To put the finishing touch on your
application, we offer an extensive
selection of useful accessories to
build and install DIN Rail terminal
block assemblies and to facilitate
factory and field wiring.
Accessories include end stops, end
plates and partitions. Also offered
are DIN Rails, ferrules, jumpers
and more. From design to commissioning and operation, Altech
accessories help you do the job
better.
We’ve tried to make the selection
of accessories as easy as possible.
The most common accessories are
listed together with their ordering
information on each terminal block
page in this catalog.
Terminal Block
Accessories
66
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Terminal Block Accessories
MOUNTING
DIN Mounting Rails are internationally standardized and available in 35mm, 32mm and 15mm sizes, with or without perforations. These also accommodate a wide variety of control components such as circuit breakers, timers, motor starters, relays,
switches, etc. The 15mm rail with miniature blocks is used
when space is at a premium.
ACCESORIES
Altech accessories add the finishing touches to your terminal
block assemblies. End Stops prevent terminal blocks or other
components and devices from moving laterally on the rail.
End Plates close off the last terminal in a series, a vital function, since sectional terminal blocks are supplied with one side
open. Isolation partitions provide visual separation of terminal
groups, as well as electrical isolation between terminals of different potentials.
INTERCONNECTION
In addition, Altech offers a wide choice of both Internal and
External Jumpers to minimize wiring time and reduce installation cost. Available in standard 2, 3, 4 and 10 pole configurations, or custom multipole jumpers. Our internal jumpers screw
directly into terminal block busbars.
External jumpers are available in straight-comb styles. They
may be used for terminal blocks without internal jumpering provisions or in combination with internal jumpers.
MARKINGTAGS
Marking Tags make DIN Rail assemblies easier to wire
and facilitate troubleshooting. Altech’s extensive terminal block marking system includes standard or custom
printed push on tags in a variety of sizes for circuit
identification.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
67
Altech
TERMINAL BLOCK
ACCESORIES
Shorting Screw
Current Bar
Isolation Partition
Shorting Sleeve
Isolated Internal Jumper
Separator Plate
Internal Jumper
End Plate
DIN 35 mm
Mounting Rail
End Stop
DIN 35-15 mm
Mounting Rail
DIN 32 mm
Mounting Rail
68
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
End Stop
Marking Tag
Sample Terminal Block Assembly
showing all accessories
External Jumper
Support Bracket
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
69
Terminal Block Accessories
DIN35
DIN Mounting Rails
DIN35
Altech DIN Rails comply with DIN
50045, 50022 and 50035 Standards.
DIN Rails have been accepted
throughout the world, allowing the
designer to mount a wide variety of
control components, devices, terminal blocks, etc. on the same rail. The
use of DIN Rails enhances design
capabilities, saves space and reduces
labor.
Standard rails are made of steel with
zinc plating and chromate passivation
and are available in various configurations.
DIN Rails are available in 35mm (7.5
and 15mm deep), 32mm and 15mm
widths and are supplied in 1 m (3'3")
and 2 m (6’6”) lengths. Upon request
they can be cut to custom lengths and
punched with holes or perforations.
35 mm x
7.5 mm deep
Type
Cat. No.
Perforated
Steel
2511120
2511120/1M
2m
1m
Unperforated
Steel
2511110
2511110/1M
2m
1m
35 mm x
15 mm deep
Type
Cat. No.
20
40
Perforated
Steel
CA701-15/S-2M 2m
CA701-15/S
1m
10
20
20
40
Unperforated
Steel
CA701-15-2M
CA701-15
10
20
Length Std. Pk.
18
Length Std. Pk.
2m
1m
18
• 35mm, 32mm, 15mm
• Perforated or unperforated
• Rail material is steel with electrolytic zinc plating
Support Brackets
Support Brackets elevate DIN Rails
away from the panel to facilitate
component mounting and to
increase wiring access. Angled brackets tilt the rail by 35° to improve visibility. Straight brackets are available
in three heights for optimum positioning of the rail.
CA603
M6
Ø7mm (.28in)
M6
18mm
(.71in)
48mm
(1.89in)
H
Ø6mm
(.24 in.)
Slot 6x15mm
(.24x.59 in.)
52m
m(
2.0
5 in
74m
.)
m(
2.9
8 in
.)
60mm (2.36in)
Brackets mount with 2 screws to any
panel or flat surface and have tapped
center holes for rail mounting.
Bracket material is steel, zinc plated
yellow chromated.
70
TSTW
74mm (2.91in)
Suitable for all mounting rails
Cat. No.
Std. Pk.
CA603
25
18mm(.71in.)
Complete with rail mounting hardware:
including one screw & one locknut
Height
Cat. No.
Std. Pk.
1“
2”
3”
CA703
CA803
CA903
25
25
25
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Terminal Block Accessories
DIN32
DIN15
35 mm x
15 mm deep
Type
Cat. No.
Perforated
Steel
2511160
2511160/1M
2m
1m
10
20
Unperforated
Steel
2511150
2511150/1M
2m
1m
10
20
Length Std. Pk.
15 mm x
5.5 mm deep
Type
Cat. No.
Perforated
Steel
CA601/S
Length Std. Pk.
1m
50
18
Mounting Handle
MH2.5
MH4
Mounting handle is used for mounting
10 terminal blocks on a DIN rail, thus
saving consideral time. Specially
designed pins in the mounting handle
grips the terminal blocks when pressed
against entry.
Cat. No.
Jumper for
Std. Pk.
MH2.5
CTS2.5U-N
1
Cat. No.
MH4
Jumper for
Std. Pk.
CTS4U-N
1
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
71
Terminal Block Accessories
End Stops
End Stops prevent terminal
blocks and other DIN Rail mount
components and devices from
moving laterally on the rail.They
are available in polyamide 6.6
and metal configurations for
35mm, 32mm, and 15mm DIN
rails. CA102 and CA202 are large
endstops for heavy duty applications. CA103 is a screwless
endstop and snaps on to the
DIN rail.
Spacer / Separator
CASP is a DIN Rail mountable
spacer generally used for circuit
separation.
DIN Rail
Mounting Foot
CA202
CA102
CA702
CA802
CA602
Material:
Polyamide 6.6
Material:
Polyamide 6.6
Material:
Polyamide 6.6
Material:
Polyamide 6.6
Material:
Polyamide 6.6
Dimensions
H x L x W:
46 x 50 x 9 mm
Dimensions
H x L x W:
44.5 x 50 x 9.5 mm
Dimensions
H x L x W:
34 x 44 x 9 mm
Dimensions
H x L x W:
32 x 45 x 8 mm
Dimensions
H x L x W:
20 x 28 x 8 mm
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
CA102
50
CA202
50
CA702
50
CA802
50
CA602
50
Suitable for:
32 and 35 mm
DIN Rails
Suitable for:
35 mm
DIN Rails
Suitable for:
32 and 35 mm
DIN Rails
Suitable for:
35 mm
DIN Rails
Suitable for:
15 mm
DIN Rails
CA103
CA302
CA402
CA502
CMTB-35 is used to assemble
components on a DIN rail.
Comes with pre-punched holes.
• Support bracket for DIN rail
mounting parts
• Hole Qty x dia., 4x4.3mm,
2x5.5mm
Material:
Polyamide
Material:
Steel
Material:
Steel
Material:
Steel
Dimensions
H x L x W:
41 x 35 x 6 mm
Dimensions
H x L x W:
27 x 39.5 x 16 mm
Dimensions
H x L x W:
27 x 39.5 x 16 mm
Dimensions
H x L x W:
25 x 22.5 x 11.5 mm
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
CA103
50
CA302
50
CA402
50
CA502
50
Suitable for:
35 mm
DIN Rails
Suitable for:
35x7.5mm
DIN Rails
CMTB-35
CASP
Suitable for:
32 mm
DIN Rails
CDL4USP
Material:
Polyamide 6.6
Material:
Polyamide 6.6
Dimensions
H x L x W:
29 x 43 x 8 mm
Dimensions
H x L x W:
18 x 58 x 18 mm
Material:
Polyamide 6.6
Dimensions
H x L x W:
54 x 55.5 x 6 mm
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
Cat. No.
CASP
50
CMTB-35
50
CDL4USP 50
Suitable for:
All
DIN Rails
72
Suitable for:
35x15 mm
DIN Rails
Suitable for:
Mounting Foot for
35 mm DIN rails
Std. Pk.
Suitable for:
All
DIN Rails
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Terminal Block Accessories
Group Identification
GMH6, GMH7 & GMH8
To be mounted directly on Din Rails (GMH6 & GMH7). A
sticker / paper needs to be inserted in the slot which is
covered by a transparent plastic sheet.
Group Marker,
shown imprinted and
attached to CA 702.
Blank and custom
printing available.
Cat. No. MTG1
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
73
Terminal Block Accessories
END PLATES
End Plates
End plates are used to
cover the open side of sectional DIN Rail mount terminal blocks. They should
be used at the end of an
assembly of identical terminal blocks or whenever
there is a change in the
physical size of the terminal
block.
• Material: polyamide 6.6
• Standard color: gray
74
Cat. No.
Std.
Pk.
Dimensions
(H x L x W)
Suitable for:
EP2.5/4UN
EP6/10U
EP25U
EP35
EPCMC1-2
EPCMC2-2
EPCDL4U
EPODL4U
EP1ODL4U
EPCTL2.5U
EPCTL2.5UH
EPCMT4
EPCMB4
EPCSFL4U
EPCSFL6U
EPCAFL4U
EPDDFL4U
EPCDTTU
EPCKT4U
EPCGT4U
EPCTC4U
EPCSTSN5U
EPSTH4
EPSTH4DT
EPCSC2.5T
EPCSC4T
EPCSC6T
EPCSC10T
EPCSC16T
EPCSCP2.5T(L&R)
EPCSC2.5T1-2
EPCSC2.5T2-2
EPCSC4T1-2
EPCSC4T2-2
EPCSC6T1-2
EPAS2.5
EPAS4
EPAS6
EPASF4
EPADL2.5
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
50
50
50
50
50
50
50
50
50
50
50
50
25
50
50
50
50
50
50
50
50
50
50
32 x 39 x 1.5
31 x 42.5 x 1.5
40 x 48 x 2
43 x 50 x 1.5
35.5 x 46.5 x 2.5
40.5 x 65 x 2.5
43 x 55 x 2.4
49 x 68 x 5.5
24 x 68 x 3
55.5 x 84 x 1.5
55.5 x 61 x 1.5
22.5 x 27 x 1.5
27 x 27 x 7
28 x 55.5 x 1.6
42.5 x 36 x 1.5
32 x 72 x 1.5
49 x 87.6 x 3
41 x 63 x 3
30.5 x 46.5 x 2.5
40.5 x 43 x1
34.5 x 47 x 2.5
31 x 50 x 1.5
39.5 x 46 x 1.5
37.5 x 86 x 1.5
23 x 58 x 1.5
28 x 65 x 1.5
32 x 72 x 2
37.5 x 75 x 1.5
82 x 38 x 1.5
27.5 x 35 x 5
27 x 74 x 1.5
25 x 90 x 1.5
28.5 x 84.5 x 1.5
28.5 x 105 x 1.5
94 x 30 x 1.5
35 x 54 x 1.5
27.5 x 61 x 1.5
33.5 x 74 x 1.5
37 x 86 x 1.5
43.5 x 80 x 1.5
CTS2.5UN/4UN/CTT2.5UK/T/J/E
CTS6U/CTS10U
CTS25U
CTS35U
CMC1-2
CMC2-2
CDL4U/CDL4U(I.S)/ CDL4U(E) Series
ODL4U/ODL4UA(Front Side)
ODL4U/ODL4UA(Back Side)
CTL2.5U/2.5UL/2.5U(I.S)
CTL2.5UH/2.5UH(L)/2.5UH(I.S)D2
CMT4/CMT4S/CMT4SU
CMB4
CSFL4U/4U(L)/CSDL4U
CSFL6U/CSDL6U
CAFL4U/4UL/4UN
DDFL4U/4ULR/4U(E)/4U(E)LR
CDTTU/CDTTUSH
CKT4U
CGT4U
CTC4U
CSTSN4U/N5U/N6U/B4U/B5U
STH4
STH4DT / STH4DTSH
CSC2.5T/CSCG2.5T
CSC4T/CSCG4T
CSC6T/CSCG6T
CSC10T/CSCG10T
CSC16T/CSCG16T
CSCP2.5T/CSCP2.5T2
CSC2.5T1-2
CSC2.5T2-2/CSC2.5T/4(E)D3
CSC4T1-2
CSC4T2-2
CSC6T1-2
AS2.5, 2.5/3, 2.5/4, AGT2.5, 2.5/3, 2.5/4
AS4, 4/3, 4/4, AGT4, 4/3, 4/4
AS6, 6/3, AGT6, 6/3
ASF4/ASF4L
ADL2.5/ADL2.5(E)D1/D2
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Terminal Block Accessories
PARTITIONS
Isolation Partitions
Isolation partitions provide
separation between terminal blocks with different
potentials. When used for
DC power applications,
voltages of up to ± 600V DC
can be used on either side
of the isolation partition.
They also provide visual
separation between groups
of blocks.
• Material: polyamide 6.6
• Standard color: gray
Separator Plates
Used for electrical separation of adjacent jumpers.
They can be inserted after
the terminal blocks have
been assembled on DIN
rail. There is no loss of
width.
Cat. No.
Std.
Pk.
Dimensions
(H x L x W)
Suitable for:
PP2.5/4UN
PP6/10U
PP25U
PP25UN
PP35U
PP35UN
PPCMT4
PPCSFL4U
PPCSC2.5T
PPCSC4T
PPCSC6T
50
50
50
50
50
50
50
50
50
50
50
37 x 44 x 1.6
37.5 x 56.5 x 1.5
46.5 x 62 x 1.5
42.5 x 62 x 1
50 x 64.5 x 1.5
50 x 64.5 x 1
32.5 x 37 x 1.6
42.5 x 62 x 1.5
28 x 58.7 x 1.5
33 x 65 x 1.5
36.5 x 72 x 2
CTS2.5UN/4UN/CTT2.5UK/T/J/E
CTS6U/CTS10U
CTS25U
CTS25UN
CTS35U
CTS35UN
CMT4/CMT4S/CMT4SU
CSFL4U/4U(L)/CSDL4U
CSC2.5T/CSCG2.5T
CSC4T/CSCG4T
CSC6T/CSCG6T
SEPARATOR PLATES
Cat. No.
Std.
Pk.
Dimensions
(H x L x W)
Suitable for:
SP2.5/4UN
SP6/10U
SPCDL4U
SPCMB4
100
100
100
100
17.5 x 17.4 x 1.4
15.4 x 16.2 x 1.5
15.4 x 16.2 x 1.6
14.5 x 12 x 1.5
CTS2.5UN/4UN/CTT2.5UK/T/J/E
CTS6U/CTS10U/16U
CDL4U/CDL4U(I.S)/ CDL4U(E) Series
CMB4
Protective Cover /
Side Holding Plates
For protection against dust and
shock, transparent protective
cover can be installed above
the terminal block assembly
with the aid of side/holding
plates. The side holding plates
can be fitted on 35 mm and 32
mm Din rails. These plates
should be backed by standard
end stops.
CTSPC
CSP1
150 mm
Assmebled Block installed
with Protective Cover
For all Rail Mounting Terminals
Mounting Accessories
for CTSPC
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
75
Screw Clamp Terminal Block Accessories
Jumpering System
The jumpering systems bus potentials between terminal blocks, reducing wiring time. Adjacent blocks or
selective terminal blocks within an
assembly can be easily interconnected, leaving terminal clamps free for
wiring. Purchase complete assemblies, which are ready for installation,
or select individual components to
create custom or extra long jumpers.
Jumper ampacity is lower than the
rated current of the respective terminal blocks, therefore, applied current
must not exceed the maximum current value of the block. Internal
jumpers may be used in combination
with external jumpers to achieve
additional jumpering possibilities.
Internal Jumper Assemblies
Internal Jumper Assemblies consist of a
Current Bar, Shorting Sleeves and
screws.They install easily into the center
of the terminal block and connect to the
current bar. They are available as standard 2, 3, 4 or 10 pole assemblies and
are ready for immediate installation.
Insulated internal jumpers provide shock
protection when installed on terminal
block assemblies.
External Jumper
External Jumpers bus potentials
between terminal blocks, reducing
wiring time. Adjacent or selected
blocks within an assembly can be
easily interconnected. Jumper poles
may be removed for selective
jumpering. Jumpers are insulated
and available in 2, 3, 4 and 10 pole
versions.They are made of tin plated
brass/copper.
Current Bars
Current Bars are offered to create
custom jumper assemblies for
increased number of poles or custom
jumpers. Select the current bar with
the required number of poles, or field
cut them to the required length.They
are made of tin or nickel plated copper or brass.
Shorting Sleeves & Screws
Shorting Sleeves & Screws ensure
reliable and mechanically safe electrical connections between current
bars and the terminal block current
bars. One shorting sleeve is required
for each jumpered terminal. They are
made of nickel plated brass.
1 Internal Jumpering System not
available.
2 100 pole strip can be broken down to
any number of poles desired.
76
INTERNAL JUMPER
INSULATED INTERNAL JUMPER
Terminal Series
Poles
Cat. No.
Torque
Std. Pk.
Cat. No.
Torque
Std. Pk.
CTS2.5UN
2
3
4
10
1002
CA721/2
CA721/3
CA721/4
CA721/10
CA721/100
0.4 Nm
100
100
100
10
10
CA741/2
CA741/3
CA741/4
CA741/10
CA741/100
0.4 Nm
100
100
100
10
10
CTS4UN
CMC1-2
CMC2-2
CTS4UTM
CKT4U
2
3
4
10
1002
10 (breakable)
CA722/2
CA722/3
CA722/4
CA722/10
CA722/100
0.4 Nm
100
100
100
10
10
CA742/2
CA742/3
CA742/4
CA742/10
CA742/100
0.4 Nm
100
100
100
10
10
CTS6U
CDTTU1
CDTTU-SH1
CSDL6U1
CSFL6U1
2
3
4
100
CA723/2
CA723/3
CA723/4
CA723/10
0.5 Nm
100
50
50
10
CA743/2
CA743/3
CA743/4
CA743/10
0.5 Nm
100
50
50
10
CTS10U
2
3
4
10
CA724/2
CA724/3
CA724/4
CA724/10
0.5 Nm
100
50
50
10
CA744/2
CA744/3
CA744/4
CA744/10
0.5 Nm
100
50
50
10
CTS16U
2
3
4
10
CA751/2
CA751/3
CA751/4
CA751/10
0.8 Nm
50
50
50
10
CA761/2
CA761/3
CA761/4
CA761/10
0.8 Nm
50
50
50
10
CTS25U
2
3
4
10
CA725/2
CA725/3
CA725/4
CA725/10
0.8 Nm
50
20
20
10
CA745/2
CA745/3
CA745/4
CA745/10
0.8 Nm
50
20
20
10
CTS35U
2
3
4
10
CA726/2
CA726/3
CA726/4
CA726/10
0.8 Nm
50
20
20
10
CA746/2
CA746/3
CA746/4
CA746/10
0.8 Nm
50
20
20
10
CTS35UN*
2
3
4
10
CA771/2
CA771/3
CA771/4
CA771/10
0.8 NM
50
20
20
10
CA781/2
CA781/3
CA781/4
CA781/10
0.8 NM
50
20
20
10
CMT4
CMT4S
CMB4
CDL4U
CDL4U(I.S)
ODL4U
CDL4UTM
2
3
4
10
1002
10 (breakable)
CA727/2
CA727/3
CA727/4
CA727/10
0.4 Nm
100
100
100
10
CA747/2
CA747/3
CA747/4
CA747/10
0.4 Nm
100
100
100
10
DDFL4U
DDFL4U(E)
DDDL4U
CSFL4U1
CSFL4U(L)1
CSDL4U
2
3
4
10
CA729/2
CA729/3
CA729/4
CA729/10
0.5 Nm
100
50
50
10
CA749/2
CA749/3
CA749/4
CA749/10
0.5 Nm
100
50
50
10
CAFL4U
CAFL4U(L)1
2
3
4
10
CTL2.5U
CTL2.5UH
CTL2.5UL
CTL2.5UHL
CTL2.5U(I.S)
2
3
4
10
1002
10 (breakable)
CA722/2
CA722/3
CA722/4
CA722/10
CA722/100
0.4 Nm
100
50
50
20
20
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Screw Clamp Terminal Block Accessories
EXTERNAL JUMPER
CURRENT BAR
Cat. No.
Torque
Std. Pk.
Cat. No.
CA717/2
CA717/3
CA717/4
CA717/10
0.4 Nm
100
100
100
20
CA703/01
CA704/01
CA705/01
CA731/10
CA731/100
CA713/2
CA713/3
CA713/4
CA713/10
0.5 Nm
100
100
100
20
CA710/2
CA710/3
CA710/4
CA710/10
0.8 Nm
CA718/2
CA718/3
CA718/4
CA718/10
0.8 Nm
SHORTING SLEEVE & SCREWS
Std. Pk.
Cat. No.
Torque
Std. Pk.
100
100
100
100
10
CA707/S/Q/01
0.4 Nm
100
CA703/1
CA704/1
CA705/1
CA732/10
CA732/100
100
100
100
10
100
CA707/S/Q/01
0.4 Nm
100
100
50
50
20
CA703/2
CA704/2
CA705/2
CA733/10
100
100
100
100
CA707/S/Q/1
0.5 Nm
100
100
50
50
20
CA703/3
CA704/3
CA705/3
CA734/10
100
100
100
100
CA707/S/Q/1
0.5 Nm
100
CA703/8
CA704/8
CA705/8
CA739/10
100
100
100
100
CA707/S/Q/5
0.8 Nm
100
CA703/4
CA704/4
CA705/4
CA735/10
100
100
100
100
CA707/S/Q/2
0.8 Nm
100
CA703/5
CA704/5
CA705/5
CA736/10
100
100
100
100
CA707/S/Q/2
0.8 Nm
100
CA703/10
CA704/10
CA705/10
CA770/10
100
100
100
100
CA707/S/Q/2
0.8 Nm
100
CA714/2
CA714/3
CA714/4
CA714/10
0.5 Nm
100
100
100
20
CA703/1
CA704/1
CA705/1
CA732/10
CA732/100
CA732/10-A
100
100
100
100
10
100
CA707/S/Q
0.4 Nm
100
CA711/2
CA711/3
CA711/4
CA711/10
0.8 Nm
100
50
50
20
CA703/6
CA704/6
CA705/6
CA737/10
100
100
100
100
CA707/S/Q/3
0.5 Nm
100
CA716/2
CA716/3
CA716/4
CA716/10
0.8 Nm
50
50
50
20
CA715/2
CA715/3
CA715/4
CA715/10
0.4 Nm
100
100
100
20
CA703/1
CA704/1
CA705/1
CA732/10
CA732/100
CA732/10-A
100
100
100
100
10
100
CA707/S/Q/01
0.4 Nm
100
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
77
Spring Clamp Accessories
ALTERNATE JUMPER
Used for jumpering
different size blocks.
78
ADJACENT JUMPER
Terminal
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
Cat. No.
Std. Pk.
CSC2.5T
CSC4T
CSC6T
CSC10T
CSC2.5T1-2
CSC2.5T2-2
CSC4T1-2
CSC4T2-2
CSC6T1-2
CSCP2.5T
CSCP2.5T2
ADL2.5
ASF4
CA801/1-3
CA801/2-3
CA801/3-3
100
100
100
CA901/1
CA901/2
CA901/3
100
100
100
CA801/1-3
CA801/1-3
CA801/2-3
CA801/2-3
CA801/3-3
100
100
100
100
100
CA901/1
CA901/1
CA901/2
CA901/2
CA901/3
100
100
100
100
100
CA801/1-3
100
CA901/1
100
CA801/1
CA801/2
CA801/3
CA801/4
CA801/1
CA801/1
CA801/2
CA801/2
CA801/3
CA803/1
CA803/1
CA801/1
CA801/7
100
100
100
100
100
100
100
100
100
100
100
100
100
For alternate jumpering
Step Down
Jumpers
WIRE TYPE JUMPER
Wire Type Jumper
Terminal
Cat. No.
Std. Pk.
CSC6T –
CSC4T
CA901/4
100
CSC6T –
CSC2.5T
CA901/5
100
CSC4T –
CSC2.5T
CA901/6
100
For adjacent jumpering
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Terminal Block Accessories
BLANK MARKING TAGS
Marking Tags
The cost effective MT
marking system provides
quick and accurate identification.
MT
Push-On
Marking Tags fit all Altech
DIN Rail mount and panel
mount terminal blocks.
They can be inserted individually or as strips of 10
tags on terminal block
assemblies for quick and
easy marking.
MT Marking Tags are supplied blank for custom
marking or they can be
ordered with a horizontal
or vertical imprint. The
standard tag color is white
with black imprint. Tags
can be ordered with up to
3 characters each. Imprints
can be either consecutive
or identical characters. MT
tags, catalog numbers
MT2-MT8 are supplied in
packs of identical strips, 10
tags per strip. Catalog
numbers MT10-MT15 are
supplied in packs of identical strips, 5 tags per strip.
Cat.
No.
Std. Pk.
Strips Tags
MT2
MT3
MT4
MT5
MT6
MT8
MT9
MT9F
MT10
MT12
MT15
MT20
MT25
10
20
10
10
10
10
10
10
20
20
20
20
20
100
100
100
100
100
100
100
10
100
100
100
100
100
Dims
H
W
4.9
5.0
5.0
9.4
9.4
10.4
10.3
10.3
10.4
10.4
10.4
4.9
4.9
5.8
10.0
4.8
4.5
5.5
7.3
8.7
90.0
9.4
11.3
14.3
20
25
HORIZONTAL MARKING TAGS
Cat.
No.
Std. Pk.
Strips Tags
MT2/H
MT3/H
MT4/H
MT5/H
MT6/H
MT8/H
MT9/H
MT9F/H
MT10/H
MT12/H
MT15/H
MT20/H
MT25/H
10
20
10
10
10
10
10
10
20
20
20
20
20
100
100
100
100
100
100
100
10
100
100
100
100
100
Dims
H
W
4.9
5.0
5.0
9.4
9.4
10.4
10.3
10.3
10.4
10.4
10.4
4.9
4.9
5.8
10.0
4.8
4.5
5.5
7.3
8.7
90.0
9.4
11.3
14.3
20
25
Consecutive Digits
(Specify decade)
Nos. 1-10, 11-20, etc. up to 100 *
Nos. 101-110, etc. up to 999 *
Group marker MTG1 is
used for group identification and can be fixed on
the end stop CA702.
VERTICAL MARKING TAGS
Cat.
No.
MT2/V
MT3/V
MT4/V
MT5/V
MT6/V
MT8/V
MT9/V
MT9F/V
MT10/V
MT12/V
MT15/V
MT20/V
MT25/V
Std. Pk.
Strips Tags
10
20
10
10
10
10
10
10
20
20
20
20
20
100
100
100
100
100
100
100
10
100
100
100
100
100
Dims
H
W
4.9
5.0
5.0
9.4
9.4
10.4
10.3
10.3
10.4
10.4
10.4
4.9
4.9
5.8
10.0
4.8
4.5
5.5
7.3
8.7
90.0
9.4
11.3
14.3
20
25
Consecutive Digits
(Specify decade)
Nos. 1-10, 11-20, etc. up to 100
Nos. 101-110, etc. up to 999
Identical Characters
(Specify digits, characters)
Nos. 1, 2, 3 etc. up to 999 *
Characters A, B.up to Z,
Symbols +, -,
When ordering specify
strip marking as a suffix;
i.e. MT2/H-1-10.
Warning Labels
SWL6
These 5 position warning
labels can be mounted on
top of 8 mm Terminal
Blocks. Besides giving
visual identification, it also
makes an entire DIN Rail
Terminal Block assembly
completely shock proof.
SWL6 warning labels are
suitable
for
CTS6U,
CMDB6 and CDB6 series
Terminal Blocks.
*
Group Marker,
shown imprinted and
attached to CA 702.
Blank and custom
printing available.
Cat. No. MTG1
Material:
Polyamide 6.6
Dimensions
H x L x W:
4 x 39.5 x 27 mm
Cat. No.
Std. Pk.
SWL6
50
Suitable for: All DIN Rails
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
79
Marking Systems
80
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Marking Systems
Scriber VS210
TThe VS200 base unit is a stand-alone
plotting system with an integral keyboard
and display screen. The marker fixture,
plotter pen, and the memory cassette
have to be inserted in the base unit to
make it operational. The base unit comes
in an aluminum carrying case and
includes the memory cassette and the
power supply. A manual is available in
English and Spanish.
The VS 200 can be used to produce labels
of all types, with its fixture changeable in
a matter of seconds.
The Vario VS 200 makes labeling easy. The
menu-driven program guides you quickly
and easily through all the steps.
It can be used at any time and in any
place. Easily transported in its special
case, the battery-operated (battery pack
sold separately) VS 200 can be operated
precisely where you need it. The spacious
case provides enough room for the extensive accessories.
SCRIBER VS 210
• Identifiers for connectors, wires, cables and equipment
• Cable ties, shrink tubing, labels and signs of different
sizes and materials, as well as customer-specific items.
• Size: 14.9”x7.5”x1.77”
• Weight: 6.6 lbs.
Ordering Information
BASE UNIT (includes power supply, memory cassette and carrying case) . . . . . . . . . . . . . . . . . . . . .34000000
STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)
and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001
FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxx
MEMORY CASSETTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500001
BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500000
Fixtures &
Memory
Cassette
Battery Pack
CMPS 500 PLOTTER PACKAGE
Plotter Pen,
Ink Cartridge
PLOTTER VP 500
Plotter VP 500
The VP 500 base unit is an auxiliary plotter
and has to be connected to a PC via a parallel port or USB connection. It is a high
speed plotting device and enables plotting
of different markers in one setting. The
marker fixture and the plotter pen have to
be inserted before commencing the plotting operation. The base unit is primarily
controlled through a PC with the help of
Vario Sign software. Manual available in
English and Spanish.
The special design of the VP 500 enables it
to hold different markers from various
manufacturers at the same time. It is also
possible to write on relatively large markers with a maximum height 14 mm.
Fixtures
Fixtures are required for alignment of
markers with respect to the plotter pen.
Different marker fixtures can be mounted
on the plotter bed of the VP 500 at the
same time thereby reducing set up times.
Fixtures for different markers from various
manufacturers like Altech, Allen Bradley,
Connectwell,
ContaClip,
Entrelec,
Weidmuller, Phoenix Contact, PTR,
Wieland, Wago, Murrplastik, Partex, SES
Sterling, etc. are available. For more information on ordering fixtures please contact
Altech.
• CMPS plotter
• Size: 17”x18”x4.9”
• Tag Sizes: MT2, MT3, MT4, MT5, MT6,
MT8, MT9, MT10, MT12, MT15, MT20, MT25
• CMPS software with cable
• 2 fixtures for tags MT5-MT15
(MT9 sold separately)
• 1 fixture for tags MT2 and MT25
• 2 disposable pens
• Identifiers for connectors, wires, cables
and equipment
• Cable ties, shrink tubing, labels and signs
of different sizes and materials, as well as
customer-specific items.
• Size: 26”x18”x4.9”
Ordering Information
CMPS 500 PLOTTER PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34130008
VP 500 BASE UNIT (includes cable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000030
STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)
and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001
VARIO SIGN SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000020
SERVICE KIT (includes 4 seal bonnets and 10 priming print cards) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000026
FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxx *
* See page 85.
Fixtures
Plotter Pen,
Ink Cartridge
Vario Sign
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
81
Marking Systems
Engraver VE500
ENGRAVER VE500
The engraving unit was specifically
designed to be used with the VP500 amd
CMPS 500 plotters. Changing back and
forth between the pen-plotter and the
engraver is easy. The engraver is meant
to engrave plastic signs on double sided
material, pre-cut or blank sheets, for legend plates, push button inlays, etc. The
engraver is programmed by the VarioSign
software for ease of use and design flexibility.
Ordering Information
VE500 ENGRAVER UNIT (VP500 REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000040
Engraving Needles
These engraving needles are to be used
with the VE500 engraver. They have a 15°
angle and are available in 6 tip widths or
as a complete set.
ENGRAVING NEEDLE
Vacuum Cleaner Bag
Replacement bags for
engraver’s vacuum cleaner
the
VE500
Ordering Information
Product
Width
Engraving Needle
0.20mm
Engraving Needle
0.30mm
Engraving Needle
0.40mm
Engraving Needle
0.50mm
Engraving Needle
0.70mm
Engraving Needle
1.00mm
Engraving Set(0.20, 0.30, 0.40, 0.50, 0.70, 1.00mm)
Engraving Needle(0.20 mm cutter stainless steel)
Order No.
35010003
35010002
35010001
35010000
35010004
35010005
35010006
35012033
VACUUM CLEANER BAG
Ordering Information
VACUUM CLEANER BAG, SET OF 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35020000
82
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Marking Systems Accessories
Plotter Pens
These “tubular-nib” pens are suitable for Vario
Scriber VS 200, Vario Plotter VP 500 and all current labeling and identification systems with
HP penholders. They are available in six tip
widths identified by body color - 0.18 mm, 0.25
mm, 0.35 mm, 0.50 mm, 0.70 mm, and 1.00 mm;
ink cartridge not supplied with pen. Special
variants for other systems are available on
request. Specially designed pre-filled felt-tip
pens are available in a set of 4 colors (black,
blue, red and green) and 2 sizes - 0.3 and 0.7
mm.
Ink Cartridges
These are easy to insert “tubular-nib” pen cartridges containing special black ink suitable for
marking, identifying and labeling various plastics. It is fast drying, smudge-proof, fade resistant, and resistant to chemicals when used on
suitable plastic materials.
Disposable Pens
The disposable pens use the same special ink
as used in the ink cartridges. They deliver the
same outstanding durability and print quality as
the standard plotter pens with the convenience
of a disposable pen. These pre-filled pens
allow for fast, efficient and cost effective printing without refilling ink or cleaning. They are
available in two tip widths, 0.25 mm and 0.35
mm.
Hand Pens
The hand pens use the same special ink, as
used in cartridges, and delivers the same outstanding durability and print quality. They are
used for additional identification and special
labeling tasks and are available in four tip
widths of 0.25mm, 0.35mm, 0.50 mm, and 0.70
mm. No ink included. Must order part 35100006.
Product
“tubular-nib” pens,
6 sizes for black ink
EK
EK
EK
EK
EK
EK
Plotter
Plotter
Plotter
Plotter
Plotter
Plotter
Pen
Pen
Pen
Pen
Pen
Pen
Width
Order No.
0.18 mm
0.25 mm
0.35 mm
0.50 mm
0.70 mm
1.00 mm
35001018
35001025
35001035
35001050
35001070
35001100
EK Ink Cartridge
(5 pieces, Black, 1 ml. each)
35100006
EK Felt-tip Pen-Set (white tip)
EK Felt-tip Pen-Set (yellow tip)
0.30 mm
0.70 mm
35000005
35000010
EK Disposable Plotter Pen
EK Disposable Plotter Pen
0.25 mm
0.35 mm
35003025
35003035
EK
EK
EK
EK
0.25
0.35
0.50
0.70
35002025
35002035
35002050
35002070
felt-tip pens,
2 sizes, 4 colors
Hand
Hand
Hand
Hand
Pen
Pen
Pen
Pen
mm
mm
mm
mm
Cleaning Unit
It is an easy-to-use cleaning unit developed
specially for EK Pens. The cleaning unit
enables the pens to be rinsed thoroughly while
preventing skin contact with cleaning fluid or
ink. The cleaning unit can be used for up to ten
cleaning cycles. The necessary precautions
must be taken when disposing of cleaning fluid,
the cleaning unit can be reused.
EK Cleaning Unit (empty)
35100009
Pen Cleaner
This cleaning solution comes in easy to handle
cartridges and is used in conjunction with the
cleaning unit. A standard pack consists of two
pen cleaner cartridges. Cleaning can be performed on standard refillable pens only.
EK Pen Cleaner (2 pieces, 2x10 ml.)
EK Cleaning Set
(includes cleaning unit and pen cleaner)
35100008
35100010
Adapter for an Utra Fine Sharpie™
35000501
Adapter
This adapter allows the user of Sharpie™ Ultra
Fine felt tip pens instead of standard plotter
pens.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
83
Marking Systems Accessories
Plotter Pen Handling and Care
Handling and care of the EK-Team plotter pens for the universal EK-Team marking system.
For the state of the art universal marking system by EK-team, the manufacture is supplying a fast drying and etching ink that is
required for marking plastic material within the control and automation industry. Due to these special properties of the ink, these
plotter pens require much more care than a regular marking pen. Therefore EK-Team designed some helpful tools to keep your EK-team
plotter pen in tip top shape.
1
Recovery and Storage Stand
Refillable
Pens
Disposable
Pen
This stand is designed to keep the plotter pen in an
upright position, when not used with the marking
system.
The upright position allows the plotter pen to recover
and to be properly stored. It is recommended to
store plotter pens that will be idle for a few hours in a
dry and cool location, preferably in the refrigerator.
Refrigerate pens when
not in use for long
periods of time.
Pen Stand
The recovery and storage stand accommodates easy
storage and handling.
Call Altech for your free recovery and storage stand.
Cat. No. 35000100
2
The "suction ball" is a helpful tool to bring a slightly clogged
disposable or refillable plotter pen back to life.
Suction Ball
The suction can unclog a slightly clogged plotter pen from the
vacuum created within the "ball".
This additional tool can be very helpful in addition to the already
available cleaning kit (Cat. No. 35100010) for the refillable plotter
pens.
5 replacement tips are included with each suction ball.
3
Cat. No. 35100013
Pen Cleaning
CLEANING UNIT
It is an easy-to-use cleaning unit developed specially for refillable pens. The cleaning unit enables
the pens to be rinsed thoroughly while preventing skin contact with cleaning fluid or ink. The
cleaning unit can be used for up to ten cleaning cycles. The necessary precautions must be taken
when disposing of cleaning fluid, the cleaning unit can be reused.
PEN CLEANER
This cleaning solution comes in easy to handle cartridges and is used in conjunction with the
cleaning unit. A standard pack consists of two pen cleaner cartridges. Cleaning can be performed
on standard refillable pens only.
Cleaning Set Cat. No. 35100010
84
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Marking Systems VP500 and CMPS 500 Fixtures
Description
Altech
Altech MT 2n - MT 4n, MT 7.5, MT 20, MT 25
Altech MT 5 - MT 15
Altech Group marker G1, G2, G4
ABB / Entrelec
ABB Entrelec universal - RC/RCT quarter size
ABB Entrelec RC 510A, 610A, 810A
ABB Entrelec RC 510B, 610B, 810B”
ABB Entrelec RB-RBP 5-12
ABB Entrelec BA 5-50
ABB Entrelec PIB
ABB Entrelec RCCV
ABB Entrelec BS / ILS / ILS-H
Set of sticky pads ( 8 pcs) for RC/RCT
Allen Bradley / Woertz
Allen Bradley Universal W4 SERIES OLD AB WORTZ & S.S.
Weidmüller / Rockwell (Allen Bradley)
Weidmüller MultiCard Universal (M5X8)
Weidmüller MultiCard SF4-6
Set of sticky pads (6 pcs) for Multicard Universal
Conta Clip
SB5, SB6 BSTR10.12
SB8/10
Phoenix
Phoenix Contact ZBM
Phoenix Contact ZB
Phoenix Contact ZBFM
Phoenix Contact ZBF, ZBN
Phoenix Contact BNZ
Phoenix Contact BN-ZB
Phoenix Contact SS-ZB
Phoenix Contact LBHZ
Phoenix Contact PAB
Phoenix Contact GPE
Phoenix Contact GPE
Wago
WAGO WMB 4/4,2/5
WAGO WSB 4
WAGO WSB 5/5,2
WAGO WSB mini
WAGO Group marker carrier
WAGO Marking Strip
WAGO Marker tags
WAGO WTB
WAGO WCB
WAGO WMB inline
WAGO 210-345
Set of sticky pads (12 pcs) for Top Job (Marking Strip)
Weidmüller / Rockwell (Allen Bradley)
Weidmüller MultiCard Universal
Weidmüller MultiCard SF4-6
Set of sticky pads (6 pcs) for Multicard Universal
Wieland
Wieland Universal
Wieland BZ/WKF 1,5 04.243.2053.0
Wieland BZ/WKF 1,5/10 Z4.243.2053.0
Wieland Steierform 6 x 15, 10 x 20
Part No.
34902081
34902001
34902080
34902063
34902114
34902102
34902086
34902100
34902101
34902038
34902106
34910000
34902046
34902045
34902044
34910001
34902002
34902003
34902039
34902047
34902049
34900050
34902051
34902052
34902053
34902054
34902055
34902071
34902106
34902041
34902074
34902075
34902076
34902078
34902087
34902094
34902096
34902097
34902098
34902106
34910002
34902045
34902044
34910001
34902043
34902047
34902049
34902106
VE500 and CMPS 500 Engraving Fixtures
EK-TEAM
Universal engraving and plot support plate half size (A4)
Universal engraving and plot support plate full size (A3)
Universal engraving and plot support plate 30x100 ninefold
Universal engraving and plot support plate 60x100 fourfold
Universal engraving and plot support plate 90x100 threefold
34902106
34902107
34902115
34902116
34902117
CUSTOM FIXTURES AND OTHER MANUFACTURERES ARE AVAILABLE
Contact Altech for Pricing (not in Price Book)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
85
PCB Mounting Tracks
Narrow Mounting Track
Extrusion and Components
Mount standard or custom printed circuit
boards in Mounting Tracks which can be
conveniently DIN rail or panel mounted in
your control panel or cabinet. These are the
same tracks used for Altech interface modules. We now make them available to you to
house and protect your custom boards, etc.
Tracks are easily cut to size or can be
ordered precut to specific lengths. They are
easily assembled from standard components
and snap onto 35mm DIN rail or can be panel
mounted.
For PC Board Widths 73mm (2.9 in.)
W
EPS
L
Each track has two sets of printed circuit
board guides to accept two alternate board
widths.
End Sections hold printed circuit boards
securely in place and keep out foreign
objects.
EPDR1
MTGF1
Panel
Mount
MOUNTING
When mounting extrusions on DIN rail, order
two or more DIN Rail mounting feet. These
feet slide into grooves on the extrusion. Then
attach two DIN Rail Mount End Sections
with help of EPS screws.
Cat. No.
To panel mount, order two Panel Mount End
Sections (and EPS screws), each with an
integral mounting flange with a 6 x 8mm (.24
x .32 in.) hole slot.
Mounting Track
1 meter, grey
2 meter, grey
1 meter, green*
2 meter, green*
If desired, tracks can be direct mounted
using double sided tape. Order two DIN rail
mount end sections (and EPS screws).
Accessories
• Standard Lengths: 1m (3'-3") or 2m (6'-6")
• Track Material: PVC
• Temperature Limit:
Short Term - 80˚C (176˚F)
Continuous - 70˚C (158˚F)
• End Section, Foot Material: Polyamide
• Preassembled, Precut Lengths Available
• Tracks Accept Standard MT2 Marking Tags
MTGTK1
MTGTK1/1M
MTGTK1
MTGTK1/1M/G
MTGTK1/G
DIN Rail
Mount
Std. Pk.
5
5
5
5
DIN Rail Mount End Section, grey
DIN Rail Mount End Section, green*
EPDR1
EPDR1/G
100
100
DIN Rail Mounting Foot, grey
DIN Rail Mounting Foot, green*
MTGF1
MTGF1/G
100
100
Panel Mount End Section, grey
Panel Mount End Section, green*
EPDP1
EPDP1/G
100
100
DIN Rail / Panel Mount End Section
Screws #4x1/2”, Phillips Pan head
(2 required per end section)
EPS
200
Marking Tags
MT2
100
DIN Rail Mounting Kit
(2x EPDR, 2x MTGF, 4x EPS)
1.100
1
Sizing Information
Printed Circuit Board Width
Track Type
* Green color available on request.
Contact Altech for more information.
86
MTGTK1
MTGTK2
High Guide (HG)
73 ± 1mm (2.9 ± 0.05 in.)
110 ± 1mm (4.3 ± 0.05 in.)
Mounting Track Extrusion
"Cut-to-Size" Formula
Extrusion Length = Printed Circuit
Board Length – 4.5mm (.175 in.)
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
PCB Mounting Tracks
Wide Mounting Track
Extrusion and Components
Narrow Mounting Track
For PC Board Widths 110mm (4.9 in.)
W
MTGTK2
73
2
16
EPS
L
11.4
69
84
PCB MOUNTINGTRACK (73 mm)
MTGF1
15
EPDP2
DIN Rail
Mount
15
35
82
DIN RAIL MOUNTING FOOT (73mm)
Wide Mounting Track
Panel
Mount
Cat. No.
110
Std. Pk.
5
5
5
5
11.4
MTGTK2/1M
MTGTK2
MTGTK2/1M/G
MTGTK2/G
16
2
119
EPDR2
EPDR2/G
100
100
MTGF2
MTGF2/G
100
100
EPDP2
EPDP2/G
100
100
EPS
200
MT2
100
15
PCB MOUNTINGTRACK (110 mm)
15
35
117
DIN RAIL MOUNTING FOOT (110mm)
aAlso applies for DIN Rail Mount Unit
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
87
Receptacles
PANEL MOUNT
WALL MOUNT
36.5 x 61.5 x 50
50 x 71 x 53.5
58.5 x 84 x 53.5
10 mm
10 mm
10 mm
Insulation Material
Thermoplastic
Thermoplastic
Thermoplastic
Type of Connection
3 screw clamps
3 screw clamps
3 screw clamps
E154664
E154664
E154664
Voltage Rating
125 V
125 V
125 V
Current Rating
15 A
15 A
15 A
Features:
• DIN Rail, Panel Mount
or Wall Mount
• Rating: 15A/125V AC
• Finger Protection: IP54
• Available in 3 colors.
External Dimension (HxWxL mm)
Stripping Length
Approvals*
Cat. No.
Std. Pk.
DIN RAIL MOUNT
Cat. No.
Std. Pk.
Cat. No.
PMRBU
PMRGR
PMRBA
1
1
1
WMRBU
WMRGR
WMRBA
1
1
1
DMRBU
DMRGR
DMRBA
SEALGASK
1
SEALGASK
1
SEALGASK
Std. Pk.
Complete Kit:
Blue
Gray
Black
Optional Accessory
Sealing Gasket
1
1
1
1
aAlso applies for DIN Rail Mount Unit
88
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
Receptacles
PANEL MOUNT
1
Wiring of
Receptacles
WALL MOUNT
1
DIN RAIL MOUNT
1
1 Optional Sealing Gasket for wet environments.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
89
工商网监
湘ICP备2023018690号
