ASM3P2111A

March 2005 rev 1.3 Peak EMI Reducing Solution Features Generates an EMI optimized clocking signal at output. Input frequency – 25 MHz. Frequency outputs: o o o 60 MHz (unmodulated) 2 x 48 MHz (unmodulated) 66.6 MHz (modulated) -1.7% down spread ASM3P2111A The ASM3P2111A allows significant system cost savings by reducing the number of circuit board layers and shielding that are required to pass EMI regulations. The ASM3P2111A modulates the output of PLL in order to spread the bandwidth of a synthesized clock, thereby decreasing the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced by oscillators and most clock generators. Lowering EMI by increasing a signal’s bandwidth is called spread spectrum clock generation. Modulation rate: 30 KHz. Supply voltage range: 3.3V ± 0.3V. Available in 8-pin SOIC Package. Commercial and Industrial Temperature range. Applications ASM3P2111A is targeted towards EMI management for high speed digital applications such as PC peripheral devices, consumer electronics and embedded controller systems. Product Description The ASM3P2111A is a versatile spread spectrum frequency modulator. The ASM3P2111A reduces electromagnetic interference (EMI) at the clock source. Block Diagram VDD XIN /CLKIN XOUT 60 MHz Crystal Oscillator PLL1 48 MHz_1 48 MHz_2 48 MHz_1 PLL2 66.6 MHz Modulated VSS Alliance Semiconductor 2575 Augustine Drive • Santa Clara CA • Tel: 408-855-4900 • Fax: 408-855-4999 • www.alsc.com March 2005 rev 1.3 Pin Configuration ASM3P2111A XIN/ CLKIN XOUT VDD 60 MHz 1 2 3 4 8 7 VSS 66.6 MHz 48 MHz_1 48 MHz_2 ASM3P2111A 6 5 Pin Description Pin Name XIN / CLKIN XOUT VDD 60 MHz 48 MHz_2 48 MHz_1 66.6 MHz VSS Type I O P O O O O P Connection to crystal Connection to crystal Description Power supply for the analog and digital blocks(+3.3V) Clock output-1 60 MHz unmodulated Clock output-2 48 MHz_2 unmodulated Clock output-3 48 MHz_1 unmodulated Clock output-4 66.6 MHz modulated Ground to entire chip Peak Reducing EMI Solution 2 of 8 March 2005 rev 1.3 Absolute Maximum Ratings Symbol VDD, VIN TSTG TA Ts TJ TDV Storage temperature Operating temperature Max. Soldering Temperature (10 sec) Junction Temperature Static Discharge Voltage (As per JEDEC STD 22- A114-B) ASM3P2111A Parameter Voltage on any pin with respect to Ground Rating -0.5 to +7.0 -65 to +125 0 to 70 260 150 2 Unit V °C °C °C °C KV Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect device reliability. Operating Conditions Parameter Supply Voltage Crystal Resonator Frequency Output Driver Load Capacitance Symbol VDD FXIN CL Condition / Description 3.3V ± 0.3V Min 3 25 - Typ 3.3 - Max 3.6 15 Unit V MHz pF Peak Reducing EMI Solution 3 of 8 March 2005 rev 1.3 DC Electrical Characteristics Parameter Overall Supply Current, Dynamic Supply Current, Static All input pins High-Level Input Voltage Low-Level Input Voltage High-Level Input Current Low-Level Input Current (pull-up) High-Level Output Source Current Low-Level Output Sink Current Clock Outputs High-Level Output Source Current Low-Level Output Sink Current Output Impedance IOH IOL ZOH ZOL VO=2.5V VO=0.4V VO=0.5VDD; output driving high Vo=0.5VDD; output driving low -20 23 29 27 VIH VIL IIH IIL IxOH IxOL VDD=V (XIN) = 3.3V, VO=0.4V VDD=3.3V, V (XIN)=VO=2.5V VDD=3.3V VDD=3.3V 2.0 VSS-0.3 -1 -20 -36 3 3 IDD IDDL VDD=3.3V, FCLK=25MHz, CL=15pF VDD = 3.3V, Clock Input = 0 41 20 48 25 ASM3P2111A Symbol Conditions / Description Min Typ Max Unit 62 35 mA mA VDD+0.3 0.8 1 -80 - V V µA µA mA mA - mA mA Ω AC Electrical Characteristics Parameter Rise Time Fall Time Clock Duty Cycle Symbol tr tf Conditions/ Description VO = 0.8V to 2.0V; CL = 15pF VO = 2.0V to 0.8V; CL = 15pF Ratio of pulse width (as measured from rising edge to next falling edge at 2.5V) to one clock period Min 300 360 Typ 800 800 Max 900 900 Unit pS pS 45 - 55 % * CL = 15 pF, Input clock frequency = 25 MHz Peak Reducing EMI Solution 4 of 8 March 2005 rev 1.3 Crystal Oscillator Circuit ASM3P2111A Crystal R1 = 510Ω C1 = 27 pF C2 = 27 pF Crystal Specifications Fundamental AT cut parallel resonant crystal Nominal frequency Frequency tolerance Operating temperature range Storage temperature Load capacitance Shunt capacitance ESR 25 MHz ± 50 ppm or better at 25°C -25°C to +85°C -40°C to +85°C 18pF 7pF maximum 25 Ω Peak Reducing EMI Solution 5 of 8 March 2005 rev 1.3 Package Information 8-Pin SOIC Package ASM3P2111A E H D A2 A θ e B A 1 C L D Dimensions Symbol Min A1 A A2 B C D E e H L θ Inches Max 0.010 0.069 0.059 0.020 0.010 0.004 0.053 0.049 0.012 0.007 Millimeters Min Max 0.10 1.35 1.25 0.31 0.18 4.90 BSC 3.91 BSC 1.27 BSC 6.00 BSC 0.41 0° 1.27 8° 0.25 1.75 1.50 0.51 0.25 0.193 BSC 0.154 BSC 0.050 BSC 0.236 BSC 0.016 0° 0.050 8° Peak Reducing EMI Solution 6 of 8 March 2005 rev 1.3 Ordering Codes Part number ASM3P2111AF-08ST ASM3P2111AF-08SR ASM3I2111AF-08ST ASM3I2111AF-08SR ASM3P2111A MARKING 3P2111AF 3P2111AF 3I2111AF 3I2111AF Package Configuration 8-pin SOIC TUBE, Pb Free 8-pin SOIC TAPE & REEL, Pb Free 8-pin SOIC TUBE, Pb Free 8-pin SOIC TAPE & REEL, Pb Free Temperature Range Commercial Commercial Industrial Industrial Ordering Information ASM3P2111AF-08 SR OR - TSOT23 -6,T/R TT – TSSOP, TUBE TR - TSSOP, T/R VT – TVSOP, TUBE VR – TVSOP, T/R ST – SOIC, TUBE AR - SSOP, T/R AT – SSOP, TUBE SR - SOIC, T/R QR – QFN, T/R QT - QFN, TRAY BT - BGA, TRAY BR – BGA, T/R UR - SOT-23,T/R DR - QSOP, T/R DT – QSOP, TUBE PIN COUNT LEAD FREE PART PART NUMBER X = Automotive (-40C to +125C) I = Industrial (-40C to +85C) P or n/c = Commercial (0C to +70C) 1 – reserved 2 - Non PLL based 3 – EMI Reduction 4 – DDR support products 5 – STD Zero Delay Buffer 6 – power management 7 – power management 8 – power management 9 – Hi performance 0 - reserved Alliance Semiconductor Mixed Signal Product Licensed under US patent #5,488,627, #6,646,463 and #5,631,920. Peak Reducing EMI Solution 7 of 8 March 2005 rev 1.3 ASM3P2111A Alliance Semiconductor Corporation 2575, Augustine Drive, Santa Clara, CA 95054 Tel# 408-855-4900 Fax: 408-855-4999 www.alsc.com Copyright © Alliance Semiconductor All Rights Reserved Part Number: ASM3P2111A Document Version: v1.3 Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to Alliance Semiconductor, dated 11-11-2003 © Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use. Peak Reducing EMI Solution 8 of 8