100 90 80 70 60 50 40 30 vo l.c on B tro (1 l)( B) 3B ) B:For tone & general V:For vol. 20 10 0 10 A) 15 A( V( 20 30 40 50 60 70 80 90 100 Term."1" Rotation travel (%) J Term."3" Total resistance Code 103 203 503 Total resistance kΩ） （ 10 20 50 Note marked are specifications recommended by ALPS. 346 Metal Shaft Potentiometers List of Varieties Type Number of drive shafts Model 9mm size metal shaft snap-in Single-shaft RK09L1 RK0971 RK0981 9mm size metal shaft multi-ganged Dual-shaft RK0972 11mm size metal 11mm size metal 16mm size metal shaft low-profile shaft reflow shaft Single-shaft RK117111 RK119 RK1631□1 RK1631□A Rotary Potentiometers Slide Potentiometers Photo Fixing method of bushing The bushing can be screwed down Terminal mounting Attached switch Gang error applicable to Dual-unit parts for audio volume control purposes Solder heat resistance Manual soldering Dip soldering Reflow soldering −10℃ to ＋70℃ Horizontal type Vertical type Without Bushing screw clamp Horizontal type Rotary switch ※1 Push-on push-off switch※1 Momentary push switch※1 Bushing guide type Vertical type Momentary push switch Bushing screw clamp Horizontal type Without −40dB to 0dB 3dB max. 350℃ max. 3s max. 260±5℃, 5±1s Please see P.347 −20℃ to ＋70℃ 350±10℃ 3 ＋1 s 0 −40dB to 0dB 3dB max. 350℃ max. 3s max. Motor terminal : 350$max 2s max. Metal Shaft −30℃ to ＋70℃ −40℃ to ＋85℃ −10℃ to ＋70℃ 0.05W Operating emperature range Rated power Residual resistance Maximum attenuation （Volume control） Insulation resistance Voltage proof Mechanical Environmental performance performance Stopper strength Push-pull strength Vibration Cold Dry heat Damp heat Page ページ Insulated Shaft Knob Operating R≦10kΩ 10kΩ＜ R＜50kΩ 50kΩ≦ R 20Ωmax. 30Ωmax. Nominal total resistance of 0.1% or less 5kΩ≦R＜ 10kΩ 10kΩ≦R＜ 50kΩ 50kΩ≦R＜100kΩ 100kΩ≦R 70dB min. 80dB min. 90dB min. 100dB min. R≦10kΩ 50Ωmax. R≦10kΩ 20Ωmax. 10kΩ＜R≦50kΩ 80Ωmax. 10kΩ＜R≦50kΩ 30max. 50kΩ＜R 50kΩ＜R Nominal total resistance of 0.2% or less Nominal total resistance of 0.1% or less ● Metal Shaft Potentiometers Attached Parts …………………………………………………………………………363 ● Metal Shaft Potentiometers Cautions ……………………………………………………………………………364, 365 Notes 1. ※1. For the switch attached, the single-shaft or inner shaft of the dual-shaft type can be chosen. 2. The operating temperature range for automotive applications can be raised upon request. Please contact us for requirements of this kind. Electrical performance 100MΩ min. 250V DC 300V AC for 1minute 0.5N m With push-lock mechanism type: 0.4N·m） ・（ 80N max. 100N max. 0.5N m ・ 100MΩ min. 500V DC 500V AC for 1minute 0.9N m ・ 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z and for 2 hours respectively −20℃±2℃ for 96h −30±2℃ for 96h 70±2℃ for 96h 40±2℃, 90 to 95％RH for 96h 323 327 339 −40±2℃ for 240h 85±2℃ for 240h −20±2 for 96h 70±2℃ for 96h 60±2℃, 90 to 95％RH for 240h 343 40±2℃, 90 to 95％RH for 96h 348 Push-on Switch Specifications Items Contact arrangement Travel mm） （ Operating force（N） Rating Contact resistance Operating life 0.5 4 ＋4 −2 RK097 RK117 Single pole and single throw（Push on） 1.5 5±2 0.5 6±3 3A 16V DC 1.5 5±2 RK119 0.5±0.3 1.5±0.5 4±2 0.5A 12V DC 0.1A 5V DC (1mA 5V DC min.ratings) 100mΩfor initial period;200mΩafter operating life 10,000 times 20,000 times 10,000 times 20,000 times min. min. min. min. 100,000 times min. 20,000 times min. 321 11mm Size Metal Shaft Reflow type Potentiometers Soldering Conditions Example of Reflow Soldering Condition 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2φ CA K） CC T） soldering portion copper foil surface） A heat resisting tape （ or （ at （ . should be used for fixed measurement. 3. Temperature profile Rotary Potentiometers Slide Potentiometers 300 Temperature (ûC ) A B 200 C D 100 Time (s) Pre-heating E max. F max. G max. 40 max. Metal Shaft Insulated Shaft Knob Operating Room temperature Series Reflow type） （ A （℃） 3s max. B （℃） C （℃） D （℃） E （s） F （s） G （s） RK119 260 230 180 150 120 240 Notes 1. The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the PC board's material, size, thickness, etc. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. 347