002540113

OVERVIEW INTRODUCTION SCREW TERMINAL BLOCKS SCREW CLAMP CONNECTION TECHNOLOGY • Maximum wiring efficiency and reliability • Supplied with open clamps ready to accept wires • No wire preparation necessary (with/ without ferrule) • Vibration resistant/ Gas-tight connection • For very larger wire sizes (up to 250 kcmil) • Designed for most stringent requirements • Simple connection with standard flat head screwdriver E220514 60947-7-1 MATERIAL SPECIFICATIONS Housing Screw Current Bar Terminal Clamp Current Carrying Metal Corrosion free material Terminal Block Housing • Polyamide PA66 Housing • Self-extinguishing • High mechanical strength • Clamp: zinc chromate passivated steel • Screw: zinc chromate passivated steel • Current Bar: nickel plated copper alloy / tin plated copper Polyamide 66 Specifications Upper Temperature Limit: 105°C Lower Temperature Limit: -50°C Flammability UL94: V2/ V0 Volume Resistivity: 1012 Ω cm Surface Resistivity: 1010 Ω INSTALLATION GUIDELINES 1 2 Secure Connection 3 1 Insert Wire into open clamp 2 Tighten screw to specified torque 3 Remove Screwdriver, screw terminal is closed with locking feature for a reliable/ safe connection SCREW CLAMP ACCESSORIES AND FEATURES Internal Jumper Isolated Internal Jumper Separator Plate Shorting Screw Current Bar Shorting Sleeve End Plate Isolation Partition DIN Rail External Jumper End Stop 4 Marking Tags Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 OVERVIEW SELECTION GUIDE SCREW TERMINAL BLOCKS Feed Through Terminal Blocks • • • • • • • Up to 240A Multi-Connection Terminals Double Level Terminal Triple Level Terminals Ground Blocks Wide range of accessories All standard colors Feed Through Multi-Connection Double Level Triple Level Ground / Earth page 6-8 page 9 page 10-12 page 14-15 page 16-17 5x20mm / 5x25mm CF4U / CF4SP Double Lever DDFL4U 1/4”x1” CAFL4U Component Carrier CCC4U Fuse Holder page 18-19 page 20-21 page 22 page 23 page 24-25 Slider Style CDS6U Blade Style CKT4U Blade Style CKT4SP Slider Style CDTTU Lever Style CSDL4U page 26-27 page 28 page 29 page 30 page 31 Fuse Terminal Blocks • • • • • 1/4" x 1" Fuse Terminal Blocks 5x20mm/ 5x25mm Fuse Terminal Blocks Double level versions Component Carrier for flexible requirements 10x38, CC, J-Type Fuse Holder Disconnect & Test Terminal Blocks • • • • Slider Style Blade/ Knife Style Lever Style Accessories and matching Feed Through terminals Power Distribution Terminal Blocks • Various I/O configurations • Up to 150A • Compact Hybrid Distribution Block CDB Series CMDB Series Hybrid CXDB Series Distribution/Grounding page 32-33 page 34 page 35 page 36 Special Application Terminal Blocks • Spring Loaded Terminals for high vibration applications • 1000V High Voltage Terminals • Thermocouple Terminals • Tab Connection Terminals • Electronic Components Terminals 1000V High Voltage CHV Series Thermocouple CTT2.5U Series Tab Connection CTC Series Spring Loaded USC Series Electronic Components page 37 page 38 page 39 page 36-37 page 42-47 Accessories • • • • • Internal Jumpers (Uninsulated, Insulated) Endplates Partition/ Separator Plates Protective Covers End Stops Jumpers Endplates, Separators, End Stops, Covers, etc. page 48 page 49 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 5 FEED-THROUGH SINGLE LEVEL TERMINAL BLOCKS SCREW TERMINAL BLOCKS CTS2.5U-N CTS4U-N CTS6U HIGHLIGHTS FEATURES • Altech CTS Series of Universal Screw Terminal Blocks featuring global standards • Universal mounting foot for easy snap onto common DIN rail profiles • Screw-type jumper system • Current Ratings up to 240A APPLICATIONS • Ex & IECEx approvals for use in potentially explosive areas • Control, Automation applications Dimensions & Weight Width 5 mm 6 mm 8 mm Length 43 mm 43 mm 43 mm 46.2 mm 53.7 mm 46.2 mm 53.7 mm 47.8 mm 55.5 mm 6.2 g 7.6 g 13.5 g Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Technical Data/Ratings Approvals Wire Size (solid / stranded) 22-10 AWG 0.2-4 mm2 22-8 AWG 0.5-6 mm2 600 V 1000V AC/DC 600 V 1000V AC/DC 600 V 1000V AC/DC Voltage Rating Current Rating 25 A 24 A 35 A 32 A 50 A 41 A Torque 7 lb-in 0.4 Nm 7 lb-in 0.5 Nm 14 lb-in 0.8 Nm Polyamide 66 Polyamide 66 Polyamide 66 8 mm 8 mm 9 mm Flat Head 0.5 x 3.0 mm Flat Head 0.6 x 3.5 mm Flat Head 0.8 x 4.0 mm Installation Instructions Wire Stripping Length Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W Mounting Handle Mounting handle is used for mounting 10 terminal blocks on a DIN rail, thus saving considerable time. Specially designed pins in the mounting handle grip the terminal blocks when pressed against entry. Cat. No. Terminal Block Std. Pk. 6 60947-7-1 E220514 0.2-2.5 mm2 Screwdriver MH2.5 CTS2.5U-N 1 MH4 1 CTS4U-N 60947-7-1 E220514 22-12 AWG Insulation Material • Power Distribution 60947-7-1 E220514 AEx ell Ex ell U CTS2.5U-N CTS2.5U-N/R CTS2.5U-N/BU CTS2.5U-N/BL CTS2.5U-N/O CTS2.5U-N/G CTS2.5U-N/Y CTS2.5U-N/W Accessories Std. Pk. 100 100 100 100 100 100 100 100 Cat. No. CTS4U-N CTS4U-N/R CTS4U-N/BU CTS4U-N/BL CTS4U-N/O CTS4U-N/G CTS4U-N/Y CTS4U-N/W Std. Pk. 100 100 100 100 100 100 100 100 Cat. No. CTS6U CTS6U/R CTS6U/BU CTS6U/BL CTS6U/O CTS6U/G CTS6U/Y CTS6U/W Std. Pk. 100 100 100 100 100 100 100 100 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EP2.5/4UN 50 EP2.5/4UN 50 EP6/10U 50 Partition Plate PP2.5/4UN 50 PP2.5/4UN 50 PP6/10U 50 Separator Plate SP2.5/4UN 100 SP2.5/4UN 100 SP6/10U 100 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA721/2 CA721/3 CA721/4 CA721/10 CA721/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 50 10 10 CA723/2 CA723/3 CA723/4 CA723/10 – 100 50 50 10 – Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA741/2 CA741/3 CA741/4 CA741/10 CA741/100 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 CA743/2 CA743/3 CA743/4 CA743/10 – 100 50 50 10 – External Jumper 2 pole 3 pole 4 pole 10 pole CA717/2 CA717/3 CA717/4 CA717/10 100 100 100 20 CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 CA710/2 CA710/3 CA710/4 CA710/10 100 50 50 20 Test Socket CA707/TS/01 100 CA707/TS/01 100 CA707/TS/05 100 Marking Tag MT5 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT8 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 1 Pk. (100 tags) FEED-THROUGH SINGLE LEVEL TERMINAL BLOCKS SCREW TERMINAL BLOCKS CTS10U CTS16U CTS25UN CTS35UN Dimensions & Weight Width 10 mm 12 mm 12 mm 16 mm Length 43 mm 43 mm 49 mm 50.5 mm 47.8 mm 55.5 mm 47.8 mm 55.5 mm 57.2 mm 64.7 mm 59.2 mm 66.7 mm 16.5 g 25.5 g 35.5 g 50.5 g Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Technical Data/Ratings Approvals 60947-7-1 E220514 AEx ell Ex ell U Wire Size (solid / stranded) Voltage Rating 16-6 AWG 22-6 AWG 0.5-10 mm2 600 V Current Rating Torque 60947-7-1 E220514 600 V 1000V AC/DC 600 V 60947-7-1 E220514 20-4 AWG 22-6 AWG 0.2-16 mm2 60947-7-1 E220514 14-2 AWG 4-25 mm2 12-1/0 AWG 4-35 mm2 600 V 1000V AC/DC 600 V 1000V AC/DC 600 V 1000V AC/DC 65 A 65 A 57 A 85 A 70 A 76 A 105 A 101 A 150 A 125 A 14 lb-in 14 lb-in 1.2 Nm 14 lb-in 14 lb-in 1.2 Nm 30 lb-in 2.0 Nm 50 lb-in 2.5 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 Polyamide 66 11 mm 12 mm 14 mm 15 mm Flat Head 0.8 x 4.0 mm Flat Head 1.0 x 5.5 mm Flat Head 1.0 x 5.5 mm Flat Head 1.0 x 5.5 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. CTS10U CTS10U/R CTS10U/BU CTS10U/BL CTS10U/O CTS10U/G CTS10U/Y CTS10U/W Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W Accessories Std. Pk. 100 100 100 100 100 100 100 100 Cat. No. CTS16U CTS16U/R CTS16U/BU CTS16U/BL CTS16U/O CTS16U/G CTS16U/Y CTS16U/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CTS25UN CTS25UN/R CTS25UN/BU CTS25UN/BL CTS25UN/O CTS25UN/G CTS25UN/Y CTS25UN/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CTS35UN CTS35UN/R CTS35UN/BU CTS35UN/BL CTS35UN/O CTS35UN/G CTS35UN/Y CTS35UN/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. Std. Pk. End Plate EP6/10U 50 – – – – – – Partition Plate PP6/10U 50 – – PP25UN 50 PP35UN 50 Separator Plate SP6/10U 100 SP6/10U 100 – – DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. – Std. Pk. – Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA724/2 CA724/3 CA724/4 CA724/10 – 100 50 50 10 – CA751/2 CA751/3 CA751/4 CA751/10 CA751/100 50 50 50 10 10 CA725/2 CA725/3 CA725/4 CA725/10 CA725/100 50 20 20 10 10 CA771/2 CA771/3 CA771/4 CA771/10 – 50 20 20 10 – Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA744/2 CA744/3 CA744/4 CA744/10 – 100 50 50 10 – CA761/2 CA761/3 CA761/4 CA761/10 CA761/100 100 50 50 10 10 CA745/2 CA745/3 CA745/4 CA745/10 CA745/100 50 20 20 10 10 CA781/2 CA781/3 CA781/4 CA781/10 – 50 20 20 10 – External Jumper 2 pole 3 pole 4 pole 10 pole CA718/2 CA718/3 CA718/4 CA718/10 100 50 50 20 – – – – – – – – – – – – – – – – – – – – – – – – Test Socket CA707/TS/05 100 CA707/TS/05 100 CA707/TS/06 100 CA707/TS/06 100 Marking Tag MT10 1 Pk. (100 tags) MT12 1 Pk. (100 tags) MT12 1 Pk. (100 tags) MT16 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 1 Pk. (100 tags) 7 FEED-THROUGH SINGLE LEVEL POWER TERMINAL BLOCKS SCREW TERMINAL BLOCKS CTS50/70N CTS50/70NA CTS95/120N HIGHLIGHTS FEATURES • DIN Rail and Panel • • • • mountable Voltage Rating 1000V Current Rating up to 240A Hex Screw version for easier tightening (NA) Auxiliary block for easy plug in APPLICATIONS • Power Distribution • Solar Applications • AUX6 auxiliary for Dimensions & Weight with Allen Screw Width 20.5 mm 20.5 mm 27.0 mm Length 77.3 mm 77.3 mm 84.5 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 71.1 mm 78.1 mm 71.1 mm 78.1 mm 83.0 mm 90.5 mm 93.8 g 95.0 g 177.2 g Weight per piece Technical Data/Ratings Approvals CB SCHEME Wire Size (solid / stranded) indicator light or contactor with Allen Screw 60947-7-1 E220514 60947-7-1 E220514 60947-7-1 E220514 8-2/0 AWG 10-70 mm2 8-2/0 AWG 10-70 mm2 2-250 KCMIL 25-120 mm2 Voltage Rating 1000 V 1000 V AC/DC 1000 V 1000 V AC/DC 1000 V 1000 V AC/DC Current Rating 175 A 192 A 175 A 192 A 240 A 269 A Torque 38 lb-in 3 .0 Nm 38 lb-in 3.0 Nm 90 lb-in 6.0 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W Accessories 22 mm 24 mm Allen Wrench 5 mm Allen Wrench 6 mm Cat. No. CTS50/70N CTS50/70N/R CTS50/70N/BU CTS50/70N/BL CTS50/70N/O CTS50/70N/G CTS50/70N/Y CTS50/70N/W Cat. No. Std. Pk. 20 20 20 20 20 20 20 20 Std. Pk. Cat. No. Std. Pk. CTS50/70NA CTS50/70NA/R CTS50/70NA/BU CTS50/70NA/BL CTS50/70NA/O CTS50/70NA/G CTS50/70NA/Y CTS50/70NA/W Cat. No. 20 20 20 20 20 20 20 20 Std. Pk. Cat. No. Std. Pk. CTS95/120N CTS95/120N/R CTS95/120N/BU CTS95/120N/BL CTS95/120N/O CTS95/120N/G CTS95/120N/Y CTS95/120N/W Cat. No. 10 10 10 10 10 10 10 10 Std. Pk. DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Shorting Link System CA628/2 CA628/3 10 10 CA628/2 CA628/3 10 10 CA629/2 CA629/3 10 10 Marking Tag MT16 Cat. No AUX6 Auxiliary Terminal Block Used for: CTS50/70N CTS50/70NA CTS95/120N In certain power circuits, there is a need to take an extra connection for an Auxiliary circuit like an indicating light or contactor. The AUX6 terminal easily plugs into the terminal and provides this extra connection point. 8 22 mm Flat Head 1.0x7.5 mm 1 Pk. (100 tags) MT16 1 Pk. (100 tags) Ratings IEC60947-7-1 Voltage/Current: 1000 V / 41 A Torque: 0.8 Nm IEC 60079-7 Voltage/Current: 630 V / 36 A Torque: 0.8 Nm MT16 1 Pk. (100 tags) UL-1059 Voltage/Current: 600 V / 50 A Torque: 14 lb-in CSA22.2-158 Voltage/Current: 600 V / 50 A Torque: 14 lb-in Wire Range: 22-8 AWG Width x Length x Height: 8 x 53.6 x 29.4 mm Std. Pk.: 10 Marking Tag: MT8 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 FEED-THROUGH FEED THROUGH MULTI-CONNECTION SCREW TERMINAL BLOCKS CMCG4 CMC2-2 CMC1-2 HIGHLIGHTS FEATURES • 3 to 4 connections • Up to 2 connection Dimensions & Weight Width 6 mm 6 mm 6 mm Length 46.5 mm 65.0 mm 65.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 49.5 mm 56.5 mm 53.4 mm 60.5 mm 53.7 mm 60.9 mm 11.0 g 16.0 g 21.6 g Weight per piece points on each side • 2 jumper channels on Technical Data/Ratings Approvals 60947-7-1 E220514 Wire Size (solid / stranded) 60947-7-1 E220514 60947-7-1 E220514 22-10 AWG 0.2-4 mm2 22-10 AWG 0.2-4 mm2 24-10 AWG 0.2-4 mm2 Voltage Rating 600 V 630 V AC/DC 600 V 630 V AC/DC 600 V 1000 V AC/DC Current Rating 35 A 32 A 35 A 32 A - Torque 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm 4.5 lb-in Insulation Material Polyamide 66 Polyamide 66 0.5 Nm Screwdriver Terminal Blocks 9 mm 9 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm CMC1-2 CMC1-2/R CMC1-2/BU CMC1-2/BL CMC1-2/O CMC1-2/G CMC1-2/Y CMC1-2/W Accessories Std. Pk. 100 100 100 100 100 100 100 100 Cat. No. CMC2-2 CMC2-2/R CMC2-2/BU CMC2-2/BL CMC2-2/O CMC2-2/G CMC2-2/Y CMC2-2/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CMCG4 Yellow/Green Cat. No. 50 Std. Pk. Cat. No. Std. Pk. End Plate EPCMC1-2 50 EPCMC2-2 50 EPCMC2-2 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Std. Pk. Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 50 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 50 10 10 – – – – – – – – – – Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 – – – – – – – – – – External Jumper 2 pole 3 pole 4 pole 10 pole CA713/2 CA713/3 CA713/4 CA713/10 100 100 100 20 CA713/2 CA713/3 CA713/4 CA713/10 100 100 100 20 – – – – – – – – – – CA707/TS/01 Marking Tag MT6 CA707/TS/01 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT6 gle terminal block Std. Pk. Cat. No. Test Socket type of wires with different wire sizes into a sinapplications Flat Head 0.6 x 3.5 mm Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W APPLICATIONS • Connecting different • Simple distribution Polyamide 66 Installation Instructions Wire Stripping Length CMC2-2 for individual potential distribution • CMCG4 same profile as regular feed-through version 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 9 DOUBLE LEVEL FEED THROUGH DOUBLE LEVEL SCREW TERMINAL BLOCKS CDL4UN CDL4UN(I.S) Width 6 mm 6 mm Length 57.0 mm 57.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 59.5 mm 67.2 mm 59.5 mm 67.2 mm 13.8 g 15.6 g HIGHLIGHTS FEATURES • Accommodates larger MT6 marking tags on both levels • Independent and internally shorted version • CDL4UN offers jumper channel on both levels • Same profile Ground versions • Grounding Level on Dimensions & Weight Weight per piece Technical Data/Ratings CDLG4 is identified by green/yellow imprint Approvals Wire Size (solid / stranded) applications 60947-7-1 E220514 22-10 AWG 0.2-4 mm 22-10 AWG 0.2-4 mm2 600 V 800 V AC/DC 600 V 800 V AC/DC Voltage Rating APPLICATIONS • High density writing 60947-7-1 E220514 2 Current Rating 35 A 32 A 35 A 32 A Torque 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm Polyamide 66 Polyamide 66 9 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Insulation Material Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. CDL4UN CDL4UN/R CDL4UN/BU CDL4UN/BL CDL4UN/O CDL4UN/G CDL4UN/Y CDL4UN/W Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W 100 100 100 100 100 100 100 100 Cat. No. Std. Pk. CDL4UN(I.S) CDL4UN(I.S)/R CDL4UN(I.S)/BU CDL4UN(I.S)/BL CDL4UN(I.S)/O CDL4UN(I.S)/G CDL4UN(I.S)/Y CDL4UN(I.S)/W 100 100 100 100 100 100 100 100 Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPCDL4UN 50 EPCDL4UN 50 Separator Plate SPCDL4U 100 SPCDL4U 100 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Accessories 10 Std. Pk. Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 External Jumper 2 pole 3 pole 4 pole 10 pole CA714/2 CA714/3 CA714/4 CA714/10 100 50 50 20 CA714/2 CA714/3 CA714/4 CA714/10 100 50 50 20 Test Socket CA707/TS/01 100 CA707/TS/01 100 Marking Tag MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 DOUBLE LEVEL FEED THROUGH DOUBLE LEVEL SCREW TERMINAL BLOCKS CDLG4(I.S) CDLG4 CDLG2.5 Width 6 mm 6 mm 6 mm Length 57.0 mm 57.0 mm 71.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 59.5 mm 67.2 mm 59.5 mm 67.2 mm 53.0 mm 61.0 mm 22.2 g 20.6 g 20.2 g Dimensions & Weight Weight per piece Technical Data/Ratings Approvals 60947-7-1 E220514 CB SCHEME Wire Size (solid / stranded) 24-10 AWG 0.2-4 mm 150 V Voltage Rating 60947-7-1 E220514 60947-7-1 E220514 24-10 AWG 0.2-4 mm 24-12 AWG 0.2-2.5 mm2 500 V AC/DC 150 V 500 V AC/DC 300 V 500 V - - 32 A (upper level) 32 A 24 A 24 A 4.5 lb-in 0.5 Nm 4.5 lb-in 0.5 Nm 4.5 lb-in 0.4 Nm Current Rating Torque 2 Insulation Material 2 Polyamide 66 Polyamide 66 Polyamide 66 8 mm 8 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.5 x 3.0 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Std. Pk. Std. Pk. Cat. No. Std. Pk. 100 CDLG4 100 CDLG2.5 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPCDL4UN 50 EPCDL4UN 50 EPCDLG2.5 50 Separator Plate SPCDL4U 100 SPCDL4U 100 SPCDLG2.5 100 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 2511120 CA701-15/S 2511160 CA702 CA802 CA202 20 20 10 50 50 25 100 100 100 10 – Cat. No. Yellow/Green CDLG4(I.S) Accessories 100 Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 50 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 50 10 10 CA627/2 CA627/3 CA627/4 CA627/10 – Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 – – – – – External Jumper 2 pole 3 pole 4 pole 10 pole CA714/2 CA714/3 CA714/4 CA714/10 100 50 50 20 CA714/2 CA714/3 CA714/4 CA714/10 100 50 50 20 CA715/2 CA715/3 CA715/4 CA715/10 100 100 100 20 Test Socket CA707/TS/01 100 CA707/TS/01 100 CA707/TS/01 100 Marking Tag MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT2G – – – – – 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 11 DOUBLE LEVEL FEED THROUGH OFFSET DOUBLE LEVEL SCREW TERMINAL BLOCKS ODL4U HIGHLIGHTS FEATURES • Top Level is offset by half terminal width from lower level • Offset allows better ac- cess to both levels even when fully wired • Different Endplates for front and back side guarantee flush mounting to neighboring terminal blocks or end stops (EPODL4U and EP1ODL4U) APPLICATIONS • High density writing applications Dimensions & Weight Width 6 mm Length 68 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 65.0 mm 71.1 mm Weight per piece 14.5 g Technical Data/Ratings Approvals 60947-7-1 E220514 Wire Size (solid / stranded) 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 800 VAC/DC Current Rating 35 A 32 A Torque 7 lb-in 0.5 Nm Insulation Material Polyamide 66 Installation Instructions Wire Stripping Length 9 mm Screwdriver Flat Head 0.6 x 3.5 mm Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W ODL4U ODL4U/R ODL4U/BU ODL4U/BL ODL4U/O ODL4U/G ODL4U/Y ODL4U/W Accessories 12 ODL4U (without End Plates) Cat. No. Std. Pk. 100 100 100 100 100 100 100 100 EPODL4U (Front) EP1ODL4U (Back) 50 50 Separator Plate SPCDL4U 100 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA727/2 CA727/3 CA727/4 CA727/10 CA727/100 100 100 100 10 10 Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA747/2 CA747/3 CA747/4 CA747/10 CA747/100 100 100 100 10 10 External Jumper 2 pole 3 pole 4 pole 10 pole CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 CA707/TS/01 Marking Tag MT6 End Plate (Front) EPODL4U Std. Pk. End Plate Test Socket ODL4U (with End Plates) 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 End Plate (Back) EP1ODL4U DOUBLE LEVEL FEED THROUGH DOUBLE LEVEL SCREW TERMINAL BLOCKS ODLG2.5(I.S) ODLG2.5 ODL2.5(I.S) ODL2.5 Double Level with Offset Double Level with Offset Internally Shorted Upper / Lower Level Double Level with Offset Ground Connection Double Level with Offset Internally Shorted / Ground Connection Width 5 mm 5 mm 5 mm 5 mm Length 62.0 mm 62.0 mm 62.0 mm 62.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 63.0 mm 70.5 mm 63.0 mm 70.5 mm 63.0 mm 70.5 mm 63.0 mm 70.5 mm 13.0 g 14.2 g 15.3 g 17.0 g Dimensions & Weight Weight per piece UL Technical Data/Ratings Approvals UL 60947-7-1 UL 60947-7-1 UL 60947-7-1 60947-7-1 24-12 AWG 0.2-2.5 mm2 24-12 AWG 0.2-2.5 mm2 24-12 AWG 0.2-2.5 mm2 24-12 AWG 0.2-2.5 mm2 Voltage Rating 300 V 800 V AC/DC 300 V 800 V AC/DC 300 V 800 V AC/DC 300 V 800 V AC/DC Current Rating 25 A 24 A 25 A 24 A 25 A 24 A 24 A 24 A 4.5 lb-in 0.4 Nm 4.5 lb-in 0.4 Nm 4.5 lb-in 0.4 Nm 4.5 lb-in 0.4 Nm Wire Size (solid / stranded) Torque Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 Polyamide 66 Installation Instructions 8 mm 8 mm 8 mm 8 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Wire Stripping Length Screwdriver Terminal Blocks Grey Stackable Clip-on Accessories Cat. No. Std. Pk. ODL2.5 ODL2.5A 50 50 Cat. No. Std. Pk. Cat. No. ODL2.5(I.S) ODL2.5A(I.S) Cat. No. Std. Pk. 50 50 Std. Pk. Cat. No. ODLG2.5 ODLG2.5A Cat. No. Std. Pk. 50 50 Std. Pk. Cat. No. ODLG2.5(I.S) ODLG2.5A(I.S) Cat. No. Std. Pk. 50 50 Std. Pk. EPODL2.5 EP1ODL2.5 50 50 EPODL2.5 EP1ODL2.5 50 50 EPODL2.5 EP1ODL2.5 50 50 EPODL2.5 EP1ODL2.5 50 50 DIN Rail 2511120 CA701-15/S 20 20 2511120 CA701-15/S 20 20 2511120 CA701-15/S 20 20 2511120 CA701-15/S 20 20 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 JX2.5/2 JX2.5/3 JX2.5/4 JX2.5/5 JX2.5/6 JX2.5/7 JX2.5/8 JX2.5/10 100 50 50 50 10 10 10 10 JX2.5/2 JX2.5/3 JX2.5/4 JX2.5/5 JX2.5/6 JX2.5/7 JX2.5/8 JX2.5/10 100 50 50 50 10 10 10 10 JX2.5/2 JX2.5/3 JX2.5/4 JX2.5/5 JX2.5/6 JX2.5/7 JX2.5/8 JX2.5/10 100 50 50 50 10 10 10 10 JX2.5/2 JX2.5/3 JX2.5/4 JX2.5/5 JX2.5/6 JX2.5/7 JX2.5/8 JX2.5/10 MT5 End Plate Shorting Link/ Jumpers Marking Tag Front Side Back Side 2 pole 3 pole 4 pole 5 pole 6 pole 7 pole 8 pole 10 pole MT5 1 Pk. (100 tags) MT5 1 Pk. (100 tags) MT5 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 100 50 50 50 10 10 10 10 1 Pk. (100 tags) 13 TRIPLE LEVEL FEED THROUGH TRIPLE LEVEL SCREW TERMINAL BLOCKS CTL2.5U CTL2.5U-H CTL2.5U(I.S) HIGHLIGHTS FEATURES • 3 Feed through levels • Marking Tag space on all 3 levels • Independent Levels and internally shorted version CTL2.5U(I.S) • LED versions to show switching indication in various voltages CTL2.5U(L)/XX • 3 Level terminal with additional grounding level CTLG2.5 Dimensions & Weight Width 6 mm 6 mm 6 mm Length 84.0 mm 61.0 mm 84.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 68.0 mm 75.6 mm 68.0 mm 75.6 mm 68.0 mm 75.6 mm 20.0 g 21.0 g 21.0 g Weight per piece Technical Data/Ratings Approvals sensor applications • Actuator applications • Motor applications • Applications with high wire density 60947-7-1 E220514 0.2-2.5 mm2 22-12 AWG 0.2-2.5 mm 22-12 AWG 0.2-2.5 mm2 Voltage Rating 300 V 500 V AC/DC 300 V 500 V AC/DC 150 V 500 V AC/DC Current Rating 25 A 24 A 25 A 24 A 25 A 24 A 4.5 lb-in 0.4 Nm 4.5 lb-in 0.4 Nm 4.5 lb-in 0.4 Nm Torque 2 Polyamide 66 Polyamide 66 Polyamide 66 9 mm 9 mm 9 mm Flat Head 0.5 x 3.0 mm Flat Head 0.5 x 3.0 mm Flat Head 0.5 x 3.0 mm Insulation Material Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. CTL2.5U CTL2.5U/R CTL2.5U/BU CTL2.5U/BL CTL2.5U/O CTL2.5U/G CTL2.5U/Y CTL2.5U/W Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W Accessories 14 60947-7-1 E220514 22-12 AWG Wire Size (solid / stranded) APPLICATIONS • Control Systems with 60947-7-1 E220514 Cat. No. Std. Pk. 50 50 50 50 50 50 50 50 Std. Pk. Cat. No. CTL2.5U-H CTL2.5U-H/R CTL2.5U-H/BU CTL2.5U-H/BL CTL2.5U-H/O CTL2.5U-H/G CTL2.5U-H/Y CTL2.5U-H/W Cat. No. Std. Pk. 50 50 50 50 50 50 50 50 Std. Pk. Cat. No. Std. Pk. CTL2.5U(I.S) CTL2.5U(I.S)/R CTL2.5U(I.S)/BU CTL2.5U(I.S)/BL CTL2.5U(I.S)/O CTL2.5U(I.S)/G CTL2.5U(I.S)/Y CTL2.5U(I.S)/W Cat. No. 50 50 50 50 50 50 50 50 Std. Pk. End Plate EPCTL2.5U 50 EPCTL2.5U-H 50 EPCTL2.5U 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 External Jumper 2 pole 3 pole 4 pole 10 pole CA715/2 CA715/3 CA715/4 CA715/10 100 100 100 20 CA715/2 CA715/3 CA715/4 CA715/10 100 100 100 20 CA715/2 CA715/3 CA715/4 CA715/10 100 100 100 20 Test Socket CA707/TS/01 100 CA707/TS/01 100 CA707/TS/01 100 Marking Tag MT2 1 Pk. (100 tags) MT2 1 Pk. (100 tags) MT2 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 1 Pk. (100 tags) TRIPLE LEVEL FEED THROUGH TRIPLE LEVEL SCREW TERMINAL BLOCKS CTLG2.5 CTL2.5UH(I.S)D2 CTL2.5U(L)/XX CTL2.5U-H(L)/XX Dimensions & Weight Width 6 mm 6 mm 6 mm 6 mm Length 61.0 mm 84.0 mm 61.0 mm 87.5 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 68.0 mm 75.6 mm 68.0 mm 75.6 mm 68.0 mm 75.6 mm 66.0 mm 74.0 mm 21.0 g 21.0 g 15.1 g 27.4 g Weight per piece Technical Data/Ratings Approvals 60947-7-1 E220514 Wire Size (solid / stranded) 22-12 AWG 0.2-2.5 mm 300 V 500 V AC/DC Voltage Rating 60947-7-1 E220514 60947-7-1 E220514 22-12 AWG 0.2-2.5 mm 22-12 AWG 0.2-2.5 mm 24-12 AWG 0.2-2.5 mm2 300 V 500 V AC/DC 150 V 500 V AC/DC 300 V 440 V 2 2 25 A 24 A 25 A 24 A 25 A 24 A 24 A 24 A 4.5 lb-in 0.4 Nm 4.5 lb-in 0.4 Nm 4.5 lb-in 0.4 Nm 4.5 lb-in 0.4 Nm Current Rating Torque 60947-7-1 E220514 2 Polyamide 66 Polyamide 66 Polyamide 66 Polyamide 66 9 mm 9 mm 9 mm 9 mm Flat Head 0.5 x 3.0 mm Flat Head 0.5 x 3.0 mm Flat Head 0.5 x 3.0 mm Flat Head 0.6 x 3.5 mm Insulation Material Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. CTL2.5UH(I.S)D2 Grey LED Voltage 12 V LED Voltage 24 V LED Voltage 48 V LED Voltage 110 V LED Voltage 220 V CTL2.5U-H(L)/12 CTL2.5U-H(L)/24 CTL2.5U-H(L)/48 CTL2.5U-H(L)/110 CTL2.5U-H(L)/220 Accessories Cat. No. 50 50 50 50 50 Std. Pk. CTL2.5U(L)/12 CTL2.5U(L)/24 CTL2.5U(L)/48 CTL2.5U(L)/110 CTL2.5U(L)/220 Cat. No. 50 50 50 50 50 50 Std. Pk. Cat. No. Cat. No. CTLG2.5 Yellow/Green Std. Pk. 100 Std. Pk. Cat. No. Std. Pk. End Plate EPCTL2.5U-H 50 EPCTL2.5U 50 EPCTL2.5U-H 50 EPCTLG2.5 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA627/2 CA627/3 CA627/4 CA627/10 – 100 100 100 10 – External Jumper 2 pole 3 pole 4 pole 10 pole CA715/2 CA715/3 CA715/4 CA715/10 100 100 100 20 CA715/2 CA715/3 CA715/4 CA715/10 100 100 100 20 CA715/2 CA715/3 CA715/4 CA715/10 100 100 100 20 CA715/2 CA715/3 CA715/4 CA715/10 100 100 100 20 Test Socket CA707/TS/01 100 CA707/TS/01 100 CA707/TS/01 100 CA707/TS/01 100 Marking Tag MT2 1 Pk. (100 tags) MT2 1 Pk. (100 tags) MT2 1 Pk. (100 tags) MT2G Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 1 Pk. (100 tags) 15 GROUND GROUND/EARTH TERMINAL BLOCKS SCREW TERMINAL BLOCKS CGT4U CGT6N CGT4N HIGHLIGHTS FEATURES • Yellow/Green color code as per industry standard • Clamp mechanically on Rail by tightening middle screw • Rail serves as grounding busbar to feed ground potential to all other grounding terminals • CGT4N, CGT6N, CGT10N and CGT16N have same profile as respective feed through blocks • CGT4U, CGT10U, and CGT35U mount on both 35mm and 32mm DIN-Rail APPLICATIONS • Grounding Applications Dimensions & Weight Width 6 mm 6 mm 8 mm Length 43 mm 54.2 mm 54.5 mm 49.5 mm 56.7 mm 47.0 mm 54.4 mm 48.2 mm 55.8 mm 21.5 g 22.0 g 27.0 g Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Technical Data/Ratings Approvals AEx ell Ex ell U Wire Size (solid / stranded) 60947-7-1 E220514 22-10 AWG Voltage Rating 600 V Current Rating 60947-7-1 E220514 0.2-4 mm2 22-10 AWG 800 V AC/DC 600 V – Torque 7.0 lb-in Insulation Material 22-8 AWG 1000 V AC/DC 600 V – 0.5 Nm 7 lb-in Polyamide 66 0.2-6 mm2 1000 V AC/DC – 0.5 Nm 14 lb-in Polyamide 66 1.6 Nm Polyamide 66 Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks 8 mm 8 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.8 x 4.0 mm Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Yellow/Green CGT4U 50 CGT4N 50 CGT6N 50 Accessories Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPCGT4U/Y 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 Marking Tag MT6 1 Pk. (100 tags) – 2511120 CA701-15/S 2511160 MT6 – 20 20 10 1 Pk. (100 tags) – 2511120 CA701-15/S 2511160 MT8 Assembly example for single phase 3 wire circuits. 16 60947-7-1 E220514 0.2-4 mm2 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 – 20 20 10 1 Pk. (100 tags) GROUND GROUND/EARTH TERMINAL BLOCKS SCREW TERMINAL BLOCKS CGT10U CGT10N CGT16N CGT35U Dimensions & Weight Width 10 mm 10 mm 12 mm 16 mm Length 45.0 mm 55.0 mm 55.0 mm 58.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 51.0 mm 58.2 mm 48.5 mm 56.0 mm 48.5 mm 56.0 mm 63.7 mm 70.5 mm 30.5 g 35.2 g 39.6 g 102.0 g Weight per piece IEC Technical Data/Ratings Approvals E220514 AEx ell Ex ell U Wire Size (solid / stranded) Voltage Rating 60947-7-1 16-8 AWG 22-6 AWG 0.2-10 mm2 600 V 600 V Current Rating 60947-7-1 E220514 16-6 AWG 1000 V AC/DC 14 lb-in Torque Insulation Material 0.2-10 mm2 20-4 AWG 1000 V AC/DC 600 V 600 V – 60947-7-1 E220514 – 14 lb-in 1.6 Nm 14 lb-in Polyamide 66 E220514 0.2-16 mm2 8-2 AWG 1000 V AC/DC 600 V – 1.6 Nm 14 lb-in Polyamide 66 2.5-35 mm2 1000 V AC/DC – 1.6 Nm 25 lb-in Polyamide 66 2.8 Nm Polyamide 66 Installation Instructions 11 mm 11 mm 12 mm 15 mm Flat Head 0.8 x 4.0 mm Flat Head 0.8 x 4.0 mm Flat Head 1.0 x 5.5 mm Flat Head 1.0 x 5.5 mm Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Yellow/Green CGT10U 50 CGT10N 50 CGT16N 50 CGT35U 20 Accessories Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate – DIN Rail 2511120 CA701-15/S 2511160 Marking Tag MT10 – 20 20 10 1 Pk. (100 tags) – 2511120 CA701-15/S 2511160 MT10 – 20 20 10 1 Pk. (100 tags) – 2511120 CA701-15/S 2511160 MT12 – 20 20 10 1 Pk. (100 tags) – 2511120 CA701-15/S 2511160 MT16 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 – 20 20 10 1 Pk. (100 tags) 17 FUSE BLOCKS FUSE BLOCKS, 5 x 20 and 5 x 25 mm SCREW TERMINAL BLOCKS CF4U(L)/6-60V CF4U CF4U(L)/110-240V HIGHLIGHTS FEATURES • CF4U Series accepts 5x20mm/ 5x25mm fuse types • Completely enclosed, no endplates • CF4U(L) version with LED for blown fuse indication • Large marking area • No polarity required • Blocks can be used for AC & DC Voltages APPLICATIONS • Control systems with fuse protection 220KΩ 27KΩ Dimensions & Weight Width 8 mm 8 mm 8 mm Length 57.0 mm 57.0 mm 57.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 50.3 mm 57.6 mm 50.3 mm 57.6 mm 50.3 mm 57.6 mm 14.8 g 15.4 g 15.4 g Weight per piece Technical Data/Ratings Approvals 60947-7-3 E220514 60947-7-3 E220514 60947-7-3 E220514 22-10 AWG 0.2-4 mm2 22-10 AWG 0.2-4 mm2 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 800 V AC/DC 600 V 800 V AC/DC 600 V 800 V AC/DC Current Rating 10 A 6.3 A 10 A 6.3 A 10 A 6.3 A Torque 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm Wire Size (solid / stranded) Polyamide 66 Polyamide 66 Polyamide 66 5x20 mm / 5 x 25 mm 5x20 mm / 5 x 25 mm 5x20 mm / 5 x 25 mm - 6-60V AC/DC 110-240V AC/DC Insulation Material Fuse Specifications Fuse Type LED Indicator Voltage Installation Instructions 9.5 mm 9.5 mm 9.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Blue BU Black BL Accessories 2 pole 3 pole 4 pole 10 pole On Terminal On Fuse Carrier Std. Pk. CF4U(L)/6-60V CF4U(L)/6-60V/BU CF4U(L)/6-60V/BL Cat. No. 50 50 50 Std. Pk. Cat. No. Std. Pk. CF4U(L)/110-240V 50 CF4U(L)/110-240V/BU 50 CF4U(L)/110-240V/BL 50 Cat. No. Std. Pk. 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 20 CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 20 CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 20 MT8 MT6 Fuses 5 x 20 mm 18 Std. Pk. Cat. No. 1 Pk. (100 tags) 1 Pk. (100 tags) MT8 MT6 1 Pk. (100 tags) 1 Pk. (100 tags) MT8 MT6 1 Pk. (100 tags) 1 Pk. (100 tags) Current Rating 0.1A 0.2A 0.5A Slow Blow Cat. No 0.1M5x20T 0.2M5x20T 0.5M5x20T Fast Blow Cat. No 0.1M5x20F 0.2M5x20F 0.5M5x20F Ø5mm (0.2 in.) 1.0A 2.0A 4.0A 1.0M5x20T 2.0M5x20T 4.0M5x20T 1.0M5x20F 2.0M5x20F 4.0M5x20F 20mm (0.79 in.) Marking Tag 50 50 50 Cat. No. DIN Rail External Jumper Std. Pk. CF4U CF4U/BU CF4U/BL 5.0A 6.3A 8.0A 10.0A 5.0M5x20T 6.3M5x20T 8.0M5x20T 10.0M5x20T 5.0M5x20F 6.3M5x20F 8.0M5x20F 10.0M5x20F Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 FUSE BLOCKS FUSE BLOCKS, 5 x 20 and 5 x 25 mm SCREW TERMINAL BLOCKS CF4SP(L)/6-60V CF4SP CF4SP(L)/110-240V HIGHLIGHTS FEATURES • CF4SP Series accepts 5x20mm fuse types • 6mm wide, compact design • Internal shorting channel • Completely enclosed, no 220KΩ 27KΩ Dimensions & Weight Width 6 mm 6 mm 6 mm Length 58.5 mm 58.5 mm 58.5 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 70.0 mm 77.5 mm 70.0 mm 77.5 mm 70.0 mm 77.5 mm 16.9 g 17.4 g 17.4 g Weight per piece endplates • CF4SP(L) version with LED for blown fuse indication • No polarity required Technical Data/Ratings Approvals 60947-7-3 E220514 60947-7-3 E220514 60947-7-3 E220514 24-10 AWG 0.2-4 mm2 24-10 AWG 0.2-4 mm2 24-10 AWG 0.2-4 mm2 Voltage Rating 600 V 1000 V AC/DC 600 V 1000 V AC/DC 600 V 1000 V AC/DC Current Rating 10 A 10 A 10 A 10 A 10 A 10 A 4.5 lb-in 0.5 Nm 4.5 lb-in 0.5 Nm 4.5 lb-in 0.5 Nm Wire Size (solid / stranded) Torque Polyamide 66 Polyamide 66 Polyamide 66 5x20 mm / 5 x 25 mm 5x20 mm / 5 x 25 mm 5x20 mm / 5 x 25 mm - 6-60V AC/DC 110-240V AC/DC Insulation Material APPLICATIONS • Control systems with fuse protection • Control Circuits with alternating configuration with (CF4SPFT, CKT4SP, etc...) Fuse Specifications Fuse Type LED Indicator Voltage Installation Instructions 8 mm 8 mm 8 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Blue BU Black BL CF4SP CF4SP/BU CF4SP/BL Accessories Cat. No. Insulated Internal Jumper External Jumper Marking Tag 50 50 50 Std. Pk. Cat. No. Std. Pk. CF4SP(L)/6-60V CF4SP(L)/6-60V/BU CF4SP(L)/6-60V/BL Cat. No. 50 50 50 Std. Pk. Cat. No. Std. Pk. CF4SP(L)/110-240V 50 CF4SP(L)/110-240V/BU50 CF4SP(L)/110-240V/BL50 Cat. No. 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2 pole 3 pole 4 pole 10 pole 100 pole CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 2 pole 3 pole 4 pole 10 pole 100 pole CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 2 pole 3 pole 4 pole 10 pole CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 On Terminal On Fuse Carrier MT6 MT6 1 Pk. (100 tags) 1 Pk. (100 tags) MT6 MT6 1 Pk. (100 tags) 1 Pk. (100 tags) MT6 MT6 CF4SPFT Std. Pk. 2511120 CA701-15/S 2511160 DIN Rail Internal Jumper Std. Pk. Feed Through Terminal Same Profile as CF4SP Technical Data/Ratings E220514 60947-7-1 24-10 AWG 0.2-4 mm2 600 V 1000 V 30 A 32 A 4.5 lb-in 0.5 Nm Polyamide 66 1 Pk. (100 tags) 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 19 FUSE BLOCKS DOUBLE LEVEL FUSE BLOCKS, 5 x 20 / 5 x 25 mm SCREW TERMINAL BLOCKS DDFL4U DDFL4U(E)/XX HIGHLIGHTS FEATURES • Top Level fuse link for 5x20mm/ 5x25mm fuse types • Bottom Level Feed through terminal • DDFL4U(E) version with LED for blown fuse indication in various voltages • Blocks can be used in AC & DC applications Width 8 mm 8 mm Length 88 mm 88 mm 67.4 mm 74.3 mm 67.4 mm 74.3 mm 28.0 g 27.0 g Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Technical Data/Ratings Approvals • No need for additional Feed through terminal 60947-7-1 E220514 Wire Size (solid / stranded) APPLICATIONS • Tight space fuse applications Dimensions & Weight 60947-7-1 E220514 22-10 AWG 0.2-4 mm 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 800 V AC/DC 600 V 800 V AC/DC Current Rating (top) 6.3 A 6.3 A 6.3 A 6.3 A Current Rating (bottom) 35 A 32 A 35 A 32 A Torque 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm Insulation Material 2 Polyamide 66 Polyamide 66 Fuse Specifications Fuse Type 5x20 mm / 5 x 25 mm 5x20 mm / 5 x 25 mm - 24V, 48V, 110V, 220V, 440V LED Indicator Voltage Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Grey LED Voltage 24V AC/DC LED Voltage 48V AC/DC LED Voltage 110V AC/DC LED Voltage 220V AC/DC LED Voltage 440V AC Accessories 9.5 mm Flat Head 0.6 x 3.5 mm Cat. No. Std. Pk. DDFL4U 20 Cat. No. Std. Pk. DDFL4U(E)/24 DDFL4U(E)/48 DDFL4U(E)/110 DDFL4U(E)/220 DDFL4U(E)/440 20 20 20 20 20 Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPDDFL4U 50 EPDDFL4U 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Internal Jumper 2 pole 3 pole 4 pole 10 pole CA729/2 CA729/3 CA729/4 CA729/10 100 50 50 10 CA729/2 CA729/3 CA729/4 CA729/10 100 50 50 10 Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole CA749/2 CA749/3 CA749/4 CA749/10 100 50 50 10 CA749/2 CA749/3 CA749/4 CA749/10 100 50 50 10 External Jumper 2 pole 3 pole 4 pole 10 pole CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 20 CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 20 Marking Tag 20 9.5 mm Flat Head 0.6 x 3.5 mm on terminal on lever MT8 MT2 1 Pk. (100 tags) 1 Pk. (100 tags) MT8 MT2 1 Pk. (100 tags) 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 DOUBLE LEVEL FUSE BLOCKS, 5 x 20 / 5 x 25 mm WITH 2 CONNECTION POINTS DDFL4ULR FUSE BLOCKS SCREW TERMINAL BLOCKS DDFL4U(E)LR/XX HIGHLIGHTS FEATURES • Modified version of DDFL4U with 2 equipotential Dimensions & Weight • DDFL4U(E) version with Width 8 mm 8 mm Length 88 mm 88 mm 67.4 mm 74.3 mm 67.4 mm 74.3 mm 24.5 g 27.0 g Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece LED for blown fuse indication in various voltages • Blocks can be used in AC & DC applications Technical Data/Ratings Approvals 60947-7-1 E220514 Wire Size (solid / stranded) 60947-7-1 E220514 22-10 AWG 0.2-4 mm2 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 800 V AC/DC 600 V 800 V AC/DC Current Rating (top) 6.3 A 6.3 A 6.3 A 6.3 A Torque 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm Insulation Material Polyamide 66 APPLICATIONS • Control Circuits with multi wire fuse application Polyamide 66 Fuse Specifications Fuse Type 5x20 mm / 5 x 25 mm 5x20 mm / 5 x 25 mm - 24V, 48V, 110V, 220V, 440V 9.5 mm 9.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm LED Indicator Voltage Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey LED Voltage 24V AC/DC LED Voltage 48V AC/DC LED Voltage 110V AC/DC LED Voltage 220V AC/DC LED Voltage 440V AC Accessories DDFL4ULR Std. Pk. Cat. No. Std. Pk. 20 DDFL4U(E)LR/24 DDFL4U(E)LR/48 DDFL4U(E)LR/110 DDFL4U(E)LR/220 DDFL4U(E)LR/440 20 20 20 20 20 Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPDDFL4U 50 EPDDFL4U 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 Internal Jumper 2 pole 3 pole 4 pole 10 pole CA729/2 CA729/3 CA729/4 CA729/10 100 50 50 10 CA729/2 CA729/3 CA729/4 CA729/10 100 50 50 10 Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole CA749/2 CA749/3 CA749/4 CA749/10 100 50 50 10 CA749/2 CA749/3 CA749/4 CA749/10 100 50 50 10 External Jumper 2 pole 3 pole 4 pole 10 pole CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 20 CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 20 Marking Tag on terminal on lever MT8 MT2 1 Pk. (100 tags) 1 Pk. (100 tags) MT8 MT2 1 Pk. (100 tags) 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 21 FUSE BLOCKS FUSE BLOCKS, SCREW TERMINAL BLOCKS CAFL4U 1/4 x 1 and CAFL4U(L)/XX 1/4 x 11/4 in. CAFL4U(N) HIGHLIGHTS FEATURES • CAFL4U Series accepts • • • • 1/4” x 1-1/4” (6.3x32mm) fuse types CAFL4U(L) versions with LED for blown fuse indication (24V, 48V, 110V, 220V) CAFL4U(N) version with Neon bulb for blown fuse indication Large marking area Blocks can be used in AC & DC applications APPLICATIONS • Control systems with 1/4” x 1-1/4” fuse protection Dimensions & Weight Width 9 mm 9 mm 9 mm Length 72 mm 72 mm 72 mm 55.3 mm 63.0 mm 55.3 mm 63.0 mm 55.3 mm 63.0 mm 20.5 g 20.5 g 20.5 g Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Technical Data/Ratings Approvals 60947-7-3 E220514 Wire Size (solid / stranded) 60947-7-3 E220514 60947-7-3 E220514 22-10 AWG 0.2-4 mm 22-10 AWG 0.2-4 mm 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 1000 V 600 V 1000 V 600 V 1000 V Current Rating 16 A 6.3 A 16 A 6.3 A 16 A 6.3 A Torque 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm Insulation Material 2 Polyamide 66 2 Polyamide 66 Polyamide 66 Installation Instructions Wire Stripping Length Screwdriver 9.5 mm 9.5 mm 9.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm 1/4” x 1” (6.3 x 32 mm) 1/4” x 1” (6.3 x 32 mm) 1/4” x 1” (6.3 x 32 mm) - 24V, 48V, 110V, 220V 110V - 240V Fuse Specifications Fuse Type LED/Neon Indicator Voltage Terminal Blocks Cat. No. Grey (standard) Blue BU Black BL LED Voltage 24V AC/DC LED Voltage 48V AC/DC LED Voltage 110V AC/DC LED Voltage 220V AC/DC Neon Bulb 110-300V AC/DC Accessories Std. Pk. Cat. No. – – – – – – – CAFL4U(L)/24 CAFL4U(L)/48 CAFL4U(L)/110 CAFL4U(L)/220 – Std. Pk. – – – – – – – 25 25 25 25 CAFL4U(N) 25 Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPCAFL4U 50 EPCAFL4U 50 EPCAFL4U 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA716/2 CA716/3 CA716/4 CA716/10 50 50 50 20 CA716/2 CA716/3 CA716/4 CA716/10 50 50 50 20 CA716/2 CA716/3 CA716/4 CA716/10 50 50 50 20 Current Rating 0.1A 0.2A 0.5A 1.0A 2.0A MT9 Slow Blow Cat. No 0.1M6.3x32T 0.2M6.3x32T 0.5M6.3x32T 1.0M6.3x32T 2.0M6.3x32T 1 Pk. (100 tags) Fast Blow Cat. No 0.1M6x32F 0.2M6x32F 0.5M6x32F 1.0M6x32F 2.0M6x32F MT9 Current Rating 4.0A 5.0A 6.3A 8.0A 10.0A 1 Pk. (100 tags) Slow Blow Cat. No 4.0M6.3x32T 5.0M6.3x32T 6.3M6.3x32T 8.0M6.3x32T 10.0M6.3x32T MT9 Fast Blow Cat. No 4.0M6x32F 5.0M6x32F 6.3M6x32F 8.0M6x32F 10.0M6x32F Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 1 Pk. (100 tags) Ø6.3mm (0.25 in.) 32mm (1.25 in.) 2 pole 3 pole 4 pole 10 pole Marking Tag 22 Cat. No. 25 25 25 Cat. No. External Jumper Fuses 1/4” x 1-1/4” (6.3 x 32mm) Std. Pk. CAFL4U CAFL4U/BU CAFL4U/BL FUSE BLOCKS COMPONENT CARRIER TERMINAL BLOCKS CCC4U SCREW TERMINAL BLOCKS CPF CPFL6-60V CPFL110-240V 27KΩ 27KΩ Dimensions Width 6 mm 6 mm 6 mm 6 mm Length 58.5 mm 28 mm 28 mm 28 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 46 mm 53.5 mm 35 mm 35 mm 35 mm 10.2 g 3.8 g 3.8 g 4.2 g Weight per piece Technical Data/Ratings Approvals 60947-7-1 Wire Size (solid | stranded) 60947-7-1 E220514 60947-7-3 E220514 60947-7-3 E220514 0.2-6 mm2 | 0.2-4 mm2 24-10 AWG 0.2-4 mm2 24-10 AWG 0.2-4 mm2 24-10 AWG 0.2-4 mm2 Voltage Rating 1000 V AC/DC 600 V 1000V AC/DC 600 V 1000V AC/DC 600 V 1000V AC/DC Current Rating * 1A 1A 10 A 10 A 10 A 10 A Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 Component carrier base Plug module with diode Diode Type IN4007 – – Polyamide 66 Carrier Specifications Component Type LED Indicator Voltage Plug module for 5x20 mm fuse Plug module for 5x20 mm fuse with LED indicator – 6-60V AC/DC 110-240V AC/DC Installation Instructions Wire Stripping Length Screwdriver 8 mm 10 mm 10 mm 10 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Terminal Blocks Cat. No. Std. Pk. Grey (standard) CCC4U 50 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Accessories Cat. No. CPF Std. Pk. 50 Cat. No. CPFL6-60V Std. Pk. 50 Cat. No. CPFL110-240V Std. Pk. 50 DIN Rail 2511120 CA701-15/S 20 10 – – – – – – – – – – – – End Stop CA702 CA802 CA103 50 50 50 – – – – – – – – – – – – – – – – – – CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – Internal Jumpers Marking Tag 2 pole 3 pole 4 pole 10 pole 100 pole MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) * Current Rating is based on plug used. Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 23 FUSE HOLDERS FUSE HOLDERS, 10 x 38 mm and CC Type 10x38 Midget Fuse Holders Pole Configuration E212627 Without Indication With LED Indication Fuse Size Max Voltage & Current IEC UL Drawing No. PCF 10 & PCF 10 LED 1-pole 002550001 1-pole+N 002550002 2-pole 002550003 3-pole 002550004 3-pole+N 002550005 002550011 002550012 002550013 002550014 002550015 10x38 10x38 10x38 10x38 10x38 690V AC / 32A 690V AC / 32A 690V AC / 32A 690V AC / 32A 690V AC / 32A 600V AC/DC / 30A 600V AC/DC / 30A 600V AC/DC / 30A 600V AC/DC / 30A 600V AC/DC / 30A 1 1 1 1 1 EFD 10 & EFD 10 LED 1-pole 002540001 1-pole+N 002540002 2-pole 002540003 3-pole 002540004 3-pole+N 002540005 002540011 002540012 002540013 002540014 002540015 10x38 10x38 10x38 10x38 10x38 690V AC/DC / 32A 690V AC/DC / 32A 690V AC/DC / 32A 690V AC/DC / 32A 690V AC/DC / 32A 600V AC/DC / 30A 600V AC/DC / 30A 600V AC/DC / 30A 600V AC/DC / 30A 600V AC/DC / 30A 2 2 2 2 2 Without Indication With LED Indication Fuse Size SCR PCF CC & PCF CC LED 1-pole 002550101 2-pole 002550103 3-pole 002550104 002550111 002550113 002550114 CC Type CC Type CC Type 200 kA 200 kA 200 kA 600V AC/DC / 30A 600V AC/DC / 30A 600V AC/DC / 30A 1 1 1 EFD CC & EFD CC LED 1-pole 002540101 2-pole 002540103 3-pole 002540104 002540111 002540113 002540114 CC Type CC Type CC Type 200 kA 200 kA 200 kA 600V AC / 30A 600V AC / 30A 600V AC / 30A 2 2 2 EFD J30 DC & EFD J30 10 DC LED 1-pole 002570101 002570111 2-pole 002570103 002570113 3-pole 002570104 002570114 J-TYPE J-TYPE J-TYPE 200 kA 200 kA 200 kA 600V AC/DC / 30A 600V AC/DC / 30A 600V AC/DC / 30A 3 3 3 Pole Configuration With LED Indication Fuse Size PCF 10 DC & PCF 10 DC LED 1-pole 002550201 2-pole 002550203 002550211 002550213 10x38 10x38 1000V DC / 25A 1000V DC / 25A 1000V DC / 25A 1000V DC / 25A 1 1 EFH 10 DC & EFH 10 DC LED 1-pole 002540201 2-pole 002540203 002540211 002540213 10x38 10x38 1000V DC / 25A 1000V DC / 25A 1000V DC / 25A 1000V DC / 25A 2 2 EFH 14 DC & EFH 14 DC LED 1-pole 002560201 2-pole 002560203 002560211 002560213 14x51 14x51 1000V DC / 50A 1000V DC / 50A 1000V DC / 50A 1000V DC / 50A 3 3 Pole Configuration Without Indication With LED Indication Fuse Size EFD 14 & EFD 14 LED 1-pole 002560001 1-pole+N 002560002 2-pole 002560003 3-pole 002560004 3-pole+N 002560005 002560011 002560012 002560013 002560014 002560015 14x51 14x51 14x51 14x51 14x51 690V AC / 50A 690V AC / 50A 690V AC / 50A 690V AC / 50A 690V AC / 50A 600V AC/DC / 50A 600V AC/DC / 50A 600V AC/DC / 50A 600V AC/DC / 50A 600V AC/DC / 50A 3 3 3 3 3 EFD 22 & EFD 22 LED 1-pole 002570001 1-pole+N 002570002 2-pole 002570003 3-pole 002570004 3-pole+N 002570005 002570011 002570012 002570013 002570014 002570015 22x58 22x58 22x58 22x58 22x58 690V AC / 100A 690V AC / 100A 690V AC / 100A 690V AC / 100A 690V AC / 100A 600V AC/DC / 100A 600V AC/DC / 100A 600V AC/DC / 100A 600V AC/DC / 100A 600V AC/DC / 100A 4 4 4 4 4 CC Type and J Type Fuse Holders Pole Configuration E212627 UL Rating Voltage/Amp. Drawing No. PV Type Fuse Holders E356295 Without Indication Max Voltage & Current IEC UL Drawing No. E356295 IEC Type Fuse Holders E212627 24 Max Voltage & Current IEC UL Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 Drawing No. FUSE HOLDERS FUSE HOLDERS, 10 x 38 mm and CC Type 1 2 64 43.8 75 17.8 81 37 47.3 6.8 PCF Type EFD10 and EFH10 Type 3 4 83 93 69 69 6.8 43.5 27 6.8 35.6 116.8 120.4 90 94 45 45 43.5 17.5 4 45 83.3 64.4 45.1 59.5 56.8 56.8 EFD 14 Type EFD 22 Type NOTE: All dimensions are shown in millimeters. To convert to inches multiply by 0.03937 Accessories for The Modular Type PCF, EFD and EFH Modular fuse holders have a unique user configurable feature. By using the modular snap kit (parts sold individually) a customer can configure any pole configuration by inserting the connecting element (3 per pole) into the slot in the side of the fuse holder and then pushing them together and inserting the connecting shaft into the handle. Model No. 002559001 002569001 002579001 NOTE: 1 kit suffices for the assembly of 50 sets. 2 Pole Connection Kits Model No. Usable with 002540948 EFD 8, EFD 10, EFH 10, PCF 8, PCF 10, EFD CC, PCF CC 002560948 EFD 14, EFH 14 002570948 EFD 22, EFD J30 Auxiliary Switches Usable with PCF 10 EFD 14 EFD 22 Type 1NO/1NC 1NO/1NC 1NO/1NC For Auxiliary switches to operate, a fuse with striker pin must be used. 3 Pole Connection Kits Model No. Usable with 002540949 EFD 8, EFD 10, PCF 8, PCF 10, EFD CC, PCF CC 002560949 EFD 14 002570949 EFD 22, EFD J30 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 25 DISCONNECT & TEST DISCONNECT AND TEST TERMINAL BLOCKS SCREW TERMINAL BLOCKS CDS6U CDS6U/TS Slider Disconnect Terminal Slider Disconnect Terminal Including Test Sockets Feed Through Terminal with CDS6U profile Width 8 mm 8 mm 6 mm Length 82 mm 82 mm 82 mm 51.0 mm 59.2 mm 51.0 mm 59.2 mm 51.0 mm 59.2 mm 33.8 g 33.8 g 21.2 g CDS6U/FT HIGHLIGHTS FEATURES • Slider Style Disconnect Terminals • CDS6U - Standard Slider Disconnect • CDS6U/TS - Slider Disconnect with integrated testing points • CDS6U/FT - Same profile Feed-Through • Separate Testing points allow insertion of standard test probes • Disconnect is achieved b operating sliding link wit screw driver • SLS2, SLS4 slide shorting link system • QJ8/2 - Shorting Plug APPLICATIONS (see following page) • Disconnect & Test Applications • Measuring / Control Circuits • Utility Instruments an Transformer Applications • Meter Replacement • External Current Measurement • Switch Boards Dimensions & Weight Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Technical Data/Ratings Approvals Wire Size (solid / stranded) 22-8 AWG 0.2-6 mm 600 V 800 V Voltage Rating Current Rating Torque 60947-7-1 E220514 2 60947-7-1 E220514 22-8 AWG 0.2-6 mm 22-8 AWG 0.2-6 mm2 600 V 800 V 600 V 800 V 2 45 A 41 A 45 A 41 A 45 A 41 A 14 lb-in 0.8 Nm 14 lb-in 0.8 Nm 14 lb-in 0.8 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 10 mm 10 mm 10 mm Flat Head 0.8 x 4 mm Flat Head 0.8 x 4 mm Flat Head 0.8 x 4 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W CDS6U CDS6U/R CDS6U/BU CDS6U/BL CDS6U/O CDS6U/G CDS6U/Y CDS6U/W Accessories Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CDS6U/TS CDS6U/TS/R CDS6U/TS/BU CDS6U/TS/BL CDS6U/TS/O CDS6U/TS/G CDS6U/TS/Y CDS6U/TS/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CDS6U/FT CDS6U/FT/R CDS6U/FT/BU CDS6U/FT/BL CDS6U/FT/O CDS6U/FT/G CDS6U/FT/Y CDS6U/FT/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPCDS6U 50 EPCDS6U 50 EPCDS6U 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA723/2 CA723/3 CA723/4 CA723/10 100 50 50 10 CA723/2 CA723/3 CA723/4 CA723/10 100 50 50 10 CA723/2 CA723/3 CA723/4 CA723/10 100 50 50 10 Internal Jumper 26 60947-7-1 E220514 CB SCHEME 2 pole 3 pole 4 pole 10 pole Slide Shorting Link 2 pole 3 pole 4 pole SLS2 SLS3 SLS4 50 25 25 SLS2 SLS3 SLS4 50 25 25 – – – – – – Insulated Test Socket grey red yellow blue black TPSLS TPSLSR TPSLSY TPSLSBU TPSLSBK 100 100 100 100 100 – – – – – – – – – – – – – – – – – – – – Lock Out Cap LCCDS 50 LCCDS 50 – – Shorting Plug QJ8/2 25 QJ8/2 25 – – Marking Tag MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT8 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 1 Pk. (100 tags) DISCONNECT & TEST Example for CDS6U Test & Disconnect Terminal Block Single Phase Current Transformer Test Circuit SCREW TERMINAL BLOCKS 3 Phase current Transformer Test Set LCCDS EPCDS6U EPCDS66 SLS2 CA72315 LCCDS CDS6U SLS2 CA202 CDSGU CA202 Operating status Operating status A 1 2 A 1 A A 2 2 1 3 4 5 6 (with internal distribution of the k-point) S1 S2 S1 S2 S1 S2 S1 S2 SLS2 in open condition SLS2 in open condition L1 L1 Comparison measurement for L1 L2 L3 Comparison measurement for L1 A 1 2 1 Sequence for test : 1) Remove SLS2 screw from terminal 2. 2) Connect ammeter to test sockets of terminal 2. 3) Open disconnect slide link of terminal 2. 2 A A 1 A 2 3 A 4 5 6 2) Connect ammeter to test sockets of terminal 1 and 2. 3) Open disconnect slide link of terminal 1. A S1 S2 S1 SLS2 in open condition L1 Meter test for L1 through external power supply Sequence for test : 1) Remove SLS2 screw from terminal 1. S2 S1 L1 S2 S1 L2 S2 L3 Meter test for L1 through external power supply A 1 2 1 S1 2 Sequence for test : 1) Close short circuit slide SLS2 of terminals 1 and 2. 2) Open disconnect slide link of terminal 2. 3) Connect external power supply to test sockets of terminals 1 and 2. S2 A A A 1 2 3 4 5 6 S1 S2 S1 S2 S1 S2 Sequence for test : 1) Close short circuit slide SLS2 of terminals 1 and 2. 2) Open disconnect slide link of terminal 1. 3) Connect external power supply to test sockets of terminals 1 and 2. Closing of SLS2 L1 L1 L2 L3 Meter Replacement for L1 Meter replacement A 1 1 S1 2 2 Sequence for test : 1) Close short circuit slide SLS2 of terminals 1 and 2. 2) Open disconnect slide link of terminal 2. 3) Disconnect meter for L1 at terminals 1 and 2. S2 A A A 1 2 3 4 5 6 S1 S2 S1 S2 S1 S2 Sequence for test : 1) Close short circuit slide SLS2 of terminals 1 and 2. 2) Open disconnect slide link of terminal 1. 3) Disconnect meter for L1. Closing of SLS2 L1 L1 L2 L3 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 27 DISCONNECT & TEST BLADE/KNIFE STYLE DISCONNECT TERMINAL BLOCKS SCREW TERMINAL BLOCKS CKT4U CKT4U/4 HIGHLIGHTS FEATURES • Knife / Blade Style Disconnect Terminals • CKT4U - Standard Knife Disconnect • CKT4U/4 - 4 Connection Knife Disconnect • Specially designed socket headed screws act as fast monitoring points APPLICATIONS • Disconnect & Test Applications Knife Style Disconnect 2 Connections Dimensions & Weight Knife Style Disconnect 4 Connections Width 6 mm 6 mm Length 46.3 mm 65.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 48.3 mm 56.0 mm 54.3 mm 62.0 mm 10.5 g 16.6 g Weight per piece Technical Data/Ratings Approvals 60947-7-1 E220514 CB SCHEME Wire Size (solid / stranded) Voltage Rating 22-10 AWG 22-10 AWG 0.2-4 mm2 600 V 600 V 60947-7-1 E220514 22-10 AWG 0.2-4 mm2 600 V 800 V 800 V Current Rating 35 A 16 A 28 A 20 A 17.5 A Torque 7 lb-in 7 lb-in 0.5 Nm 7 lb-in 0.5 Nm Insulation Material Polyamide 66 Polyamide 66 8 mm 8 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W CKT4U CKT4U/R CKT4U/BU CKT4U/BL CKT4U/O CKT4U/G CKT4U/Y CKT4U/W Accessories 50 50 50 50 50 50 50 50 Cat. No. CKT4U/4 CKT4U/4/R CKT4U/4/BU CKT4U/4/BL CKT4U/4/O CKT4U/4/G CKT4U/4/Y CKT4U/4/W 50 50 50 50 50 50 50 50 Cat. No. Std. Pk. EPCKT4U 50 EPCKT4U/4 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 CA714/2* CA714/3* CA714/4* CA714/10* 100 100 100 20 Marking Tag 2 pole 3 pole 4 pole 10 pole MT6 1 Pk. (100 tags) Cat. No. Std. Pk. End Plate External Jumper 28 Std. Pk. MT6 Std. Pk. 1 Pk. (100 tags) * Insulated External shorting links can be used only in the upper level clamping unit of the Terminal Block. Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 DISCONNECT & TEST BLADE/KNIFE STYLE DISCONNECT TERMINAL BLOCKS CKT4SP SCREW TERMINAL BLOCKS CF4SP CF4SPFT HIGHLIGHTS FEATURES • Knife Style Disconnect Terminal • CF4SPFT same profile Knife Style Disconnect Feed-Through Terminal Fuse Block Same profile as CF4SP Fuse Block Same profile as CF4SP Fuse Block 5x20 mm Fuse Type Width 6 mm 6 mm 8 mm Length 58.5 mm 58.5 mm 57.0 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 46.0 mm 53.5 mm 46.0 mm 53.5 mm 50.3 mm 57.6 mm 27.2 g g 16.9 g Dimensions & Weight Weight per piece 60947-7-1 E220514 CB SCHEME Wire Size (solid / stranded) 60947-7-1 E220514 Protection • Fused Control Circuits with 60947-7-1 E220514 24-10 AWG 0.2-4 mm2 24-10 AWG 0.2-4 mm2 24-10 AWG 0.2-4 mm2 600 V 1000 V 600 V 1000 V 600 V 1000 V AC/DC Voltage Rating Current Rating Torque 30 A 28 A 30 A 32 A 10 A 10 A 4.5 lb-in 0.5 Nm 4.5 lb-in 0.5 Nm 4.5 lb-in 0.5 Nm Insulation Material Fuse Terminal, 5 x 20 mm Fuse Types APPLICATIONS • Control Systems with Fuse Technical Data/Ratings Approvals Feed Through Terminal • CF4SP same profile as Polyamide 66 Polyamide 66 8 mm 8 mm 8 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm alternating configurations (CF4SP, CF4SPFT, CGT4SP) • Switch Boards Polyamide 66 Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W CKT4SP CKT4SP/R CKT4SP/BU CKT4SP/BL CKT4SP/O CKT4SP/G CKT4SP/Y CKT4SP/W Accessories Cat. No. Std. Pk. 50 50 50 50 50 50 50 50 Std. Pk. Cat. No. CF4SPFT CF4SPFT/R CF4SPFT/BU CF4SPFT/BL CF4SPFT/O CF4SPFT/G CF4SPFT/Y CF4SPFT/W Cat. No. Std. Pk. 50 50 50 50 50 50 50 50 Std. Pk. Cat. No. CF4SP CF4SP/BU CF4SP/BL Cat. No. Std. Pk. 50 50 50 Std. Pk. DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 – – – – – – Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 Insulated Internal Jumper 2 pole 3 pole 4 pole 10 pole 100 pole CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 External Jumper 2 pole 3 pole 4 pole 10 pole CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 Marking Tag MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 29 DISCONNECT & TEST SLIDER STYLE DISCONNECT TERMINAL BLOCKS SCREW TERMINAL BLOCKS CDTTU CDTTUFT CDTTU-SH HIGHLIGHTS FEATURES • Slider Style Disconnect Terminals • CDTTU - Standard Slider Disconnect • CDTTU-SH - Double Disconnect Terminal • CDTTUFT - Same profile • • Feed-Through Specially designed socket headed screws act as fast monitoring points Disconnect is achieved by operating sliding link with screw driver APPLICATIONS • Disconnect & Test Applications Slider Disconnect Terminal Slider Double Disconnect Terminal Feed Through Terminal Slider Disconnect Profile Width 8 mm 16 mm 8 mm Length 63 mm 63 mm 63 mm 58.7 mm 65.7 mm 58.7 mm 65.7 mm 58.7 mm 65.7 mm 28.5 g 59.2 g 27.1 g Dimensions & Weight Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Technical Data/Ratings Approvals E220514 CB SCHEME Wire Size (solid / stranded) 60947-7-1 E220514 16-8 AWG 1.5-10 mm 16-8 AWG 600 V 800 V 300 V Voltage Rating Current Rating Torque 2 60947-7-1 16-8 AWG 1.5-10 300 V mm2 E220514 60947-7-1 16-8 AWG 1.5-10 mm2 600 V 800 V 160 V 41 A 57 A 25 A 25 A 10 A 41 A 57 A 14 lb-in 1.2 Nm 14 lb-in 14 lb-in 1.2 Nm 14 lb-in 1.2 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 12 mm 12 mm 12 mm Flat Head 1.0 x 5.5 mm Flat Head 1.0 x 5.5 mm Flat Head 1.0 x 5.5 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W CDTTU CDTTU/R CDTTU/BU CDTTU/BL CDTTU/O CDTTU/G CDTTU/Y CDTTU/W Accessories 50 50 50 50 50 50 50 50 Cat. No. CDTTU-SH CDTTU-SH/R CDTTU-SH/BU CDTTU-SH/BL CDTTU-SH/O CDTTU-SH/G CDTTU-SH/Y CDTTU-SH/W Std. Pk. 20 20 20 20 20 20 20 20 Cat. No. CDTTUFT CDTTUFT/R CDTTUFT/BU CDTTUFT/BL CDTTUFT/O CDTTUFT/G CDTTUFT/Y CDTTUFT/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPCDTTU 50 EPCDTTU 50 EPCDTTU 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 QJ8/2 25 QJ8/2 25 QJ8/2 25 CA710/2 CA710/3 CA710/4 CA710/10 100 50 50 20 CA710/2 CA710/3 CA710/4 CA710/10 100 50 50 20 CA710/2 CA710/3 CA710/4 CA710/10 100 50 50 20 Shorting Plug QJ8/2 25 – – QJ8/2 25 Marking Tag MT8 1 Pk. (100 tags) 1 Pk. (100 tags) MT8 1 Pk. (100 tags) Shorting Plug External Jumper 30 Std. Pk. 2 pole 2 pole 3 pole 4 pole 10 pole MT8 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 LEVER STYLE DISCONNECT TERMINAL BLOCKS DISCONNECT & TEST SCREW TERMINAL BLOCKS DDDL4U CSDL4U HIGHLIGHTS FEATURES • Lever Style Disconnect Lever Style Disconnect Lever Style Disconnect Bottom Level Feed Through Width 8 mm 8 mm Length 58 mm 88 mm 44.5 mm 52.0 mm 67.4 mm 74.3 mm 15.0 g 27.0 g Dimensions & Weight Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Wire Size (solid / stranded) E220514 60947-7-1 22-10 AWG 0.2-4 mm 600 V 1000 V 600 V 600 V 800 V 14 A - 10 A - 6.3 A 35 A 14 A 32 A 10 A 32 A 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm Voltage Rating Current Rating 60947-7-1 E220514 CB SCHEME Top Bottom Torque Insulation Material 2 Lever Disconnect • DDDL4U - Lever Disconnect with Lower Level Feed-Through • Same profile as CAFL4U APPLICATIONS • Disconnect Applications Technical Data/Ratings Approvals Terminals • CSDL4U - Standard 22-10 AWG 22-10 AWG 0.2-4 mm2 Polyamide 66 Polyamide 66 9.5 mm 9.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W CSDL4U CSDL4U/R CSDL4U/BU CSDL4U/BL CSDL4U/O CSDL4U/G CSDL4U/Y CSDL4U/W Accessories Cat. No. Std. Pk. 100 100 100 100 100 100 100 100 Std. Pk. Cat. No. DDDL4U DDDL4U/R DDDL4U/BU DDDL4U/BL DDDL4U/O DDDL4U/G DDDL4U/Y DDDL4U/W Cat. No. Std. Pk. 20 20 20 20 20 20 20 20 Std. Pk. End Plate EPCSFL4U 50 EPDDFL4U 50 Isolation Partition PPCSFL4U 50 – – DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 50 CA702 CA802 CA202 50 50 50 Internal Jumper 2 pole 3 pole 4 pole 10 pole – – – – – – – – CA729/2 CA729/3 CA729/4 CA729/10 100 50 50 10 Insulated Jumper 2 pole 3 pole 4 pole 10 pole – – – – – – – – CA749/2 CA749/3 CA749/4 CA749/10 100 50 50 10 External Jumper 2 pole 3 pole 4 pole 10 pole CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 20 CA711/2 CA711/3 CA711/4 CA711/10 100 50 50 2 Marking Tag on terminal on lever MT8 MT2 1 Pk. (100 tags) 1 Pk. (100 tags) MT8 MT2 1 Pk. (100 tags) 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 31 DISTRIBUTION SIDE FEED DISTRIBUTION TERMINAL BLOCKS SCREW TERMINAL BLOCKS CDB4/X(1) HIGHLIGHTS FEATURES • Distribution blocks with • • • • • various output configurations Stud/Bolt to secure incoming wire Internally connected terminals Side/center feed versions up to 150A Protective shield for incoming wire APPLICATIONS • Simplified distribution • Width 50A Distribution Terminal Block Side Feed 6 Outputs 8 Outputs 10 Outputs 12 Outputs 14 Outputs 22 Outputs 24 Outputs 52.0 mm 58.0 mm 64.0 mm 70.0 mm 76.0 mm 100.0 mm 106.0 mm Length 43 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 46.2 mm 53.7 mm General Specifications systems Phase distribution application Approvals CB SCHEME • Sum of outgoing wires not to exceed incoming current Higher output currents should be connected close to the input 60947-7-1 E220514 Voltage Rating INSTALLATION  NOTES • Dimensions & Weight 600 V Insulation Material Phase Distribution Application with CDB Terminals 800 V AC/DC Polyamide 66 INPUT Technical Data/Ratings Wire Size (solid / stranded) 10-8 AWG 6-16 mm2 50 A 64 A 26 lb-in 2.0 Nm Current Rating Torque Installation Instructions Wire Stripping Length 8 mm Screwdriver Hex Nut Driver M8 M1 M2 M3 OUTPUT Technical Data/Ratings Wire Size (solid / stranded) 22-10 AWG 0.2-4 mm2 Current Rating 35 A 64 A* Torque 7 lb-in 0.5 Nm Installation Instructions Wire Stripping Length 8 mm Screwdriver Terminal Blocks Grey (standard) 6 Outputs 8 Outputs 10 Outputs 12 Outputs 14 Outputs 22 Outputs 24 Outputs Accessories Flat Head 0.6 x 3.5 mm Cat. No. CDB4/2(1) CDB4/3(1) CDB4/4(1) CDB4/5(1) CDB4/6(1) CDB4/10(1) CDB4/11(1) Cat. No. Std. Pk. 10 10 10 5 5 5 5 Std. Pk. DIN Rail 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 Marking Tag MT6 1 Pk. (100 tags) * Total output current of system 32 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 DISTRIBUTION CENTER FEED DISTRIBUTION TERMINAL BLOCKS Dimensions & Weight Width SCREW TERMINAL BLOCKS CDB10/X CDB25/X CDB4/X CDB6/X 50A Distribution Terminal Block Center Feed 100A Distribution Terminal Block Center Feed 130A Distribution Terminal Block Center Feed 150A Distribution Terminal Block Center Feed 44.0 mm 56.0 mm 68.0 mm 80.0 mm 96.0 mm 108.0 mm 48.0 mm 64.0 mm 80.0 mm 96.0 mm - 72.0 mm 92.0 mm 112.0 mm - 88.0 mm 112.0 mm 136.0 mm - 43 mm 48 mm 48 mm 49 mm 46.2 mm 53.7 mm 47.8 mm 55.5 mm 47.8 mm 55.5 mm 57.2 mm 64.7 mm 4 Outputs 8 Outputs 12 Outputs 16 Outputs 20 Outputs 24 Outputs Length Height w DIN Rail 35 x 7.5 mm 35 x 15 mm General Specifications Approvals 60947-7-1 E220514 CB SCHEME Voltage Rating 600 V 800 V AC/DC 600 V Polyamide 66 Insulation Material 60947-7-1 E220514 60947-7-1 E220514 800 V AC/DC 600 V Polyamide 66 60947-7-1 E220514 800 V AC/DC 600 V Polyamide 66 800 V AC/DC Polyamide 66 INPUT Technical Data/Ratings Wire Size (solid / stranded) 10-8 AWG 6-16 mm2 10-2 AWG 6-25 mm2 8-1/0 AWG 10-35 mm2 6-2/0 AWG 10-50 mm2 50 A 64 A 100 A 82 A 130 A 114 A 150 A 150 A 26 lb-in 2.0 Nm 35 lb-in 3.0 Nm 53 lb-in 6.0 Nm 53 lb-in 6.0 Nm Current Rating Torque Installation Instructions Wire Stripping Length Screwdriver 8 mm 9 mm 11 mm 14 mm Hex Nut Driver M8 Hex Nut Driver M10 Hex Nut Driver M13 Hex Nut Driver M15 OUTPUT Technical Data/Ratings Wire Size (solid / stranded) 22-10 AWG 0.2-4 mm2 22-8 AWG 1.5-6 mm2 22-6 AWG 1.5-10 mm2 12-2 AWG 6-25 mm2 Current Rating (per output) 35 A 32 A 50 A 41 A 65 A 57 A 75 A 75 A Torque 7 lb-in 0.5 Nm 14 lb-in 0.8 Nm 14 lb-in 1.2 Nm 22 lb-in 2.0 Nm Installation Instructions 8 mm 9 mm 11 mm 14 mm Flat Head 0.6 x 3.5 mm Flat Head 0.8 x 4 mm Flat Head 0.8 x 4 mm Flat Head 1.0 x 5.5 mm Wire Stripping Length Screwdriver Terminal Blocks Grey (standard) 4 Outputs 8 Outputs 12 Outputs 16 Outputs 20 Outputs 24 Outputs Accessories Cat. No. Std. Pk. Cat. No. Std. Pk. CDB4/1 CDB4/2 CDB4/3 CDB4/4 CDB4/5 CDB4/6 10 10 10 10 5 5 CDB6/1 CDB6/2 CDB6/3 CDB6/4 - 10 10 10 5 - Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. CDB10/2 CDB10/3 CDB10/4 Cat. No. Std. Pk. 10 10 5 Std. Pk. Cat. No. CDB25/1 CDB25/2 CDB25/3 CDB25/4 Cat. No. Std. Pk. 10 10 10 5 Std. Pk. DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 Marking Tag MT6 1 Pk. (100 tags) MT10 1 Pk. (100 tags) MT12 1 Pk. (100 tags) 1 Pk. (100 tags) MT8 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 33 DISTRIBUTION MULTI I/O DISTRIBUTION TERMINAL BLOCKS SCREW TERMINAL BLOCKS CMDB4/X Dimensions Width CMDB6/X CMDB10/X CMDB25/X 35 A Distribution Terminal Block 50 A Distribution Terminal Block 65 A Distribution Terminal Block 85 A Distribution Terminal Block 13.5 mm 19.5 mm 25.5 mm 61.5 mm 17.5 mm 25.5 mm 33.5 mm 81.5 mm 21.5 mm 31.5 mm 41.5 mm 101.5 mm 26.0 mm 38.0 mm 50.0 mm 62.0 mm 43 mm 48 mm 48 mm 49 mm 46.2 mm 53.7 mm 47.8 mm 55.5 mm 47.8 mm 55.5 mm 57.2 mm 64.7 mm 2 pole 3 pole 4 pole 10 pole Length Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Technical Data/Ratings Approvals 60947-7-1 E220514 CB SCHEME Wire Size (solid / stranded) 22-10 AWG 0.2-4 mm 600 V 1000V AC/DC Voltage Rating 2 60947-7-1 E220514 60947-7-1 E220514 60947-7-1 E220514 22-8 AWG 1.5-6 mm 22-6 AWG 1.5-10 mm 12-4 AWG 6.0-25 mm2 600 V 1000V AC/DC 600 V 1000V AC/DC 600 V 800V AC/DC 2 2 Current Rating 35 A 32 A 50 A 41 A 65 A 57 A 85 A 101 A Torque 7 lb-in 0.5 Nm 14 lb-in 0.8 Nm 14 lb-in 1.2 Nm 22 lb-in 2.0 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 Polyamide 66 Installation Instructions Wire Stripping Length Screwdriver 8 mm 9 mm 11 mm 14 mm Flat Head 0.6 x 3.5 mm Flat Head 0.8 x 4 mm Flat Head 0.8 x 4 mm Flat Head 1.0 x 5.5 mm Terminal Blocks 4 Outputs Grey (standard) Red R Blue BU Black BL 6 Outputs Grey (standard) Red R Blue BU Black BL 8 Outputs Grey (standard) Red R Blue BU Black BL 20 Outputs Grey (standard) Red R Blue BU Black BL Accessories 34 Cat. No. CMDB4/2 CMDB4/2/R CMDB4/2/BU CMDB4/2/BL Cat. No. CMDB4/3 CMDB4/3/R CMDB4/3/BU CMDB4/3/BL Cat. No. CMDB4/4 CMDB4/4/R CMDB4/4/BU CMDB4/4/BL Cat. No. CMDB4/10 CMDB4/10/R CMDB4/10/BU CMDB4/10/BL Cat. No. Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. Cat. No. CMDB6/2 CMDB6/2/R CMDB6/2/BU CMDB6/2/BL Cat. No. CMDB6/3 CMDB6/3/R CMDB6/3/BU CMDB6/3/BL Cat. No. CMDB6/4 CMDB6/4/R CMDB6/4/BU CMDB6/4/BL Cat. No. CMDB6/10 CMDB6/10/R CMDB6/10/BU CMDB6/10/BL Cat. No. Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. Cat. No. CMDB10/2 CMDB10/2/R CMDB10/2/BU CMDB10/2/BL Cat. No. CMDB10/3 CMDB10/3/R CMDB10/3/BU CMDB10/3/BL Cat. No. CMDB10/4 CMDB10/4/R CMDB10/4/BU CMDB10/4/BL Cat. No. CMDB10/10 CMDB10/10/R CMDB10/10/BU CMDB10/10/BL Cat. No. Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. 5 5 5 5 Std. Pk. Cat. No. CMDB25/2 CMDB25/2/R CMDB25/2/BU CMDB25/2/BL Cat. No. CMDB25/3 CMDB25/3/R CMDB25/3/BU CMDB25/3/BL Cat. No. CMDB25/4 CMDB25/4/R CMDB25/4/BU CMDB25/4/BL Cat. No. CMDB25/10 CMDB25/10/R CMDB25/10/BU CMDB25/10/BL Cat. No. Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. 10 10 10 10 Std. Pk. DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 Marking Tag MT6 1 Pk. (100 tags) MT10 1 Pk. (100 tags) MT12 1 Pk. (100 tags) 1 Pk. (100 tags) MT8 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 COMPACT HYBRID DISTRIBUTION TERMINAL BLOCKS CXDB35/10 DISTRIBUTION SPRING TERMINAL BLOCKS CXDB35/10A HIGHLIGHTS with Allen Screw 1 Flat Head Screw Input 4 Spring Clamp Outputs 1 Hex Screw Input 4 Spring Clamp Outputs Width 16 mm 16 mm Length 81.6 mm 81.6 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 46.8 mm 54.3 mm 46.8 mm 54.3 mm 53.2 g 53.2 g Dimensions & Weight Weight per piece CB SCHEME 60947-7-1 E220514 60947-7-1 600 V 1000V AC/DC 600 V 1000V AC/DC Insulation Material Polyamide 66 (4 x41A) • Modular system • Standard slot & hex screw versions • Expandable with standard CX Series APPLICATIONS • Miniature Circuit Breaker (MCB) E220514 Voltage Rating Terminal Block • Screw input (115A) • 4 spring clamp outputs jumpers and terminal blocks • Easy Installation General Specifications Approvals FEATURES • Hybrid Distribution distribution • Limited space distribution Polyamide 66 Output Expansion CXDB35/10A INPUT Technical Data/Ratings Wire Size (solid / stranded) 14-2 AWG 1.5-35 mm2 14-2 AWG 1.5-35 mm2 Current Rating 115 A 125 A 115 A 125 A Torque 25 lb-in 2.5 Nm 25 lb-in 2.5 Nm Installation Instructions Terminal Blocks (see page 64) Wire Stripping Length Screwdriver 2 x CX6 17 mm 17 mm Flat Head 1.0 x 5.5 mm Hex Screw M5 JX6/3 OUTPUT Technical Data/Ratings Wire Size (solid / stranded) 24-8 AWG 0.2-10 mm2 24-8 AWG 0.2-10 mm2 41 A 41 A 41 A 41 A Current Rating MCB Distribution Example Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Grey Accessories 15 mm 15 mm Flat Head 0.8 x 4 mm Flat Head 0.8 x 4 mm Cat. No. CXDB35/10 Cat. No. Std. Pk. 20 Std. Pk. Cat. No. CXDB35/10A Cat. No. Std. Pk. 20 Std. Pk. DIN Rail 2511120 CA701-15/S 20 20 2511120 CA701-15/S 20 20 End Clamp CA702 CA802 CA103 50 50 50 CA702 CA802 CA103 50 50 50 Jumpers JX6/2 JX6/3 JX6/4 JX6/10 100 50 50 10 JX6/2 JX6/3 JX6/4 JX6/10 100 50 50 10 Marking Tag MT16 1 Pk. (100 tags) MT16 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 35 DISTRIBUTION GROUNDING NEUTRAL CLAMPS GROUNDING SYSTEM CENC4 CENC35 CENC16 HIGHLIGHTS FEATURES • 3 Clamp Sizes • Panel Mount •NES •NEB6 • DIN Rail Mount •CA202 •NEB10 • Tin Plated Copper Busbars • Busbar Current rating 140A Standard Color: Green Dimensions & Weight Width 7.5 mm 9.8 mm 14.5 mm Length 23.3 mm 23.3 mm 27.3 mm 8g 10.5 g 20 g Weight per piece Technical Data/Ratings Approvals E220514 CB SCHEME • Various colors Wire Size (solid / stranded) APPLICATIONS • Grounding Solution • Terminating Neutral an Torque • Voltage Rating 60947-7-2 E220514 60947-7-2 E220514 60947-7-2 22-12 AWG 22-12 AWG 0.2-6 mm2 10-6 AWG 10-6 AWG 10-16 mm2 8-2 AWG 8-2 AWG 10-35 mm2 600 V Current Rating Grounding Wires to a single busbar Distribution Applications 600 V 800 V 600 V 600 V 800 V 600 V 800 V - - 37 A - - 76 A - - 125 A 14 lb-in 14 lb-in 0.8 Nm 17.5 lb-in 17.5 lb-in 2.0 Nm 25 lb-in 25 lb-in 2.5 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 12 mm 16 mm 16 mm Flat Head 0.8 x 4 mm Flat Head 1.0 x 5.5 mm Flat Head 1.0 x 5.5 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Green (standard) Black BL Blue BU Grey GR Yellow Y Std. Pk. CENC4 CENC4/BL CENC4/BU CENC4/GR CENC4/Y Mounting Accessories Panel Mount Cat. No. 50 50 50 50 50 Std. Pk. Cat. No. Std. Pk. CENC16 CENC16/BL CENC16/BU CENC16/GR CENC16/Y 50 50 50 50 50 Cat. No. Std. Pk. Cat. No. Std. Pk. CENC35 CENC35/BL CENC35/BU CENC35/GR CENC35/Y 50 50 50 50 50 Cat. No. Std. Pk. Busbar (6 x 6 mm) NEB6 1m NEB6 1m NEB6 1m Plastic Support with Fixing Screw NES 50 NES 50 NES 50 Marking Tag MT5 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) Mounting Accessories DIN Rail Mount Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Busbar (10 x 3 mm) NEB10 1m NEB10 1m NEB10 1m End Clamp/Busbar support for rail mounting CA202 50 CA202 50 CA202 50 Marking Tag MT5 1 Pk. (100 tags) MT6 1 Pk. (100 tags) MT6 1 Pk. (100 tags) Panel Mount DIN Rail Mount Assembly Example Assembly Example CENC16 NEB10 Busbar CENC4 CENC16 NEB6 Busbar NES Plastic Support 36 600 V CA202 Mounting Support Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 HIGH VOLTAGE HIGH VOLTAGE TERMINAL BLOCKS SCREW TERMINAL BLOCKS CHV4U CHV6U CHV10U HIGHLIGHTS FEATURES • High Voltage Terminal Blocks Dimensions & Weight Width 6 mm 8 mm 10 mm Length 52 mm 52 mm 52 mm 63.4 mm 70.8 mm 63.4 mm 70.8 mm 63.4 mm 70.8 mm 11.0 g 16.0 g 21.6 g Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece • 1000V UL Rating • 1500V IEC DC Rating • Same Profile on all Current Ratings Technical Data/Ratings Approvals 60947-7-1 E220514 CB SCHEME Wire Size (solid / stranded) 22-10 AWG 0.2-4 mm 1000 V 1500 V AC/DC Voltage Rating 2 60947-7-1 E220514 22-8 AWG 0.2-6 mm 1000 V 1500 V AC/DC 2 60947-7-1 E220514 20-6 AWG 0.2-10 mm2 1000 V 1500 V AC/DC Current Rating 35 A 32 A 50 A 41 A 65 A 57 A Torque 7 lb-in 0.5 Nm 14 lb-in 0.8 Nm 14 lb-in 1.2 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 12 mm 14 mm 14 mm Flat Head 0.6 x 3.5 mm Flat Head 0.8 x 4 mm Flat Head 0.8 x 4 mm APPLICATIONS • Solar Applications • High Voltage Applications Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W CHV4U CHV4U/R CHV4U/BU CHV4U/BL CHV4U/O CHV4U/G CHV4U/Y CHV4U/W Accessories Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CHV6U CHV6U/R CHV6U/BU CHV6U/BL CHV6U/O CHV6U/G CHV6U/Y CHV6U/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CHV10U CHV10U/R CHV10U/BU CHV10U/BL CHV10U/O CHV10U/G CHV10U/Y CHV10U/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPUSC 50 EPUSC 50 EPUSC 50 Separator Plate SP2.5/4UN 50 SP2.5/4UN 50 SP2.5/4UN 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA702 CA802 CA202 50 50 25 CA623/2 CA623/3 CA623/4 CA623/10 100 100 100 10 CA624/2 CA624/3 CA624/4 CA624/10 100 100 100 10 CA625/2 CA625/3 CA625/4 CA625/10 100 100 100 10 Internal Jumper Marking Tag 2 pole 3 pole 4 pole 10 pole 100 pole MT6 1 Pk. (100 tags) MT8 1 Pk. (100 tags) MT10 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 37 THERMOCOUPLE THERMOCOUPLE BLOCKS SCREW TERMINAL BLOCKS CTT2.5UK/J/T/E HIGHLIGHTS FEATURES • Thermocouple terminal • • • blocks are used to extend thermocouple compensating lines in measuring circuits The current bar of the terminal block is made of the same material as the thermocouple wire (As per EN 60584/DINEN 60584) No loss of potential at the connection points Available types: K Type - Chromel (NiCr), Alumel (Ni) J Type - Iron (Fe), Constantan (CuNi) T Type - Copper (Cu), Constantan (CuNi) E Type - Chromel (NiCr), Constantan (CuNi) APPLICATIONS • Measurement applications CTT2.5UX Dimensions & Weight Width 10 mm Length 43 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 46.2 mm 53.7 mm Weight per piece 12.4 g Technical Data/Ratings Approvals 60947-7-1 CB SCHEME Wire Size (solid / stranded) 22-14 AWG 0.2-2.5 mm2 Voltage Rating 1000 V AC/DC Current Rating 10 A Torque 7 lb-in / 0.4 Nm Insulation Material Polyamide 66 Installation Instructions Wire Stripping Length 8 mm Screwdriver Flat Head 0.5 x 3 mm Terminal Blocks Grey U Type J Type T Type G Type Accessories Cat. No. Std. Pk. CTT2.5UK CTT2.5UJ CTT2.5UT CTT2.5UG 50 50 50 50 Cat. No. Std. Pk. End Plate EP2.5/4UN 50 Partition Plate PP2.5/4UN 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 100 100 Marking Tag INCLUDED Typical Temperature Measuring Circuit Thermocouple Terminal Block Compensating Cable Supply Cable Thermocouple (Sensor) Measuring Instrument Thermocouple Terminal Block 38 Reference Junction Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 TAB CONNECTION TERMINAL BLOCKS TAB CONNECTION SCREW TERMINAL BLOCKS CTC4U HIGHLIGHTS FEATURES • Standard tab connection terminals Dimensions & Weight Width 6 mm Length 47 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm • Quick-Connect Tabs 51.2 mm 58.8 mm Weight per piece APPLICATIONS • Transportation • Railroad Applications 8.0 g Technical Data/Ratings Approvals 60947-7-1 CB SCHEME Wire Size (solid | stranded) 0.2-4.0 mm2 | 24-12 AWG Voltage Rating 300 V Current Rating 32 A Tab (Blade) Size 6.3 x 0.8 mm Insulation Material Polyamide 66 Installation Instructions Wire Stripping Length Terminal Blocks Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W Accessories 9 mm Cat. No. CTC4U CTC4U/R CTC4U/BU CTC4U/BL CTC4U/O CTC4U/G CTC4U/Y CTC4U/W Std. Pk. 100 100 100 100 100 100 100 100 Cat. No. Std. Pk. End Plate EPCTC4U 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 100 100 Test Socket CA707/TS/01 Marking Tag MT6 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 39 SPRING LOADED FEED-THROUGH TERMINAL BLOCKS SCREW TERMINAL BLOCKS CTS4USC CTS6USC CTS10USC HIGHLIGHTS FEATURES • Feed Through Terminals with Springs below clamps • High torque screws • Built-in springs guarantee • • • • secure connection even when screw is not tight 4 mm, 6 mm, 10mm terminal blocks with same size profile It is recommended to use hook type lugs/ ferrules for wire termination Both, high-torque screws and built-in spring Various disconnect terminals APPLICATIONS • Vibration Applications • Projects which follow the following safety regulations: • Electric Supply Standard (ESI) • British CEGB Standard • NTPC standard Feed Through Terminal Spring Loaded Feed Through Terminal Spring Loaded Width 6 mm 8 mm 10 mm Length 52 mm 52 mm 52 mm 63.4 mm 70.8 mm 63.4 mm 70.8 mm 63.4 mm 70.8 mm 13.0 g 10.0 g 12.6 g Height w DIN Rail 35 x 7.5 mm 35 x 15 mm Weight per piece Technical Data/Ratings Approvals 60947-7-1 E220514 CB SCHEME Wire Size (solid / stranded) 60947-7-1 E220514 60947-7-1 E220514 22-10 AWG 0.2-4 mm2 22-8 AWG 0.2-6 mm2 20-6 AWG 0.2-10 mm2 600 V 1500V AC/DC 1000 V 1500V AC/DC 1000 V 1500V AC/DC Voltage Rating Current Rating 35 A 32 A 50 A 41 A 65 A 57 A Torque 7 lb-in 0.5 Nm 14 lb-in 0.8 Nm 14 lb-in 1.2 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 12 mm 14 mm 14 mm Flat Head 0.6 x 3.5 mm Flat Head 0.8 x 4 mm Flat Head 0.8 x 4 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W CTS4USC CTS4USC/R CTS4USC/BU CTS4USC/BL CTS4USC/O CTS4USC/G CTS4USC/Y CTS4USC/W Accessories Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CTS6USC CTS6USC/R CTS6USC/BU CTS6USC/BL CTS6USC/O CTS6USC/G CTS6USC/Y CTS6USC/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CTS10USC CTS10USC/R CTS10USC/BU CTS10USC/BL CTS10USC/O CTS10USC/G CTS10USC/Y CTS10USC/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate EPUSC 50 EPUSC 50 EPUSC 50 Separator Plate SP2.5/4UN 50 SP2.5/4UN 50 SP2.5/4UN 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 100 50 50 CA702 CA802 CA202 100 50 50 CA702 CA802 CA202 100 50 50 1.5 mm2 2.5 mm2 4 mm2 6 mm2 10 mm2 CA604/1 CA604/2 CA604/5 – – 100 100 100 – – CA604/1 CA604/2 CA604/5 CA604/4 – 100 100 100 100 – CA604/1 CA604/2 CA604/5 CA604/4 CA604/3 100 100 100 100 100 2 pole 3 pole 4 pole 10 pole CA623/2 CA623/3 CA623/4 CA623/10 100 100 100 10 CA624/2 CA624/3 CA624/4 CA624/10 MT8 Hook Type Lug / Ferrule Pre Assembled Jumpers Marking Tag 40 Feed Through Terminal Spring Loaded Dimensions & Weight MT6 1 Pk. (100 tags) 100 100 100 10 1 Pk. (100 tags) CA625/2 CA625/3 CA625/4 CA625/10 MT10 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 100 100 100 10 1 Pk. (100 tags) SPRING LOADED DISCONNECT TERMINAL BLOCKS SCREW TERMINAL BLOCKS Knife Disconnect Spring Loaded Terminal Dimensions & Weight CDTTUSC CDS6U/SC CKT4SPSC Slider Disconnect Spring Loaded Terminal CDTTUFTSC Slider Disconnect Spring Loaded Terminal Feed Through Terminal Same profile as CDTTUSC Width 6 mm 8 mm 8 mm 8 mm Length 58.5 mm 82 mm 63 mm 63 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 46.0 mm 53.5 mm 51.0 mm 59.2 mm 58.7 mm 65.7 mm 58.7 mm 65.7 mm 14.1 g 30.9 g 31.0 g 25.4 g Weight per piece Technical Data/Ratings Approvals 60947-7-1 E220514 CB SCHEME Wire Size (solid / stranded) 60947-7-1 E220514 60947-7-1 E220514 60947-7-1 E220514 24-10 AWG 0.2-4 mm2 22-8 AWG 0.2-6 mm2 16-8 AWG 1.5-10 mm2 16-8 AWG 1.5-10 mm2 600 V 1000V AC/DC 600 V 800V AC/DC 600 V 800V AC/DC 600 V 800V AC/DC Voltage Rating Current Rating Torque 30 A 28 A 45 A 41 A 41 A 57 A 41 A 57 A 4.5 lb-in 0.5 Nm 14 lb-in 0.8 Nm 14 lb-in 1.2 Nm 14 lb-in 1.2 Nm Insulation Material Polyamide 66 Polyamide 66 Polyamide 66 Polyamide 66 8 mm 10 mm 12 mm 12 mm Flat Head 0.6 x 3.5 mm Flat Head 0.8 x 4 mm Flat Head 1.0 x 5.5 mm Flat Head 1.0 x 5.5 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey (standard) Red R Blue BU Black BL Orange O Green G Yellow Y White W CKT4SPSC CKT4SPSC/R CKT4SPSC/BU CKT4SPSC/BL CKT4SPSC/O CKT4SPSC/G CKT4SPSC/Y CKT4SPSC/W Accessories Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CDS6U/SC CDS6U/SC/R CDS6U/SC/BU CDS6U/SC/BL CDS6U/SC/O CDS6U/SC/G CDS6U/SC/Y CDS6U/SC/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. CDTTUSC CDTTUSC/R CDTTUSC/BU CDTTUSC/BL CDTTUSC/O CDTTUSC/G CDTTUSC/Y CDTTUSC/W Std. Pk. 50 50 50 50 50 50 50 50 Cat. No. Std. Pk. CDTTUFTSC CDTTUFTSC/R CDTTUFTSC/BU CDTTUFTSC/BL CDTTUFTSC/O CDTTUFTSC/G CDTTUFTSC/Y CDTTUFTSC/W 50 50 50 50 50 50 50 50 Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. End Plate – – EPCDS6U 50 EPCDTTU 50 EPCDTTU 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 CA202 100 50 50 CA702 CA802 CA202 100 50 50 CA702 CA802 CA202 100 50 50 CA702 CA802 CA202 100 50 50 100 50 50 10 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – Cat. No. Pre Assembled Jumpers 2 pole 3 pole 4 pole 10 pole 100 pole CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 100 100 100 10 10 CA723/2 CA723/3 CA723/4 CA723/10 – Insulated Jumpers 2 pole 3 pole 4 pole 10 pole 100 pole CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 100 100 100 10 10 – – – – – – – – – – – – – – – External Jumpers 2 pole 3 pole 4 pole 10 pole CA714/2 CA714/3 CA714/4 CA714/10 100 100 100 20 – – – – – – – – CA710/2 CA710/3 CA710/4 CA710/10 100 50 50 20 CA710/2 CA710/3 CA710/4 CA710/10 – – – QJ8/2 25 – Shorting Plug – Marking Tag MT6 1 Pk. (100 tags) MT8 1 Pk. (100 tags) MT8 1 Pk. (100 tags) MT8 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 100 50 50 20 – 1 Pk. (100 tags) 41 ELECTRONIC COMPONENTS DIODE CIRCUIT TERMINAL BLOCKS SCREW TERMINAL BLOCKS CDL4U(E)D1/D2 CDL4U(E)D3 CDL4U(E)DD1/DD2 HIGHLIGHTS FEATURES • Various configurations of • • • • Electronic components soldered into CDL4U double level terminal block Various Diode / Resistor combinations 4 connection points for convenient wiring Terminal Block with open current bar CDL4U(O) can be individually soldered with electronic components Spacer CDL4USP can be used to cover overlapping components when soldered individually APPLICATIONS • Reverse polarity protection • Lamp testing 1 2 1 3 4 2 1 3 +4 CDL4U(E)DD1 CDL4U(E)D1 1 2 CDL4U(E)D3 4 3 -4 CDL4U(E)D2 Dimensions & Weight 2 1 4 3 3 2 CDL4U(E)DD2 Arc Suppression circuit diode for contactors and solenoid valves Diode reverse polarity protection Diode circuit for lamp testing Width 6 mm 6 mm 6 mm Length 55.5 mm 55.5 mm 55.5 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 13.6 g 13.4 g 13.4 g Weight per piece Technical Data/Ratings Approvals CB SCHEME Wire Size (solid / stranded) E220514 60947-7-1 22-10 AWG 0.2-4 mm2 E220514 60947-7-1 22-10 AWG 0.2-4 mm2 E220514 60947-7-1 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 300 V 500 V AC 600 V 300 V 500 V AC 600 V 300 V 500 V AC Current Rating 35 A 25 A 32 A 35 A 25 A 32 A 35 A 25 A 32 A Torque 7 lb-in Insulation Material 0.5 Nm 7 lb-in Polyamide 66 0.5 Nm 7 lb-in Polyamide 66 0.5 Nm Polyamide 66 Electronic Component Specifications Diode Type 1N 4007 1N 4007 1N 4007 1000 V / 1 A 1000 V / 1 A 1000 V / 1 A - - - 9 mm 9 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Diode Reverse Voltage / Current Indicator Voltage Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey CDL4U(E)D1 CDL4U(E)D2 Spacer to cover electronic components which stick out of CDL4U(O) Cat. No. CDL4USP 42 Std. Pk. 100 100 Cat. No. CDL4U(E)D3 Std. Pk. 100 Cat. No. CDL4U(E)DD1 CDL4U(E)DD2 Std. Pk. 100 100 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. End Plate EPCDL4U 50 EPCDL4U 50 EPCDL4U 50 Spacer CDL4USP 50 CDL4USP 50 CDL4USP 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 Accessories CDL4U SPACER Std. Pk. Internal Jumper Marking Tag 2 pole 3 pole 4 pole 10 pole MT2 1 Pk. (100 tags) MT2 1 Pk. (100 tags) MT2 50 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 Std. Pk. 1 Pk. (100 tags) ELECTRONIC COMPONENTS DIODE CIRCUIT TERMINAL BLOCKS SCREW TERMINAL BLOCKS CDL4U(E)DD3/DD4 1 CDL4U(E)D4 CDL4U(E)DD5 2 +3 +4 1 1 2 2 CDL4U(E)DD3 1 2 3 3 +4 CDL4U(E)D4 +3 +4 CDL4U(E)DD5 +4 CDL4U(E)DD4 Diode circuit for lamp testing Dimensions & Weight Diode circuit for lamp testing with LED series resistance Diode circuit for lamp testing with LED series resistance Width 6 mm 6 mm 6 mm Length 55.5 mm 55.5 mm 55.5 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 13.6 g 13.6 g 13.6 g Weight per piece Technical Data/Ratings Approvals CB SCHEME Wire Size (solid / stranded) E220514 60947-7-1 22-10 AWG 0.2-4 mm2 E220514 60947-7-1 22-10 AWG 0.2-4 mm2 E220514 60947-7-1 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 300 V 500 V AC 600 V 300 V 500 V AC 600 V 300 V 500 V AC Current Rating 35 A 25 A 32 A 35 A 25 A 32 A 35 A 25 A 32 A Torque 7 lb-in Insulation Material 0.5 Nm 7 lb-in Polyamide 66 0.5 Nm 7 lb-in Polyamide 66 0.5 Nm Polyamide 66 Electronic Component Specifications Diode Type 1N 4007 1N 4007 1N 4007 1000 V / 1 A 1000 V / 1 A 1000 V / 1 A - - - 9 mm 9 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Diode Reverse Voltage / Current Indicator Voltage Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Cat. No. Grey CDL4U(E)DD3 CDL4U(E)DD4 Accessories Std. Pk. 100 100 Cat. No. Std. Pk. CDL4U(E)D4/12V CDL4U(E)D4/24V 100 100 Cat. No. Std. Pk. CDL4U(E)DD5/12V CDL4U(E)DD5/24V 100 100 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. End Plate EPCDL4U 50 EPCDL4U 50 EPCDL4U 50 Spacer CDL4USP 50 CDL4USP 50 CDL4USP 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 Internal Jumper Marking Tag 2 pole 3 pole 4 pole 10 pole MT2 1 Pk. (100 tags) MT2 1 Pk. (100 tags) MT2 Std. Pk. 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 43 ELECTRONIC COMPONENTS INDICATOR TERMINAL BLOCKS SCREW TERMINAL BLOCKS CDL4U(E)N1 CDL4U(E)LD5 CDL4U(E)LD3 HIGHLIGHTS FEATURES • Various configurations of • • • • • • • Electronic components soldered into CDL4U double level terminal block Various Indicator options AC voltage indicator DC voltage indicator LED and Neon lamp versions 4 connection points for convenient wiring Terminal Block with open current bar CDL4U(O) can be individually soldered with electronic components Spacer CDL4USP can be used to cover overlapping components when soldered individually APPLICATIONS • AC voltage indication • DC voltage indication 1 2 +1 1 3 4 3 4 3 CDL4U(E)N1 CDL4U(E)LD5 -4 CDL4U(E)LD3 AC Voltage indicator with Neon lamp AC Voltage indicator with LED AC Voltage indicator with LED Width 6 mm 6 mm 6 mm Length 55.5 mm 55.5 mm 55.5 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 13.6 g 12.4 g 12.4 g Dimensions & Weight Weight per piece Technical Data/Ratings Approvals CB SCHEME Wire Size (solid / stranded) E220514 60947-7-1 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 300 V Current Rating 35 A 25 A Torque 60947-7-1 22-10 AWG 0.2-4 mm2 500 V AC 600 V 300 V 32 A 35 A 25 A 7 lb-in Insulation Material E220514 0.5 Nm 60947-7-1 22-10 AWG 0.2-4 mm2 500 V AC 600 V 300 V 32 A 35 A 25 A 7 lb-in Polyamide 66 E220514 0.5 Nm 500 V AC 32 A 7 lb-in 0.5 Nm Polyamide 66 Polyamide 66 1N 4007 1N 4007 Electronic Component Specifications Diode Type 1N 4007 Diode Reverse Voltage / Current 1000 V / 1 A 1000 V / 1 A 1000 V / 1 A Indicator Voltage 110, 220 VAC 24, 48, 110, 220 VAC 12, 24 VAC Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks 9 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Cat. No. Grey Std. Pk. CDL4U(E)N1/110V CDL4U(E)N1/220V Accessories 100 100 Cat. No. Std. Pk. CDL4U(E)LD5/24V CDL4U(E)LD5/48V CDL4U(E)LD5/110V CDL4U(E)LD5/220V 100 100 100 100 Cat. No. Std. Pk. CDL4U(E)LD3/12V CDL4U(E)LD3/24V 100 100 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. End Plate EPCDL4U 50 EPCDL4U 50 EPCDL4U 50 Spacer CDL4USP 50 CDL4USP 50 CDL4USP 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 Internal Jumper Marking Tag 44 9 mm Flat Head 0.6 x 3.5 mm 2 pole 3 pole 4 pole 10 pole MT2 1 Pk. (100 tags) MT2 1 Pk. (100 tags) MT2 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 Std. Pk. 1 Pk. (100 tags) ELECTRONIC COMPONENTS INDICATOR TERMINAL BLOCKS CDL4U(E)LD1/LD2 SCREW TERMINAL BLOCKS CDL4U(E)LD4 CDL4U(O) CDL4U(E)L1/L2 +1 +1 -3 -1 +4 -3 CDL4U(E)LD1 -4 CDL4U(E)L1 +3 -1 +3 +1 +4 CDL4U(E)LD4 +4 -3 CDL4U(E)LD2 CDL4U(O) -4 CDL4U(E)L2 DC Voltage Indicator with LED AC Voltage indicator with LED DC Voltage Indicator with LED Terminal Block with open current to solder custom components Width 6 mm 6 mm 6 mm 6 mm Length 55.5 mm 55.5 mm 55.5 mm 55.5 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 12.4 g 12.4 g 12.4 g 13.0 g Dimensions & Weight Weight per piece Technical Data/Ratings Approvals CB SCHEME Wire Size (solid / stranded) E220514 60947-7-1 22-10 AWG 0.2-4 mm2 E220514 60947-7-1 22-10 AWG 0.2-4 mm2 E220514 60947-7-1 22-10 AWG 0.2-4 mm2 E220514 60947-7-1 22-10 AWG 0.2-4 mm2 Voltage Rating 600 V 300 V 500 V AC 600 V 300 V 500 V AC 600 V 300 V 500 V AC 600 V 300 V 500 V AC Current Rating 35 A 25 A 32 A 35 A 25 A 32 A 35 A 25 A 32 A 35 A 35 A 32 A Torque 7 lb-in Insulation Material 0.5 Nm 7 lb-in Polyamide 66 7 lb-in 0.5 Nm 0.5 Nm 7 lb-in 0.5 Nm Polyamide 66 Polyamide 66 Polyamide 66 1N 4007 1N 4007 1N 4007 1N 4007 Diode Reverse Voltage / Current 1000 V / 1 A 1000 V / 1 A 1000 V / 1 A 1000 V / 1 A Indicator Voltage 12, 24 VAC 24, 48 VAC 6, 24 VAC - 9 mm 9 mm 9 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Electronic Component Specifications Diode Type Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Std. Pk. Cat. No. Grey CDL4U(E)LD1/12V CDL4U(E)LD1/24V CDL4U(E)LD2/12V CDL4U(E)LD2/24V Accessories 100 100 100 100 Cat. No. Std. Pk. CDL4U(E)LD4/24V CDL4U(E)LD4/48V 100 100 CDL4U(E)L1/6V CDL4U(E)L1/24V CDL4U(E)L2/6V CDL4U(E)L2/24V Cat. No. 100 100 100 100 CDL4U(O) Cat. No. Std. Pk. Cat. No. Std. Pk. 100 Cat. No. Std. Pk. Cat. No. End Plate EPCDL4U 50 EPCDL4U 50 EPCDL4U 50 EPCDL4U 50 Spacer CDL4USP 50 CDL4USP 50 CDL4USP 50 CDL4USP 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 CA727/2 CA727/3 CA727/4 CA727/10 100 100 100 10 Internal Jumper Marking Tag 2 pole 3 pole 4 pole 10 pole MT2 1 Pk. (100 tags) MT2 Std. Pk. Std. Pk. Cat. No. 1 Pk. (100 tags) MT2 1 Pk. (100 tags) MT2 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 Std. Pk. 1 Pk. (100 tags) 45 ELECTRONIC COMPONENTS SURGE SUPPRESSOR TERMINAL BLOCKS SCREW TERMINAL BLOCKS CDL4U(E)LA CDL4U(E)3LA CDL4U(E)RC CDL4U(E)3LA CDL4U(E)RC HIGHLIGHTS FEATURES • Various solutions to protect single lines against surges • Lightning Arrestors (CDL4U(E)LA) • MOVs (CDL4U(E)MOV) • RC Circuits (CDL4U(E)RC) • Suppressor Diode (CDL4U(E)SD) CDL4U(E)LA CB SCHEME Lightning Arrestor to protect data and signal lines 3 pole lightning arrestor to protect line / line and line / earth surges RC circuit to protect DC solenoid valves and contactors Dimensions & Weight APPLICATIONS • Surge suppressor Width 18 mm 18 mm 18 mm Length 55.5 mm 55.5 mm 55.5 mm • Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 55.7 mm 63.1 mm 30.0 g 34.2 g 22.4 g applications Equipment protection Weight per piece Technical Data/Ratings / Component Specifications Wire Size (solid / stranded) Insulation Material 22-10 AWG 22-10 AWG 22-10 AWG Polyamide 66 Polyamide 66 Polyamide 66 10 A 5A - - - 2kA-6.5kA (8/20ms) 20 KA (8/20ms) 10 KA (8/20ms) - 100 ns 100 ns < 25 ns Nominal Current Peak Current Nominal Discharge Current Response Time Capacitance Voltage Rating < 1.5 pf < 1.0 pf 100 - 20,000 pf 75, 90, 230, 600, 1000 V DC 90, 230, 350, 600 V DC 30, 60, 75, 130, 275, 460, 510, 625, 680 V AC 9 mm 9 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Grey Std. Pk. CDL4U(E)LA/75V CDL4U(E)LA/90V CDL4U(E)LA/230V CDL4U(E)LA/600V CDL4U(E)LA/1000V 20 20 20 20 20 Cat. No. Std. Pk. CDL4U(E)3LA/90V CDL4U(E)3LA/230V CDL4U(E)3LA/350V CDL4U(E)3LA/600V 20 20 20 20 Cat. No. Std. Pk. 0.1 mF CDL4U(E)RC0.1 10 0.22 mF CDL4U(E)RC0.22 10 Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. End Plate EPCDL4U 50 EPCDL4U 50 EPCDL4U 50 Spacer CDL4USP 50 CDL4USP 50 CDL4USP 50 DIN Rail 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 Marking Tag MT2 Accessories 46 Cat. No. 1 Pk. (100 tags) MT2 1 Pk. (100 tags) MT2 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 Std. Pk. 1 Pk. (100 tags) ELECTRONIC COMPONENTS SURGE SUPPRESSOR TERMINAL BLOCKS CDL4U(E)MOV SCREW TERMINAL BLOCKS CTLG2.5(E)MOV CDL4U(E)SD SDUA CDL4U(E)MOV SDUK CTLG2.5(E)MOV SDB MOV for voltage surge spike protection MOV for voltage surge spike protection Suppressor Diode to fine protect sensors, contacts, etc Width 12 mm 6 mm 12 mm Length 55.5 mm 87.5 mm 55.5 mm Height w DIN Rail 35 x 7.5 mm 35 x 15 mm 55.7 mm 63.1 mm 66.0 mm 74.0 mm 55.7 mm 63.1 mm 19.2 g 14.8 g 18.0 g CB SCHEME Dimensions & Weight Weight per piece Technical Data/Ratings / Component Specifications Wire Size (solid / stranded) 22-10 AWG 22-10 AWG 22-10 AWG Polyamide 66 Polyamide 66 Polyamide 66 - 5A - 2kA-6.5kA (8/20ms) 2kA-6.5kA (8/20ms) - - 10 KA (8/20ms) 1.5 KA 1 ns (D.C) / 5 ns (A.C) Insulation Material Nominal Current Peak Current Nominal Discharge Current Response Time < 25 ns < 25 ns 100 - 20,000 pf 100 - 20,000 pf - 30, 60, 75, 130, 275, 460, 510, 625, 680 V AC Up to 275V 30, 60, 75, 130, 275, 460, 510, 625, 680 V AC Capacitance Voltage Rating Installation Instructions Wire Stripping Length Screwdriver Terminal Blocks Grey 9 mm 9 mm 9 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Flat Head 0.6 x 3.5 mm Cat. No. Std. Pk. CDL4U(E)MOV30V CDL4U(E)MOV60V CDL4U(E)MOV75V CDL4U(E)MOV130V CDL4U(E)MOV275V CDL4U(E)MOV460V CDL4U(E)MOV510V CDL4U(E)MOV625V CDL4U(E)MOV680V 20 20 20 20 20 20 20 20 20 Cat. No. Std. Pk. CTLG2.5(E)MOV30V CTLG2.5(E)MOV60V CTLG2.5(E)MOV75V CTLG2.5(E)MOV130V CTLG2.5(E)MOV275V 20 20 20 20 20 Cat. No. Std. Pk. DC - Anode CDL4U(E)SDUA12VDC 20 CDL4U(E)SDUA24VDC 20 CDL4U(E)SDUA48VDC 20 DC - Cathode CDL4U(E)SDUK12VDC 20 CDL4U(E)SDUK24VDC 20 CDL4U(E)SDUK48VDC 20 AC CDL4U(E)SDB12VAC CDL4U(E)SDB24VAC CDL4U(E)SDB48VAC CDL4U(E)SDB160VAC Std. Pk. Cat. No. Std. Pk. EPCTLG2.5 50 EPCDL4U 50 50 – – CDL4USP 50 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 2511120 CA701-15/S 2511160 20 20 10 End Stop CA702 CA802 50 50 CA702 CA802 50 50 CA702 CA802 50 50 Marking Tag MT2 Accessories Cat. No. Std. Pk. End Plate EPCDL4U 50 Spacer CDL4USP DIN Rail 1 Pk. (100 tags) Cat. No. MT2 1 Pk. (100 tags) MT2 1 Pk. (100 tags) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 47 ACCESSORIES JUMPER / SHORTING LINKS SCREW TERMINAL BLOCKS Internal Jumper CTS2.5U-N CTS4U-N, CCC4U, CMC1-2, CMC2-2, CDL4UN, CDL4U(I.S) CDLG4, CDLG(I.S), CF4SP, CF4SP(L), CKT4U1, CKT4SP CTS6U, CDS6U CDTTU1, CDTTU-SH1 CTS10U CTS16U CTS25UN CTS35UN CTS50/70N CTS95/120N CTL2.5U, CTL2.5U(L) CTL2.5U-H, CTL2.5U-H(L) CTL2.5U(I.S) ODL4U CDL4U(E) CMT4 CMB4 CDLG2.5 CTLG2.5 CF4U1 CF4U(L)1 DDFL4U, DDFL4U(E) DDFL4ULR, DDFL4ULR(E) CSDL4U1, DDDL4U CAFL4U1 CAFL4U(L)1 CAFL4U(N)1 CHV4U CTS4USC CHV6U CTS6USC CHV10U CTS10USC 48 Poles 2 Pole 3 Pole 4 Pole 10 Pole 100 Pole 2 Pole 3 Pole 4 Pole 10 Pole 100 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 2 Pole 3 Pole 2 Pole 3 Pole 4 Pole 10 Pole 100 Pole2 2 Pole 3 Pole 4 Pole 10 Pole 100 Pole2 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole 2 Pole 3 Pole 4 Pole 10 Pole Cat. No. CA721/2 CA721/3 CA721/4 CA721/10 CA721/100 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 CA723/2 CA723/3 CA723/4 CA723/10 CA724/2 CA724/3 CA724/4 CA724/10 CA751/2 CA751/3 CA751/4 CA751/10 CA725/2 CA725/3 CA725/4 CA725/10 CA771/2 CA771/3 CA771/4 CA771/10 CA628/2 CA628/3 CA629/2 CA629/3 CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 CA727/2 CA727/3 CA727/4 CA727/10 CA727/100 CA627/2 CA627/3 CA627/4 CA627/10 CA729/2 CA729/3 CA729/4 CA729/10 CA623/2 CA623/3 CA623/4 CA623/10 CA624/2 CA624/3 CA624/4 CA624/10 CA625/2 CA625/3 CA625/4 CA625/10 Std. Pk. 100 100 100 10 10 100 100 100 10 10 100 50 50 10 100 50 50 10 50 50 50 10 50 20 20 10 50 20 20 10 10 10 10 10 100 100 100 10 10 100 100 100 10 10 100 100 100 10 100 50 50 10 100 100 100 10 100 100 100 10 100 100 100 10 Insulated Internal Jumper Cat. No. CA741/2 CA741/3 CA741/4 CA741/10 CA741/100 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 CA743/2 CA743/3 CA743/4 CA743/10 CA744/2 CA744/3 CA744/4 CA744/10 CA761/2 CA761/3 CA761/4 CA761/10 CA745/2 CA745/3 CA745/4 CA745/10 CA781/2 CA781/3 CA781/4 CA781/10 CA747/2 CA747/3 CA747/4 CA747/10 CA747/100 CA749/2 CA749/3 CA749/4 CA749/10 - Std. Pk. 100 100 100 10 10 100 100 100 10 10 100 50 50 10 100 50 50 10 50 50 50 10 50 20 20 10 50 20 20 10 100 100 100 10 10 100 50 50 10 - External Jumper Current Bar Shorting Sleeve & Screws Cat. No. CA717/2 CA717/3 CA717/4 CA717/10 CA714/2 CA714/3 CA714/4 CA714/10 CA710/2 CA710/3 CA710/4 CA710/10 CA718/2 CA718/3 CA718/4 CA718/10 CA715/2 CA715/3 CA715/4 CA715/10 CA714/2 CA714/3 CA714/4 CA714/10 CA715/2 CA715/3 CA715/4 CA715/10 CA711/2 CA711/3 CA711/4 CA711/10 CA711/2 CA711/3 CA711/4 CA711/10 CA716/2 CA716/3 CA716/4 CA716/10 - Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. 100 CA703/01 100 100 CA704/01 100 100 CA705/01 100 CA707/S/Q/01 100 20 CA731/10 100 CA731/100 10 100 CA703/1 100 100 CA704/1 100 100 CA705/1 100 CA707/S/Q/01 100 20 CA732/10 100 CA732/100 10 100 CA703/2 100 50 CA704/2 100 CA707/S/Q/1 100 50 CA705/2 100 20 CA733/10 10 100 CA703/3 100 50 CA704/3 100 100 CA707/S/Q/1 50 CA705/3 100 20 CA734/10 10 CA703/8 100 CA704/8 100 CA707/S/Q/1 100 CA705/8 100 CA739/10 10 CA703/4 100 CA704/4 100 CA707/S/Q/2 100 CA705/4 100 CA735/10 100 CA703/10 100 CA704/10 100 CA707/S/Q/2 100 CA705/10 100 CA770/10 10 100 CA703/1 100 100 CA704/1 100 100 CA705/1 100 CA707/S/Q/01 100 20 CA732/10 100 CA732/100 10 100 CA703/1 100 100 CA704/1 100 100 CA705/1 100 CA607/S/Q 100 20 CA732/10 100 CA732/100 10 100 CA703/1 100 100 CA704/1 100 CA611/S/Q 100 100 CA705/1 100 20 CA732/10 10 100 50 50 20 100 CA703/6 100 50 CA704/6 100 CA707/S/Q/3 100 50 CA705/6 100 20 CA737/10 100 50 50 50 20 1 Internal shorting system not available. 2 - is breakable - poles needed. 100 pole strip into any -number of - Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 ACCESSORIES VARIOUS ACCESSORIES SCREW TERMINAL BLOCKS ENDPLATES Terminal Block PARTITION PLATES Cat. No. CTS2.5U-N, CTS4U-N CTT2.5UK/J/T/E CCTS6U, CTS10U CMC1-2 CMC2-2, CMCG4 CDL4UN, CDLG4 CDLG2.5 CTLG2.5 ODL4U CHV Series, CTSUSC Series CTL2.5U Series CTL2.5U-H Series CAFL4U Series CDS6U CKT4U EPCKT4U CDTTU Series CSDL4U DDDL4U, DDFL4U CDL4U(E) CTC4U CMT4 CMB4 ODL2.5 Series Dimensions EP2.5/4UN EP6/10U EPCMC1-2 EPCMC2-2 EPCDL4UN EPCDLG2.5 EPCTLG2.5 EPODL4U (Front) EP1ODL4U (Back) EPUSC EPCTL2.5U EPCTL2.5U-H EPCAFL4U EPCDS6U EPCKT4U EPCKT4U/4 EPCDTTU EPCSFL4U EPDDFL4U EPCDL4U EPCTC4U EPCMT4 EPCMB4 EPODL2.5 EP1ODL2.5 Std. Pk. 32 x 39 x 1.5mm 50 31 x 42.5 x 1.5mm 35.5 x 46.5 x 2.5mm 40.5 x 65 x 2.5mm 47.5 x 57 x 1.5mm 48 x 71.4 x 1.2mm 62.5 x 87.5 x 1.2mm 49 x 86 x 5.5mm 24 x 68 x 3mm 52 x 48.5 x 1.5mm 55.5 x 84 x 1.5mm 55.5 x 61 x 1.5mm 32 x 72 x 1.5mm 37.2 x 82 x 1.5mm 30.5 x 46.5 x 2.5mm 65 x 38.3 x 1.5mm 41 x 63 x 3mm 28 x 55.5 x 1.6mm 49 x 87.6 x 3mm 43 x 55 x 2.4mm 34.5 x 47 x 2.5mm 23 x 27 x 1.5mm 27 x 27 x 7mm 49 x 59 x 4.6mm 23 x 59 x 2.5mm 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 Terminal Block CTS2.5U-N, CTS4U-N CTT2.5UK/J/T/E CTS6U, CTS10U CTS25UN CTS35UN CMT4 Cat. No. PP2.5/4UN Dimensions Std. Pk. 37 x 44 x 1.6mm 50 37.5 x 56 x 1.5mm 42.5 x 62 x 1mm 50 x 64.5 x 1mm 32 x 37 x 1.6mm 50 50 50 50 Dimensions Std. Pk. SP2.5/4UN 17.5 x 17.4 x 1.4mm 100 SP6/10U SPCDL4U SPCMB4 SPCDLG2.5 15.4 x 16.2 x 1.5mm 15.4 x 16.2 x 1.6mm 14.5 x 12 x 1.5mm 11 x 10.5 x 1 100 100 100 100 PP6/10U PP25UN PP35UN PPCMT4 SEPARATOR PLATES Terminal Block CTS2.5U-N, CTS4U-N CTT2.5UK/J/T/E CTS6U, CTS10U, CTS16U CSL4UN, CDL4UN(I.S.) CBM4 CDLG2.5 Cat. No. END STOPS CA202 Cat. No. CA202 CA802 Dimensions Std. Pk. 44.5 x 50 x 9.5mm 50 Cat. No. CA802 Dimensions 45 x 32 x 8mm CA702 Std. Pk. 50 Cat. No. CA702 Dimensions 34 x 45 x 9mm CA102 Std. Pk. 50 Cat. No. CA102 Dimensions 80 x 46 x 9mm Std. Pk. 50 PROTECTIVE COVER CTSPC COVER SUPPORT PLATE Length Cat. No. CTSPC/40 CTSPC/90 CTSPC/100 CTSPC/130 CTSPC/150 CTSPC/200 CTSPC/300 CTSPC/330 Length 40mm 90mm 100mm 130mm 150mm 200mm 300mm 330mm Std. Pk. 2 2 2 2 2 2 2 2 Cat. No. CSP1 Std. Pk. 50 Assembled Block installed with Protective Cover Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 49