SPVL110102

SPVL Low-profile Tri-directional Operation Type Detector Flexible and thin 1mm height detector switch with a large operational range of 180 degrees ■ Typical Specifications Items Specifications Rating（max.）（ / min.） （Resistive load） Contact resistance （Initial / After operating life） Slide 1mA 5V DC / 50μA 3V DC 2Ωmax. / 5Ωmax. Operating force 0.35N max. Push Without load 50,000cycles Operating life With load 50,000cycles（1mA 5V DC） Rotary Product Line Positions Terminal type 1 1 For PC board （Reflow） Minimum order unit（pcs.） Location lug With Without Japan Export 5,000 20,000 Product No. Power Poles SPVL110102 SPVL120101 Unit:mm 1 reel 1 case /Japan 1 case /export packing Tape width （mm） Export package measurements （mm） 5,000 10,000 20,000 16 417×409×139 Number of packages（pcs.） Reel size Dual-in-line Package Type Packing Specifications Taping Generalpurpose Type Unit:mm Style PC board mounting hole and land dimensions （Viewed from direction A） Terminal Layout （Viewed from Direction A） 1 1 4 2 3 1 ø1 1.9 ho 3 le 0.8 1.5 .1 Circuit Diagram 1.25 4) 0. (C 2.7 2.8 1.6 2- Fast Switching Type With boss Water-proof Type Dimensions 3.9 1 2 (Common) 4 3 (Dummy) Notes Dimensions drawing is for type with location lugs. Refer to P.73 for soldering conditions. 33 Detector Switches List of Varieties General-purpose Type Detector Series SPPW8 SSCQ SSCM SPVL SPPB One-way Two-way Two-direction type Two-way Three-way One-way Two-way 5 3.8 5 5.55 6.3 3.6 4 6.6 3 0.9 1.5 1 4.9 Slide Photo Operation type Push W Dimensions （mm） D H 4 Rotary Operating temperature range Automotive use −10℃ to ＋60℃ −40℃ to ＋85℃ Power Dual-in-line Package Type — — — Poles / Positions 1/1 1 / Two-direction type： 2-position each side 1/2 Rating（max.） （Resistive load） 0.1A 30V DC Rating（min.） （Resistive load） 100μA 3V DC ● ● Life cycle (availability) Durability Generalpurpose Type Water-proof Type Electrical performance Fast Switching Type Mechanical performance Environmental performance 1/1 1mA 5V DC 0.1A 30V DC 50μA 3V DC Operating life without load 100,000cycles 2Ω max. 50,000cycles 5Ω max. 50,000cycles 2Ω max. Operating life with load Rating（max.） （Resistive load） 100,000cycles 2Ω max. 50,000cycles 5Ω max. 50,000cycles 2Ω max. Initial contact resistance 1Ω max. 2Ω max. 1Ω max. Insulation resistance 100MΩ min. 100V DC Voltage proof 100V AC for 1 minute Terminal strength 3N for 1minute Actuator strength 10N 0.5N for 1minute 1N 1N for 1minute 3N for 1minute 5N 10N 2N Cold −20℃ 96h −40℃ 500h Dry heat 85℃ 96h 85℃ 500h Damp heat 40℃, 90 to 95%RH 96h 60℃, 90 to 95%RH 500h Operation force 0.3N max. Page 29 0.35N max. 31 32 33 34 Detector Switches Soldering Conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 73 Detector Switches Cautions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 74 Note ● Indicates applicability to all products in the series. 12 Detector Switches Soldering Conditions 1. 2. 　 3. Heating method: Double heating method with infrared heater. Temperature measurement: Thermocouple φ0.1 to 0.2 CA（K）or CC（T）at soldering portion（copper foil surface）. A heat resisting tape should be used for fixed measurement. Temperature profile Detector Example of Reflow Soldering Condition Slide A max. B 200 Push D E 100 Rotary Temperature (˚C ) 300 Room temperature Time (s) A（℃）3s max. SPPB B（℃） C（s） D（℃） E（℃） F（s） 180 150 120 40 250 SPPW8 C Dual-in-line Package Type Series（Reflow type） Power Pre-heating F max. 35 SPVE SPVL SPVN 230 SPVR 40 260 Water-proof Type SPVS Generalpurpose Type SPVM SPVT SSCM SPVQC, SPVQE Fast Switching Type SSCQ 250 Notes 1. The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, surface depending on the PC board's material, size, thickness, etc. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Reference for Hand Soldering Series Soldering temperature Reference for Dip Soldering Soldering time (For PC board terminal types) Items Series SPVS, SPVN, SPVT, SPVM, SPVR, SPVE, SPPW8,SSCQ, SSCM, SPVL, SSCT, SPVQC, SPVQE 350±5℃ SPVQ1, SPVQ3, SPVQ6, SPVQ7, SPVQ8, SPVQ9, SSCN, SPVQA 300±10℃ 3 +1 / 0s SPPB（Reflow） 300±5℃ 5s max. SSCF, SPPB（For Lead, Dip） 350±10℃ 3 +1 / 0s 3s max. Preheating temperature Preheating time Dip soldering Soldering temperature SSCT, SPVQ1, SPVQ3, SPVQ6, SPVQ7, SPVQ8, 100±10℃ 60s max. 260±5℃ SPVQ9, SPVQA SPPW8, SPPB SSCF 100 ℃ max. 60s max. 255±5℃ ー 260±5℃ Duration of immersion 5±1s 5±1s 5±1s 73