SRGP400200

Hollow Shaft Type Devices Low-profile and Hollow Shaft Surface Mount Type SRGP40 Series Surface mount encoder with 1.55mm height V9.23mm contribute in space saving Typical Specifications Items Rating max.） min.） （ （ / （Resistive load） Output voltage Without resistor With resistor Specifications 1mA 5V DC/50BA 3V DC 1V max. at 1mA 5V DC （Resistive load） 100,000cycles 100,000cycles Hollow Shaft Type Devices Operating life Product Line Detent torque （mN m） ・ 2±1 3.5±1 Number of detent 24 Number of pulse 12 Soldering Reflow Minimum order unit （pcs.） 3,200 Product No. SRGP400100 SRGP400200 Taping Specification (Taping Packeging) Reel Size Unit:mm Number of packages pcs.） （ 1 reel 1 case／ Japan 1 case／export packing Tape width （mm） 800 ¿380 33.4 1,600 3,200 32 Encoder Type Potentiometer Type Note Order products in N minimum order units（1 reel or 1 case） . Dimensions Style 17.5 9.7 8.9 2-2 Ground term. 12.5 Unit:mm Recommened patern for reflow （All tolerance shall be %0.05） 2 - 1.2 ø9 A .2 2 - 1.2 (0.2) 0.95 1.55 ø10.7 3 2.15 0.55 A 1 1 8.9 9.7 12.4 ø13.6 6 8.2 6-0.7 2.15 C 2 2.75 1.55 ø1 R1 0 9.85 2 2-ø1.5 19.1 14.4 12.5 1.15 7 0.15 10 0.5 A-A 12.8 2.2 Phase defference of code portion .6 ø1 (15$) 0.5 12 CCW Detent position ON OFF ON OFF 1 2 0.72 T1 T2 T T3 T4 T1, T3 = 1 / 4T ± 1 / 8T T2, T4 = Phase difference shall not be reverseed 2.75 (30$) 1.55 0.05 CW 451 Hollow Shaft Type Devices List of Varieties Type Series SRGP30 Hollow type 17mm size SRGP40 22mm size SRGP20 30mm size SRGPWJ Hollow Shaft Type Devices Photo Output Shaft types Operating direction Outline specifications Dimensions （mm） Soldering Number of pulse/ Number of detent Push switch （Travel mm） Optional functions Changeover angle W D H Manual soldering Dip soldering Reflow soldering Maximum operating current Resistive load） （ Please see P.198 –10℃ to ＋60℃ 18.5 2.3 350±5℃, 3s max. 20° 15° 9/18 12/24 Incremental Hollow shaft Vertical 10/20 Without 16/16 16/32 18° 23.6 22.5° 31.8 32 4.5 17.5 18.25 1.55 350±10℃, 3 ＋1 0 23 s max. 350±10℃, 3 ＋1 s 0 260±5℃, 5±1s Encoder Type –40℃ to ＋85℃ 1V max. at 5V DC,1mA （resistive load） Potentiometer Type Note F The operating temperature range for automotive applications can be raised upon request. Please contact us for requirements of this kind. Electrical performance Mechanical performance Environmental performance Output wave Measuring 5K½ circuit Measuring terminal 5V Insulation resistance Voltage proof Rotational torque Terminal strength Actuator strength Rotational direction 20N 5±2.5mN･m 100MΩ min. 100V DC 100V AC for 1minute 2±1mN･m 7±3mN･m 3.5±1mN･m 6.5±4mN･m 5N for 1minute 40N 13±4mN･m Push direction 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2 hours respectively –40±2℃ for 96h –20±2℃ for 96h 85±2℃ for 96h 40±2℃, 90 to 95%RH for 96h 450 451 452 Vibration Cold Dry heat Damp heat Page 447 Hollow Shaft Type Devices Soldering Conditions Example of Reflow Soldering Condition Hollow Shaft Type Devices 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2φ CA K） CC T） soldering portion copper foil surface） A heat resisting tape （ or （ at （ . should be used for fixed measurement. 3. Temperature profile 300 A max. B Temperature (ûC ) 200 D E 100 Time (s) Pre-heating F max. Room temperature C Series Reflow type） （ SRGP30 Encoder Type Potentiometer Type SRGP40 A （℃） Max 240 B （℃） C s） （ 20 D （℃） 150 E （℃） （ F s） 230 260 40 180 150 120 Notes 1. The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the PC board's material, size, thickness, etc. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. You are requested to verify the soldering conditions thoroughly beforehand. 454