Altech Corporation
35 Royal Road
Flemington, NJ 08822-6000
P 908.806.9400 • F 908.806.9490
www.altechcorp.com
Altech Corp.® 410-112013-5M
Printed November 2013
Since 1984, Altech Corporation has grown to become a leading supplier of automation and industrial
control components. Headquartered in Flemington, NJ, Altech has an experienced staff of
engineering, manufacturing and sales personnel to provide the highest quality products with superior
service. This is the Altech Commitment!
IE5 Series
With experienced Product Engineers and Customer Service personnel, Altech provides solutions to
your most pressing application challenges. All with one thought in mind - to ensure that we solve
your problem the first time!
Quality
Commitment
Altech’s control components meet diverse national
and international standards such as UL, NEC, CSA,
IEC, VDE and more. Altech provides superior
customer service and delivery through Total Quality
Management and Continuous Process Improvement.
Altech is ISO 9001 approved. We perform these
services with honesty and integrity and are committed
to achieve these goals.
#
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
TABLE OF CONTENTS
INTERFACE MODULES INTRODUCTION ...................................................4-5
Connector to Terminal Block Modules.....................................................6-9
Diode Modules & Component Carriers ................................................10-14
Wire to RJ45 Module ...................................................................................15
Interface Relay Modules and Carriers..................................................16-23
Interfaces, High Current Isolated..........................................................24-27
Safety Relay Modules.............................................................................28-41
Interfaces.................................................................................................42-45
PCB Mounting Tracks...............................................................................46-47
INDUSTRIAL RELAYS INTRODUCTION ..................................................48-49
Industrial Electromagnetic Relays ........................................................50-71
Miniature Electromagnetic Relays ........................................................72-83
Slimline Interface Relays .......................................................................84-89
Subminiature Electromagnetic and Solid State Relays ....................90-101
Relays for Photovoltaic Systems ......................................................102-103
Relay Socket Combination ................................................................104-109
Industrial Relay Accessories .............................................................110-115
Index.......................................................................................................118-121
Terms & Conditions......................................................................................122
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
3
INTERFACE MODULES
TEXT
Text
Link incompatible hardware or
expand the capabilities of logic
systems with Altech interface and
electronic modules and carriers.
These DIN Rail or panel mounted
printed circuit board modules,
subsystems and carriers give
design flexibility, simplify panel
layouts and reduce maintenance
and downtime.
Altech’s compact interface
modules provide a flexible, cost
effective transition from Sub-D,
Ribbon Cable and other
connectors to terminal blocks.
Altech’s electronic modules
include Diode, Fuse, Varistor,
Optocoupler (I/O), Relay, power
supplies and custom modules.
If your needs go beyond our
comprehensive range of standard
interface and electronic modules,
Altech can custom design a
module to meet even the most
sophisticated requirements.
Modules are supplied completely
assembled with ready to wire
screw-cage terminal blocks in an
extruded track. The track can be
mounted on 35 or 32mm DIN Rail
or can be panel mounted. Select
individual components and mount
your own electronic boards with
Altech mounting tracks.
4
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interface Modules
CONNECTOR-TO-TERMINAL BLOCK
DIODE MODULES & COMPONENT CARRIERS
Compact and reliable transitions
between high density connectors
and high quality screw-cage
clamp terminal blocks.
Use our Diode Modules to build lamp
test circuits, decouple signals, etc.
Mount your own components into our
Component Carriers (supplied without
electronic components). Or, tell us what
you need and we’ll install it for you.
• FBK Ribbon Cable, up to 64 poles
• Subminiature - D, up to 50 poles
• DM Diode Modules have series
connection 1A or 3A diodes, and 1A diode gates with common
cathodes or anodes, providing commonly used diode
arrangements
MINIATURE RELAYS
• BSM Component Carrier has factory installed fork-and eyelet
soldering posts in each series trace
Traditional relay and safety relay
modules in a high density package.
•
•
•
•
Protect equipment
Provide insulation
Control motors, solenoid and valves
Safety relays for emergency stop, safety gate
and two-hand stop
• CCA Component Carrier consists of a printed circuit board with
four in-line and two bus-connection through-holes to solder pads
in each trace, complete with terminal blocks
CUSTOM INTERFACE MODULES
If your design or application requires more functionality or features than our standard product, Altech offers complete engineering,
prototype and production services for custom modules.
Our staff has the ability to take your design or requirements and manufacture your custom module. Custom module production
generally includes engineering, PCB layout and prototypes, packaged in Altech extrusions for mounting on panels or DIN Rail. In many
industrial control systems, customized designs are the solution for many problems.
Altech provides a quick turnaround and competitive solution to your problem.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
5
CONNECTOR TO TERMINAL BLOCK MODULES
INTERFACES CONNECTOR-TO-WIRE
Ribbon Cable Module
35 or 32 mm DIN Rail
Compact Ribbon Connector Modules provide an interface between multi-wire
flat cables outfitted with IDC connectors and discrete wires. Up to 64
conductors can be terminated saving time and eliminating wiring mistakes.No
special wiring or tools are required. Ribbon Cable Interface Modules are
typically used in communications, data processing, process control and other
industrial applications. FBK Ribbon Cable Modules are supplied with short
strain relief ejector latches (long ejector latches are available), screw-cage
clamp terminal blocks and component solder pads for easy insertion of circuit
building components. All terminal blocks are individually marked to correspond
to the numbers on the header pins.
•
•
•
•
•
•
Screw-Cage Clamp Connections
Spring Clamp Connections Available
Up to 64 Poles
4 to 5 Component Solder Pads Per Line
.9mm (.035 in.) Diameter Component Mounting Holes
DIN Rail Mount and Panel Mount Available
INTERFACES CONNECTOR-TO-WIRE
Subminiature D Module
35 or 32 mm DIN Rail
Compact Subminiature D (Sub D) Modules provide quick and reliable interfaces
between high density connectors (back shells) with up to 50 poles and discrete
wires. Connector-to-Wire Interface modules save time and eliminate wiring
mistakes. No special tools are required. Sub D Interface modules are typically
used in communications, data processing, process control and other industrial
applications. Keyed by design, Sub D Modules are equipped with male or
female connectors, screw-cage clamp terminal blocks, and component solder
pads for easy insertion of circuit building components. All terminal blocks are
individually marked to correspond to the numbers on the connector pins or
sockets.
•
•
•
•
•
•
6
Screw-Cage Clamp Connections
Spring Clamp Connections Available
4 to 5 Component Solder Pads Per Line
.9mm (.035 in.) Diameter Component Mounting Holes
DIN Rail Mount, Panel Mount Available
SD-F50 and SD-M50 are double-sided boards and
do not have component solder pads.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interface Modules
Connector to terminal block modules
INTERFACES CONNECTOR-TO-WIRE
Ribbon Cable Module FBK
35 or 32mm DIN Rail Mount
For Signal Processing
TS35x7.5 70mm (2.75 in.)
TS32x15 75mm (2.95 in.)
L
Technical Information
87
m
m
3
.4
(3
.)
in
Current ..................3 A max
Voltage ..................250V AC
Wire Range ...........0.5-4 mm2 / 22-12 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
SCREW CLAMP
Part Number
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
5720.2
5721.2
5722.2
5723.2
5724.2
5725.2
5726.2
5727.2
5728.2
5729.2
FBK10
FBK14
FBK16
FBK20
FBK26
FBK34
FBK40
FBK50
FBK60
FBK64
10
14
16
20
26
34
40
50
60
64
46 (1.81)
46 (1.81)
68 (2.68)
68 (2.68)
80 (3.15)
93 (3.66)
114 (4.49)
139 (5.47)
180 (7.09)
180 (7.09)
1
1
1
1
1
1
1
1
1
1
Part Number
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
5720.2/S
5721.2/S
5722.2/S
5723.2/S
5724.2/S
5725.2/S
5726.2/S
5727.2/S
5728.2/S
5729.2/S
FBK10
FBK14
FBK16
FBK20
FBK26
FBK34
FBK40
FBK50
FBK60
FBK64
10
14
16
20
26
34
40
50
60
64
46 (1.81)
46 (1.81)
68 (2.68)
68 (2.68)
80 (3.15)
93 (3.66)
114 (4.49)
139 (5.47)
180 (7.09)
180 (7.09)
1
1
1
1
1
1
1
1
1
1
SPRING CLAMP
Female Connector SD-F37
37 Pin Socket Female Connector
Shown with component counting holes
PTH holes for convenient component
insertion and easy soldering.
Other models available; please contact Altech.
Suffix ...................Description
none ....................Screw Terminal; DIN Rail Mount
/S ......................Spring Terminal; DIN Rail Mount
/P ......................Screw Terminal; Panel Mount
Suffix ...................Description
/L ......................Screw Terminal; Long Latch Connector; DIN Rail Mount
/SL .....................Spring Terminal; Long Latch Connector; DIN Rail Mount
/SP .....................Spring Terminal; Panel Mount
Example: Part Number 5727.2/L for Long Latch model.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
7
Interface Modules
Connector to terminal block modules
INTERFACES CONNECTOR-TO-WIRE
Subminiature SD Male Module
35 or 32 mm DIN Rail Mount
For Signal Processing
TS35x7.5 70mm (2.75 in.)
TS32x15 75mm (2.95 in.)
L
Technical Information
87
m
m
.
(3
43
.)
in
Current ..................3 A max
Voltage ..................250V AC
Wire Range ...........0.5-4 mm2 / 22-12 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
SCREW CLAMP
Part Number
5740.2
5741.2
5741.3*
5742.2
5743.2
a,b
5744.2
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
SD-M9
SD-M15
HDSD-M15
SD-M25
SD-M37
SD-M50
9
15
15
25
37
50
45 (1.77)
53 (2.09)
53 (2.09)
80 (3.15)
113 (4.45)
136 (5.35)
1
1
1
1
1
1
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
SD-M9
SD-M15
HDSD-M15
SD-M25
SD-M37
SD-M50
9
15
15
25
37
50
45 (1.77)
53 (2.09)
53 (2.09)
80 (3.15)
113 (4.45)
136 (5.35)
1
1
1
1
1
1
SPRING CLAMP
Part Number
5740.2/S
5741.2/S
5741.3/S*
5742.2/S
5743.2/S
a,b
5744.2/S
PTH holes for convenient component
insertion and easy soldering.
Female Connector SD-F37
37 Pin Socket Female Connector
Shown with component counting holes
(pads are on solder side)
Female Connector SD-F50
50 Pin Socket Female Connector
Shown with no component solder pads
Other models available; please contact Altech.
Suffix ...................Description
none ....................Screw Terminal; DIN Rail Mount
/S ......................Spring Terminal; DIN Rail Mount
/P ......................Screw Terminal; Panel Mount
Suffix ...................Description
/L ......................Screw Terminal; Long Latch Connector; DIN Rail Mount
/SL .....................Spring Terminal; Long Latch Connector; DIN Rail Mount
/SP .....................Spring Terminal; Panel Mount
Example: Part Number 5727.2/L for Long Latch model.
*a High density version.
b
SD-M50 is only available with a 1.5A current rating.
8
SD-F50 and SD-M50 are double-sided boards and do not have component solder pads.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interface Modules
Connector to terminal block modules
TS35x7.5 70mm (2.75 in.)
TS32x15 75mm (2.95 in.)
INTERFACES CONNECTOR-TO-WIRE
Subminiature SD Female Module
35 or 32 mm DIN Rail Mount
For Signal Processing
L
Technical Information
Current ..................3 A max
Voltage ..................250V AC
Wire Range ...........0.5-4 mm2 / 22-12 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
87
m
m
(3
3
.4
.)
in
SCREW CLAMP
Part Number
5745.2
5746.2
5746.3*
5747.2
5748.2
a,b
5749.2
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
SD-F9
SD-F15
HDSD-F15
SD-F25
SD-F37
SD-F50
9
15
15
25
37
50
45 (1.77)
49 (1.93)
49 (1.93)
80 (3.15)
113 (4.45)
136 (5.35)
1
1
1
1
1
1
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
SD-F9
SD-F15
HDSD-F15
SD-F25
SD-F37
SD-F50
9
15
15
25
37
50
45 (1.77)
49 (1.93)
49 (1.93)
80 (3.15)
113 (4.45)
136 (5.35)
1
1
1
1
1
1
SPRING CLAMP
Part Number
5745.2/S
5746.2/S
5746.3/S*
5747.2/S
5748.2/S
a,b
5749.2/S
PTH holes for convenient component
insertion and easy soldering.
Female Connector SD-F37
37 Pin Socket Female Connector
Shown with component counting holes
(pads are on solder side)
Female Connector SD-F50
50 Pin Socket Female Connector
Shown with no component solder pads
Other models available; please contact Altech.
Suffix ...................Description
none ....................Screw Terminal; DIN Rail Mount
/S ......................Spring Terminal; DIN Rail Mount
/P ......................Screw Terminal; Panel Mount
Suffix ...................Description
/L ......................Screw Terminal; Long Latch Connector; DIN Rail Mount
/SL .....................Spring Terminal; Long Latch Connector; DIN Rail Mount
/SP .....................Spring Terminal; Panel Mount
Example: Part Number 5727.2/L for Long Latch model.
*a High density version.
b
SD-M50 is only available with a 1.5A current rating.
SD-F50 and SD-M50 are double-sided boards and do not have component solder pads.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
9
DIODE MODULES & COMPONENT CARRIERS
INTERFACES
DM Diode Module
35 or 32mm DIN Rail Mount
Wire individually labeled diodes into existing circuits for freewheeling, DC
inductive kick suppression (commutating), reverse DC polarity protection, etc.
Use bussed diodes for distribution of logic Vcc or ground, or gather and
decouple electrical signals for lamp testing or collective fault messages. Use
as commutating diodes across inductive loads such as DC relays, solenoid
valves, actuator magnets, etc. to suppress voltage surges.
Standard modules include series connection diode circuits in 1 Amp and 3
Amp versions, and diode gates with bussed anodes or cathodes.
• Screw-Cage Clamp Connections
• Special Configurations Available
• DIN Rail Mount, Panel Mount Available
INTERFACES
Component Carriers
35 or 32mm DIN Rail
Use Component Carriers to modify and/or build circuits to meet special
requirements. Type CCA requires removal of the single solder-side printed
circuit board from the mounting track for soldering of components. Posts
or through-leads can be installed for future field connections. Contact Altech
for custom installation of solder posts. Type BSM allows field additions of
diodes for decoupling, line crossovers for testing or multiplying tie-in
terminals for a line. Pre-installed flat, fork-and-eyelet soldering posts allow
component-side mechanical and solder connections with minimum
disruption to wiring and mounted devices.
• Screw-Cage Clamp Connections
• Terminal Blocks are Numbered for Easy Wire Identification
• DIN Rail Mount, Panel Mount Available
INTERFACES
Dip Socket Carrier - 3 Amp
35 or 32mm DIN Rail Mount
Enhance design capabilities with Dual In-Line Package (DIP) Socket Carriers,
the most versatile socket available. Use our DIPCs for reed-relays, power
relays, photo-isolated Input/Output modules, in-line switches, thin film
resistors and more. The Altech DIPC is rated 3 Amp and is available in 14, 16
and 20 pin socket configurations. Each DIPC module has several component
solder pads for loading circuit-building components.
•
•
•
•
10
Screw-Cage Clamp Connections
4 to 5 Component Solder Pads Per Line
.9mm (.035 in.) Diameter Component Mounting Holes
DIN Rail Mount, Panel Mount Available
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interface Modules
Diode modules & component carriers
INTERFACES
DM Diode Module
35 or 32 mm DIN Rail Mount
TS35x7.5 56mm (2.21 in.)
TS32x15 61mm (2.40 in.)
L
Technical Information
87
Diode
Rated Current
1N4007 or equivalent
1A
1N5408 or equivalent
3A
P600M or equivalent
6A
Maximum Blocking Voltage - 1000V DC
Rated Bus Current: 10A
(12A at 30˚C (86˚F) Temperature Rise)
Wire Range ...........0.5-4 mm2; 22-12 AWG
Voltage ..................250V AC
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
m
m
.
(3
43
.
in
)
SCREW CLAMP *
1 AMP
Part Number
8971.2
5702.2
5703.2
8973.2
8974.2
8975.2
8842.2
5704.2
5705.2
8850.2
5706.2
5707.2
3 AMP
Part Number
8971.3
5702.3
5703.3
8973.3
8974.3
8975.3
8842.3
5704.3
5705.3
8850.3
5706.3
5707.3
6 AMP
Part Number
8971.4
5702.4
5703.4
8973.4
8974.4
8975.4
8842.4
5704.4
5705.4
8850.4
5706.4
5707.4
Type
Ordering Information
No. of Diodes
Diode
DM4-S
DM8-S
DM12-S
DM16-S
DM20-S
DM24-S
DM6-A-S
DM14-A-S
DM22-A-S
DM6-K-S
DM14-K-S
DM22-K-S
Series Connection, 1A diodes
Series Connection, 1A diodes
Series Connection, 1A diodes
Series Connection, 1A diodes
Series Connection, 1A diodes
Series Connection, 1A diodes
Bussed Anodes, 1A diodes
Bussed Anodes, 1A diodes
Bussed Anodes, 1A diodes
Bussed Cathodes, 1A diodes
Bussed Cathodes, 1A diodes
Bussed Cathodes, 1A diodes
4
8
12
16
20
24
6
14
22
6
14
22
1N4007
1N4007
1N4007
1N4007
1N4007
1N4007
1N4007
1N4007
1N4007
1N4007
1N4007
1N4007
Type
Ordering Information
No. of Diodes
Diode
DM4-S3
DM8-S3
DM12-S3
DM16-S3
DM20-S3
DM24-S3
DM6-A-S3
DM14-A-S3
DM22-A-S3
DM6-K-S3
DM14-K-S3
DM22-K-S3
Series Connection, 3A diodes
Series Connection, 3A diodes
Series Connection, 3A diodes
Series Connection, 3A diodes
Series Connection, 3A diodes
Series Connection, 3A diodes
Bussed Anodes, 3A diodes
Bussed Anodes, 3A diodes
Bussed Anodes, 3A diodes
Bussed Cathodes, 3A diodes
Bussed Cathodes, 3A diodes
Bussed Cathodes, 3A diodes
4
8
12
16
20
24
6
14
22
6
14
22
1N5408
1N5408
1N5408
1N5408
1N5408
1N5408
1N5408
1N5408
1N5408
1N5408
1N5408
1N5408
Type
Ordering Information
No. of Diodes
Diode
DM4-S6
DM8-S6
DM12-S6
DM16-S6
DM20-S6
DM24-S6
DM6-A-S6
DM14-A-S6
DM22-A-S6
DM6-K-S6
DM14-K-S6
DM22-K-S6
Series Connection, 6A diodes
Series Connection, 6A diodes
Series Connection, 6A diodes
Series Connection, 6A diodes
Series Connection, 6A diodes
Series Connection, 6A diodes
Bussed Anodes, 6A diodes
Bussed Anodes, 6A diodes
Bussed Anodes, 6A diodes
Bussed Cathodes, 6A diodes
Bussed Cathodes, 6A diodes
Bussed Cathodes, 6A diodes
4
8
12
16
20
24
6
14
22
6
14
22
P600M
P600M
P600M
P600M
P600M
P600M
P600M
P600M
P600M
P600M
P600M
P600M
Module Length (L)
in mm(in.)
24 (0.95)
44 (1.73)
64 (2.52)
92 (3.62)
112 (4.41)
132 (5.20)
30 (1.18)
50 (1.97)
70 (2.75)
30 (1.18)
50 (1.97)
70 (2.75)
Std. Pk.
Figure
1
1
1
1
1
1
1
1
1
1
1
1
A
A
A
A
A
A
B
B
B
C
C
C
Module Length (L)
in mm(in.)
24 (0.95)
44 (1.73)
64 (2.52)
92 (3.62)
112 (4.41)
132 (5.20)
30 (1.18)
50 (1.97)
70 (2.75)
30 (1.18)
50 (1.97)
70 (2.75)
Std. Pk.
Figure
1
1
1
1
1
1
1
1
1
1
1
1
A
A
A
A
A
A
B
B
B
C
C
C
Module Length (L)
in mm(in.)
24 (0.95)
44 (1.73)
64 (2.52)
92 (3.62)
112 (4.41)
132 (5.20)
30 (1.18)
50 (1.97)
70 (2.75)
30 (1.18)
50 (1.97)
70 (2.75)
Std. Pk.
Figure
1
1
1
1
1
1
1
1
1
1
1
1
A
A
A
A
A
A
B
B
B
C
C
C
Figure A
Figure B
Figure C
* Spring Terminal is available; add suffix S to end of part number. Example: Part Number 8971.2/S for Spring Terminal.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
11
Interface Modules
Diode modules & component carriers
INTERFACES
CCA Component Carrier
35 or 32 mm DIN Rail Mount
with PTH holes
TS35x7.5 56mm (2.20 in.)
TS32x15 61mm (2.40 in.)
L
Technical Information
87
Current ..................6 A (12 A Bus)
Terminal.................15 A
Voltage ..................250V AC
Wire Range ...........0.5-4 mm2 / 22-12 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
m
m
3
.4
(3
.)
in
SCREW CLAMP
Part Number
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
8835.2
8836.2
8837.2
8838.2
8839.2
8840.2
CCA4
CCA8
CCA12
CCA16
CCA20
CCA24
4
8
12
16
20
24
24 (.87)
44 (1.65)
64 (2.44)
84 (3.23)
104 (4.02)
124 (4.80)
1
1
1
1
1
1
Part Number
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
8835.2/S
8836.2/S
8837.2/S
8838.2/S
8839.2/S
8840.2/S
CCA4
CCA8
CCA12
CCA16
CCA20
CCA24
4
8
12
16
20
24
24 (.87)
44 (1.65)
64 (2.44)
84 (3.23)
104 (4.02)
124 (4.80)
1
1
1
1
1
1
SPRING CLAMP
PTH holes for convenient component
insertion and easy soldering.
CCA Type
12
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interface Modules
Diode modules & component carriers
INTERFACES
BSM Component Carrier
35 or 32 mm DIN Rail Mount
with solder posts
TS35x7.5 56mm (2.20 in.)
TS32x15 61mm (2.40 in.)
L
Technical Information
87
Current ..................6 A (12 A Bus)
Terminal.................15 A
Voltage ..................250V AC
Wire Range ...........0.5-4 mm2 / 22-14 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
m
m
3
.4
(3
.)
in
SCREW CLAMP
Part Number
5700.2
5701.2
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
BSM8-S
BSM12-S
16
24
47 (1.85)
69 (2.72)
1
1
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
BSM8-S
BSM12-S
16
24
47 (1.85)
69 (2.72)
1
1
SPRING CLAMP
Part Number
5700.2/S
5701.2/S
2.81mm
(.11 in.)
3.0mm
(.118 in.)
1.32mm
(.05 in.)
.90mm (.035 in.)
Solder Post
BSM Type
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
13
Interface Modules
Diode modules & component carriers
TS35x7.5 70 mm (2.75 in.)
TS32x15 75 mm (2.95 in.)
INTERFACES
Dip Socket Carrier - 3 Amp
35 or 32mm DIN Rail Mount
L
87
Typical Applications:
14 Pin
Magnecraft® Classes 107, 171, 172;
S-D® Series MRR-D; Hamlin® 700;
Dale® TDP14 Resistors; etc.
16 Pin
Most P&B® including T85 Hi Sens and
I/O Modules IA, OA, OD16;
Midtex® 190 Power;
Augat® Alcoswitch® GD, AD Series, etc.
20 Pin
C&K® BD series switches;
Grayhill® 79 coded switches;
AMP® 7600 shunts; etc.
m
m
3
.4
(3
.)
in
Technical Information
a
Current ..................3 A
Voltage ..................250V AC
Wire Range ...........0.5-4 mm2 / 22-12 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
SCREW CLAMP
Part Number
8937.2
8938.2
8939.2
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
DIPC14
DIPC16
DIPC20
14
16
20
45 (1.77)
68 (2.68)
68 (2.68)
1
1
1
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
DIPC14
DIPC16
DIPC20
14
16
20
45 (1.77)
56 (2.20)
56 (2.20)
1
1
1
PTH holes for convenient
component insertion and
easy soldering.
a
7.62 mm (.300 in.)
8937.2/S
8938.2/S
8939.2/S
7.62 mm (.300 in.)
Part Number
7.62 mm (.300 in.)
SPRING CLAMP
Current Ratings
Printed Circuit Traces: 3.5A
Terminal Blocks: 15A
Dip Socket: 3A
14
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interface Modules
RJ45
TS35x7.5 56mm (2.20 in.)
TS32x15 61mm (2.40 in.)
RJ45 INTERFACES CONNECTOR-TO-WIRE
35 or 32mm DIN Rail Mount
L
Technical Information
Current ..................1.5 A
Voltage ..................150V AC
Wire Range ...........0.5-4 mm2 / 20-12 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
87
m
m
43
.
(3
.)
in
SCREW CLAMP - VERTICAL - Top Entry
Part Number
5718.2
5719.2
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
RJ45
RJ45 Shielded
8
8 + 2 shield
36 (1.42)
36 (1.42)
1
1
8
8 + 2 shield
36 (1.42)
36 (1.42)
1
1
Type
No. of Poles
Module Length (L) in mm(in.)
Std. Pk.
RJ45
RJ45 Shielded
8
8 + 2 shield
36 (1.42)
36 (1.42)
1
1
8
8 + 2 shield
36 (1.42)
36 (1.42)
1
1
SCREW CLAMP - HORIZONTAL - Side Entry
5718.3
5719.3
RJ45
RJ45 Shielded
SPRING CLAMP - VERTICAL - Top Entry
Part Number
5718.2/S
5719.2/S
SPRING CLAMP - HORIZONTAL - Side Entry
5718.3/S
5719.3/S
RJ45
RJ45 Shielded
36 mm (1.42 in.)
87 mm (3.43 in.)
87 mm (3.43 in.)
36 mm (1.42 in.)
2
4
1
6
3
8
5
2
7
With Horizontal - Side Entry
RJ45 Connector
4
1
6
3
8
5
7
With Vertical - Top Entry
RJ45 Connector
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
15
Interfaces, Relay Modules and Carriers
Isolated SPDT, 35 or 32 DIN Rail
RC1 / RM1 SPDT (Single Pole Double Throw)
TS35x7.5 71 mm (2.60 in.)
TS32x15 76 mm (2.99 in.)
Isolated channels (no bus) allow control of each relay by a different logic system, if necessary. Mix sourcing
(positive switching, Vcc on/off) and sinking (negative switching, ground on/off) on a single multi-relay
module. Provide spare relay channels for future needs without committing to a specific logic power supply,
and without committing coil-drive power for more than one relay at a time.
L
Altech Relay Modules provide high density packaging of miniature general purpose relays with Single Pole
Double Throw (Form C) and Double Pole Double Throw (2 Form C) contact configurations and low current
AC and DC coils. Load your own relays in our RC Relay Carrier, or order the RM Relay Module complete with
relays.
m )
m in.
87 .43
(3
Call us with your custom module requirements!
Technical Information
• Screw-Cage Clamp Connections
• Spring Clamp Terminals
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression with DC Coil
• DIN Rail Mount, Panel Mount Available
Current ..................12 A
Voltage (max) ........250V AC / 24V DC
Wire Range ...........0.5-4 mm2 / 30-14 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
SPDT
Number of Channels
1 Channel
2 Channel
4 Channel
8 Channel
16 Channel
16
Coil Voltage
Screw terminal
Carrier Only
Module
with Relays
Part Number
Part Number
Spring terminal
Carrier Only
Module
with Relays
Part Number
Part Number
Module Length (L)
in mm (in)
12V DC
8929.5
8929.2
8929.5/S
8929.2/S
21 (0.83)
24V DC
8933.5
8933.2
8933.5/S
8933.2/S
21 (0.83)
110V AC
8935.5
8935.2
8935.5/S
8935.2/S
21 (0.83)
220V AC
8940.5
8940.2
8940.5/S
8940.2/S
21 (0.83)
12V DC
8929.6
8929.3
8929.6/S
8929.3/S
40 (1.57)
24V DC
8933.6
8933.3
8933.6/S
8933.3/S
40 (1.57)
110V AC
8935.6
8935.3
8935.6/S
8935.3/S
40 (1.57)
220V AC
8940.6
8940.3
8940.6/S
8940.3/S
40 (1.57)
12V DC
8931.5
8931.2
8931.5/S
8931.2/S
79 (3.11)
24V DC
8941.5
8941.2
8941.5/S
8941.2/S
79 (3.11)
110V AC
8942.5
8942.2
8942.5/S
8942.2/S
79 (3.11)
220V AC
8943.5
8943.2
8943.5/S
8943.2/S
79 (3.11)
12V DC
8931.6
8931.3
8931.6/S
8931.3/S
157 (6.18)
24V DC
8941.6
8941.3
8941.6/S
8941.3/S
157 (6.18)
110V AC
8942.6
8942.3
8942.6/S
8942.3/S
157 (6.18)
220V AC
8943.6
8943.3
8943.6/S
8943.3/S
157 (6.18)
12V DC
8932.5
8932.2
8932.5/S
8932.2/S
311 (12.24)
24V DC
8944.5
8944.2
8944.5/S
8944.2/S
311 (12.24)
110V AC
8946.5
8946.2
8946.5/S
8946.2/S
311 (12.24)
220V AC
8948.5
8948.2
8948.5/S
8948.2/S
311 (12.24)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interfaces, Relay Modules and Carriers
Isolated SPDT, 35 or 32 DIN Rail
RELAY PINOUT*
CONTACT SPECIFICATIONS*
SPDT
SPDT Composite Rating ....................................12A
Relay Socket.....................................................12A
Terminal Block ..................................................15A
PCB Trace for Contact Circuit
at 30°C (86°F) temperature rise NC..................12A
Common and NO ..............................................16A
PCB Trace for Coil Circuit
at 30°C (86°F) temperature rise .......................6A
Relay Contact Material......................................AgNi
Rated load (capacity) ........................................12A at 250VAC / 24VDC
Min. switching voltage ......................................5 V
Min. switching current ......................................5mA
Min. breaking capacity......................................0.3W
CONTACT CIRCUITS*
COIL SPECIFICATIONS*
Ambient Temperature........................................ -40°C-+85°C (-40°F-+185°F)
Coil Voltage
AC / DC
12 VDC
24 VDC
110 VAC
220 VAC
Coil operating range
V AC / DC
Min.
Max.
8.4
30.6
16.8
61.2
88
132
176
264
Coil Current Coil resistance
in mA
at 20°C in Ω
40
20
4.4
2.2
360
1440
8900
35500
Acceptable
resistance
± 10 %
± 10 %
± 10 %
± 10 %
COIL CIRCUITS
– +
Top View
of Module
SPDT
Top View
of Module
SPDT
AC
DC
SPDT
* For more information please see page 76 (Relay RM87)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
17
Interfaces, Relay Modules and Carriers
Isolated DPDT, 35 or 32 DIN Rail
RC2 / RM2 (Double Pole Double Throw)
TS35x7.5 71 mm (2.60 in.)
TS32x15 76 mm (2.99 in.)
L
Altech Relay Modules provide high density packaging of miniature general purpose relays with Single Pole
Double Throw (Form C) and Double Pole Double Throw (2 Form C) contact configurations and low current
AC and DC coils. Load your own relays in our RC Relay Carrier, or order the RM Relay Module complete with
relays.
m )
m in.
87 .43
(3
DPDT
Number of Channels
1 Channel
2 Channel
4 Channel
8 Channel
16 Channel
18
Isolated channels (no bus) allow control of each relay by a different logic system, if necessary. Mix sourcing
(positive switching, Vcc on/off) and sinking (negative switching, ground on/off) on a single multi-relay
module. Provide spare relay channels for future needs without committing to a specific logic power supply,
and without committing coil-drive power for more than one relay at a time.
Coil Voltage
Call us with your custom module requirements!
Technical Information
• Screw-Cage Clamp Connections
• Spring Clamp Terminals
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression with DC Coil
• DIN Rail Mount, Panel Mount Available
Current ..................8 A
Voltage (max) ........250V AC / 24V DC
Wire Range ...........0.5-4 mm2 / 30-14 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
Screw terminal
Carrier Only
Module
with Relays
Part Number
Part Number
Spring terminal
Carrier Only
Module
with Relays
Part Number
Part Number
Module Length (L)
in mm (in)
12V DC
8945.5
8945.2
8945.5/S
8945.2/S
21 (0.83)
24V DC
8951.5
8951.2
8951.5/S
8951.2/S
21 (0.83)
110V AC
8953.5
8953.2
8953.5/S
8953.2/S
21 (0.83)
220V AC
8954.5
8954.2
8954.5/S
8954.2/S
21 (0.83)
12V DC
8949.6
8949.3
8949.6/S
8949.3/S
40 (1.57)
24V DC
8951.6
8951.3
8951.6/S
8951.3/S
40 (1.57)
110V AC
8953.6
8953.3
8953.6/S
8953.3/S
40 (1.57)
220V AC
8954.6
8954.3
8954.6/S
8954.3/S
40 (1.57)
12V DC
8955.5
8955.2
8955.5/S
8955.2/S
79 (3.11)
24V DC
8956.5
8956.2
8956.5/S
8956.2/S
79 (3.11)
110V AC
8957.5
8957.2
8957.5/S
8957.2/S
79 (3.11)
220V AC
8959.5
8959.2
8959.5/S
8959.2/S
79 (3.11)
12V DC
8955.6
8955.3
8955.6/S
8955.3/S
157 (6.18)
24V DC
8956.6
8956.3
8956.6/S
8956.3/S
157 (6.18)
110V AC
8957.6
8957.3
8957.6/S
8957.3/S
157 (6.18)
220V AC
8959.6
8959.3
8959.6/S
8959.3/S
157 (6.18)
12V DC
8963.5
8963.2
8963.5/S
8963.2/S
311 (12.24)
24V DC
8972.5
8972.2
8972.5/S
8972.2/S
311 (12.24)
110V AC
8995.5
8995.2
8995.5/S
8995.2/S
311 (12.24)
220V AC
8999.5
8999.2
8999.5/S
8999.2/S
311 (12.24)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interfaces, Relay Modules and Carriers
Isolated DPDT, 35 or 32 DIN Rail
RELAY PINOUT*
SPDT
CONTACT SPECIFICATIONS*
DPDT Rating .....................................................8A
Relay Socket.....................................................8A
Terminal Block ..................................................15A
PCB Trace for Contact Circuit
at 30°C (86°F) temperature rise NC..................10A
PCB Trace for Coil Circuit
at 30°C (86°F) temperature rise .......................2A
Relay Contact Material......................................AgNi
Rated load (capacity) ........................................8A at 250VAC / 24VDC
Min. switching voltage ......................................5 V
Min. switching current ......................................5mA
Min. breaking capacity......................................0.3W
CONTACT CIRCUITS*
COIL SPECIFICATIONS*
Ambient Temperature........................................ -40°C-+85°C (-40°F-+185°F)
Coil Voltage
AC / DC
12 VDC
24 VDC
110 VAC
220 VAC
Coil operating range
V AC / DC
Min.
Max.
8.4
30.6
16.8
61.2
88
132
176
264
Coil Current Coil resistance
in mA
at 20°C in Ω
40
20
4.4
2.2
360
1440
8900
35500
Acceptable
resistance
± 10 %
± 10 %
± 10 %
± 10 %
COIL CIRCUITS
– +
Top View
of Module
SPDT
Top View
of Module
SPDT
AC
DC
DPDT
* For more information please see page 76 (Relay RM84)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
19
Interfaces, Relay Modules and Carriers
Bussed SPDT, 35 or 32 DIN Rail
RC1 / RM1 (Single Pole Double Throw)
TS35x7.5 71 mm (2.80 in.)
TS32x15 76 mm (2.50 in.)
Altech Bussed Relay Modules provide high density packaging of miniature general purpose relays with
minimal hook-up wiring. Select from bussed DC Positive (DC Negative switching), bussed DC Negative (DC
Positive switching), or bussed AC neutral.
Ideal for traditional mechanical relay input/output array between a single logic system and peripheral
devices, or between logic systems in a network as well as their peripheral and field devices.
L
Load your own relays in our RCB Relay Carrier, or order the RMB Relay Module complete with 8 or 16 relays.
Call us with your custom module requirements!
m
m in.)
87 43
.
(3
• Screw-Cage Clamp Connections
• Spring Clamp Terminals
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression With DC Coil
• DIN Rail Mount, Panel Mount Available
SPDT
Screw terminal
Carrier Only
Technical Information
Current ..................12 A
Voltage (max) ........250V AC / 24V DC
Wire Range ...........0.5-4 mm2 / 30-14 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
Spring terminal
Carrier Only
Module
with Relays
Part Number
Part Number
Number of Channels
Coil Voltage
Part Number
Module
with Relays
Part Number
8 Channel, Bussed DC+
12V DC ( E)
8912.5
8912.2
8912.5/S
8912.2/S
125 (4.92)
24V DC (G)
5494.5
5494.2
5494.5/S
5494.2/S
125 (4.92)
12V DC ( E)
8912.6
8912.3
8912.6/S
8912.3/S
125 (4.92)
24V DC (G)
5492.5
5492.2
5492.5/S
5492.2/S
125 (4.92)
110V AC (U)
5502.5
5502.2
5502.5/S
5502.2/S
125 (4.92)
220V AC (X)
8913.6
8913.3
8913.6/S
8913.3/S
125 (4.92)
12V DC ( E)
8914.5
8914.2
8914.5/S
8914.2/S
248 (9.76)
24V DC (G)
5508.5
5508.2
5508.5/S
5508.2/S
248 (9.76)
12V DC ( E)
8921.5
8921.2
8921.5/S
8921.2/S
248 (9.76)
24V DC (G)
5506.5
5506.2
5506.5/S
5506.2/S
248 (9.76)
110V AC (U)
5514.5
5514.2
5514.5/S
5514.2/S
248 (9.76)
220V AC (X)
5514.6
5514.3
5514.6/S
5514.3/S
248 (9.76)
8 Channel, Bussed DC-
8 Channel, Bussed AC (N)
16 Channel, Bussed DC+
16 Channel, Bussed DC-
16 Channel, Bussed AC(N)
20
Module Length (L)
in mm (in)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interfaces, Relay Modules and Carriers
Bussed SPDT, 35 or 32 DIN Rail
CONTACT SPECIFICATIONS*
RELAY PINOUT*
SPDT Composite Rating ....................................12A
Relay Socket.....................................................12A
Terminal Block ..................................................15A
PCB Trace for Contact Circuit
at 30°C (86°F) temperature rise NC..................12A
PCB Trace for Coil Circuit
at 30°C (86°F) temperature rise .......................4A
PCB Trace for Bus
at 30°C (86°F) temperature rise .......................16A
Relay Contact Material......................................AgNi
Rated load (capacity) ........................................12A at 250VAC / 24VDC
Min. switching voltage ......................................5 V
Min. switching current ......................................5mA
Min. breaking capacity......................................0.3W
SPDT
CONTACT CIRCUITS*
COIL SPECIFICATIONS*
Pin Numbers
(see pinout)
2
Ambient Temperature........................................ -40°C-+85°C (-40°F-+185°F)
Coil Voltage
AC / DC
Coil operating range
V AC / DC
Min.
Max.
8.4
30.6
16.8
61.2
88
132
176
264
12 VDC
24 VDC
110 VAC
220 VAC
Coil Current Coil resistance
in mA
at 20°C in Ω
40
20
4.4
2.2
360
1440
8900
35500
6
4
Acceptable
resistance
± 10 %
± 10 %
± 10 %
± 10 %
Repeats For
More Relays
NC NO C NC NO C NC
COIL CIRCUITS
DC Coil Circuit
Bussed DC Positive
(Negative Switching)
DC Coil Circuit
Bussed DC Negative or
(Positive Switching)
BUS
BUS
Coil Circuit
Repeats for
Additional
Relays
Coil Circuit
Repeats for
Additional
Relays
Circuit View
Is From Top
9 N N
8
2 1 N N
Coil
Terminals
16
3
2
Negative Bussed
AC Coil Circuit
Bussed Neutral
1
– –
BUS
Positive Bussed
+ +
1
2
3
4
Bipolar
RELAYS
NC NO C NC NO C NC
Coil Circuit
Repeats for
Additional
Relays
Contact
Terminals
* For more information please see page 76 (Relay RM87)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
21
Interfaces, Relay Modules and Carriers
Bussed DPDT, 35 or 32 DIN Rail
RC2 / RM2 (Double Pole Double Throw)
TS35x7.5 71 mm (2.80 in.)
TS32x15 76 mm (2.50 in.)
Altech Bussed Relay Modules provide high density packaging of miniature general purpose relays with
minimal hook-up wiring. Select from bussed DC Positive (DC Negative switching), bussed DC Negative (DC
Positive switching), or bussed AC neutral.
Ideal for traditional mechanical relay input/output array between a single logic system and peripheral
devices, or between logic systems in a network as well as their peripheral and field devices.
L
Load your own relays in our RCB Relay Carrier, or order the RMB Relay Module complete with 8 or 16 relays.
Call us with your custom module requirements!
m
m in .)
87 43
.
(3
• Screw-Cage Clamp Connections
• Spring Clamp Terminals
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression With DC Coil
• DIN Rail Mount, Panel Mount Available
DPDT
Screw terminal
Carrier Only
Technical Information
Current ..................8 A
Voltage (max) ........250V AC / 24V DC
Wire Range ...........0.5-4 mm2 / 30-14 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
Spring terminal
Carrier Only
Module
with Relays
Part Number
Part Number
Number of Channels
Coil Voltage
Part Number
Module
with Relays
Part Number
8 Channel, Bussed DC+
12V DC ( E)
8923.5
8923.2
8923.5/S
8923.2/S
125 (4.92)
24V DC (G)
8924.5
8924.2
8924.5/S
8924.2/S
125 (4.92)
12V DC ( E)
8923.6
8923.3
8923.6/S
8923.3/S
125 (4.92)
24V DC (G)
8924.6
8924.4
8924.6/S
8924.4/S
125 (4.92)
110V AC (U)
8925.5
8925.2
8925.5/S
8925.2/S
125 (4.92)
220V AC (X)
8925.6
8925.3
8925.6/S
8925.3/S
125 (4.92)
12V DC ( E)
8926.5
8926.2
8926.5/S
8926.2/S
248 (9.76)
24V DC (G)
8926.6
8926.3
8926.6/S
8926.3/S
248 (9.76)
12V DC ( E)
8927.5
8927.2
8927.5/S
8927.2/S
248 (9.76)
24V DC (G)
8927.6
8927.3
8927.6/S
8927.3/S
248 (9.76)
110V AC (U)
8928.5
8928.2
8928.5/S
8928.2/S
248 (9.76)
220V AC (X)
8928.6
8928.3
8928.6/S
8928.3/S
248 (9.76)
8 Channel, Bussed DC-
8 Channel, Bussed AC (N)
16 Channel, Bussed DC+
16 Channel, Bussed DC-
16 Channel, Bussed AC(N)
22
Module Length (L)
in mm (in)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interfaces, Relay Modules and Carriers
Bussed DPDT, 35 or 32 DIN Rail
CONTACT SPECIFICATIONS*
RELAY PINOUT*
DPDT Rating .....................................................8A
Relay Socket.....................................................8A
Terminal Block ..................................................15A
PCB Trace for Contact Circuit
at 30°C (86°F) temperature rise NC..................8A
PCB Trace for Coil Circuit
at 30°C (86°F) temperature rise .......................2A
PCB Trace for Bus
at 30°C (86°F) temperature rise .......................16A
Relay Contact Material......................................AgNi
Rated load (capacity) ........................................8A at 250VAC / 24VDC
Min. switching voltage ......................................5 V
Min. switching current ......................................5mA
Min. breaking capacity......................................0.3W
CONTACT CIRCUITS*
COIL SPECIFICATIONS*
Ambient Temperature........................................ -40°C-+85°C (-40°F-+185°F)
Pin Numbers
(see pinout)
2
3
Coil Voltage
AC / DC
Coil operating range
V AC / DC
Min.
Max.
8.4
30.6
16.8
61.2
88
132
176
264
12 VDC
24 VDC
110 VAC
220 VAC
Coil Current Coil resistance
in mA
at 20°C in Ω
40
20
4.4
2.2
3 4 2
Acceptable
resistance
360
1440
8900
35500
6
C NO NC Repeats
± 10 %
± 10 %
± 10 %
± 10 %
7
4
C NO NC Repeats
C NO NC
5
6 5 7
C NO NC
COIL CIRCUITS
DC Coil Circuit
Bussed DC Negative or
(Positive Switching)
DC Coil Circuit
Bussed DC Positive
(Negative Switching)
+15 +14
+2 +1
– –
+8 +7
+2 +1
– –
BUS
BUS
Coil Circuit
Repeats for
Additional
Relays
Coil Circuit
Repeats for
Additional
Relays
Circuit View
Is From Top
AC Coil Circuit
Bussed Neutral
10 9
N N
8 7
2 1
N N
Coil
Terminals
16 15
4
3
2
Negative Bussed
1
– –
Positive Bussed
BUS
+ +
1
2
3
4
Coil Circuit
Repeats for
Additional
Relays
RELAYS
C NO NC C NO NC C NO NC
C NO NC C NO NC C NO NC
Contact
Terminals
* For more information please see page 76 (Relay RM84)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
23
Interfaces, High Current Isolated
Isolated Channels - 16 Amp, 35 or 32 DIN Rail
RMH1 - 1 Channel (Single Pole Double Throw)
TS35x7.5 70 mm (2.75 in.)
TS32x15 75 mm (2.95 in.)
L
A true high-current rating in a DIN Rail mount miniature relay module. The miniature relays used in the
Altech RMH have a SPDT (Form C) 16 Amp continuous current rating, developed from dual 8 Amp contacts
that are internally connected in parallel. The relay socket is rated dual 8 Amp. Printed circuit traces are
balanced, rated 16 Amp and connect to Altech terminal blocks UL rated 15A/300V.
Typical relay specifications combined with other module component ratings give module ratings suitable
for many control applications.
87
• Screw-Cage Clamp Connection
• Spring Clamp Terminals
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression With DC Coils
• Industry Standard Relaysa
• DIN Rail Mount, Panel Mount Available
m
m
n.)
3i
4
(3.
SPDT
Technical Information
Current ..................16 A
Voltage (max) ........250V AC / 24V DC
Wire Range ...........0.5-4 mm2 / 30-14 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
Coil Voltage
Screw terminal
Part Number
Spring terminal
Part Number
LED (2mA)
Module Length (L)
in mm (in)
1 Channel
5V DC
8905.2
8905.2/S
Yellow
21 (0.83)
1 Channel
6V DC
8906.2
8906.2/S
Green
21 (0.83)
1 Channel
12V DC
8907.2
8907.2/S
Red
21 (0.83)
1 Channel
24V DC
5800.2
5800.2/S
Yellow
21 (0.83)
1 Channel
48V DC
5802.2
5802.2/S
Green
21 (0.83)
1 Channel
60V DC
8908.2
8908.2/S
Red
21 (0.83)
1 Channel
110V DC
5803.2
5803.2/S
Red
21 (0.83)
Coil Voltage
Screw terminal
Part Number
Spring terminal
Part Number
LED (2mA)
Module Length (L)
in mm (in)
1 Channel
6V AC
8909.2
8909.2/S
Green
21 (0.83)
1 Channel
12V AC
8910.2
8910.2/S
Red
21 (0.83)
1 Channel
24V AC
5801.2
5801.2/S
Red
21 (0.83)
1 Channel
50V AC
8911.2
8911.2/S
Red
21 (0.83)
1 Channel
110V AC
5804.2
5804.2/S
Yellow
21 (0.83)
1 Channel
220V AC
5805.2
5805.2/S
Green
21 (0.83)
1 Channel
240V AC
5806.2
5806.2/S
Red
21 (0.83)
DC
SPDT
AC
24
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interfaces, High Current Isolated
Isolated Channels - 16 Amp, 35 or 32 DIN Rail
RELAY PINOUT*
GENERAL RELAY SPECIFICATIONS*
Mechanical Life (cycles)....................................> 3 x 107
Max operating frequency
• at rated load.................................................600 cycles/hour
• no load .........................................................72000 cycles/hour
Operating / release time ...................................7 ms/ 3 ms
COIL SPECIFICATIONS*
Contact material ...............................................AgNi
Rated load ( capacity) .......................................16A at 250V AC / 24 V DC
Max. breaking capacity .....................................4000 VA
Min. breaking capacity......................................0.3 W
Electrical life ( resistive AC1).............................> 0.7 x 105
Coil Voltage
AC / DC
5.0
6.0
12.0
24.0
48.0
60.0
110.0
Coil operating range
V AC / DC
Min.
Max.
3.5
12.7
4.2
15.3
8.4
30.6
16.8
61.2
33.6
122.4
42.0
153.0
77.0
280.0
Coil Current Coil resistance
in mA
at 20°C in Ω
96.0
80.0
40.0
20.0
10.0
8.0
4.4
60.0
90.0
360.0
1,440.0
5,700.0
7,500.0
25,200.0
CONTACT CIRCUITS*
Acceptable
resistance
± 10 %
± 10 %
± 10 %
± 10 %
± 10 %
± 10 %
± 10 %
COIL CIRCUITS
AC COIL CIRCUIT
DC COIL CIRCUIT
* For more information please see page 76 (Relay RM85)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
25
Interfaces, High Current Isolated
Isolated Channels - 16 Amp, 35 or 32 DIN Rail
RMH4 - 4 Channel (Single Pole Double Throw)
TS35x7.5 71 mm (2.80 in.)
TS32x15 76 mm (2.50 in.)
A true high-current rating in a DIN Rail mount miniature relay module. The miniature relays used in the
Altech RMH have a SPDT (Form C) 16 Amp continuous current rating, developed from dual 8 Amp contacts
that are internally connected in parallel. The relay socket is rated dual 8 Amp. Printed circuit traces are
balanced, rated 16 Amp and connect to Altech terminal blocks UL rated 15A/300V.
Typical relay specifications combined with other module component ratings give module ratings suitable
for many control applications.
L
m
m n.)
87 43 i
.
(3
• Screw-Cage Clamp Connection
• Spring Clamp Terminals
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression With DC Coils
• Industry Standard Relaysa
• DIN Rail Mount, Panel Mount Available
SPDT
Technical Information
Current ..................16 A
Voltage (max) ........250V AC / 24V DC
Wire Range ...........0.5-4 mm2 / 30-14 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
Coil Voltage
Screw terminal
Part Number
Spring terminal
Part Number
4 Channel
5V DC
8905.3
8905.3/S
Yellow
79 (3.11)
4 Channel
6V DC
8906.3
8906.3/S
Green
79 (3.11)
4 Channel
12V DC
8907.3
8907.3/S
Red
79 (3.11)
4 Channel
24V DC
5800.3
5800.3/S
Yellow
79 (3.11)
4 Channel
48V DC
5802.3
5802.3/S
Green
79 (3.11)
4 Channel
60V DC
8908.3
8908.3/S
Red
79 (3.11)
4 Channel
110V DC
5803.3
5803.3/S
Red
79 (3.11)
Coil Voltage
Screw terminal
Part Number
Spring terminal
Part Number
LED (2mA)
Module Length (L)
in mm (in)
4 Channel
6V AC
8909.3
8909.3/S
Green
79 (3.11)
4 Channel
12V AC
8910.3
8910.3/S
Red
79 (3.11)
4 Channel
24V AC
5801.3
5801.3/S
Red
79 (3.11)
4 Channel
50V AC
8911.3
8911.3/S
Red
79 (3.11)
4 Channel
110V AC
5804.3
5804.3/S
Yellow
79 (3.11)
4 Channel
220V AC
5805.3
5805.3/S
Green
79 (3.11)
4 Channel
240V AC
5806.3
5806.3/S
Red
79 (3.11)
DC
SPDT
AC
26
LED (2mA)
Module Length (L)
in mm (in)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interfaces, High Current Isolated
Isolated Channels - 16 Amp, 35 or 32 DIN Rail
RELAY PINOUT*
GENERAL RELAY SPECIFICATIONS*
Mechanical Life (cycles)....................................> 3 x 107
Max operating frequency
• at rated load.................................................600 cycles/hour
• no load .........................................................72000 cycles/hour
Operating / release time ...................................7 ms/ 3 ms
COIL SPECIFICATIONS*
Contact material ...............................................AgNi
Rated load ( capacity) .......................................16A at 250V AC / 24 V DC
Max. breaking capacity .....................................4000 VA
Min. breaking capacity......................................0.3 W
Electrical life ( resistive AC1).............................> 0.7 x 105
Coil Voltage
AC / DC
5.0
6.0
12.0
24.0
48.0
60.0
110.0
Coil operating range
V AC / DC
Min.
Max.
3.5
12.7
4.2
15.3
8.4
30.6
16.8
61.2
33.6
122.4
42.0
153.0
77.0
280.0
Coil Current Coil resistance
in mA
at 20°C in Ω
96.0
80.0
40.0
20.0
10.0
8.0
4.4
60.0
90.0
360.0
1,440.0
5,700.0
7,500.0
25,200.0
CONTACT CIRCUITS*
Acceptable
resistance
± 10 %
± 10 %
± 10 %
± 10 %
± 10 %
± 10 %
± 10 %
COIL CIRCUITS
AC COIL CIRCUIT
DC COIL CIRCUIT
* For more information please see page 76 (Relay RM85)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
27
Safety Relay Modules
Isolated Channels - 8 Amp Contacts, 35 or 32 DIN Rail
Isolated Channel (Double Pole Double Throw)
TS35x7.5 71 mm (2.80 in.)
TS32x15 76 mm (2.99 in.)
L
Altech Safety Relay Modules utilize Relays with Force-Guided-Contacts that meet or
exceed international standards, TÜV and UL. They are designed to protect man and
machine as specified in OSHA FR1910 Regulations, a mandatory requirement of the
European Machinery Directive EMD 89.392 EEC. The Safety Relays are used in Safety
Devices such as Emergency Stop Modules, Safety Gate Monitors, 2-Hand Safety Modules, etc.
This series of Safety Relay Modules are Double Pole, Double Throw configurations, and are
available as 1, 2, 4, 8 and 16 isolated channels and 8 and 16 bussed channels with 12 or 24
VDC coils. Isolated channels allow control of each relay by a different logic system, if
necessary. There are two inputs for each relay coil per channel. Bussed channels allow high
density packaging with a common input for all relays.Safety Relay Modules may be ordered
with three different types of relay contact material, depending on the actual load current.
m )
m in.
87 .43
(3
•
•
•
•
•
•
DPDT
Isolated Channel
(no bus)
1 Channel
1 Channel
2 Channel
2 Channel
4 Channel
4 Channel
8 Channel
8 Channel
16 Channel
16 Channel
28
Screw-Cage Clamp Connection
LED Coil Voltage Indicator
Reverse DC Polarity LED Protection
Surge Suppression With DC Coils
Industry Standard Relays
DIN Rail Mount, Panel Mount Available
Contact Material:Contact Material:
AgSnO2+0.2µmAu
Coil Voltage
12V
24V
12V
24V
12V
24V
12V
24V
12V
24V
Contact Material:
AgNi10+0.2µmAu
AgNi10+5µmAu
Contact Ratings:
8A(2x5A) 250VDC, 400VAC
Contact Ratings:
8A(2x5A) 250VDC, 400VAC
Contact Ratings:
8A(2x5A) 250VDC, 400VAC
Part Number
8949.2C
8951.2C
8949.3C
8951.3C
8955.2C
8956.2C
8955.3C
8956.3C
8963.2C
8972.2C
Part Number
8949.2N
8951.2N
8949.3N
8951.3N
8955.2N
8956.2N
8955.3N
8956.3N
8963.2N
8972.2N
Part Number
8949.2S
8951.2S
8949.3S
8951.3S
8955.2S
8956.2S
8955.3S
8956.3S
8963.2S
8972.2S
Module Length (L)
in mm (in)"
21 (0.83)
21 (0.83)
40 (1.57)
40 (1.57)
79 (3.11)
79 (3.11)
157 (6.18)
157 (6.18)
311 (12.24)
311 (12.24)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Safety Relay Modules
Isolated Channels - 8 Amp Contacts, 35 or 32 DIN Rail
Relay Pinout
Relay Specifications
-Normal Coil Voltage:
-Coil Power Dissipation:
-Max. Switching Voltage:
-Max. Switching Current:
12,24 VDC
0.7W
250 VDC, 400 AC
8A(2x5A simultaneous)
-Max. Switching Power
DC
200W (2x160W simultaneous)
AC
2000VA (2x1250VA simultaneous)
-Contact Switching Rate:
-Relay Operate Time
-Relay Release Time
-Contact Arrangements
10 operations/ sec.
≤15 ms
≤12 ms
DPDT, 2 FORM C
-Contact Material:
Standard
Optional
AgNi10+0.2µmAu
AgSnO2+0.2µmAu
AgNi10+5µmAu
Coil Circuits
-Mechanical Life:
-Ambient Temperature:
-Cover Material:
-Weight:
≥50x106 operation cycles
-40°+ 70°C
Polyamide 6
15g
Coil Specifications
Rated
Voltage
12VDC
24VDC
Voltage
Range
9.6V-19.2V
19.2V-38.4V
Coil
Resistance
210Ω ± 10%
820Ω ± 10%
Top View
of Module
DPDT
Contact Circuits
3 4
2
C NO NC Repeats
C NO NC Repeats
6 5
7
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
29
Safety Relay Modules
Bussed Channels - 8 Amp Contacts, 35 or 32 DIN Rail
TS35x7.5 71 mm (2.80 in.)
TS32x15 76 mm (2.50 in.)
L
Bussed Channel (Double Pole Double Throw)
Altech Safety Relay Modules utilize Relays with Force-Guided-Contacts that meet or
exceed international standards, TÜV and UL. They are designed to protect man and
machine as specified in OSHA FR1910 Regulations, a mandatory requirement of the
European Machinery Directive EMD 89.392 EEC. The Safety Relays are used in Safety
Devices such as Emergency Stop Modules, Safety Gate Monitors, 2-Hand Safety Modules, etc.
This series of Safety Relay Modules are Double Pole, Double Throw configurations, and are
available as 1, 2, 4, 8 and 16 isolated channels and 8 and 16 bussed channels with 12 or 24
VDC coils. Isolated channels allow control of each relay by a different logic system, if
necessary. There are two inputs for each relay coil per channel. Bussed channels allow high
density packaging with a common input for all relays.Safety Relay Modules may be ordered
with three different types of relay contact material, depending on the actual load current.
m
m n.)
87 3 i
.4
(3
•
•
•
•
•
•
DPDT
Screw-Cage Clamp Connection
LED Coil Voltage Indicator
Reverse DC Polarity LED Protection
Surge Suppression With DC Coils
Industry Standard Relays
DIN Rail Mount, Panel Mount Available
Contact Material:Contact Material:
AgSnO2+0.2µmAu
Contact Material:
AgNi10+0.2µmAu
AgNi10+5µmAu
Contact Ratings:
8A(2x5A) 250VDC, 400VAC
Contact Ratings:
8A(2x5A) 250VDC, 400VAC
Contact Ratings:
8A(2x5A) 250VDC, 400VAC
Part Number
8923.2C
8924.2C
8923.3C
8924.4C
8926.2C
8926.3C
8927.2C
8927.3C
Part Number
8923.2N
8924.2N
8923.3N
8924.4N
8926.2N
8926.3N
8927.2N
8927.3N
Part Number
8923.2S
8924.2S
8923.3S
8924.4S
8926.2S
8926.3S
8927.2S
8927.3S
Bussed Channels
8 Channel, DC+
8 Channel, DC+
8 Channel, DC8 Channel, DC16 Channel, DC+
16 Channel, DC+
16 Channel, DC16 Channel, DC-
30
Coil Voltage
12V
24V
12V
24V
12V
24V
12V
24V
Module Length (L)
in mm (in)"
125 (4.92)
125 (4.92)
125 (4.92)
125 (4.92)
248 (9.76)
248 (9.76)
248 (9.76)
248 (9.76)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Safety Relay Modules
Bussed Channels - 8 Amp Contacts, 35 or 32 DIN Rail
Relay Pinout
Relay Specifications
-Normal Coil Voltage:
-Coil Power Dissipation:
-Max. Switching Voltage:
-Max. Switching Current:
PIN DIAMETER
1.3mm, +0.1, –0.0
(0.051 in. +0.004, –0.0)
4
5
3
6
2
7
1
8
10mm
(0.39 in.)
12,24 VDC
0.7W
250 VDC, 400 AC
8A(2x5A simultaneous)
-Max. Switching Power
DC
200W (2x160W simultaneous)
AC
2000VA (2x1250VA simultaneous)
20mm
(0.79 in.)
-Contact Switching Rate:
-Relay Operate Time
-Relay Release Time
-Contact Arrangements
7.5mm
(0.30 in.)
10 operations/ sec.
≤15 ms
≤12 ms
DPDT, 2 FORM C
-Contact Material:
Standard
Optional
Coil Circuits
DC Coil Circuit
Bussed DC Negative or
(Positive Switching)
AgNi10+0.2µmAu
AgSnO2+0.2µmAu
AgNi10+5µmAu
-Mechanical Life:
-Ambient Temperature:
-Cover Material:
-Weight:
DC Coil Circuit
Bussed DC Positive
(Negative Switching)
≥50x106 operation cycles
-40°+ 70°C
Polyamide 6
15g
+15 +14
+2 +1
– –
+8 +7
+2 +1
BUS
BUS
Coil Circuit
Repeats for
Additional
Relays
Coil Circuit
Repeats for
Additional
Relays
Coil Specifications
Rated
Voltage
12VDC
24VDC
Voltage
Range
9.6V-19.2V
19.2V-38.4V
Coil
Resistance
210Ω ± 10%
820Ω ± 10%
Circuit View
Is From Top
Coil
Terminals
4
3
2
Negative Bussed
1
– –
Positive Bussed
+ +
1
2
3
4
RELAYS
C NO NC C NO NC C NO NC
C NO NC C NO NC C NO NC
Contact
Terminals
Contact Circuits
3 4
2
C NO NC Repeats
C NO NC Repeats
6 5
7
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
31
– –
Safety Relay Modules
4 Pole Relays - 8 Amp, 35 or 32 DIN Rail
TS35x7.5 76mm (2.99 in.)
TS32x15 81mm (3.19 in.)
L
4 Pole, 8 Amp
Altech Safety Relay Modules utilize Relays with Force-Guided-Contacts that meet or
exceed international standards, TÜV and UL. They are designed to protect man and
machine as specified in OSHA CFR1910 Regulations, which is a mandatory requirement of
the European Machinery Directive EMD 89.392 EEC.
•
•
•
•
•
Screw-Cage clamp Connections
LED Coil Voltage Indicator
Reverse DC Polarity LED Protection
Surge Suppression With DC Coil
Din Rail Mount, Panel Mount Available
m )
m n.
0 i
2 2
1 .7
(4
Altech Safety Relays are electro-mechanical relays that are mechanically linked together,
causing all contacts to move together when the coil is energized. Force-Guided-contacts
are also known as positive-guided-contacts, captive contacts or locked contacts. In
addition, our Safety Relays have Crown Contacts which provide two locations per contacts
to improve switching conditions. The Safety Relays are used in Safety Devices such as
Emergency Stop Modules, Safety Gate Monitors, 2-Hand Safety Modules, Safety Light
Curtains, etc.
This series of Safety Relay Modules consist of 4 pole relays with two choices of
configurations (2NO/2NC or 3NO/1NC), with 8 or 10 Amp contacts, and are available as 1,2,
and 4 isolated channels with 12, or 24 VDC coils. Isolated channels allows control of each
relay by a different logic system, if necessary. There are two inputs for each relay coil per
channel. Safety Relay Modules may be ordered with three different types of relay contact
material, depending on the actual load current. The part numbers shown in this data sheet
are for our standard contact material, which is AgSn02 + 0.2µmAu.
Contact Material*:
AgSnO2 + 0.2µmAu
Contact Ratings:
8A 250VDC, 400VAC
Contact Ratings:
1 Channel
1 Channel
2 Channel
2 Channel
4 Channel
4 Channel
Coil Voltage
12V
24V
12V
24V
12V
24V
2N.0 + 2N.C
3N.0 + 1N.C
Part Number
156.0A11.1222C
156.0A11.2422C
256.0A11.1222C
256.0A11.2422C
456.0A11.1222C
456.0A11.2422C
Part Number
156.0A11.1231C
156.0A11.2431C
256.0A11.1231C
256.0A11.2431C
456.0A11.1231C
456.0A11.2431C
Module Length (L)
in mm (in)"
40.10 (1.58)
40.10 (1.58)
78.20 (3.08)
78.20 (3.08)
154.40 (6.08)
154.40 (6.08)
* Note: Additional relay contact materials are available upon request. Please contact Altech for additional information.
32
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Safety Relay Modules
4 Pole Relays - 8 Amp, 35 or 32 DIN Rail
4 Pole, 8 Amp
DC Coil Circuits
Relay Specifications - 8 Amps
-Normal Coil Voltage:
-Coil Power Dissipation:
-Max. Switching Voltage:
-Max. Switching Current:
12,24 VDC
0.6W
250VDC, 400VAC
8A
-Max. Switching Power
DC
AC
200W
2000VA
-Contact Switching Rate:
-Relay Operate Time
-Relay Release Time
-Contact Arrangements
10 operations/ sec.
20 ms
6 ms
2NO/2NC, 3NO/1NC
-Contact Material:
Standard
Optional
AgSnO2+0.2µmAu
AgNi10+0.2µmAu
AgNi10+5µmAu
Contact Circuits
-Mechanical Life:
-Ambient Temperature:
-Cover Material:
-Weight:
≥50x106 operation cycles
-40°+ 85°C
Thermoplast
35g
Coil Specifications
Top View
of Module
Rated
Voltage
12VDC
24VDC
Voltage
Range
8.4V-16.8V
16.8V-33.6V
Coil
Resistance
240Ω ± 10%
960Ω ± 10%
5 6 7 8
1 2 3 4
Relay Configurations
2 N.O + 2 N.C
NO Pin (1,2), (5,6)
NC Pin (3,4), (7,8)
3 N.O + 1 N.C
NO Pin (1,2), (5,6), (7,8)
NC Pin (3,4)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
33
Safety Relay Modules
4 Pole Relays - 10 Amp, 35 or 32 DIN Rail
4 Pole, 10 Amp
TS35x7.5 84.2mm (3.31 in.)
TS32x15 89.2mm (3.50 in.)
L
Altech Safety Relay Modules utilize Relays with Force-Guided-Contacts that meet or
exceed international standards, TÜV and UL. They are designed to protect man and
machine as specified in OSHA CFR1910 Regulations, which is a mandatory requirement of
the European Machinery Directive EMD 89.392 EEC.
•
•
•
•
•
Screw-Cage clamp Connections
LED Coil Voltage Indicator
Reverse DC Polarity LED Protection
Surge Suppression With DC Coil
Din Rail Mount, Panel Mount Available
m
m .)
0 in
12 .72
(4
Altech Safety Relays are electro-mechanical relays that are mechanically linked together,
causing all contacts to move together when the coil is energized. Force-Guided-contacts
are also known as positive-guided-contacts, captive contacts or locked contacts. In
addition, our Safety Relays have Crown Contacts which provide two locations per contacts
to improve switching conditions. The Safety Relays are used in Safety Devices such as
Emergency Stop Modules, Safety Gate Monitors, 2-Hand Safety Modules, Safety Light
Curtains, etc.
This series of Safety Relay Modules consist of 4 pole relays with two choices of
configurations (2NO/2NC or 3NO/1NC), with 8 or 10 Amp contacts, and are available as 1,2,
and 4 isolated channels with 12, or 24 VDC coils. Isolated channels allows control of each
relay by a different logic system, if necessary. There are two inputs for each relay coil per
channel. Safety Relay Modules may be ordered with three different types of relay contact
material, depending on the actual load current. The part numbers shown in this data sheet
are for our standard contact material, which is AgSn02 + 0.2µmAu.
Contact Material*:
AgSnO2 + 0.2µmAu
Contact Ratings:
10A 250VDC, 400VAC
Contact Ratings:
1 Channel
1 Channel
2 Channel
2 Channel
4 Channel
4 Channel
Coil Voltage
12V
24V
12V
24V
12V
24V
2N.0 + 2N.C
3N.0 +1N.C
Part Number
156.0A01.1222C
156.0A01.2422C
256.0A01.1222C
256.0A01.2422C
456.0A01.1222C
456.0A01.2422C
Part Number
156.0A01.1231C
156.0A01.2431C
256.0A01.1231C
256.0A01.2431C
456.0A01.1231C
456.0A01.2431C
Module Length (L)
in mm (in)"
40.10 (1.58)
40.10 (1.58)
78.20 (3.08)
78.20 (3.08)
154.40 (6.08)
154.40 (6.08)
* Note: Additional relay contact materials are available upon request. Please contact Altech for additional information.
34
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Safety Relay Modules
4 Pole Relays - 10 Amp, 35 or 32 DIN Rail
4 Pole, 10 Amp
DC Coil Circuits
Relay Specifications - 10 Amps
-Normal Coil Voltage:
-Coil Power Dissipation:
-Max. Switching Voltage:
-Max. Switching Current:
12,24 VDC
0.75W
250VDC, 400VAC
10A
-Max. Switching Power
DC
AC
240W
2500VA
-Contact Switching Rate:
-Relay Operate Time
-Relay Release Time
-Contact Arrangements
10 operations/ sec.
27 ms
5 ms
2NO/2NC, 3NO/1NC
-Contact Material:
Standard
Optional
AgSnO2+0.2µmAu
AgNi10+0.2µmAu
AgNi10+5µmAu
Contact Circuits
-Mechanical Life:
-Ambient Temperature:
-Cover Material:
-Weight:
>30x106 operation cycles
-40°+ 80°C
Thermoplast
75g
Coil Specifications
Top View
of Module
Rated
Voltage
12VDC
24VDC
Voltage
Range
8.4V-19.2V
16.8V-38.4V
Coil
Resistance
192Ω ± 10%
770Ω ± 10%
5 6 7 8
1 2 3 4
Relay Configurations
2 N.O + 2 N.C
NO Pin (3,4), (7,8)
NC Pin (1,2), (5,6)
3 N.O + 1 N.C
NO Pin (3,4), (5,6), (7,8)
NC Pin (1,2)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
35
Safety Relay Modules
6 Pole Relays - 8 Amp, 35 or 32 DIN Rail
6 Pole, 8 Amp
TS35x7.5 76mm (2.99 in.)
TS32x15 81mm (3.19 in.)
L
Altech Safety Relay Modules utilize Relays with Force-Guided-Contacts that meet or
exceed international standards, TÜV, CSA, CE, UKCA, and UL (relay only). They are
designed to protect man and machine as specified in OSHA CFR1910 Regulations,
which is a mandatory requirement of the European Machinery Directive EMD 89.392
EEC.
• Screw-Cage clamp Connections
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression With DC Coil
• Din Rail Mount, Panel Mount Available
m
m )
0 in.
12 .72
(4
Altech Safety Relays are electro-mechanical relays that are mechanically linked
together, causing all contacts to move together when the coil is energized. ForceGuided-contacts are also known as positive-guided-contacts, captive contacts or
locked contacts. In addition, our Safety Relays have Crown Contacts which provides
two locations per contacts to improve switching conditions. The Safety Relays are
used in Safety Devices such as Emergency Stop Modules, Safety Gate Monitors, 2Hand Safety Modules, Safety Light Curtains, etc.
Contact Ratings:
8A 250VDC,400VAC
This series of Safety Relay Modules consist of 6 pole relays with three configuration
choices (2NO+4NC, 3NO+3NC, 4NO+2NC, 5NO+1NC), 8 or 10 Amp contacts and
either 1, 2 and 4 isolated channels with 12 or 24 VDC coils. Isolated channels allow
control of each relay by a different logic system, if necessary. There are two inputs for
each relay coil channel. Modules can ordered with three contact materials, dependent
upon the actual current load. The standard contact material is AgCdO+0.2µmAu.
Contact Configuration:
2N0 + 4N
3N0 + 3NC
4N0 + 2NC
5NO + 1NC
Contact Material*:
AgCdO+0.2µmAu
Part Number
3N0 + 3NC
4N0 + 2NC
Coil Voltage
2N0 + 4NC
5N0 + 1NC
Module Length (mm/in)
1 Chanel
1 Chanel
12V DC
24V DC
156.0A12.1224C
156.0A12.2424C
156.0A12.1233C
156.0A12.2433C
156.0A12.1242C
156.0A12.2442C
156.0A12.1251C
156.0A12.2451C
46.5 (1.85)
46.5 (1.85)
2 Chanel
2 Chanel
12V DC
24V DC
256.0A12.1224C
256.0A12.2424C
256.0A12.1233C
256.0A12.2433C
256.0A12.1242C
256.0A12.2442C
256.0A12.1251C
256.0A12.2451C
91.0 (3.60)
91.0 (3.60)
4 Chanel
4 Chanel
12V DC
24V DC
456.0A12.1224C
456.0A12.2424C
456.0A12.1233C
456.0A12.2433C
456.0A12.1242C
456.0A12.2442C
456.0A12.1251C
456.0A12.2451C
180.0 (7.10)
180.0 (7.10)
* Note: Additional relay contact materials are available upon request. Please contact Altech for additional information.
36
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Safety Relay Modules
6 Pole Relays - 8 Amp, 35 or 32 DIN Rail
6 Pole, 8 Amp
Relay Specifications - 8 Amps
DC Coil Circuits
-Normal Coil Voltage:
-Coil Power Dissipation:
-Max. Switching Voltage:
-Max. Switching Current:
12,24 VDC
0.8-1.0 W
250VDC, 400VAC
8A
-Max. Switching Power
DC
AC
200W
2000VA
-Contact Switching Rate:
-Relay Operate Time
-Relay Release Time
-Contact Arrangements
10 operations/ sec.
20 ms
6 ms
2NO/4NC, 3NO/3NC,
4NO/2NC, 5NO/1NC
-Contact Material:
Standard
Optional
AgSnO2+0.2µmAu
AgNi10+.0.2µmAu
AgNi10+5µmAu
Contact Circuits
-Mechanical Life:
-Ambient Temperature:
-Cover Material:
-Weight:
≥50x106 operation cycles
-40° + 85°C
Thermoplast
38g
Coil Specifications
Top View
of Module
Rated
Voltage
12VDC
24VDC
Voltage
Range
8.4V-16.8V
16.8V-33.6V
Coil
Resistance
145Ω ± 10%
600Ω ± 10%
7 8 9 10 11 12
1 2 3 4 5 6
Relay Configurations
2N0 + 4NC
NO Pin (1,2), (7,8)
NC Pin (3,4), (5,6), (9,10), (11,12)
3N0 + 3NC
NO Pin (1,2), (7,8), (9,10)
NC Pin (3,4), (5,6), (11,12)
4N0 + 2NC
NO Pin (1,2), (3,4), (7,8), (9,10)
NC Pin (5,6), (11,12)
5N0 + 1NC
NO Pin (1,2), (3,4), (5,6), ((7,8), (9,10)
NC Pin (11,12)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
37
InterfaceMods2013(Modified).QXD_Interface2005(new)1.QXD 11/14/13 12:27 PM Page 38
Safety Relay Modules
6 Pole Relays - 10 Amp, 35 or 32 DIN Rail
6 Pole, 10 Amp
TS35x7.5 84.2mm (3.31 in.)
TS32x15 89.2mm (3.51 in.)
L
Altech Safety Relay Modules utilize Relays with Force-Guided-Contacts that meet or
exceed international standards, TÜV, SA, SUVA, and UL. They are designed to protect
man and machine as specified in OSHA CFR1910 Regulations, which is a mandatory
requirement of the European Machinery Directive EMD 89.392 EEC.
• Screw-Cage clamp Connections
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression With DC Coil
• Din Rail Mount, Panel Mount Available
m
m )
0 in.
12 .72
(4
Altech Safety Relays are electro-mechanical relays that are mechanically linked
together, causing all contacts to move together when the coil is energized. ForceGuided-contacts are also known as positive-guided-contacts, captive contacts or
locked contacts. In addition, our Safety Relays have Crown Contacts which provides
two locations per contacts to improve switching conditions. The Safety Relays are
used in Safety Devices such as Emergency Stop Modules, Safety Gate Monitors, 2Hand Safety Modules, Safety Light Curtains, etc.
This series of Safety Relay Modules consist of 6 pole relays with three configuration
choices (2NO+4NC, 3NO+3NC, 4NO+2NC), 8 or 10 Amp contacts and either 1, 2 and
4 isolated channels with 12 or 24 VDC coils. Isolated channels allow control of each
relay by a different logic system, if necessary. There are two inputs for each relay coil
channel. Modules can ordered with three contact materials, dependent upon the
actual current load. The standard contact material is AgCd0+0.2µmAu.
Contact Material*:
AgCdO+0.2µmAu
Contact Ratings:
10A 250VDC,400VAC
2N.0 + 4N.C
1 Channel
1 Channel
2 Channel
2 Channel
4 Channel
4 Channel
Coil Voltage
12V
24V
12V
24V
12V
24V
Part Number
156.0A02.1224C
156.0A02.2424C
256.0A02.1224C
256.0A02.2424C
456.0A02.1224C
456.0A02.2424C
Contacts:
3N.0 + 3N.C
4N.0 + 2N.C
156.0A02.1233C
156.0A02.2433C
256.0A02.1233C
256.0A02.2433C
456.0A02.1233C
456.0A02.2433C
Part Number
156.0A02.1242C
156.0A02.2442C
256.0A02.1242C
256.0A02.2442C
456.0A02.1242C
456.0A02.2442C
Module Length (L)
in mm (in)"
46.45 (1.83)
46.45 (1.83)
90.90 (3.58)
90.90 (3.58)
179.80 (7.08)
179.80 (7.08)
* Note: Additional relay contact materials are available upon request. Please contact Altech for additional information.
38
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Safety Relay Modules
6 Pole Relays - 10 Amp, 35 or 32 DIN Rail
6 Pole, 10 Amp
Relay Specifications - 10 Amps
DC Coil Circuits
-Normal Coil Voltage:
-Coil Power Dissipation:
-Max. Switching Voltage:
-Max. Switching Current:
12,24 VDC
1.0 W
250VDC, 400VAC
10A
-Max. Switching Power
DC
AC
-Contact Switching Rate:
-Relay Operate Time
-Relay Release Time
-Contact Arrangements
240W
2500VA
10 operations/ sec.
27 ms
5 ms
2NO/4NC, 3NO/3NC, 4NO/2NC
-Contact Material:
Standard
Optional
Contact Circuits
AgSnO2+0.2µmAu
AgNi10+0.2µmAu
AgNi10+5µmAu
-Mechanical Life:
-Ambient Temperature:
-Cover Material:
-Weight:
≥30x106 operation cycles
-40°+ 80°C
Thermoplast
85g
Coil Specifications
Top View
of Module
Rated
Voltage
12VDC
24VDC
Voltage
Range
8.4V-19.2V
16.8V-38.4V
Coil
Resistance
140Ω ± 10%
570Ω ± 10%
7 8 9 10 11 12
1 2 3 4 5 6
Relay Configurations
2N.0 + 4N.C
NO Pin (5,6), (11,12)
NC Pin (1,2), (3,4), (7,8), (9,10)
3N.0 + 3N.C
NO Pin (3,4), (5,6), (11,12)
NC Pin (1,2), (7,8), (9,10)
4N.0 + 2N.C
NO Pin (3,4), (5,6), (9,10), (11,12)
NC Pin (1,2), (7,8)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
39
Safety Relay Modules
8 Pole - 10 Amp, 35 or 32 DIN Rail
8 Pole, 10 Amp
TS35x7.5 69mm (2.72 in.)
TS32x15 74mm (2.91 in.)
These Safety Relay Modules utilize Relays with Force-Guided-Contacts that meet or
exceed international standards, TÜV, SA, SUVA, and UL. They meet the standard
EN50205 for safety relays, UL/94/VO fire protection, VDE 0106 Protection Class 11,
and VDE 0110/group C 250VAC insulation class.
• Screw-Cage clamp Connections
• LED Coil Voltage Indicator
• Reverse DC Polarity LED Protection
• Surge Suppression With DC Coil
• Din Rail Mount, Panel Mount Available
L
m
m n.)
87 4 3 i
(3 .
Altech Safety Relays are electro-mechanical relays that are mechanically linked
together, causing all contacts to move together when the coil is energized. ForceGuided-contacts are also known as positive-guided-contacts, captive contacts or
locked contacts. In addition, our Safety Relays have Crown Contacts which provides
two locations per contacts to improve switching conditions. The Safety Relays are
used in Safety Devices such as Emergency Stop Modules, Safety Gate Monitors, 2Hand Safety Modules, Safety Light Curtains, etc.
This series of Safety Relay Modules consists of 8 pole relays with 10 Amps in six
configurations choices. Standard contact material for this series is AgSnO2 + 0.2µmAu.
Contact Material*:
AgCdO+0.2µmAu
Contact Ratings:
10A 250VDC,400VAC
Contacts:
6 NO/2 NC
5 NO/3 NC
Part Number
156.OA03.1271C
156.OA03.2471C
156.OA03.1262C
156.OA03.2462C
Part Number
156.OA03.1253C
156.OA03.2453C
4 NO/4 NC
Contacts:
3 NO/5 NC
2 NO/6 NC
156.OA03.1235C
156.OA03.2435C
Part Number
156.OA03.1226C
156.OA03.2426C
7 NO/1 NC
1 Channel
1 Channel
1 Channel
1 Channel
40
Coil Voltage
12
24
Coil Voltage
12
24
Part Number
156.OA03.1244C
156.OA03.2444C
Module Length (L)
in mm (in)"
103.6 (4.08)
103.6 (4.08)
Module Length (L)
in mm (in)"
103.6 (4.08)
103.6 (4.08)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Safety Relay Modules
8 Pole - 10 Amp, 35 or 32 DIN Rail
8 Pole, 10 Amp
Relay Specifications - 8 Pole
DC Coil Circuits
-Normal Coil Voltage:
-Coil Power Dissipation:
-Max. Switching Voltage:
-Max. Switching Current:
12, 24 VDC
1.25-1.65W
250VDC
10A
-Max. Switching Power:
-Contact Switching Rate:
-Relay Operate Time
-Relay Release Time
-Contact Arrangements:
2500VAC
10 operations per second
27 ms
5 ms
2NO/16NC
3NO/5NC
4NO/4NC
5NO/3NC
6NO/2NC
7NO/1NC
Contact Circuits
AgSnO2+0.2µmAu
-Contact Material:
-Mechanical Life:
-Ambient Temperature:
-Weight:
30x106 operation cycles
-25° + 75°C
95g
Top View
of Module
Coil Specifications
9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
Rated
Voltage
12VDC
24VDC
Min.
Pick-up
8.4V-15.2V
16.8V-38.4V
Coil
Resistance
88Ω/112Ω ± 15%*
370Ω/460Ω ± 15%*
Relay Configurations
* 88Ω/370Ω for contact arrangements
2NO/6NC, 3NO/5NC
2NO/6NC
NO Pin (7,8), (15,16)
NC Pin (1,2), (3,4), (5,6), (9,10), (11,12), (13,14)
* 112Ω/460Ω for contact arrangements
4NO/4NC, 5NO/3NC/6NO/2NC/7NO/7NC
3NO/5NC
NO Pin (5,6), (7,8), (15,16)
NC Pin (1,2), (3,4), (9,10), (11,12), (13,14)
4NO /4NC
NO Pin (5,6), (7,8), (13,14), (15,16)
NC Pin (1,2), (3,4), (9,10), (11,12), (13,14)
5NO /3NC
NO Pin (3,4), (5,6), (7,8), (13,14), (15,16)
NC Pin (1,2), (9,10), (11,12)
6NO /2NC
NO Pin (3,4), (5,6), (7,8), (11,12), (13,14), (15,16)
NC Pin (1,2), (9,10)
7NO /1NC
NO Pi (1,2), (3,4), (5,6), (7,8), (9,10), (11,12), (13,14), (15,16)
NC Pin (9,10)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
41
Interfaces
Isolated I/O Opto Carrier, 35 or 32 DIN Rail
I/O Isolated
Mount standard opto coupler input/output (I/O) modules in a high density arrangement for logic output to field devices, or for input of field data to the controller. I/O
modules optically isolate ICs and PLCs from damaging field voltage spikes and line
noise, while controlling up to 3 Amp field current with less than 20mA logic current.
Altech I/O Module Carriers can accept up to 16 industry standard 0.6 in. (15.24mm)
I/O modules in any combination: Input, Output, AC or DC from most manufacturers.
TS35x7.5 37mm (1.46 in.)†
TS32x15 42mm (1.65 in.)†
L
• Screw-Cage Clamp Connection
• Integral Sockets, Retaining Nut
a
m .)
m in
7
8 .43
(3
• Field Voltage Rating: 280V AC/DC
• LED Indication, Fuse Protection
• DIN Rail Mount, Panel Mount Available
Custom designs can be accommodated!
Low current LED with dropping resistor for high resistance
pull-up and low logic sink/source current requirements.
Technical Information
Fuse Rating...........5A/125C ACb
Wire Range ...........0.5-4 mm2 / 22-12 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
Type
Position
Logic Voltage
LED
Module Length (L)
in mm (in)
8954.0/B
I/O I-1B
1 Position
5V DC
Green
34.5 (1.36)
8954.0/E
I/O I-1E
1 Position
15V DC
Yellow
34.5 (1.36)
8954.0/G
I/O I-1G
1 Position
24V DC
Red
34.5 (1.36)
8955.0/B
I/O I-2B
2 Position
5V DC
Green
57.8 (2.28)
8955.0/E
I/O I-2E
2 Position
15V DC
Yellow
57.8 (2.28)
8955.0/G
I/O I-2G
2 Position
24V DC
Red
57.8 (2.28)
8956.0/B
I/O I-4B
4 Position
5V DC
Green
114 (4.49)
8956.0/E
I/O I-4E
4 Position
15V DC
Yellow
114 (4.49)
8956.0/G
I/O I-4G
4 Position
24V DC
Red
114 (4.49)
8957.0/B
I/O I-8B
8 Position
5V DC
Green
226 (8.90)
8957.0/E
I/O I-8E
8 Position
15V DC
Yellow
226 (8.90)
8957.0/G
I/O I-8G
8 Position
24V DC
Red
226 (8.90)
Part Number
a
Fuse rating limits field side rating.
- PCB Traces, Field Side: 10A/300V
- PCB Traces, Logic Side: 1A with 6A Bus
- Terminal Blocks: 15A/300V
42
†
Dimension is to top board, add height of relay
to determine clearance.
b
3A/250V fuse available, please consult Altech.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interfaces
Isolated I/O Opto Carrier, 35 or 32 DIN Rail
Standard Pinout
Standard Pinout
The I/O Module pin utilization information listed below is intended for use only as a
guide. For specific applications, please use only the module manufacturer’s published
specifications.
Pins 1 & 2: Field Connections
- AC Output to field load, inductive up to 3.5A at nominal 24V AC, 120V AC or
240V AC. AC hot to either pin, field load on other pin.
- DC Output to field load (inductive OK with commutating diode). Some modules
polarized with pin #1 positive (+). Standard output voltages 60V DC (5-60), 200V
DC (10-200).
- AC Input of field data to the logic, 10mA max at nominal 24V AC (18-36), 120V
AC (90-140) and 240V AC (90-280). Field signal to either pin.
- DC Input of field data to the logic, some modules dual rated AC/DC, other nominal
5-28V DC (min. 4, max. 32), and nominal 12-48V DC (min. 10, max. 60). Some
modules polarized with pin #1 (+).
Pin 3: VCC Logic Power
- Standard modules are available in three nominal logic voltages: 5V DC (normally
min. 3 to max. 6), 15V DC (12 to 18) and 24V DC (20 to 30).
Pin 4: Logic Signal
- Output - Logic ground (sink) on pin #4 closes output circuit (pin #1 to pin #2
normally open, shorts with sink on input pin #4). A few positive-logic modules are
available.
- Input - Field signal to pins #1 and #2 gives 20-25mA sink at pin #4 (to pin #5).
Pin 5: Logic Ground
I/O Isolated Positions
- On input modules only (no pin #5 on output modules).
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
43
Interfaces
Bussed I/O Opto Carrier, 35 or 32 DIN Rail
I/O Bussed
TS35x7.5 37mm (1.46 in.)†
TS32x15 42mm (1.65 in.)†
Mount standard opto coupler input/output (I/O) modules in a high density arrangement for logic output to field devices, or for input of field data to the controller. I/O
modules optically isolate ICs and PLCs from damaging field voltage spikes and line
noise, while controlling up to 3 Amp field current with less than 20mA logic current.
Altech I/O Module Carriers can accept up to 16 industry standard 0.6 in. (15.24mm)
I/O modules in any combination: Input, Output, AC or DC from most manufacturers.
L
• Screw-Cage Clamp Connection
• Integral Sockets, Retaining Nut
a
• Field Voltage Rating: 280V AC/DC
• LED Indication, Fuse Protection
• DIN Rail Mount, Panel Mount Available
m
m in.)
87 43
.
(3
Custom designs can be accommodated!
Logic status LED which uses the I/O module impedance as its dropping resistor.
Technical Information
Fuse Rating...........5A/125C ACb
Wire Range ...........0.5-4 mm2 / 22-12 AWG
Torque ...................0.5-4 Nm / 4 lbs-in.
Stripping Length ...8 mm
Type
Position
Logic Voltage
LED
Module Length (L)
in mm (in)
8956.0
I/O B-4
4 Position
5 to 24V DC
Green
114 (4.49)
8959.0
I/O B-8
8 Position
5 to 24V DC
Green
183 (7.20)
8861.0
I/O B-16
16 Position
5 to 24V DC
Green
363 (14.30)
Part Number
a
Fuse rating limits field side rating.
- PCB Traces, Field Side: 10A/300V
- PCB Traces, Logic Side: 1A with 6A Bus
- Terminal Blocks: 15A/300V
44
†
Dimension is to top board, add height of relay
to determine clearance.
b
3A/250V fuse available, please consult Altech.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Interfaces
Bussed I/O Opto Carrier, 35 or 32 DIN Rail
Standard Pinout
Standard Pinout
The I/O Module pin utilization information listed below is intended for use only as a
guide. For specific applications, please use only the module manufacturer’s published
specifications.
Pins 1 & 2: Field Connections
- AC Output to field load, inductive up to 3.5A at nominal 24V AC, 120V AC or
240V AC. AC hot to either pin, field load on other pin.
- DC Output to field load (inductive OK with commutating diode). Some modules
polarized with pin #1 positive (+). Standard output voltages 60V DC (5-60), 200V
DC (10-200).
- AC Input of field data to the logic, 10mA max at nominal 24V AC (18-36), 120V
AC (90-140) and 240V AC (90-280). Field signal to either pin.
- DC Input of field data to the logic, some modules dual rated AC/DC, other nominal
5-28V DC (min. 4, max. 32), and nominal 12-48V DC (min. 10, max. 60). Some
modules polarized with pin #1 (+).
Pin 3: VCC Logic Power
- Standard modules are available in three nominal logic voltages: 5V DC (normally
min. 3 to max. 6), 15V DC (12 to 18) and 24V DC (20 to 30).
Pin 4: Logic Signal
I/O Bussed Positions
- Output - Logic ground (sink) on pin #4 closes output circuit (pin #1 to pin #2
normally open, shorts with sink on input pin #4). A few positive-logic modules are
available.
- Input - Field signal to pins #1 and #2 gives 20-25mA sink at pin #4 (to pin #5).
Pin 5: Logic Ground
- On input modules only (no pin #5 on output modules).
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
45
PCB Mounting Tracks
Narrow & Wide Mounting Track Extrusion and Components
Mount standard or custom printed circuit
boards in Mounting Tracks which can be
conveniently DIN rail or panel mounted in
your control panel or cabinet. These are the
same tracks used for Altech interface
modules. We now make them available to
you to house and protect your custom
boards, etc. Tracks are easily cut to size or
can be ordered precut to specific lengths.
They are easily assembled from standard
components and snap onto 35mm DIN rail or
can be panel mounted.
For PC Board Widths 73mm (2.9 in.)
W
MTGTK1
EPS
L
EPDR1
Each track has two sets of printed circuit
board guides to accept two alternate board
widths.
End Sections hold printed circuit boards
securely in place and keep out foreign
objects.
DIN Rail
Mount
MTGF1
Panel
Mount
Part Number
MOUNTING
When mounting extrusions on DIN rail,
order two or more DIN Rail mounting feet.
These feet slide into grooves on the
extrusion. Then attach two DIN Rail Mount
End Sections with help of EPS screws.
To panel mount, order two Panel Mount End
Sections (and EPS screws), each with an
integral mounting flange with a 6 x 8mm (.24
x .32 in.) hole slot.
If desired, tracks can be direct mounted
using double sided tape. Order two DIN rail
mount end sections (and EPS screws).
• Standard Lengths: 1m (3'-3") or 2m (6'-6")
• Track Material: PVC, V0 grade**
• Temperature Limit:
Short Term - 80°C (176°F)
Continuous - 70°C (158°F)
• End Section, Foot Material: Polyamide
• Preassembled, Precut Lengths Available
• Tracks Accept Standard MT2 Marking Tags
Mounting Track
1 meter, grey
2 meter, grey
1 meter, green*
2 meter, green*
MTGTK1/1M
MTGTK1
MTGTK1/1M/G
MTGTK1/G
DIN Rail Mount End Section, grey
DIN Rail Mount End Section, green*
EPDR1
EPDR1/G
100
100
DIN Rail Mounting Foot, grey
DIN Rail Mounting Foot, green*
MTGF1
MTGF1/G
100
100
Panel Mount End Section, grey
Panel Mount End Section, green*
EPDP1
EPDP1/G
100
100
DIN Rail / Panel Mount End Section
Screws #4x1/2”, Phillips Pan head
(2 required per end section)
EPS
200
Marking Tags
MT2
100
Narrow Mounting Track
73
MTGTK1
11.4
High Guide (HG)
73 ± 1mm (2.9 ± 0.05 in.)
84
PCB MOUNTING TRACK (73 mm)
15
Mounting Track Extrusion
"Cut-to-Size" Formula
Extrusion Length = Printed Circuit
Board Length – 4.5mm (.175 in.)
2
69
16
Track Type
5
5
5
5
Accessories
Sizing Information
Printed Circuit Board Width
Std. Pk.
15
35
82
* Green color available on request.
** UL File No. E306932 (ER 635, EH 660)
46
DIN RAIL MOUNTING FOOT (73mm)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
PCB Mounting Tracks
Narrow & Wide Mounting Track Extrusion and Components
For PC Board Widths 110mm (4.9 in.)
Panel Mount Details
MTGTK2
MTGTK2
W
L
MTGF2
EPDR2
EPDP2
EPS
DIN Rail
Mount
Panel
Mount
Part Number
Mounting Track
1 meter, grey
2 meter, grey
1 meter, green*
2 meter, green*
Std. Pk.
MTGTK2/1M
MTGTK2
MTGTK2/1M/G
MTGTK2/G
5
5
5
5
Accessories
DIN Rail Mount End Section, grey
DIN Rail Mount End Section, green*
EPDR2
EPDR2/G
100
100
DIN Rail Mounting Foot, grey
DIN Rail Mounting Foot, green*
MTGF2
MTGF2/G
100
100
Panel Mount End Section, grey
Panel Mount End Section, green*
EPDP2
EPDP2/G
100
100
DIN Rail / Panel Mount End Section
Screws #4x1/2”, Phillips Pan head
(2 required per end section)
EPS
200
Marking Tags
MT2
100
Wide Mounting Track
110
Sizing Information
11.4
16
2
Printed Circuit Board Width
119
PCB MOUNTING TRACK (110 mm)
Track Type
MTGTK2
High Guide (HG)
110 ± 1mm (4.3 ± 0.05 in.)
15
Mounting Track Extrusion
"Cut-to-Size" Formula
15
35
117
Extrusion Length = Printed Circuit
Board Length – 4.5mm (.175 in.)
DIN RAIL MOUNTING FOOT (110mm)
aAlso applies for DIN Rail Mount Unit
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
47
CUSTOM INTERFACE MODULES
If your design or application requires more functionality or
features than our standard product, Altech offers complete
engineering, prototype and production services for custom
modules.
Our staff has the ability to take your design or requirements and
manufacture your custom module. Custom module production
generally includes engineering, PCB layout and prototypes,
packaged in Altech extrusions for mounting on panels
or DIN Rail. In many industrial control systems,
customized designs are the solution for many
problems.
Altech provides a quick turnaround and competitive
solution to your problem. Altech provides the
following benefits to your company:
Application Assistance
Modify a standard product
Help define a new product
Engineering Capability
Use of latest CAD system
PCB layouts completed promptly
Prototypes available two weeks
after PCB layout approval
Manufacturing Capability
Complete in-house manufacturing
ISO 9001 Certified
Minimum Quantities
25 piece minimum for custom quotes
Quotation provided at no cost
Altech Benefits
Fast turnaround due to in-house capability
Highly competitive in-house manufacturing
Use of Altech components (blocks,
extrusions, connectors)
116
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
CUSTOM ASSEMBLIES AVAILABLE
•
•
•
•
•
Most competitive in industry
Made to your specifications
Large inventory of components
Variety of colors available
Shipped in 3-4 weeks
• DIN Rail Terminal Block
Assemblies
• Push Button Control Stations
• Relay Assemblies
• Custom Interface Assemblies
• Enclosure Customization
• Imprinting
• Foot Switch Customization
• New Product Development
• Other Value Added Services.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
117
INDEX
Part No.
5492.2
5492.5
5494.2
5494.5
5502.2
5502.5
5506.2
5506.5
5508.2
5508.5
5514.2
5514.3
5514.5
5514.6
5700.2
5701.2
5702.2
5702.3
5702.4
5703.2
5703.3
5703.4
5704.2
5704.3
5704.4
5705.2
5705.3
5705.4
5706.2
5706.3
5706.4
5707.2
5707.3
5707.4
5718.2
5718.3
5719.2
5719.3
5720.2
5721.2
5722.2
5723.2
5724.2
5725.2
5726.2
5727.2
5728.2
5729.2
5740.2
5741.2
5742.2
5743.2
5744.2
5745.2
5746.2
5747.2
5748.2
5749.2
5800.2
5800.3
5801.2
5801.3
5802.2
5802.3
5803.2
5803.3
5804.2
5804.3
5805.2
5805.3
5806.2
5806.3
8835.2
8836.2
Pg.
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .13
. . . . . . . . . . . . . . . . . . . . . .13
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .15
. . . . . . . . . . . . . . . . . . . . . .15
. . . . . . . . . . . . . . . . . . . . . .15
. . . . . . . . . . . . . . . . . . . . . .15
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . . . . . . . .8
. . . . . . . . . . . . . . . . . . . . . . .8
. . . . . . . . . . . . . . . . . . . . . . .8
. . . . . . . . . . . . . . . . . . . . . . .8
. . . . . . . . . . . . . . . . . . . . . . .8
. . . . . . . . . . . . . . . . . . . . . . .9
. . . . . . . . . . . . . . . . . . . . . . .9
. . . . . . . . . . . . . . . . . . . . . . .9
. . . . . . . . . . . . . . . . . . . . . . .9
. . . . . . . . . . . . . . . . . . . . . . .9
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .12
. . . . . . . . . . . . . . . . . . . . . .12
Part No.
8837.2
8838.2
8839.2
8840.2
8842.2
8842.3
8842.4
8850.2
8850.3
8850.4
8861.0
8905.2
8905.3
8906.2
8906.3
8907.2
8907.3
8908.2
8908.3
8909.2
8909.3
8910.2
8910.3
8911.2
8911.3
8912.2
8912.3
8912.5
8912.6
8913.3
8913.6
8914.2
8914.5
8921.2
8921.5
8923.2
8923.3
8923.5
8923.6
8924.2
8924.4
8924.5
8924.6
8925.2
8925.3
8925.5
8925.6
8926.2
8926.3
8926.5
8926.6
8927.2
8927.3
8927.5
8927.6
8928.2
8928.3
8928.5
8928.6
8929.2
8929.3
8929.5
8929.6
8931.2
8931.3
8931.5
8931.6
8932.2
8932.5
8933.2
8933.3
8933.5
8933.6
8935.2
Pg.
. . . . . . . . . . . . . . . . . . . . . .12
. . . . . . . . . . . . . . . . . . . . . .12
. . . . . . . . . . . . . . . . . . . . . .12
. . . . . . . . . . . . . . . . . . . . . .12
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .44
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .24
. . . . . . . . . . . . . . . . . . . . . .26
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .20
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
Part No.
8935.3
8935.5
8935.6
8938.2
8939.2
8940.2
8940.3
8940.5
8940.6
8941.2
8941.3
8941.5
8941.6
8942.2
8942.3
8942.5
8942.6
8943.2
8943.3
8943.5
8943.6
8944.2
8944.5
8945.2
8945.5
8946.2
8946.5
8948.2
8948.5
8949.3
8949.6
8951.2
8951.3
8951.5
8951.6
8953.2
8953.3
8953.5
8953.6
8954.2
8954.3
8954.5
8954.6
8955.2
8955.3
8955.5
8955.6
8956.2
8956.3
8956.5
8956.6
8957.2
8957.3
8957.5
8957.6
8959.0
8959.2
8959.3
8959.5
8959.6
8963.2
8963.5
8972.2
8972.5
8973.2
8973.3
8973.4
8974.2
8974.3
8974.4
8975.2
8975.3
8975.4
8995.2
Pg.
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .14
. . . . . . . . . . . . . . . . . . . . . .14
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .16
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .44
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .18
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . . . . .18
Part No.
BOLD - Regular stocked items.
118
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Pg.
8995.5 . . . . . . . . . . . . . . . . . . . . . .18
8999.2 . . . . . . . . . . . . . . . . . . . . . .18
8999.5 . . . . . . . . . . . . . . . . . . . . . .18
125 (4.92) . . . . . . . . . . . . . . . . . . . .30
125 (4.92) . . . . . . . . . . . . . . . . . . . .30
125 (4.92) . . . . . . . . . . . . . . . . . . . .30
125 (4.92) . . . . . . . . . . . . . . . . . . . .30
156.0A01.1222C . . . . . . . . . . . . . .34
156.0A01.1231C . . . . . . . . . . . . . .34
156.0A01.2422C . . . . . . . . . . . . . .34
156.0A01.2431C . . . . . . . . . . . . . .34
156.0A11.1222C . . . . . . . . . . . . . .32
156.0A11.1231C . . . . . . . . . . . . . .32
156.0A11.2422C . . . . . . . . . . . . . .32
156.0A11.2431C . . . . . . . . . . . . . .32
156.0A12.1224C . . . . . . . . . . . . . .36
156.0A12.1224C . . . . . . . . . . . . . .38
156.0A12.1233C . . . . . . . . . . . . . .36
156.0A12.1233C . . . . . . . . . . . . . .38
156.0A12.1242C . . . . . . . . . . . . . .36
156.0A12.1242C . . . . . . . . . . . . . .38
156.0A12.2424C . . . . . . . . . . . . . .36
156.0A12.2424C . . . . . . . . . . . . . .38
156.0A12.2433C . . . . . . . . . . . . . .36
156.0A12.2433C . . . . . . . . . . . . . .38
156.0A12.2442C . . . . . . . . . . . . . .36
156.0A12.2442C . . . . . . . . . . . . . .38
156.OA03.1226C . . . . . . . . . . . . . .40
156.OA03.1235C . . . . . . . . . . . . . .40
156.OA03.1244C . . . . . . . . . . . . . .40
156.OA03.1253C . . . . . . . . . . . . . .40
156.OA03.1262C . . . . . . . . . . . . . .40
156.OA03.1271C . . . . . . . . . . . . . .40
156.OA03.2426C . . . . . . . . . . . . . .40
156.OA03.2435C . . . . . . . . . . . . . .40
156.OA03.2444C . . . . . . . . . . . . . .40
156.OA03.2453C . . . . . . . . . . . . . .40
156.OA03.2462C . . . . . . . . . . . . . .40
156.OA03.2471C . . . . . . . . . . . . . .40
248 (9.76) . . . . . . . . . . . . . . . . . . . .30
248 (9.76) . . . . . . . . . . . . . . . . . . . .30
248 (9.76) . . . . . . . . . . . . . . . . . . . .30
248 (9.76) . . . . . . . . . . . . . . . . . . . .30
256.0A01.1222C . . . . . . . . . . . . . .34
256.0A01.1231C . . . . . . . . . . . . . .34
256.0A01.2422C . . . . . . . . . . . . . .34
256.0A01.2431C . . . . . . . . . . . . . .34
256.0A11.1222C . . . . . . . . . . . . . .32
256.0A11.1231C . . . . . . . . . . . . . .32
256.0A11.2422C . . . . . . . . . . . . . .32
256.0A11.2431C . . . . . . . . . . . . . .32
256.0A12.1224C . . . . . . . . . . . . . .36
256.0A12.1224C . . . . . . . . . . . . . .38
256.0A12.1233C . . . . . . . . . . . . . .36
256.0A12.1233C . . . . . . . . . . . . . .38
256.0A12.1242C . . . . . . . . . . . . . .36
256.0A12.1242C . . . . . . . . . . . . . .38
256.0A12.2424C . . . . . . . . . . . . . .36
256.0A12.2424C . . . . . . . . . . . . . .38
256.0A12.2433C . . . . . . . . . . . . . .36
256.0A12.2433C . . . . . . . . . . . . . .38
256.0A12.2442C . . . . . . . . . . . . . .36
256.0A12.2442C . . . . . . . . . . . . . .38
456.0A01.1222C . . . . . . . . . . . . . .34
456.0A01.1231C . . . . . . . . . . . . . .34
456.0A01.2422C . . . . . . . . . . . . . .34
456.0A01.2431C . . . . . . . . . . . . . .34
456.0A11.1222C . . . . . . . . . . . . . .32
456.0A11.1231C . . . . . . . . . . . . . .32
456.0A11.2422C . . . . . . . . . . . . . .32
456.0A11.2431C . . . . . . . . . . . . . .32
456.0A12.1224C . . . . . . . . . . . . . .36
456.0A12.1224C . . . . . . . . . . . . . .38
456.0A12.1233C . . . . . . . . . . . . . .36
INDEX
Part No.
Pg.
456.0A12.1233C . . . . . . . . . . . . . .38
456.0A12.1242C . . . . . . . . . . . . . .36
456.0A12.1242C . . . . . . . . . . . . . .38
456.0A12.2424C . . . . . . . . . . . . . .36
456.0A12.2424C . . . . . . . . . . . . . .38
456.0A12.2433C . . . . . . . . . . . . . .36
456.0A12.2433C . . . . . . . . . . . . . .38
456.0A12.2442C . . . . . . . . . . . . . .36
456.0A12.2442C . . . . . . . . . . . . . .38
5492.2/S . . . . . . . . . . . . . . . . . . . .20
5492.5/S . . . . . . . . . . . . . . . . . . . .20
5494.2/S . . . . . . . . . . . . . . . . . . . .20
5494.5/S . . . . . . . . . . . . . . . . . . . .20
5502.2/S . . . . . . . . . . . . . . . . . . . .20
5502.5/S . . . . . . . . . . . . . . . . . . . .20
5506.2/S . . . . . . . . . . . . . . . . . . . .20
5506.5/S . . . . . . . . . . . . . . . . . . . .20
5508.2/S . . . . . . . . . . . . . . . . . . . .20
5508.5/S . . . . . . . . . . . . . . . . . . . .20
5514.2/S . . . . . . . . . . . . . . . . . . . .20
5514.3/S . . . . . . . . . . . . . . . . . . . .20
5514.5/S . . . . . . . . . . . . . . . . . . . .20
5514.6/S . . . . . . . . . . . . . . . . . . . .20
5700.2/S . . . . . . . . . . . . . . . . . . . .13
5701.2/S . . . . . . . . . . . . . . . . . . . .13
5718.2/S . . . . . . . . . . . . . . . . . . . .15
5718.3/S . . . . . . . . . . . . . . . . . . . .15
5719.2/S . . . . . . . . . . . . . . . . . . . .15
5719.3/S . . . . . . . . . . . . . . . . . . . .15
5720.2/S . . . . . . . . . . . . . . . . . . . . .7
5721.2/S . . . . . . . . . . . . . . . . . . . . .7
5722.2/S . . . . . . . . . . . . . . . . . . . . .7
5723.2/S . . . . . . . . . . . . . . . . . . . . .7
5724.2/S . . . . . . . . . . . . . . . . . . . . .7
5725.2/S . . . . . . . . . . . . . . . . . . . . .7
5726.2/S . . . . . . . . . . . . . . . . . . . . .7
5727.2/S . . . . . . . . . . . . . . . . . . . . .7
5728.2/S . . . . . . . . . . . . . . . . . . . . .7
5729.2/S . . . . . . . . . . . . . . . . . . . . .7
5740.2/S . . . . . . . . . . . . . . . . . . . . .8
5741.2/S . . . . . . . . . . . . . . . . . . . . .8
5742.2/S . . . . . . . . . . . . . . . . . . . . .8
5743.2/S . . . . . . . . . . . . . . . . . . . . .8
5744.2/S . . . . . . . . . . . . . . . . . . . . .8
5745.2/S . . . . . . . . . . . . . . . . . . . . .9
5746.2/S . . . . . . . . . . . . . . . . . . . . .9
5747.2/S . . . . . . . . . . . . . . . . . . . . .9
5748.2/S . . . . . . . . . . . . . . . . . . . . .9
5749.2/S . . . . . . . . . . . . . . . . . . . . .9
5800.2/S . . . . . . . . . . . . . . . . . . . .24
5800.3/S . . . . . . . . . . . . . . . . . . . .26
5801.2/S . . . . . . . . . . . . . . . . . . . .24
5801.3/S . . . . . . . . . . . . . . . . . . . .26
5802.2/S . . . . . . . . . . . . . . . . . . . .24
5802.3/S . . . . . . . . . . . . . . . . . . . .26
5803.2/S . . . . . . . . . . . . . . . . . . . .24
5803.3/S . . . . . . . . . . . . . . . . . . . .26
5804.2/S . . . . . . . . . . . . . . . . . . . .24
5804.3/S . . . . . . . . . . . . . . . . . . . .26
5805.2/S . . . . . . . . . . . . . . . . . . . .24
5805.3/S . . . . . . . . . . . . . . . . . . . .26
5806.2/S . . . . . . . . . . . . . . . . . . . .24
5806.3/S . . . . . . . . . . . . . . . . . . . .26
8835.2/S . . . . . . . . . . . . . . . . . . . .12
8836.2/S . . . . . . . . . . . . . . . . . . . .12
8837.2/S . . . . . . . . . . . . . . . . . . . .12
8838.2/S . . . . . . . . . . . . . . . . . . . .12
8839.2/S . . . . . . . . . . . . . . . . . . . .12
8840.2/S . . . . . . . . . . . . . . . . . . . .12
8905.2/S . . . . . . . . . . . . . . . . . . . .24
8905.3/S . . . . . . . . . . . . . . . . . . . .26
8906.2/S . . . . . . . . . . . . . . . . . . . .24
8906.3/S . . . . . . . . . . . . . . . . . . . .26
8907.2/S . . . . . . . . . . . . . . . . . . . .24
Part No.
Pg.
8907.3/S . . . . . . . . . . . . . . . . . . . .26
8908.2/S . . . . . . . . . . . . . . . . . . . .24
8908.3/S . . . . . . . . . . . . . . . . . . . .26
8909.2/S . . . . . . . . . . . . . . . . . . . .24
8909.3/S . . . . . . . . . . . . . . . . . . . .26
8910.2/S . . . . . . . . . . . . . . . . . . . .24
8910.3/S . . . . . . . . . . . . . . . . . . . .26
8911.2/S . . . . . . . . . . . . . . . . . . . .24
8911.3/S . . . . . . . . . . . . . . . . . . . .26
8912.2/S . . . . . . . . . . . . . . . . . . . .20
8912.3/S . . . . . . . . . . . . . . . . . . . .20
8912.5/S . . . . . . . . . . . . . . . . . . . .20
8912.6/S . . . . . . . . . . . . . . . . . . . .20
8913.3/S . . . . . . . . . . . . . . . . . . . .20
8913.6/S . . . . . . . . . . . . . . . . . . . .20
8914.2/S . . . . . . . . . . . . . . . . . . . .20
8914.5/S . . . . . . . . . . . . . . . . . . . .20
8921.2/S . . . . . . . . . . . . . . . . . . . .20
8921.5/S . . . . . . . . . . . . . . . . . . . .20
8923.2/S . . . . . . . . . . . . . . . . . . . .22
8923.2C . . . . . . . . . . . . . . . . . . . . .30
8923.2N . . . . . . . . . . . . . . . . . . . . .30
8923.2S . . . . . . . . . . . . . . . . . . . . .30
8923.3/S . . . . . . . . . . . . . . . . . . . .22
8923.3C . . . . . . . . . . . . . . . . . . . . .30
8923.3N . . . . . . . . . . . . . . . . . . . . .30
8923.3S . . . . . . . . . . . . . . . . . . . . .30
8923.5/S . . . . . . . . . . . . . . . . . . . .22
8923.6/S . . . . . . . . . . . . . . . . . . . .22
8924.2/S . . . . . . . . . . . . . . . . . . . .22
8924.2C . . . . . . . . . . . . . . . . . . . . .30
8924.2N . . . . . . . . . . . . . . . . . . . . .30
8924.2S . . . . . . . . . . . . . . . . . . . . .30
8924.4/S . . . . . . . . . . . . . . . . . . . .22
8924.4C . . . . . . . . . . . . . . . . . . . . .30
8924.4N . . . . . . . . . . . . . . . . . . . . .30
8924.4S . . . . . . . . . . . . . . . . . . . . .30
8924.5/S . . . . . . . . . . . . . . . . . . . .22
8924.6/S . . . . . . . . . . . . . . . . . . . .22
8925.2/S . . . . . . . . . . . . . . . . . . . .22
8925.3/S . . . . . . . . . . . . . . . . . . . .22
8925.5/S . . . . . . . . . . . . . . . . . . . .22
8925.6/S . . . . . . . . . . . . . . . . . . . .22
8926.2/S . . . . . . . . . . . . . . . . . . . .22
8926.2C . . . . . . . . . . . . . . . . . . . . .30
8926.2N . . . . . . . . . . . . . . . . . . . . .30
8926.2S . . . . . . . . . . . . . . . . . . . . .30
8926.3/S . . . . . . . . . . . . . . . . . . . .22
8926.3C . . . . . . . . . . . . . . . . . . . . .30
8926.3N . . . . . . . . . . . . . . . . . . . . .30
8926.3S . . . . . . . . . . . . . . . . . . . . .30
8926.5/S . . . . . . . . . . . . . . . . . . . .22
8926.6/S . . . . . . . . . . . . . . . . . . . .22
8927.2/S . . . . . . . . . . . . . . . . . . . .22
8927.2C . . . . . . . . . . . . . . . . . . . . .30
8927.2N . . . . . . . . . . . . . . . . . . . . .30
8927.2S . . . . . . . . . . . . . . . . . . . . .30
8927.3/S . . . . . . . . . . . . . . . . . . . .22
8927.3C . . . . . . . . . . . . . . . . . . . . .30
8927.3N . . . . . . . . . . . . . . . . . . . . .30
8927.3S . . . . . . . . . . . . . . . . . . . . .30
8927.5/S . . . . . . . . . . . . . . . . . . . .22
8927.6/S . . . . . . . . . . . . . . . . . . . .22
8928.2/S . . . . . . . . . . . . . . . . . . . .22
8928.3/S . . . . . . . . . . . . . . . . . . . .22
8928.5/S . . . . . . . . . . . . . . . . . . . .22
8928.6/S . . . . . . . . . . . . . . . . . . . .22
8929.2/S . . . . . . . . . . . . . . . . . . . .16
8929.3/S . . . . . . . . . . . . . . . . . . . .16
8929.5/S . . . . . . . . . . . . . . . . . . . .16
8929.6/S . . . . . . . . . . . . . . . . . . . .16
8931.2/S . . . . . . . . . . . . . . . . . . . .16
8931.3/S . . . . . . . . . . . . . . . . . . . .16
8931.5/S . . . . . . . . . . . . . . . . . . . .16
Part No.
Pg.
8931.6/S . . . . . . . . . . . . . . . . . . . .16
8932.2/S . . . . . . . . . . . . . . . . . . . .16
8932.5/S . . . . . . . . . . . . . . . . . . . .16
8933.2/S . . . . . . . . . . . . . . . . . . . .16
8933.3/S . . . . . . . . . . . . . . . . . . . .16
8933.5/S . . . . . . . . . . . . . . . . . . . .16
8933.6/S . . . . . . . . . . . . . . . . . . . .16
8935.2/S . . . . . . . . . . . . . . . . . . . .16
8935.3/S . . . . . . . . . . . . . . . . . . . .16
8935.5/S . . . . . . . . . . . . . . . . . . . .16
8935.6/S . . . . . . . . . . . . . . . . . . . .16
8937.2 . . . . . . . . . . . . . . . . . . . . . .14
8937.2/S . . . . . . . . . . . . . . . . . . . .14
8938.2/S . . . . . . . . . . . . . . . . . . . .14
8939.2/S . . . . . . . . . . . . . . . . . . . .14
8940.2/S . . . . . . . . . . . . . . . . . . . .16
8940.3/S . . . . . . . . . . . . . . . . . . . .16
8940.5/S . . . . . . . . . . . . . . . . . . . .16
8940.6/S . . . . . . . . . . . . . . . . . . . .16
8941.2/S . . . . . . . . . . . . . . . . . . . .16
8941.3/S . . . . . . . . . . . . . . . . . . . .16
8941.5/S . . . . . . . . . . . . . . . . . . . .16
8941.6/S . . . . . . . . . . . . . . . . . . . .16
8942.2/S . . . . . . . . . . . . . . . . . . . .16
8942.3/S . . . . . . . . . . . . . . . . . . . .16
8942.5/S . . . . . . . . . . . . . . . . . . . .16
8942.6/S . . . . . . . . . . . . . . . . . . . .16
8943.2/S . . . . . . . . . . . . . . . . . . . .16
8943.3/S . . . . . . . . . . . . . . . . . . . .16
8943.5/S . . . . . . . . . . . . . . . . . . . .16
8943.6/S . . . . . . . . . . . . . . . . . . . .16
8944.2/S . . . . . . . . . . . . . . . . . . . .16
8944.5/S . . . . . . . . . . . . . . . . . . . .16
8945.2/S . . . . . . . . . . . . . . . . . . . .18
8945.5/S . . . . . . . . . . . . . . . . . . . .18
8946.2/S . . . . . . . . . . . . . . . . . . . .16
8946.5/S . . . . . . . . . . . . . . . . . . . .16
8948.2/S . . . . . . . . . . . . . . . . . . . .16
8948.5/S . . . . . . . . . . . . . . . . . . . .16
8949.2C . . . . . . . . . . . . . . . . . . . . .28
8949.2N . . . . . . . . . . . . . . . . . . . . .28
8949.2S . . . . . . . . . . . . . . . . . . . . .28
8949.3/S . . . . . . . . . . . . . . . . . . . .18
8949.3C . . . . . . . . . . . . . . . . . . . . .28
8949.3N . . . . . . . . . . . . . . . . . . . . .28
8949.3S . . . . . . . . . . . . . . . . . . . . .28
8949.6/S . . . . . . . . . . . . . . . . . . . .18
8951.2/S . . . . . . . . . . . . . . . . . . . .18
8951.2C . . . . . . . . . . . . . . . . . . . . .28
8951.2N . . . . . . . . . . . . . . . . . . . . .28
8951.2S . . . . . . . . . . . . . . . . . . . . .28
8951.3/S . . . . . . . . . . . . . . . . . . . .18
8951.3C . . . . . . . . . . . . . . . . . . . . .28
8951.3N . . . . . . . . . . . . . . . . . . . . .28
8951.3S . . . . . . . . . . . . . . . . . . . . .28
8951.5/S . . . . . . . . . . . . . . . . . . . .18
8951.6/S . . . . . . . . . . . . . . . . . . . .18
8953.2/S . . . . . . . . . . . . . . . . . . . .18
8953.3/S . . . . . . . . . . . . . . . . . . . .18
8953.5/S . . . . . . . . . . . . . . . . . . . .18
8953.6/S . . . . . . . . . . . . . . . . . . . .18
8954.0/B . . . . . . . . . . . . . . . . . . . .42
8954.0/E . . . . . . . . . . . . . . . . . . . .42
8954.0/G . . . . . . . . . . . . . . . . . . . .42
8954.2/S . . . . . . . . . . . . . . . . . . . .18
8954.3/S . . . . . . . . . . . . . . . . . . . .18
8954.5/S . . . . . . . . . . . . . . . . . . . .18
8954.6/S . . . . . . . . . . . . . . . . . . . .18
8955.0/B . . . . . . . . . . . . . . . . . . . .42
8955.0/E . . . . . . . . . . . . . . . . . . . .42
8955.0/G . . . . . . . . . . . . . . . . . . . .42
8955.2/S . . . . . . . . . . . . . . . . . . . .18
8955.2C . . . . . . . . . . . . . . . . . . . . .28
8955.2N . . . . . . . . . . . . . . . . . . . . .28
Part No.
Pg.
8955.2S . . . . . . . . . . . . . . . . . . . . .28
8955.3/S . . . . . . . . . . . . . . . . . . . .18
8955.3C . . . . . . . . . . . . . . . . . . . . .28
8955.3N . . . . . . . . . . . . . . . . . . . . .28
8955.3S . . . . . . . . . . . . . . . . . . . . .28
8955.5/S . . . . . . . . . . . . . . . . . . . .18
8955.6/S . . . . . . . . . . . . . . . . . . . .18
8956.0 . . . . . . . . . . . . . . . . . . . . . .44
8956.0/B . . . . . . . . . . . . . . . . . . . .42
8956.0/E . . . . . . . . . . . . . . . . . . . .42
8956.0/G . . . . . . . . . . . . . . . . . . . .42
8956.2/S . . . . . . . . . . . . . . . . . . . .18
8956.2C . . . . . . . . . . . . . . . . . . . . .28
8956.2N . . . . . . . . . . . . . . . . . . . . .28
8956.2S . . . . . . . . . . . . . . . . . . . . .28
8956.3/S . . . . . . . . . . . . . . . . . . . .18
8956.3C . . . . . . . . . . . . . . . . . . . . .28
8956.3N . . . . . . . . . . . . . . . . . . . . .28
8956.3S . . . . . . . . . . . . . . . . . . . . .28
8956.5/S . . . . . . . . . . . . . . . . . . . .18
8956.6/S . . . . . . . . . . . . . . . . . . . .18
8957.0/B . . . . . . . . . . . . . . . . . . . .42
8957.0/E . . . . . . . . . . . . . . . . . . . .42
8957.0/G . . . . . . . . . . . . . . . . . . . .42
8957.2/S . . . . . . . . . . . . . . . . . . . .18
8957.3/S . . . . . . . . . . . . . . . . . . . .18
8957.5/S . . . . . . . . . . . . . . . . . . . .18
8957.6/S . . . . . . . . . . . . . . . . . . . .18
8959.2/S . . . . . . . . . . . . . . . . . . . .18
8959.3/S . . . . . . . . . . . . . . . . . . . .18
8959.5/S . . . . . . . . . . . . . . . . . . . .18
8959.6/S . . . . . . . . . . . . . . . . . . . .18
8963.2/S . . . . . . . . . . . . . . . . . . . .18
8963.2C . . . . . . . . . . . . . . . . . . . . .28
8963.2N . . . . . . . . . . . . . . . . . . . . .28
8963.2S . . . . . . . . . . . . . . . . . . . . .28
8963.5/S . . . . . . . . . . . . . . . . . . . .18
8971.2 . . . . . . . . . . . . . . . . . . . . . .11
8971.3 . . . . . . . . . . . . . . . . . . . . . .11
8971.4 . . . . . . . . . . . . . . . . . . . . . .11
8972.2/S . . . . . . . . . . . . . . . . . . . .18
8972.2C . . . . . . . . . . . . . . . . . . . . .28
8972.2N . . . . . . . . . . . . . . . . . . . . .28
8972.2S . . . . . . . . . . . . . . . . . . . . .28
8972.5/S . . . . . . . . . . . . . . . . . . . .18
8995.2/S . . . . . . . . . . . . . . . . . . . .18
8995.5/S . . . . . . . . . . . . . . . . . . . .18
8999.2/S . . . . . . . . . . . . . . . . . . . .18
8999.5/S . . . . . . . . . . . . . . . . . . . .18
EPDP1 . . . . . . . . . . . . . . . . . . . . . .46
EPDP1/G . . . . . . . . . . . . . . . . . . . .46
EPDP2 . . . . . . . . . . . . . . . . . . . . . .47
EPDP2/G . . . . . . . . . . . . . . . . . . . .47
EPDR1 . . . . . . . . . . . . . . . . . . . . . .46
EPDR1/G . . . . . . . . . . . . . . . . . . . .46
EPDR2 . . . . . . . . . . . . . . . . . . . . . .47
EPDR2/G . . . . . . . . . . . . . . . . . . . .47
EPS . . . . . . . . . . . . . . . . . . . . . . . .46
EPS . . . . . . . . . . . . . . . . . . . . . . . .47
GD35 . . . . . . . . . . . . . . . . . . . . . . .83
GD50 . . . . . . . . . . . . . . . . . . . . . . .83
GUC11 . . . . . . . . . . . . . . . . . . . . . .65
GZ14U . . . . . . . . . . . . . . . . . . . . . .70
GZ2 . . . . . . . . . . . . . . . . . . . . . . . .65
GZM 80 . . . . . . . . . . . . . . . . . . . .110
GZM 92 . . . . . . . . . . . . . . . . . . . .110
GZM2 . . . . . . . . . . . . . . . . . . . . . . .55
GZM2 . . . . . . . . . . . . . . . . . . . . . .111
GZM3 . . . . . . . . . . . . . . . . . . . . . . .56
GZM3 . . . . . . . . . . . . . . . . . . . . . .111
GZM4 . . . . . . . . . . . . . . . . . . . . . . .56
GZM4 . . . . . . . . . . . . . . . . . . . . . .111
GZM80 . . . . . . . . . . . . . . . . . . . . . .81
GZM92 . . . . . . . . . . . . . . . . . . . . . .82
BOLD - Regular stocked items.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
119
INDEX
Part No.
Pg.
GZMB2 . . . . . . . . . . . . . . . . . . . . .57
GZMB4 . . . . . . . . . . . . . . . . . . . . .57
GZMB80 . . . . . . . . . . . . . . . . . . . .83
GZP11 . . . . . . . . . . . . . . . . . . . . . .69
GZP8 . . . . . . . . . . . . . . . . . . . . . . .69
GZT 80 . . . . . . . . . . . . . . . . . . . . .110
GZT 92 . . . . . . . . . . . . . . . . . . . . .110
GZT2 . . . . . . . . . . . . . . . . . . . . . . .55
GZT2 . . . . . . . . . . . . . . . . . . . . . .111
GZT3 . . . . . . . . . . . . . . . . . . . . . . .55
GZT3 . . . . . . . . . . . . . . . . . . . . . .111
GZT4 . . . . . . . . . . . . . . . . . . . . . . .56
GZT4 . . . . . . . . . . . . . . . . . . . . . .111
GZT80 . . . . . . . . . . . . . . . . . . . . . .81
GZT92 . . . . . . . . . . . . . . . . . . . . . .82
GZY2G . . . . . . . . . . . . . . . . . . . . . .65
M103 . . . . . . . . . . . . . . . . . . . . . .113
M21N . . . . . . . . . . . . . . . . . . . . . .113
M21P . . . . . . . . . . . . . . . . . . . . . .113
M31G* . . . . . . . . . . . . . . . . . . . . .113
M31R . . . . . . . . . . . . . . . . . . . . . .113
M32G . . . . . . . . . . . . . . . . . . . . . .113
M32R . . . . . . . . . . . . . . . . . . . . . .113
M33G . . . . . . . . . . . . . . . . . . . . . .113
M33R . . . . . . . . . . . . . . . . . . . . . .113
M41G . . . . . . . . . . . . . . . . . . . . . .113
M42G . . . . . . . . . . . . . . . . . . . . . .113
M43G . . . . . . . . . . . . . . . . . . . . . .113
M51 . . . . . . . . . . . . . . . . . . . . . . .113
M52 . . . . . . . . . . . . . . . . . . . . . . .113
M53 . . . . . . . . . . . . . . . . . . . . . . .113
M61G* . . . . . . . . . . . . . . . . . . . . .113
M61R . . . . . . . . . . . . . . . . . . . . . .113
M62G . . . . . . . . . . . . . . . . . . . . . .113
M62R . . . . . . . . . . . . . . . . . . . . . .113
M63G* . . . . . . . . . . . . . . . . . . . . .113
M63R . . . . . . . . . . . . . . . . . . . . . .113
M71 . . . . . . . . . . . . . . . . . . . . . . .113
M72 . . . . . . . . . . . . . . . . . . . . . . .113
M73 . . . . . . . . . . . . . . . . . . . . . . .113
M91G . . . . . . . . . . . . . . . . . . . . . .113
M91R . . . . . . . . . . . . . . . . . . . . . .113
M92G . . . . . . . . . . . . . . . . . . . . . .113
M92R . . . . . . . . . . . . . . . . . . . . . .113
M93G . . . . . . . . . . . . . . . . . . . . . .113
M93R . . . . . . . . . . . . . . . . . . . . . .113
MT2 . . . . . . . . . . . . . . . . . . . . . . . .46
MT2 . . . . . . . . . . . . . . . . . . . . . . . .47
MTGF1 . . . . . . . . . . . . . . . . . . . . . .46
MTGF1/G . . . . . . . . . . . . . . . . . . . .46
MTGF2 . . . . . . . . . . . . . . . . . . . . . .47
MTGF2/G . . . . . . . . . . . . . . . . . . . .47
MTGTK1 . . . . . . . . . . . . . . . . . . . .46
MTGTK1/1M . . . . . . . . . . . . . . . . .46
MTGTK1/1M/G . . . . . . . . . . . . . . .46
MTGTK1/G . . . . . . . . . . . . . . . . . .46
MTGTK2 . . . . . . . . . . . . . . . . . . . .47
MTGTK2/1M . . . . . . . . . . . . . . . . .47
MTGTK2/1M/G . . . . . . . . . . . . . . .47
MTGTK2/G . . . . . . . . . . . . . . . . . .47
PI6-1P-115VAC/DC . . . . . . . . . . .91
PI6-1P-12VDC . . . . . . . . . . . . . . . .91
PI6-1P-230VAC/DC . . . . . . . . . . . .91
PI6-1P-24VAC/DC . . . . . . . . . . . .91
PI6-1P-24VDC . . . . . . . . . . . . . . . .91
PI6-1P-36VDC . . . . . . . . . . . . . . . .91
PI6-1P-42VAC/DC . . . . . . . . . . . . .91
PI6-1T-230VAC/DC . . . . . . . . . . . .92
PI6-1T-24VAC/DC . . . . . . . . . . . . .92
PI6-1T-5...32VDC . . . . . . . . . . . . .92
PI6-OC-230VAC/DC . . . . . . . . . . .93
PI6-OC-24VAC/DC . . . . . . . . . . . .93
PI6-OC-5…32VDC . . . . . . . . . . . .93
PI84-012DC-00LD . . . . . . . . . . . .104
Part No.
Pg.
PI84-012DC-00LV . . . . . . . . . . . .104
PI84-024DC-00LD . . . . . . . . . . . .104
PI84-024DC-00LV . . . . . . . . . . . .104
PI84-110DC-00LD . . . . . . . . . . . .104
PI84-110DC-00LV . . . . . . . . . . . .104
PI84-110DC-M43G . . . . . . . . . . .104
PI84-110DC-M93G . . . . . . . . . . .104
PI84-120AC-00LV . . . . . . . . . . . .104
PI84-120AC-M93G . . . . . . . . . . .104
PI84-12DC-M41G . . . . . . . . . . . .104
PI84-12DC-M91G . . . . . . . . . . . .104
PI84-230AC-00LV . . . . . . . . . . . .104
PI84-230AC-M93G . . . . . . . . . . .104
PI84-24DC-M41G . . . . . . . . . . . .104
PI84-24DC-M91G . . . . . . . . . . . .104
PI85-012DC-00LD . . . . . . . . . . . .105
PI85-012DC-00LV . . . . . . . . . . . .105
PI85-024DC-00LD . . . . . . . . . . . .105
PI85-024DC-00LV . . . . . . . . . . . .105
PI85-110DC-00LD . . . . . . . . . . . .105
PI85-110DC-00LV . . . . . . . . . . . .105
PI85-110DC-M43G . . . . . . . . . . .105
PI85-110DC-M93G . . . . . . . . . . .105
PI85-120AC-00LV . . . . . . . . . . . .105
PI85-120AC-M93G . . . . . . . . . . .105
PI85-12DC-M41G . . . . . . . . . . . .105
PI85-12DC-M91G . . . . . . . . . . . .105
PI85-230AC-00LV . . . . . . . . . . . .105
PI85-230AC-M93G . . . . . . . . . . .105
PI85-24DC-M41G . . . . . . . . . . . .105
PI85-24DC-M91G . . . . . . . . . . . .105
PIR2-012DC-00LD . . . . . . . . . . .106
PIR2-012DC-00LV . . . . . . . . . . . .106
PIR2-024DC-00LD . . . . . . . . . . .106
PIR2-024DC-00LV . . . . . . . . . . .106
PIR2-110DC-00LD . . . . . . . . . . .106
PIR2-110DC-00LV . . . . . . . . . . . .106
PIR2-120AC-00LV . . . . . . . . . . .106
PIR2-230AC-00LV . . . . . . . . . . . .106
PIR2M-012DC-20 . . . . . . . . . . . .109
PIR2M-024DC-20 . . . . . . . . . . . .109
PIR2M-110DC-20 . . . . . . . . . . . .109
PIR2M-115AC-20 . . . . . . . . . . . .109
PIR2M-230AC-20 . . . . . . . . . . . .109
PIR3-012DC-00LD . . . . . . . . . . .107
PIR3-012DC-00LV . . . . . . . . . . . .107
PIR3-024DC-00LD . . . . . . . . . . .107
PIR3-024DC-00LV . . . . . . . . . . . .107
PIR3-110DC-00LD . . . . . . . . . . .107
PIR3-110DC-00LV . . . . . . . . . . . .107
PIR3-120AC-00LV . . . . . . . . . . . .107
PIR3-230AC-00LV . . . . . . . . . . . .107
PIR4-012DC-00LD . . . . . . . . . . .108
PIR4-012DC-00LV . . . . . . . . . . . .108
PIR4-024DC-00LD . . . . . . . . . . .108
PIR4-024DC-00LV . . . . . . . . . . .108
PIR4-110DC-00LD . . . . . . . . . . .108
PIR4-110DC-00LV . . . . . . . . . . . .108
PIR4-120AC-00LV . . . . . . . . . . .108
PIR4-230AC-00LV . . . . . . . . . . . .108
PIR6W-1PS-115VAC/DC-C . . . . . .97
PIR6W-1PS-115VAC/DC-O . . . . . .97
PIR6W-1PS-115VAC/DC-R . . . . .96
PIR6W-1PS-115VAC/DC-R01 . . . .96
PIR6W-1PS-115VAC/DC-T . . . . . .97
PIR6W-1PS-12VDC-C . . . . . . . . . .97
PIR6W-1PS-12VDC-O . . . . . . . . . .97
PIR6W-1PS-12VDC-R . . . . . . . . . .96
PIR6W-1PS-12VDC-R01 . . . . . . . .96
PIR6W-1PS-12VDC-T . . . . . . . . . .97
PIR6W-1PS-230VAC/DC-C . . . . . .97
PIR6W-1PS-230VAC/DC-O . . . . . .97
PIR6W-1PS-230VAC/DC-R . . . . . .96
PIR6W-1PS-230VAC/DC-R01 . . . .96
Part No.
Pg.
PIR6W-1PS-24VAC/DC-C . . . . . .97
PIR6W-1PS-24VAC/DC-O . . . . . .97
PIR6W-1PS-24VAC/DC-R . . . . . .96
PIR6W-1PS-24VAC/DC-R01 . . . .96
PIR6W-1PS-24VAC/DC-T . . . . . .97
PIR6W-1PS-24VDC-C . . . . . . . . . .97
PIR6W-1PS-24VDC-O . . . . . . . . . .97
PIR6W-1PS-24VDC-R . . . . . . . . .96
PIR6W-1PS-24VDC-R01 . . . . . . . .96
PIR6W-1PS-24VDC-T . . . . . . . . . .97
PIR6W-1PS-36VDC-C . . . . . . . . . .97
PIR6W-1PS-36VDC-O . . . . . . . . . .97
PIR6W-1PS-36VDC-R . . . . . . . . . .96
PIR6W-1PS-36VDC-R01 . . . . . . . .96
PIR6W-1PS-36VDC-T . . . . . . . . . .97
PIR6W-1PS-42VAC/DC-C . . . . . . .97
PIR6W-1PS-42VAC/DC-O . . . . . . .97
PIR6W-1PS-42VAC/DC-R . . . . . . .96
PIR6W-1PS-42VAC/DC-R01 . . . . .96
PIR6W-1PS-42VAC/DC-T . . . . . . .97
PIR6W-1PS-48VDC-C . . . . . . . . . .97
PIR6W-1PS-48VDC-O . . . . . . . . . .97
PIR6W-1PS-48VDC-R . . . . . . . . . .96
PIR6W-1PS-48VDC-R01 . . . . . . . .96
PIR6W-1PS-48VDC-T . . . . . . . . . .97
PIR6W-1PS-60VDC-C . . . . . . . . . .97
PIR6W-1PS-60VDC-O . . . . . . . . . .97
PIR6W-1PS-60VDC-R . . . . . . . . . .96
PIR6W-1PS-60VDC-R01 . . . . . . . .96
PIR6W-1PS-60VDC-T . . . . . . . . . .97
PIR6W-1PS-6VDC-C . . . . . . . . . . .97
PIR6W-1PS-6VDC-O . . . . . . . . . . .97
PIR6W-1PS-6VDC-R . . . . . . . . . . .96
PIR6W-1PS-6VDC-R01 . . . . . . . . .96
PIR6W-1PS-6VDC-T . . . . . . . . . . .97
PIR6WB-1PS-115VAC/DC-C . . .101
PIR6WB-1PS-115VAC/DC-O . . .101
PIR6WB-1PS-115VAC/DC-R . . .100
PIR6WB-1PS-115VAC/DC-R01 .100
PIR6WB-1PS-115VAC/DC-T . . . .101
PIR6WB-1PS-12VDC-C . . . . . . .101
PIR6WB-1PS-12VDC-O . . . . . . .101
PIR6WB-1PS-12VDC-R . . . . . . .100
PIR6WB-1PS-12VDC-R01 . . . . .100
PIR6WB-1PS-12VDC-T . . . . . . . .101
PIR6WB-1PS-230VAC/DC-C . . .101
PIR6WB-1PS-230VAC/DC-O . . .101
PIR6WB-1PS-230VAC/DC-R . . .100
PIR6WB-1PS-230VAC/DC-R01 .100
PIR6WB-1PS-24VAC/DC-C . . . .101
PIR6WB-1PS-24VAC/DC-O . . . .101
PIR6WB-1PS-24VAC/DC-R . . . .100
PIR6WB-1PS-24VAC/DC-R01 . .100
PIR6WB-1PS-24VAC/DC-T . . . .101
PIR6WB-1PS-24VDC-C . . . . . . .101
PIR6WB-1PS-24VDC-O . . . . . . .101
PIR6WB-1PS-24VDC-R . . . . . . .100
PIR6WB-1PS-24VDC-R01 . . . . .100
PIR6WB-1PS-24VDC-T . . . . . . . .101
PIR6WB-1PS-36VDC-C . . . . . . .101
PIR6WB-1PS-36VDC-O . . . . . . .101
PIR6WB-1PS-36VDC-R . . . . . . .100
PIR6WB-1PS-36VDC-R01 . . . . .100
PIR6WB-1PS-36VDC-T . . . . . . . .101
PIR6WB-1PS-42VAC/DC-C . . . .101
PIR6WB-1PS-42VAC/DC-O . . . .101
PIR6WB-1PS-42VAC/DC-R . . . .100
PIR6WB-1PS-42VAC/DC-R01 . .100
PIR6WB-1PS-42VAC/DC-T . . . . .101
PIR6WB-1PS-48VDC-C . . . . . . .101
PIR6WB-1PS-48VDC-O . . . . . . .101
PIR6WB-1PS-48VDC-R . . . . . . .100
PIR6WB-1PS-48VDC-R01 . . . . .100
PIR6WB-1PS-48VDC-T . . . . . . . .101
Part No.
BOLD - Regular stocked items.
120
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
Pg.
PIR6WB-1PS-60VDC-C . . . . . . .101
PIR6WB-1PS-60VDC-O . . . . . . .101
PIR6WB-1PS-60VDC-R . . . . . . .100
PIR6WB-1PS-60VDC-R01 . . . . .100
PIR6WB-1PS-60VDC-T . . . . . . . .101
PIR6WB-1PS-6VDC-C . . . . . . . .101
PIR6WB-1PS-6VDC-O . . . . . . . .101
PIR6WB-1PS-6VDC-R . . . . . . . .100
PIR6WB-1PS-6VDC-R01 . . . . . .100
PIR6WB-1PS-6VDC-T . . . . . . . . .101
PZ11 . . . . . . . . . . . . . . . . . . . . . . .70
PZ8 . . . . . . . . . . . . . . . . . . . . . . . .69
R15-1014-23-1012 . . . . . . . . . . . .68
R15-1014-23-1012-D . . . . . . . . . .68
R15-1014-23-1012-K . . . . . . . . . .68
R15-1014-23-1012-L . . . . . . . . . . .68
R15-1014-23-1024 . . . . . . . . . . . .68
R15-1014-23-1024-D . . . . . . . . . .68
R15-1014-23-1024-K . . . . . . . . . .68
R15-1014-23-1024-L . . . . . . . . . .68
R15-1014-23-1110 . . . . . . . . . . . .68
R15-1014-23-1110-D . . . . . . . . . .68
R15-1014-23-1110-K . . . . . . . . . .68
R15-1014-23-1110-L . . . . . . . . . . .68
R15-1014-23-3024 . . . . . . . . . . . .68
R15-1014-23-3024-D . . . . . . . . . .68
R15-1014-23-3024-K . . . . . . . . . .68
R15-1014-23-3024-L . . . . . . . . . . .68
R15-1014-23-3120 . . . . . . . . . . . .68
R15-1014-23-3120-D . . . . . . . . . .68
R15-1014-23-3120-K . . . . . . . . . .68
R15-1014-23-3120-L . . . . . . . . . . .68
R15-1014-23-3230 . . . . . . . . . . . .68
R15-1014-23-3230-D . . . . . . . . . .68
R15-1014-23-3230-K . . . . . . . . . .68
R15-1014-23-3230-L . . . . . . . . . . .68
R15-1014-23-6120 . . . . . . . . . . . .68
R15-1014-23-6120-D . . . . . . . . . .68
R15-1014-23-6120-K . . . . . . . . . .68
R15-1014-23-6120-L . . . . . . . . . .68
R15-1014-23-6230 . . . . . . . . . . . .68
R15-1014-23-6230-D . . . . . . . . . .68
R15-1014-23-6230-K . . . . . . . . . .68
R15-1014-23-6230-L . . . . . . . . . . .68
R15-2012-23-1012 . . . . . . . . . . . .68
R15-2012-23-1012-WT . . . . . . . . .68
R15-2012-23-1012-WTL . . . . . . . .68
R15-2012-23-1024 . . . . . . . . . . . .68
R15-2012-23-1024-WT . . . . . . . . .68
R15-2012-23-1024-WTL . . . . . . .68
R15-2012-23-1110 . . . . . . . . . . . .68
R15-2012-23-1110-WT . . . . . . . . .68
R15-2012-23-1110-WTL . . . . . . . .68
R15-2012-23-5024 . . . . . . . . . . . .68
R15-2012-23-5024-WT . . . . . . . . .68
R15-2012-23-5024-WTL . . . . . . . .68
R15-2012-23-5120 . . . . . . . . . . . .68
R15-2012-23-5120-WT . . . . . . . . .68
R15-2012-23-5120-WTL . . . . . . .68
R15-2012-23-5230 . . . . . . . . . . . .68
R15-2012-23-5230-WT . . . . . . . . .68
R15-2012-23-5230-WTL . . . . . . . .68
R15-2013-23-1012 . . . . . . . . . . . .68
R15-2013-23-1012-WT . . . . . . . . .68
R15-2013-23-1012-WTL . . . . . . . .68
R15-2013-23-1024 . . . . . . . . . . . .68
R15-2013-23-1024-WT . . . . . . . . .68
R15-2013-23-1024-WTL . . . . . . .68
R15-2013-23-1110 . . . . . . . . . . . .68
R15-2013-23-1110-WT . . . . . . . . .68
R15-2013-23-1110-WTL . . . . . . . .68
R15-2013-23-5024 . . . . . . . . . . . .68
R15-2013-23-5024-WT . . . . . . . . .68
R15-2013-23-5024-WTL . . . . . . . .68
INDEX
Part No.
Pg.
R15-2013-23-5120 . . . . . . . . . . . .68
R15-2013-23-5120-WT . . . . . . . . .68
R15-2013-23-5120-WTL . . . . . . .68
R15-2013-23-5230 . . . . . . . . . . . .68
R15-2013-23-5230-WT . . . . . . . . .68
R15-2013-23-5230-WTL . . . . . . . .68
R2M-2012-23-1012 . . . . . . . . . . . .62
R2M-2012-23-1024 . . . . . . . . . . .62
R2M-2012-23-1110 . . . . . . . . . . . .62
R2M-2012-23-5120 . . . . . . . . . . .62
R2M-2012-23-5230 . . . . . . . . . . . .62
R2N-2012-23-1012-WT . . . . . . . . .54
R2N-2012-23-1012-WTL . . . . . . .54
R2N-2012-23-1024-WT . . . . . . . .54
R2N-2012-23-1024-WTL . . . . . . .54
R2N-2012-23-1110-WT . . . . . . . . .54
R2N-2012-23-1110-WTL . . . . . . . .54
R2N-2012-23-5024-WT . . . . . . . . .54
R2N-2012-23-5024-WTL . . . . . . .54
R2N-2012-23-5120-WT . . . . . . . .54
R2N-2012-23-5120-WTL . . . . . . .54
R2N-2012-23-5230-WT . . . . . . . . .54
R2N-2012-23-5230-WTL . . . . . . .54
R3N-2013-23-1012-WT . . . . . . . . .54
R3N-2013-23-1012-WTL . . . . . . .54
R3N-2013-23-1024-WT . . . . . . . . .54
R3N-2013-23-1024-WTL . . . . . . .54
R3N-2013-23-1110-WT . . . . . . . . .54
R3N-2013-23-1110-WTL . . . . . . . .54
R3N-2013-23-5024-WT . . . . . . . . .54
R3N-2013-23-5024-WTL . . . . . . . .54
R3N-2013-23-5120-WT . . . . . . . .54
R3N-2013-23-5120-WTL . . . . . . .54
R3N-2013-23-5230-WT . . . . . . . . .54
R3N-2013-23-5230-WTL . . . . . . . .54
R4N-2014-23-1012-WT . . . . . . . . .54
R4N-2014-23-1012-WTL . . . . . . .54
R4N-2014-23-1024-WT . . . . . . . .54
R4N-2014-23-1024-WTL . . . . . . .54
R4N-2014-23-1110-WT . . . . . . . . .54
R4N-2014-23-1110-WTL . . . . . . .54
R4N-2014-23-5024-WT . . . . . . . . .54
R4N-2014-23-5024-WTL . . . . . . .54
R4N-2014-23-5120-WT . . . . . . . .54
R4N-2014-23-5120-WTL . . . . . . .54
R4N-2014-23-5230-WT . . . . . . . . .54
R4N-2014-23-5230-WTL . . . . . . .54
RM40-2011-85-1003 . . . . . . . . . . .75
RM40-2011-85-1005 . . . . . . . . . . .75
RM40-2011-85-1006 . . . . . . . . . . .75
RM40-2011-85-1009 . . . . . . . . . . .75
RM40-2011-85-1012 . . . . . . . . . . .75
RM40-2011-85-1024 . . . . . . . . . . .75
RM40-2011-85-1048 . . . . . . . . . . .75
RM40-3021-85-1003 . . . . . . . . . . .75
RM40-3021-85-1005 . . . . . . . . . . .75
RM40-3021-85-1006 . . . . . . . . . . .75
RM40-3021-85-1009 . . . . . . . . . . .75
RM40-3021-85-1012 . . . . . . . . . . .75
RM40-3021-85-1024 . . . . . . . . . . .75
RM40-3021-85-1048 . . . . . . . . . . .75
RM50-3011-85-1003 . . . . . . . . . . .75
RM50-3011-85-1005 . . . . . . . . . . .75
RM50-3011-85-1006 . . . . . . . . . . .75
RM50-3011-85-1009 . . . . . . . . . . .75
RM50-3011-85-1012 . . . . . . . . . . .75
RM50-3011-85-1018 . . . . . . . . . . .75
RM50-3011-85-1024 . . . . . . . . . . .75
RM50-3011-85-1048 . . . . . . . . . . .75
RM50-3021-85-1003 . . . . . . . . . . .75
RM50-3021-85-1005 . . . . . . . . . . .75
RM50-3021-85-1006 . . . . . . . . . . .75
RM50-3021-85-1009 . . . . . . . . . . .75
RM50-3021-85-1012 . . . . . . . . . . .75
Part No.
Pg.
RM50-3021-85-1018 . . . . . . . . . . .75
RM50-3021-85-1024 . . . . . . . . . . .75
RM50-3021-85-1048 . . . . . . . . . . .75
RM699BV-3011-85-1005 . . . . . . .88
RM699BV-3011-85-1012 . . . . . . .88
RM699BV-3011-85-1024 . . . . . . .88
RM699BV-3011-85-1048 . . . . . . .88
RM699BV-3011-85-1060 . . . . . . .88
RM699BV-3211-85-1005 . . . . . . .88
RM699BV-3211-85-1012 . . . . . . .88
RM699BV-3211-85-1024 . . . . . . .88
RM699BV-3211-85-1048 . . . . . . .88
RM699BV-3211-85-1060 . . . . . . .88
RM84-2012-35-1012 . . . . . . . . . .80
RM84-2012-35-1024 . . . . . . . . . .80
RM84-2012-35-1110 . . . . . . . . . . .80
RM84-2012-35-5120 . . . . . . . . . .80
RM84-2012-35-5230 . . . . . . . . . .80
RM84-2022-35-1012 . . . . . . . . . .80
RM84-2022-35-1024 . . . . . . . . . .80
RM84-2022-35-1110 . . . . . . . . . . .80
RM84-2022-35-5120 . . . . . . . . . .80
RM84-2022-35-5230 . . . . . . . . . .80
RM85-2011-35-1012 . . . . . . . . . .80
RM85-2011-35-1024 . . . . . . . . . .80
RM85-2011-35-1110 . . . . . . . . . . .80
RM85-2011-35-5120 . . . . . . . . . .80
RM85-2011-35-5230 . . . . . . . . . .80
RM85-2021-35-1012 . . . . . . . . . .80
RM85-2021-35-1024 . . . . . . . . . .80
RM85-2021-35-1110 . . . . . . . . . . .80
RM85-2021-35-5120 . . . . . . . . . .80
RM85-2021-35-5230 . . . . . . . . . .80
RM87N-2011-35-1012 . . . . . . . . .80
RM87N-2011-35-1024 . . . . . . . . .80
RM87N-2011-35-1110 . . . . . . . . .80
RM87N-2011-35-5120 . . . . . . . . .80
RM87N-2011-35-5230 . . . . . . . . .80
RM87N-2021-35-1012 . . . . . . . . .80
RM87N-2021-35-1024 . . . . . . . . .80
RM87N-2021-35-1110 . . . . . . . . .80
RM87N-2021-35-5120 . . . . . . . . .80
RM87N-2021-35-5230 . . . . . . . . .80
RS35-3022-25-1012 . . . . . . . . . .103
RS35-3022-25-1024 . . . . . . . . . .103
RS35-3022-25-1110 . . . . . . . . . .103
RS50-3022-25-1012 . . . . . . . . . .103
RS50-3022-25-1024 . . . . . . . . . .103
RS50-3022-25-1110 . . . . . . . . . .103
RSR30-D05-A1-24-020-1 . . . . . . .84
RSR30-D05-D1-02-040-1 . . . . . .86
RSR30-D05-D1-04-025-1 . . . . . .85
RSR30-D05-D1-24-010-1 . . . . . .87
RSR30-D12-A1-24-020-1 . . . . . . .84
RSR30-D12-D1-02-040-1 . . . . . .86
RSR30-D12-D1-04-025-1 . . . . . .85
RSR30-D12-D1-24-010-1 . . . . . .87
RSR30-D24-A1-24-020-1 . . . . . . .84
RSR30-D24-D1-02-040-1 . . . . . .86
RSR30-D24-D1-04-025-1 . . . . . .85
RSR30-D24-D1-24-010-1 . . . . . .87
RSR30-D48-D1-02-040-1 . . . . . .86
RSR30-D48-D1-04-025-1 . . . . . .85
RSR30-D48-D1-24-010-1 . . . . . .87
RUC-2012-26-1012 . . . . . . . . . . .62
RUC-2012-26-1012-K . . . . . . . . . .62
RUC-2012-26-1012-KL . . . . . . . . .62
RUC-2012-26-1012-L . . . . . . . . . .62
RUC-2012-26-1024 . . . . . . . . . . .62
RUC-2012-26-1024-K . . . . . . . . . .62
RUC-2012-26-1024-KL . . . . . . . .62
RUC-2012-26-1024-L . . . . . . . . . .62
RUC-2012-26-1110 . . . . . . . . . . . .62
RUC-2012-26-1110-K . . . . . . . . . .62
Part No.
Pg.
RUC-2012-26-1110-KL . . . . . . . . .62
RUC-2012-26-1110-L . . . . . . . . . .62
RUC-2012-26-5120 . . . . . . . . . . .62
RUC-2012-26-5120-K . . . . . . . . . .62
RUC-2012-26-5120-KL . . . . . . . .62
RUC-2012-26-5120-L . . . . . . . . . .62
RUC-2012-26-5230 . . . . . . . . . . . .62
RUC-2012-26-5230-K . . . . . . . . . .62
RUC-2012-26-5230-KL . . . . . . . .62
RUC-2012-26-5230-L . . . . . . . . . .62
RUC-2013-26-1012 . . . . . . . . . . .63
RUC-2013-26-1012-K . . . . . . . . . .63
RUC-2013-26-1012-KL . . . . . . . . .63
RUC-2013-26-1012-L . . . . . . . . . .63
RUC-2013-26-1024 . . . . . . . . . . .63
RUC-2013-26-1024-K . . . . . . . . . .63
RUC-2013-26-1024-KL . . . . . . . .63
RUC-2013-26-1024-L . . . . . . . . . .63
RUC-2013-26-1110 . . . . . . . . . . . .63
RUC-2013-26-1110-K . . . . . . . . . .63
RUC-2013-26-1110-KL . . . . . . . . .63
RUC-2013-26-1110-L . . . . . . . . . .63
RUC-2013-26-5120 . . . . . . . . . . .63
RUC-2013-26-5120-K . . . . . . . . . .63
RUC-2013-26-5120-KL . . . . . . . .63
RUC-2013-26-5120-L . . . . . . . . . .63
RUC-2013-26-5230 . . . . . . . . . . .63
RUC-2013-26-5230-K . . . . . . . . . .63
RUC-2013-26-5230-KL . . . . . . . . .63
RUC-2013-26-5230-L . . . . . . . . . .63
RUC-2022-26-1012 . . . . . . . . . . . .63
RUC-2022-26-1012-K . . . . . . . . . .63
RUC-2022-26-1012-KL . . . . . . . . .63
RUC-2022-26-1012-L . . . . . . . . . .63
RUC-2022-26-1024 . . . . . . . . . . . .63
RUC-2022-26-1024-K . . . . . . . . . .63
RUC-2022-26-1024-KL . . . . . . . . .63
RUC-2022-26-1024-L . . . . . . . . . .63
RUC-2022-26-1110 . . . . . . . . . . . .63
RUC-2022-26-1110-K . . . . . . . . . .63
RUC-2022-26-1110-KL . . . . . . . . .63
RUC-2022-26-1110-L . . . . . . . . . .63
RUC-2022-26-5120 . . . . . . . . . . . .63
RUC-2022-26-5120-K . . . . . . . . . .63
RUC-2022-26-5120-KL . . . . . . . . .63
RUC-2022-26-5120-L . . . . . . . . . .63
RUC-2022-26-5230 . . . . . . . . . . . .63
RUC-2022-26-5230-K . . . . . . . . . .63
RUC-2022-26-5230-KL . . . . . . . . .63
RUC-2022-26-5230-L . . . . . . . . . .63
RUC-2023-26-1012 . . . . . . . . . . . .63
RUC-2023-26-1012-K . . . . . . . . . .63
RUC-2023-26-1012-KL . . . . . . . . .63
RUC-2023-26-1012-L . . . . . . . . . .63
RUC-2023-26-1024 . . . . . . . . . . . .63
RUC-2023-26-1024-K . . . . . . . . . .63
RUC-2023-26-1024-KL . . . . . . . . .63
RUC-2023-26-1024-L . . . . . . . . . .63
RUC-2023-26-1110 . . . . . . . . . . . .63
RUC-2023-26-1110-K . . . . . . . . . .63
RUC-2023-26-1110-KL . . . . . . . . .63
RUC-2023-26-1110-L . . . . . . . . . .63
RUC-2023-26-5120 . . . . . . . . . . . .63
RUC-2023-26-5120-K . . . . . . . . . .63
RUC-2023-26-5120-KL . . . . . . . . .63
RUC-2023-26-5120-L . . . . . . . . . .63
RUC-2023-26-5230 . . . . . . . . . . . .63
RUC-2023-26-5230-K . . . . . . . . . .63
RUC-2023-26-5230-KL . . . . . . . . .63
RUC-2023-26-5230-L . . . . . . . . . .63
RUC-2052-26-1012 . . . . . . . . . . . .64
RUC-2052-26-1012-K . . . . . . . . . .64
RUC-2052-26-1012-KL . . . . . . . . .64
RUC-2052-26-1012-L . . . . . . . . . .64
Part No.
Pg.
RUC-2052-26-1024 . . . . . . . . . . . .64
RUC-2052-26-1024-K . . . . . . . . . .64
RUC-2052-26-1024-KL . . . . . . . . .64
RUC-2052-26-1024-L . . . . . . . . . .64
RUC-2052-26-1110 . . . . . . . . . . . .64
RUC-2052-26-1110-K . . . . . . . . . .64
RUC-2052-26-1110-KL . . . . . . . . .64
RUC-2052-26-1110-L . . . . . . . . . .64
RUC-2052-26-5120 . . . . . . . . . . . .64
RUC-2052-26-5120-K . . . . . . . . . .64
RUC-2052-26-5120-KL . . . . . . . . .64
RUC-2052-26-5120-L . . . . . . . . . .64
RUC-2052-26-5230 . . . . . . . . . . . .64
RUC-2052-26-5230-K . . . . . . . . . .64
RUC-2052-26-5230-KL . . . . . . . . .64
RUC-2052-26-5230-L . . . . . . . . . .64
RUC-2053-26-1012 . . . . . . . . . . . .64
RUC-2053-26-1012-K . . . . . . . . . .64
RUC-2053-26-1012-KL . . . . . . . . .64
RUC-2053-26-1012-L . . . . . . . . . .64
RUC-2053-26-1024 . . . . . . . . . . . .64
RUC-2053-26-1024-K . . . . . . . . . .64
RUC-2053-26-1024-KL . . . . . . . . .64
RUC-2053-26-1024-L . . . . . . . . . .64
RUC-2053-26-1110 . . . . . . . . . . . .64
RUC-2053-26-1110-K . . . . . . . . . .64
RUC-2053-26-1110-KL . . . . . . . . .64
RUC-2053-26-1110-L . . . . . . . . . .64
RUC-2053-26-5120 . . . . . . . . . . . .64
RUC-2053-26-5120-K . . . . . . . . . .64
RUC-2053-26-5120-KL . . . . . . . . .64
RUC-2053-26-5120-L . . . . . . . . . .64
RUC-2053-26-5230 . . . . . . . . . . . .64
RUC-2053-26-5230-K . . . . . . . . . .64
RUC-2053-26-5230-KL . . . . . . . . .64
RUC-2053-26-5230-L . . . . . . . . . .64
RY2-2012-26-1012 . . . . . . . . . . . .62
RY2-2012-26-1012-D . . . . . . . . . .62
RY2-2012-26-1012-L . . . . . . . . . .62
RY2-2012-26-1012-LD . . . . . . . . .62
RY2-2012-26-1024 . . . . . . . . . . . .62
RY2-2012-26-1024-D . . . . . . . . . .62
RY2-2012-26-1024-L . . . . . . . . . .62
RY2-2012-26-1024-LD . . . . . . . . .62
RY2-2012-26-1110 . . . . . . . . . . . .62
RY2-2012-26-1110-D . . . . . . . . . .62
RY2-2012-26-1110-L . . . . . . . . . .62
RY2-2012-26-1110-LD . . . . . . . . .62
RY2-2012-26-5024 . . . . . . . . . . . .62
RY2-2012-26-5024-D . . . . . . . . . .62
RY2-2012-26-5024-L . . . . . . . . . .62
RY2-2012-26-5024-LD . . . . . . . . .62
RY2-2012-26-5120 . . . . . . . . . . . .62
RY2-2012-26-5120-D . . . . . . . . . .62
RY2-2012-26-5120-L . . . . . . . . . .62
RY2-2012-26-5120-LD . . . . . . . . .62
RY2-2012-26-5230 . . . . . . . . . . . .62
RY2-2012-26-5230-D . . . . . . . . . .62
RY2-2012-26-5230-L . . . . . . . . . .62
RY2-2012-26-5230-LD . . . . . . . . .62
BOLD - Regular stocked items.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
121
STANDARD TERMS AND CONDITIONS OF SALE
TITLE - Title to the products of ALTECH shall remain with ALTECH until
payment is made in full by Customer. Such reservation of title is for the
purpose of securing the purchase price and shall not relieve Customer of the
duty to inspect the products upon receipt, to notify ALTECH of any
deficiencies or defects, and to exercise due care in the use, installation,
operation, and maintenance of the products when on the premise of the
Customer or under the control of the Customer. Notwithstanding any
reservation of title by ALTECH, risk of loss shall pass to customer at any time
of shipment.
SHIPMENT AND DELIVERY - All orders for destination in the mainland
United States (less Hawaii, Alaska and non-continental United States
possessions) will be shipped F.O.B. Flemington, N.J. All destination, shipping
and other charges shall be paid by the Customer in accordance with
ALTECH’s then current shipping and billing practices.
Delivery dates given in the acceptance of any order are approximate.
ALTECH shall not be liable for delays in delivery or in performance due to
causes beyond its reasonable control including acts of God, acts of
Customer, acts of civil or military authority, fires, strikes or other labor
disturbances, war, riot or delays in transportation. In the event of such delay,
the date of delivery or performance shall be extended for a period equal to
the time lost by reason of the delay.
PRICE - PRICES in any ALTECH publication are subject to change
without prior notification. Catalog prices are based on prices published in the
current price list. All written quotations are valid for thirty (30) days from the
date of quotation. Customer shall pay all sales, use, excise or similar taxes
whenever ALTECH must itself pay and/or collect such tax from Customer
arising out of the sale.
PAYMENT - Customer agrees to make payment within thirty (30) days of
date of the invoice from ALTECH. Customer agrees to pay a late payment
charge of one and one-half percent (1.5% per month, or the maximum late
payment charge permitted by applicable law, whichever is less, on any
unpaid amount for each calendar month (or fraction thereof) that such
payment is in default. Orders amounting to less than $100.00 will be billed at
$100.00 plus freight. Full carton purchases are required. In the event of
referral to an attorney for collection, reasonable attorney’s fees for collection
of the overdue amount shall be paid by Customer. In the event payment is not
received within 30 days from the date of invoice, any discount shall be
cancelled and the full list price will be due.
LIMITED WARRANTY - ALTECH warrants to Customer that the
equipment purchases shall be free from defects in material and workmanship
under normal use and service for a period of one year from shipment.
Written notice as an explanation of the circumstances of any claim that
the equipment has proved defective in material or workmanship shall be
given promptly by the Customer to ALTECH.
ALTECH will not be liable for any misuse, improper operations, improper
installation, improper maintenance, alteration, modification, accident or
unusual degradation of the equipment or parts due to an unsuitable
installation environment.
No representation of other affirmation of facts, including but not limited to
statements regarding capacity, suitability for use or performance of the
equipment, shall be or be deemed to be a warranty or representation by
ALTECH for any purpose, nor give rise to any liability or obligation of ALTECH
whatsoever.
Customer’s sole and exclusive remedy in the event of breach of warranty,
as set forth herein, is expressly limited to (1) the correction of the defect by
adjustment, repair, modification, or replacement, or (2) issuance of a credit or
refund of the purchase price for the defective equipment at ALTECH’s
election and sole expense.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE
ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANTIES OR MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY EXTENDS ONLY TO THE CUSTOMER FROM ALTECH
OR ITS AUTHORIZED DISTRIBUTOR.
LIMITATION OF LIABILITY - IN NO EVENT, SHALL ALTECH BE LIABLE
FOR LOSS OF PROFITS, INDIRECT, SPECIAL, CONSEQUENTIAL OR
OTHER SIMILAR DAMAGES ARISING OUT OF ANY BREACH OF THIS
AGREEMENT OR OBLIGATIONS UNDER THE AGREEMENT.
ALTECH SHALL NOT BE LIABLE FOR ANY DAMAGES CAUSED BY
DELAY IN SHIPMENT, INSTALLATION OR FURNISHING OF EQUIPMENT OR
SERVICES UNDER THIS AGREEMENT.
No action arising out of any claimed breach of this Agreement may be
brought by either party more than two (2) years after the cause of action has
accrued.
122
PATENT INDEMNITY - ALTECH shall defend or settle any suit or
proceeding brought against Customer based on a claim that any equipment
made to ALTECH design and furnished hereunder constitutes an infringement
of any existing United States patent, provided (ALTECH) is notified promptly
in writing and is given complete authorization and information required for the
defense, and ALTECH shall pay all damages and costs awarded against
Customer, but shall not be responsible for any costs, expense or compromise
incurred or made by Customer without ALTECH’s prior written consent. If any
equipment is in ALTECH’s opinion likely to or does become the subject of a
claim for patent infringement, ALTECH may at its option and expense procure
for Customer the right to continue using the device, modify it to become noninfringing, but in the event ALTECH is not reasonably able to modify,
substitute, or otherwise procure for Customer the right to continue using it,
ALTECH will remove such equipment and refund to Customer the amount
paid in excess of a reasonable rental for past use.
ALTECH shall not be liable for any infringement or claim based upon use
of the equipment in combination with other equipment not supplied by
ALTECH or with modifications made by Customer.
The foregoing states the entire liability of ALTECH to Customer arising
from patent infringement.
SELLER’S REMEDIES - Should Customer fail to make any payment
within ten (10) days of its due date, or fail to perform any other of the
Customer’s obligation hereunder upon thirty (30) days written notice, or
should Customer be or become insolvent or be a party to any bankruptcy
receivership proceeding prior to full payment of all amounts payable
hereunder, ALTECH may: (a) with or without demand or notice to customer
declare the entire amount unpaid immediately due and payable; (b) enter
upon the premises where the equipment may be found and remove it
(Customer shall assemble the equipment and make it available to ALTECH at
a place reasonably convenient to both parties and shall permit and assist
ALTECH in effecting the retaking and removal of the equipment); and (c) sell
any or all the equipment as permitted under applicable law, applying the
proceeds of the sale to payment of the expenses of retaking, repairing and
selling the equipment, reasonable attorney fees and to the satisfaction of all
indebtedness then due and unpaid under this Agreement. Any surplus shall
be paid to Customer and any deficiency shall be paid to ALTECH by
Customer.
The remedies provided herein shall be cumulative and in addition to all
other remedies provided by law or equity or under the Uniform Commercial
Code.
GOVERNING LAW - This agreement will be governed by the Laws of the
State of New Jersey.
GENERAL - This Agreement shall only become effective and binding
when either (a) it has been accepted and executed by an authorized
representative of ALTECH, or (b) the equipment has been shipped to
Customer, with or without acceptance in writing hereon. Notice of
acceptance is hereby waived by Customer. Customer hereby acknowledges
receipt of a true and complete copy hereof.
No addition to or modification of any of the Terms and Conditions of Sale
as they appear herein shall be binding upon ALTECH unless signed in writing
by duly authorized representative of ALTECH in Flemington, N.J.
Typographical and clerical errors in quotations, orders and
acknowledgments are subject to correction.
This Agreement is not assignable without the prior written consent of
ALTECH. Any attempt to assign any of the rights, duties or obligations of this
Agreement without such consent is void.
If any provision or provisions of this Agreement shall be held to be invalid,
illegal or unenforceable, the validity, legality and enforceability, of the
remaining provisions shall not in any way be affected or impaired thereby.
ALTECH is not responsible for failure to fulfill its obligation under this
Agreement due to causes beyond its control, or except as agreed herein.
THE CUSTOMER ACKNOWLEDGES THAT HE HAS READ THE
AGREEMENT, UNDERSTANDS IT, AND AGREES TO BE BOUND BY ITS
TERMS AND CONDITIONS. FURTHERMORE, THE CUSTOMER AGREES
THAT IT IS THE COMPLETE AND EXCLUSIVE STATEMENT OF THE
AGREEMENT BETWEEN THE PARTIES, WHICH SUPERSEDES ALL
PROPOSALS OR PRIOR AGREEMENTS, ORAL OR WRITTEN, EXPRESSED
OR IMPLIED, AND ALL OTHER COMMUNICATIONS BETWEEN THE
PARTIES RELATING TO THE SUBJECT MATTER OF THIS AGREEMENT.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
HERE ARE OTHER GREAT PRODUCTS
AVAILABLE FROM ALTECH
Circuit Protection Devices
Metallic Push Buttons and Selector Switches
Altech 22 and 30 mm Push Buttons offer ideal cost-effective
solutions for control circuits utilizing both direct and remote
management applications. Ease of assembly has been
engineered into the design; the only tool necessary for
installation is a screwdriver.
• LED Indicating Devices
• Pilot Lights
• Push Button Stations
• Push Button Enclosures
• UL Recognized
• Custom Push Button Assemblies
• All Very Competitively Priced
Altech the market leader in UL508 Manual
Motor Controllers/ Miniature Circuit Breakers
now introduces UL489 Miniature Circuit
Breakers and UL1077 Supplementary
Protectors. The UL489 versions are DIN rail
mounted, 17.5mm wide, thermal magnetic,
240V, 480Y/277V AC, 50/60Hz, 125 and 250
VDC models, with short circuit interrupt
capacity of 10kA, a positive trip indicator, and
are line/load reversible. The UL1077 versions
are DIN rail mounted, 17.5mm wide, thermal
magnetic, 480Y/277V AC, 50/60Hz, a short
circuit withstand capacity 10kA, have a
positive trip indicator.
Altech Corp.®
35 Royal Rd., Flemington, NJ 08822
908-806-9400
FAX 908-806-9490
www.altechcorp.com
Contactors and More!
Altech Corp.®
35 Royal Rd., Flemington, NJ 08822
908-806-9400
FAX 908-806-9490
www.altechcorp.com
Terminal Blocks
Altech’s now carries contactors, mini
contactors, definite purpose contactors &
overload relays. The contactors come in 3
and 4 pole configurations at 9A to 800A.
Available in Single Phase (115 -230V) and
Three Phase (200 - 575V) AC and DC
models. A large variety of coil voltages are
supported and the accessories are auxiliary
contacts and overload relays. The mini
contactors come in screw clamp, fast-on,
cage clamp and solder pin types.
Altech offers a NEW Terminal Block catalog
with the most competitively priced blocks in
the industry. We feature screw and spring
clamp models for DIN rail and panel mount
applications. This advanced line of wire
termination products will increase your
design options and help to get the job done
more efficiently. Our line of blocks include
feed-through (single, double or triple level),
distribution, ground, fuse, disconnect,
thermocouple, surge suppressor and
indicator. A wide variety of accessories, tools
and ferrules are available.
Altech Corp.®
35 Royal Rd., Flemington, NJ 08822
908-806-9400
FAX 908-806-9490
www.altechcorp.com
Altech Corp.®
35 Royal Rd., Flemington, NJ 08822
908-806-9400
www.altechcorp.com
Industrial Enclosures
DIN Rail Power Supplies
Altech’s expanded line of TK Industrial
Enclosures, with metric knockouts, is here.
Now our entire line of industrial enclosures is
in metric. Metric knockouts align with
international standards making selection
easier and more universal. Plus the PG
standard is still available. All of Altech’s
enclosures are internationally accepted and
stand up to the harshest environments. They
protect against dust, water and corrosion
while enhancing the value of your product.
Rated up to IP66 (NEMA type 4x), Altech
enclosures are available in a wide range of
sizes.
Altech Corp.®
35 Royal Rd., Flemington, NJ 08822
908-806-9400
www.altechcorp.com
Altech DIN RAIL mountable power supplies
have Universal AC input. They are suitable for
industrial and automation applications.
• UL508 Listed
• Installed on DIN rail TS35/ 7.5 or 15
• Available from 20-960W
• Protections: Short circuit / Overload /
Over-voltage / Over temperature
• Cooling by free air convection
• Worldwide approvals
• 3 year warranty
Altech Corp.®
35 Royal Rd., Flemington, NJ 08822
908-806-9400
FAX 908-806-9490
www.altechcorp.com
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
DATA SUBJECT TO CHANGE WITHOUT NOTICE
123
Altech Corporation
35 Royal Road
Flemington, NJ 08822-6000
P 908.806.9400 • F 908.806.9490
www.altechcorp.com
Altech Corp.® 410-112013-5M
Printed November 2013
工商网监
湘ICP备2023018690号
