1TC158-80A

APD_System_Brochure.QXD_Layout 1 6/8/11 9:51 AM Page 1 FIXING AND MOUNTING Insulation Cap End Support Modular APD System Part No. 19FT3V Part No. 17BI0 Part No. 17BS Material including Noryl 2 Screws M4x30mm built-in insulation cap Material Length PVC 30 mm Material including Noryl Screw M4x25 The holder can accommodate up to 3 Busbars (6 conductor circuits) Slide in insulation cap from the side into insulation. If an end support is used, no insulation cap (Part No. 17BIO) is necessary Altech’s Modular Power Distribution (APD) System is a new way to simplify existing wiring methods! The modular APD system provides flexible solutions for busing common power to many different electrical components. Components can be easily added or removed using quick disconnects saving valuable time and cost during installation and maintenance. The APD system also provides an organized method of wiring, that would simplify the wiring schematics for troubleshooting, while reducing the use of excessive wires and cables. The APD system allows multiple connections per phase for many applications, such as: insulation cap • Supplying separate voltages to auxiliary circuits and control circuits for relays, contactors, timers, etc. • Supplying power to circuit breakers, motor starters, switches, contactors, etc. Busbar Holder Marking Set Ø8.2mm 14.5 14.5 1.5 60 +0.2 0 +0.1 17EET cover -PVC label - Paper 9mm - 0.3 Part No. Material +0.3 Holders should be set approx. every 500mm (19.69 in.). For each Busbar to be fixed cut 2 braces out of the holder, keep the others to assure stability 30mm - 0.6 Modular APD System Bar-Holder Two conductors are housed within a rigid plastic insulation housing suitable for voltages up to 600VAC. The conductors have current ratings of 25A, 63A or 80A. The entire system is touch proof (IP20). The bar-holder has engraved numerical identification from 1-12. The bar-holder can also accommodate 42x25 mm (1.65 x 0.98 in.) labels and a transparent protection cover. This marking-set is available as part no. 17EET; it contains one label with 6 positions for marking and one transparent cover in PVC. Altech Corporation 35 Royal Road Flemington, NJ 08822 t 908-806-9400 f 908-806-9490 www.altechcorp.com 349-062011-1K Altech Corp.® • t 908-806-9400 • f 908-806-9490 • www.altechcorp.com APD_System_Brochure.QXD_Layout 1 6/8/11 9:51 AM Page 3 APD BUSBARS POWER FEEDING AND CONNECTION End Support (17BS) Specifications: APD Busbars are available with 1 or 2 phases, Max. Temperature 158°F (70°C) Material Insulation: PVC Length: 1.9m (6.23 ft.)/ 1.0m (3.281 ft.) 15 15 45A 29.5 APD Busbar 50 90A Power Input Connector (40017) 19.5 Power Input Connector Part No. Material Clamp Wire Size Electrical Rating 40017 Copper/Steel 8-2AWG (10-25mm2) 90A (600VAC) 45A Electrical Rating (600VAC) 25A 25A 25A 25A 63A 63A 63A 63A 80A 80A 80A 80A Part No. 1LB158-25A 2LB158-25A 1LB83-25A 2LB83-25A 1TC158-63A 2TC158-63A 1TC83-63A 2TC83-63A 1TC158-80A 2TC158-80A 1TC83-80A 2TC83-80A Possible Connections / Phase 158 158 83 83 158 158 83 83 158 158 83 83 C O N TA C T A LT E C H FOR No. of Phases 1 2 1 2 1 2 1 2 1 2 1 2 Material Length Brass Brass Brass Brass Tinned Copper Tinned Copper Tinned Copper Tinned Copper Tinned Copper Tinned Copper Tinned Copper Tinned Copper 1.9m (6.23 ft.) 1.9m (6.23 ft.) 1.0m (3.281 ft.) 1.0m (3.281 ft.) 1.9m (6.23 ft.) 1.9m (6.23 ft.) 1.0m (3.281 ft.) 1.0m (3.281 ft.) 1.9m (6.23 ft.) 1.9m (6.23 ft.) 1.0m (3.281 ft.) 1.0m (3.281 ft.) CUSTOM CONFIGURATIONS. 90A can be distributed over a 63A APD Busbar by using the Power Input Connector as a feeder in the center of the busbar. Note: Standard Female Quick Disconnects (0.250 x 0.032 in.) can be used for power feeding and between-busbar connections of up to 30A. Power Input Connectors (Part No. 40017) are only necessary for currents greater than 30A. Connection of Branch Circuits The APD Busbar have standard pins (6.3mm x 0.8mm) for female disconnects every 12mm. 83 disconnects are available per meter. Standard 0.250 in. female disconnects can be used for connections to achieve the following current ratings: 30A 20A 15A 10A 13 mm 4.6 mm 30 mm with with with with Technical Note: The standard busbar lengths can be cut to any desirable length. When cutting the busbars remember to cut the conductor 62mm shorter than the insulation to ensure space for the insulation cap (Part No. 17BI0) at each end. This guarantees adequate and required creepage distance (see picture below). If an end support (Part No. 17BS) is used then no insulation cap is needed. 10AWG 12AWG 14AWG 16AWG 6.3 mm wire wire wire wire 12 mm 31 mm 31 mm insulation cap Altech Corp.® • t 908-806-9400 • f 908-806-9490 • www.altechcorp.com 8 mm 19.8 mm 5.7 mm insulation cap Altech Corp.® • t 908-806-9400 • f 908-806-9490 • www.altechcorp.com Modular APD System Bar Holder (19FT3V) The Power Input Connector is optional. It can accommodate wires from 8 to 2AWG and is used for circuits up to 90A. 4.6 mm Modular APD System 83 Connections per Meter per Phase APD_System_Brochure.QXD_Layout 1 6/8/11 9:51 AM Page 3 APD BUSBARS POWER FEEDING AND CONNECTION End Support (17BS) Specifications: APD Busbars are available with 1 or 2 phases, Max. Temperature 158°F (70°C) Material Insulation: PVC Length: 1.9m (6.23 ft.)/ 1.0m (3.281 ft.) 15 15 45A 29.5 APD Busbar 50 90A Power Input Connector (40017) 19.5 Power Input Connector Part No. Material Clamp Wire Size Electrical Rating 40017 Copper/Steel 8-2AWG (10-25mm2) 90A (600VAC) 45A Electrical Rating (600VAC) 25A 25A 25A 25A 63A 63A 63A 63A 80A 80A 80A 80A Part No. 1LB158-25A 2LB158-25A 1LB83-25A 2LB83-25A 1TC158-63A 2TC158-63A 1TC83-63A 2TC83-63A 1TC158-80A 2TC158-80A 1TC83-80A 2TC83-80A Possible Connections / Phase 158 158 83 83 158 158 83 83 158 158 83 83 C O N TA C T A LT E C H FOR No. of Phases 1 2 1 2 1 2 1 2 1 2 1 2 Material Length Brass Brass Brass Brass Tinned Copper Tinned Copper Tinned Copper Tinned Copper Tinned Copper Tinned Copper Tinned Copper Tinned Copper 1.9m (6.23 ft.) 1.9m (6.23 ft.) 1.0m (3.281 ft.) 1.0m (3.281 ft.) 1.9m (6.23 ft.) 1.9m (6.23 ft.) 1.0m (3.281 ft.) 1.0m (3.281 ft.) 1.9m (6.23 ft.) 1.9m (6.23 ft.) 1.0m (3.281 ft.) 1.0m (3.281 ft.) CUSTOM CONFIGURATIONS. 90A can be distributed over a 63A APD Busbar by using the Power Input Connector as a feeder in the center of the busbar. Note: Standard Female Quick Disconnects (0.250 x 0.032 in.) can be used for power feeding and between-busbar connections of up to 30A. Power Input Connectors (Part No. 40017) are only necessary for currents greater than 30A. Connection of Branch Circuits The APD Busbar have standard pins (6.3mm x 0.8mm) for female disconnects every 12mm. 83 disconnects are available per meter. Standard 0.250 in. female disconnects can be used for connections to achieve the following current ratings: 30A 20A 15A 10A 13 mm 4.6 mm 30 mm with with with with Technical Note: The standard busbar lengths can be cut to any desirable length. When cutting the busbars remember to cut the conductor 62mm shorter than the insulation to ensure space for the insulation cap (Part No. 17BI0) at each end. This guarantees adequate and required creepage distance (see picture below). If an end support (Part No. 17BS) is used then no insulation cap is needed. 10AWG 12AWG 14AWG 16AWG 6.3 mm wire wire wire wire 12 mm 31 mm 31 mm insulation cap Altech Corp.® • t 908-806-9400 • f 908-806-9490 • www.altechcorp.com 8 mm 19.8 mm 5.7 mm insulation cap Altech Corp.® • t 908-806-9400 • f 908-806-9490 • www.altechcorp.com Modular APD System Bar Holder (19FT3V) The Power Input Connector is optional. It can accommodate wires from 8 to 2AWG and is used for circuits up to 90A. 4.6 mm Modular APD System 83 Connections per Meter per Phase APD_System_Brochure.QXD_Layout 1 6/8/11 9:51 AM Page 1 FIXING AND MOUNTING Insulation Cap End Support Modular APD System Part No. 19FT3V Part No. 17BI0 Part No. 17BS Material including Noryl 2 Screws M4x30mm built-in insulation cap Material Length PVC 30 mm Material including Noryl Screw M4x25 The holder can accommodate up to 3 Busbars (6 conductor circuits) Slide in insulation cap from the side into insulation. If an end support is used, no insulation cap (Part No. 17BIO) is necessary Altech’s Modular Power Distribution (APD) System is a new way to simplify existing wiring methods! The modular APD system provides flexible solutions for busing common power to many different electrical components. Components can be easily added or removed using quick disconnects saving valuable time and cost during installation and maintenance. The APD system also provides an organized method of wiring, that would simplify the wiring schematics for troubleshooting, while reducing the use of excessive wires and cables. The APD system allows multiple connections per phase for many applications, such as: insulation cap • Supplying separate voltages to auxiliary circuits and control circuits for relays, contactors, timers, etc. • Supplying power to circuit breakers, motor starters, switches, contactors, etc. Busbar Holder Marking Set Ø8.2mm 14.5 14.5 1.5 60 +0.2 0 +0.1 17EET cover -PVC label - Paper 9mm - 0.3 Part No. Material +0.3 Holders should be set approx. every 500mm (19.69 in.). For each Busbar to be fixed cut 2 braces out of the holder, keep the others to assure stability 30mm - 0.6 Modular APD System Bar-Holder Two conductors are housed within a rigid plastic insulation housing suitable for voltages up to 600VAC. The conductors have current ratings of 25A, 63A or 80A. The entire system is touch proof (IP20). The bar-holder has engraved numerical identification from 1-12. The bar-holder can also accommodate 42x25 mm (1.65 x 0.98 in.) labels and a transparent protection cover. This marking-set is available as part no. 17EET; it contains one label with 6 positions for marking and one transparent cover in PVC. Altech Corporation 35 Royal Road Flemington, NJ 08822 t 908-806-9400 f 908-806-9490 www.altechcorp.com 349-062011-1K Altech Corp.® • t 908-806-9400 • f 908-806-9490 • www.altechcorp.com