SKHWARA010

TACT SwitchTM 6mm Square Dust-proof (Snap-in Type) SKHW Series Suitable for various electronic devices with unique dust-proof structure and sharp operation feeling. Detector Push Slide Rotary Encoders Power Dual-in-line Package Type Stem Minimum order height unit pcs.） （ h=4.3mm Product Line Product No. SKHWALA010 SKHWARA010 SKHWAPA010 SKHWAQA010 Operating Operating Travel Rating Rating Operating life Initial contact Stem color direction （mm）（max.） （min.） （5mA 5V DC） resistance force 1.57N 2.55N Vertical 1.57N 2.55N 0.3 50mA 12V DC 10BA 1V DC 1,000,000cycles 500,000cycles 1,000,000cycles 500,000cycles 100mΩ max. Dark gray Red 1,000 Dark gray h=5mm Red TACT SwitchTM CustomProducts Dimensions Style Unit:mm PC board mounting hole dimensions （Viewed from switch mounting face） h Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type H6 1 2 4.3 5 4-ø1 holes 4.5 Radial Type 3 ø2.7 4 4.5 Stem 6.5 3.6 6.5 h 3.5 0.7 Circuit Diagram Note Please use 1.6mm thick PC boards. 1 3 2 4 Refer to P.306 for soldering conditions. 259 TACT SwitchTM List of Varieties Sharp Feeling Type Series SKHR SKHL SKHH SKHW SKRD SKQJ SKHL SKHH SKQJ SKHJ SKQB Detector Push Type Features Operating direction Vertical Horizontal W Dimensions （mm） □4.5 6 □6 3.5 3.8 4.3 7.15 7.4 5 ● ― ● ― ● Dust–proof Horizontal type type ● ― ● 6.2 □6.6 7.22 4.3 7.4 7.85 7.3 8.5 5 Snap–in ― ● ― ● 7.3 Horizontal type ― ● 7.5 □8 □10 ● With LED ● ― Water– proof ● Photo Slide Rotary Encoders Power Dual-in-line Package Type TACT SwitchTM D H 1N CustomProducts Operation force coverage 5N Ground terminal Operating temperature range Electrical performance Durability Insulation resistance Voltage proof Vibration Lifetime Cold Dry heat Damp heat Page 252 253 255 259 ― ● ― ● ● ― ｰ20℃ to ＋70℃ SKHJ/HL Vertical Type）/QJ （ ｰ30℃ to ＋85℃ 100MΩ min. 100V DC 250V AC for 1min. 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2hours respectively Shall be in accordance with individual specifications. ｰ30±2℃ for 96h 80±2℃ for 96h 60±2℃, 90 to 95%RH for 96h 260 261 253 255 261 263 265 Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type ● TACT SwitchTM Soldering Conditions ………………………………………………………………………………………306 ● TACT SwitchTM Cautions ………………………………………………………………………………………………………307 ● Product Line of Knob for TACT SwitchTM ……………………………………………………………………………………308 Note The automotive operating temperature range to be individually discussed upon request. Environmental performance W：Width. The most outer dimension excluding terminal portion. D ：Depth. The most outer dimension excluding terminal portion. H ：Height. The minimum dimension if there are variances. 247 TACT SwitchTM Soldering Conditions Condition for Reflow Available for Surface Mount Type. 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2φ CA K） CC T） solder joints copper foil surface） A heat resistive tape （ or （ at （ . Detector Push Slide Rotary Encoders Power should be used to fix thermocouple. 3. Temperature profile Temperature (˚C ) 260˚C max. 3 sec max. 180 150 Time 230˚C Dual-in-line Package Type TACT SwitchTM 120 sec max. pre-heating ） （ 3 to 4min. 40s max. CustomProducts Time inside soldering equipment Note 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Conditions for Auto-dip Available for Snap-in Type and Radial Type （Except SKHJ, SKHL, SKQJ, SKQK, SKEG series） Items Flux built-up Condition Mounting surface should not be exposed to fluk Ambient temperature of the soldered surface of PC board. 100℃ max. 60s max. 260℃ max. 5s max. 2times max. Manual Soldering（Except SKRT Series） Items Soldering temperature Duration of soldering Capacity of soldering iron Condition 350℃max. 3s max. 60W max. Preheating temperature Preheating time Soldering temperature Duration of immersion Number of soldering Notes 1. 2. 3. 4. 5. Consult with us for availability of TACT SwitchTM washing. Prevent flux penetration from the top side of the TACT SwitchTM. Switch terminals and a PC board should not be coated with flux prior to soldering. The second soldering should be done after the switch is stable with normal temperature. Use the flux with a specific gravity of min 0.81. （EC-19S-8 by TAMURA Corporation, or equivalents.） 306