601.9261.018

Technical Data Safety switch Series Safety Hinge Switch SHS Description SHS-A1Z-SR-BG Article number 6019261018 Circuit diagram Operating diagram Fixing point Fixing point in the range 0° ... 180° freely selectable Connection le ng el a wiv s ON OFF Tolerances: switching angle (opening) +2,0 ° / -1,5 °, direct opening torque 10 %, direct opening angle +0,5 ° / -3 ° Switching angle hysteresis (closing the N.C. contact –1,0 °) from the hinge’s typical switch-off point Illustration with fixed shaft and sheared-off set screw. BERNSTEIN AG . Hans-Bernstein-Straße 1 . 32457 Porta Westfalica . www.bernstein.eu Technical modifications and errors excepted. The technical datasheet corresponds to the technical state as of 2016-01-07 and will not be removed in case of changes. Page 1 of 3 6019261018 / 2017-16 Technical Data Electrical Data Rated insulation voltage Rated impulse withstand voltage Conv. thermal current Rated operational voltage Utilization category Direct opening action Short-circuit protective device Protection class Ui Uimp Ithe Ue � 250 V 2,5 kV 3A 230 V AC / 60 V DC AC-15, 230 V AC / 1,5 A, DC-13, 60 V DC / 0,5 A acc. to IEC/EN 60947-5-1, annex K Fuse 4 A gG I Mechanical data Enclosure Cover Wing Ambient air temperature Contact type Mechanical life Switching frequency Attachment Connection type Weight Installation position Protection type Switching angle Direct opening angle Direct opening torque Mechanical load (see dimensioned drawing for the introduction direction of the forces) GD-Zn GD-Zn GD-Zn -25 °C to +70 °C 1 NC 1 x 106 operating cycles max. 1200 switching operations / hour 4 x M6 screws DIN 7984 or DIN 6912 Plug M12x1, metal thread ≈ 0,4 kg operator definable IP 67 in acc. with IEC/EN 60529 +/- 3 ° from fixing point +/- 10 ° from fixing point 1,5 Nm FR1= max. 1000 N FR2= max. 500 N FA = max. 750 N ID for safety engineering B10d 2 x 106 switching cycles Standards VDE 0660 T100, DIN EN 60947-1, IEC 60947-1 VDE 0660 T200, DIN EN 60947-5-1, IEC 60947-5-1 DIN EN ISO 13849-1 EU Conformity acc. to directive 2006/42/EC Approvals DGUV CCSAUS C300 CCC BERNSTEIN AG . Hans-Bernstein-Straße 1 . 32457 Porta Westfalica . www.bernstein.eu Technical modifications and errors excepted. The technical datasheet corresponds to the technical state as of 2016-01-07 and will not be removed in case of changes. Page 2 of 3 6019261018 / 2017-16 Technical Data Notes The safety fixture must always be attached by at least two SHS! See max. load. If the risk assessment of the machine permits a single-channel evaluation, an empty hinge can be used as the support element. If the SHS is used at an ambient temperature of 70 °C, it is possible that the connecting cable will age more rapidly! The connecting cable must be protected against mechanical damage. The cable can be installed in tubes or cable ducts. The electrical connection for a SHS with DGUV inspection certificate is only permitted with the following cable couplings (Bernstein range; cable length: 5 m): 3251103234 (with straight plug) or 3251103236 (with angled plug) The fastening nut of the connecting cable coupling must be in a closed area after assembly that can only be opened with a tool (manipulation guard; e.g. hollow profile, machine stand, frame,...). The manufacturer / supplier of the machine / system is obligated to observe the applicable standards for the size of the safety intervals between the separating safety fixture and the hazard point. These regulations include: EN 294, EN 349, EN 953, EN 1088, ... . The switch may not be used as a stop. For a CSA/UL application it is essential to use CSA/UL approved cable for connection. The suggested protection type (IP code), applies only when at least an equivalent cable coupling is used. BERNSTEIN AG . Hans-Bernstein-Straße 1 . 32457 Porta Westfalica . www.bernstein.eu Technical modifications and errors excepted. The technical datasheet corresponds to the technical state as of 2016-01-07 and will not be removed in case of changes. Page 3 of 3 6019261018 / 2017-16