SSAG330200

2019/2/21 SSAG Series - Basic information Recoil Type for Single-side and Both-sides SSAG Series Travel 1.5mm Actuator directions Horizontal Poles 1 Positions 3 Operating force 1N (Recoil side) Changeover timing Not specified Soldering Reflow Operation Double-side recoil Shape of frame leg For PC board insert Location lug With Operating temperature range -10℃ to +60℃ Rating (max.)/(min.) (Resistive load) 10mA 5V DC/50µA 3V DC Electrical performance Contact resistance (Initial performance/After lifetime) 200mΩ max./500mΩ max. Insulation resistance 100MΩ min. 100V DC Voltage proof 100V AC for 1 minute Terminal strength 3N for 1 minute Mechanical performance Actuator strength Durability Environmental performance Operating direction 10N Pulling direction 10N Operating life without load 100,000 cycles 500mΩ max. Operating life with load (at max. rated load) 100,000 cycles 500mΩ max. Cold -40℃ 96h Dry heat 85℃ 96h Damp heat 40℃, 90 to 95%RH 96h Minimum order unit (pcs.) Japan 4,000 Export 16,000   About Cookies on this site： This site uses cookies to improve your online experience. By continuing to use this site without changing Dimensions your cookie preferences, we will assume that you are agreeing to our use of cookies. For more information, visit our Terms of Use. https://www.alps.com/prod/info/E/HTML/Switch/Slide/SSAG/SSAG330200.html Accept 1/4 2019/2/21 SSAG Series - Basic information Land Dimensions About Cookies on this site： This site uses cookies to improve your online experience. By continuing to use this site without changing   Viewed directionwe A will in the dimensions. your cookie from preferences, assume that you are agreeing to our use of cookies. For more information, visit our Terms of Use. Accept Circuit Diagram https://www.alps.com/prod/info/E/HTML/Switch/Slide/SSAG/SSAG330200.html 2/4 2019/2/21 SSAG Series - Basic information Packing Specifications Taping Number of packages (pcs.) 1 reel 4,000 1 case / Japan 8,000 1 case / export packing 16,000 Tape width (mm) 24 Export package measurements (mm) 428×413×172 Soldering Conditions Example of Reflow Soldering Condition 1. Heating method Double heating method with infrared heater. 2. Temperature measurement Thermocouple 0.1 to 0.2 Φ CA (K) or CC (T) at soldering portion (copper foil surface). A heat resisting tape should be used for fixed measurement. 3. Temperature profile About Cookies on this site： This site uses cookies to improve your online experience. By continuing to use this site without changing your cookie preferences, we will assume that you are agreeing to our use of cookies. For more information, visit our Terms of Use. https://www.alps.com/prod/info/E/HTML/Switch/Slide/SSAG/SSAG330200.html Accept 3/4 2019/2/21 SSAG Series - Basic information A(℃) 3s max. B(℃) C(s) D(℃) E(℃) F(s) 260 230 40 180 150 120 (1) The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the PC board's material, size, thickness, etc. The above-stated conditions shall also apply to switch surface temperatures. (2) Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Reference for Hand Soldering Soldering temperature 350±5℃ Soldering time 3s max. Notes are common to this series/models. 1. This site catalog shows only outline specifications. When using the products, please obtain formal specifications for supply. 2. Please place purchase orders per minimum order unit (integer). About Cookies on this site： This site uses cookies to improve your online experience. By continuing to use this site without changing your cookie preferences, we will assume that you are agreeing to our use of cookies. For more information, visit our Terms of Use. https://www.alps.com/prod/info/E/HTML/Switch/Slide/SSAG/SSAG330200.html Accept 4/4