SKRGAFD010

TACT SwitchTM 6.2mm Diameter Round Terminal (Radial Type) SKRG Series Round-terminal vertical type with excellent PC board mounting performance. Detector Push Slide Rotary Encoders Product Line Power Dual-in-line Package Type TACT SwitchTM CustomProducts Product No. Operating Operating Travel Rating Rating Operating life Initial contact force direction （mm）（max.）（min.）（5mA 5V DC） resistance SKRGAAD010 SKRGABD010 SKRGACD010 SKRGADD010 SKRGAED010 SKRGAFD010 SKRGALD010 SKRGAMD010 SKRGAND010 SKRGAQD010 Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type !!" !!" Stem color Black Stem height Minimum order unit （pcs.） 1.27N 500,000cycles 1.57N 2.55N 1.27N 500,000cycles 1.57N 2.55N Vertical 1.27N 1.57N 2.55N 1.27N 500,000cycles 1.57N 2.55N 200,000cycles 200,000cycles 0.25 50mA 12V DC 10BA 1V DC 200,000cycles 500,000cycles 500mΩ max. 200,000cycles White h=4.3mm Gray Black White Gray 2,000 Black White Gray Black White h=9.5mm Gray h=7mm h=5mm SKRGARD010 SKRGASD010 Specification of Radial Taping Package (Taping Packaging for Auto-insertion) Box Size SKRGAA to AF !# Unit:mm SKRGAL to AS !# Number of packages pcs.） （ 1 box 1 case /Japan 1 case /export packing 2,000 20,000 20,000 "! "& Dimensions Style 12.7 Stem Unit:mm PC board mounting hole dimensions （Viewed from switch mounting face） h 4.3 5 7 9.5 18 ø6.2 øA 1 2 ø0.5 A 3.4 3.4 3.2 2.9 5 2 -ø 1h o le s 3.6 h 9 18 5 ø4 12.7 Circuit Diagram 1 2 Notes 1. Please use 1.6mm thick PC boards. 2. Please place purchase orders for taping products per minimum order unit (1 reel or a case). Refer to P.306 for soldering conditions. 292 TACT SwitchTM List of Varieties Sharp Feeling Type Series Detector Push Type Slide Features Rotary Encoders Power W Dual-in-line Package Type TACT SwitchTM H CustomProducts Operation force coverage 5N Ground terminal Operating temperature range Electrical performance Durability Insulation resistance Voltage proof Vibration Lifetime Cold Dry heat Damp heat Page 289 290 291 ― ● ● ● ｰ20℃ to ＋70℃ SKRV/QK ｰ30℃ to ＋85℃ 100MΩ min. 100V DC 250V AC for 1min. SKSC/RE/RV/RH : 100V AC for 1min. 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2hours respectively Shall be in accordance with individual specifications. ｰ30±2℃ for 96h 80±2℃ for 96h 60±2℃, 90 to 95%RH for 96h 480 481 482 292 294 293 295 ― 1.25 1.5 3.3 4 5 7.1 4.3 5 7.1 13 3.5 3.9 3.55 4.5 6.45 6.4 7.35 □10 V6.2 □6.6 6.85 7.5 7.3 V9 Low–profile Horizontal type ― ● ● ● Surface mount Horizontal type 4–direction switch＋push switch ● ● ● ― Round terminal type ● ― ● Radial Round terminal Water–proof Horizontal type ― ● ● ― SKSC SKRE SKRT SKRV SKRH SKQU SKRG SKQK SKQN SKRC Photo Dimensions （mm） Operating direction Vertical Horizontal D 1N See the relevant pages for respective product descriptions Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type ● TACT SwitchTM Soldering Conditions ………………………………………………………………………………………306 ● TACT SwitchTM Cautions ………………………………………………………………………………………………………307 ● Product Line of Knob for TACT SwitchTM ……………………………………………………………………………………308 Note The automotive operating temperature range to be individually discussed upon request. Environmental performance W：Width. The most outer dimension excluding terminal portion. D ：Depth. The most outer dimension excluding terminal portion. H ：Height. The minimum dimension if there are variances. 250 TACT SwitchTM Soldering Conditions Condition for Reflow Available for Surface Mount Type. 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2φ CA K） CC T） solder joints copper foil surface） A heat resistive tape （ or （ at （ . Detector Push Slide Rotary Encoders Power should be used to fix thermocouple. 3. Temperature profile Temperature (˚C ) 260˚C max. 3 sec max. 180 150 Time 230˚C Dual-in-line Package Type TACT SwitchTM 120 sec max. pre-heating ） （ 3 to 4min. 40s max. CustomProducts Time inside soldering equipment Note 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Conditions for Auto-dip Available for Snap-in Type and Radial Type （Except SKHJ, SKHL, SKQJ, SKQK, SKEG series） Items Flux built-up Condition Mounting surface should not be exposed to fluk Ambient temperature of the soldered surface of PC board. 100℃ max. 60s max. 260℃ max. 5s max. 2times max. Manual Soldering（Except SKRT Series） Items Soldering temperature Duration of soldering Capacity of soldering iron Condition 350℃max. 3s max. 60W max. Preheating temperature Preheating time Soldering temperature Duration of immersion Number of soldering Notes 1. 2. 3. 4. 5. Consult with us for availability of TACT SwitchTM washing. Prevent flux penetration from the top side of the TACT SwitchTM. Switch terminals and a PC board should not be coated with flux prior to soldering. The second soldering should be done after the switch is stable with normal temperature. Use the flux with a specific gravity of min 0.81. （EC-19S-8 by TAMURA Corporation, or equivalents.） 306