EP6/10U/BU

To put the finishing touch on your application, we offer an extensive selection of useful accessories to build and install DIN Rail terminal block assemblies and to facilitate factory and field wiring. Accessories include end stops, end plates and partitions. Also offered are DIN Rails, ferrules, jumpers and more. From design to commissioning and operation, Altech accessories help you do the job better. We’ve tried to make the selection of accessories as easy as possible. The most common accessories are listed together with their ordering information on each terminal block page in this catalog. Terminal Block Accessories 66 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Terminal Block Accessories MOUNTING DIN Mounting Rails are internationally standardized and available in 35mm, 32mm and 15mm sizes, with or without perforations. These also accommodate a wide variety of control components such as circuit breakers, timers, motor starters, relays, switches, etc. The 15mm rail with miniature blocks is used when space is at a premium. ACCESORIES Altech accessories add the finishing touches to your terminal block assemblies. End Stops prevent terminal blocks or other components and devices from moving laterally on the rail. End Plates close off the last terminal in a series, a vital function, since sectional terminal blocks are supplied with one side open. Isolation partitions provide visual separation of terminal groups, as well as electrical isolation between terminals of different potentials. INTERCONNECTION In addition, Altech offers a wide choice of both Internal and External Jumpers to minimize wiring time and reduce installation cost. Available in standard 2, 3, 4 and 10 pole configurations, or custom multipole jumpers. Our internal jumpers screw directly into terminal block busbars. External jumpers are available in straight-comb styles. They may be used for terminal blocks without internal jumpering provisions or in combination with internal jumpers. MARKINGTAGS Marking Tags make DIN Rail assemblies easier to wire and facilitate troubleshooting. Altech’s extensive terminal block marking system includes standard or custom printed push on tags in a variety of sizes for circuit identification. Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 67 Altech TERMINAL BLOCK ACCESORIES Shorting Screw Current Bar Isolation Partition Shorting Sleeve Isolated Internal Jumper Separator Plate Internal Jumper End Plate DIN 35 mm Mounting Rail End Stop DIN 35-15 mm Mounting Rail DIN 32 mm Mounting Rail 68 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com End Stop Marking Tag Sample Terminal Block Assembly showing all accessories External Jumper Support Bracket Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 69 Terminal Block Accessories DIN35 DIN Mounting Rails DIN35 Altech DIN Rails comply with DIN 50045, 50022 and 50035 Standards. DIN Rails have been accepted throughout the world, allowing the designer to mount a wide variety of control components, devices, terminal blocks, etc. on the same rail. The use of DIN Rails enhances design capabilities, saves space and reduces labor. Standard rails are made of steel with zinc plating and chromate passivation and are available in various configurations. DIN Rails are available in 35mm (7.5 and 15mm deep), 32mm and 15mm widths and are supplied in 1 m (3'3") and 2 m (6’6”) lengths. Upon request they can be cut to custom lengths and punched with holes or perforations. 35 mm x 7.5 mm deep Type Cat. No. Perforated Steel 2511120 2511120/1M 2m 1m Unperforated Steel 2511110 2511110/1M 2m 1m 35 mm x 15 mm deep Type Cat. No. 20 40 Perforated Steel CA701-15/S-2M 2m CA701-15/S 1m 10 20 20 40 Unperforated Steel CA701-15-2M CA701-15 10 20 Length Std. Pk. 18 Length Std. Pk. 2m 1m 18 • 35mm, 32mm, 15mm • Perforated or unperforated • Rail material is steel with electrolytic zinc plating Support Brackets Support Brackets elevate DIN Rails away from the panel to facilitate component mounting and to increase wiring access. Angled brackets tilt the rail by 35° to improve visibility. Straight brackets are available in three heights for optimum positioning of the rail. CA603 M6 Ø7mm (.28in) M6 18mm (.71in) 48mm (1.89in) H Ø6mm (.24 in.) Slot 6x15mm (.24x.59 in.) 52m m( 2.0 5 in 74m .) m( 2.9 8 in .) 60mm (2.36in) Brackets mount with 2 screws to any panel or flat surface and have tapped center holes for rail mounting. Bracket material is steel, zinc plated yellow chromated. 70 TSTW 74mm (2.91in) Suitable for all mounting rails Cat. No. Std. Pk. CA603 25 18mm(.71in.) Complete with rail mounting hardware: including one screw & one locknut Height Cat. No. Std. Pk. 1“ 2” 3” CA703 CA803 CA903 25 25 25 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Terminal Block Accessories DIN32 DIN15 35 mm x 15 mm deep Type Cat. No. Perforated Steel 2511160 2511160/1M 2m 1m 10 20 Unperforated Steel 2511150 2511150/1M 2m 1m 10 20 Length Std. Pk. 15 mm x 5.5 mm deep Type Cat. No. Perforated Steel CA601/S Length Std. Pk. 1m 50 18 Mounting Handle MH2.5 MH4 Mounting handle is used for mounting 10 terminal blocks on a DIN rail, thus saving consideral time. Specially designed pins in the mounting handle grips the terminal blocks when pressed against entry. Cat. No. Jumper for Std. Pk. MH2.5 CTS2.5U-N 1 Cat. No. MH4 Jumper for Std. Pk. CTS4U-N 1 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 71 Terminal Block Accessories End Stops End Stops prevent terminal blocks and other DIN Rail mount components and devices from moving laterally on the rail.They are available in polyamide 6.6 and metal configurations for 35mm, 32mm, and 15mm DIN rails. CA102 and CA202 are large endstops for heavy duty applications. CA103 is a screwless endstop and snaps on to the DIN rail. Spacer / Separator CASP is a DIN Rail mountable spacer generally used for circuit separation. DIN Rail Mounting Foot CA202 CA102 CA702 CA802 CA602 Material: Polyamide 6.6 Material: Polyamide 6.6 Material: Polyamide 6.6 Material: Polyamide 6.6 Material: Polyamide 6.6 Dimensions H x L x W: 46 x 50 x 9 mm Dimensions H x L x W: 44.5 x 50 x 9.5 mm Dimensions H x L x W: 34 x 44 x 9 mm Dimensions H x L x W: 32 x 45 x 8 mm Dimensions H x L x W: 20 x 28 x 8 mm Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. CA102 50 CA202 50 CA702 50 CA802 50 CA602 50 Suitable for: 32 and 35 mm DIN Rails Suitable for: 35 mm DIN Rails Suitable for: 32 and 35 mm DIN Rails Suitable for: 35 mm DIN Rails Suitable for: 15 mm DIN Rails CA103 CA302 CA402 CA502 CMTB-35 is used to assemble components on a DIN rail. Comes with pre-punched holes. • Support bracket for DIN rail mounting parts • Hole Qty x dia., 4x4.3mm, 2x5.5mm Material: Polyamide Material: Steel Material: Steel Material: Steel Dimensions H x L x W: 41 x 35 x 6 mm Dimensions H x L x W: 27 x 39.5 x 16 mm Dimensions H x L x W: 27 x 39.5 x 16 mm Dimensions H x L x W: 25 x 22.5 x 11.5 mm Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. CA103 50 CA302 50 CA402 50 CA502 50 Suitable for: 35 mm DIN Rails Suitable for: 35x7.5mm DIN Rails CMTB-35 CASP Suitable for: 32 mm DIN Rails CDL4USP Material: Polyamide 6.6 Material: Polyamide 6.6 Dimensions H x L x W: 29 x 43 x 8 mm Dimensions H x L x W: 18 x 58 x 18 mm Material: Polyamide 6.6 Dimensions H x L x W: 54 x 55.5 x 6 mm Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. CASP 50 CMTB-35 50 CDL4USP 50 Suitable for: All DIN Rails 72 Suitable for: 35x15 mm DIN Rails Suitable for: Mounting Foot for 35 mm DIN rails Std. Pk. Suitable for: All DIN Rails Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Terminal Block Accessories Group Identification GMH6, GMH7 & GMH8 To be mounted directly on Din Rails (GMH6 & GMH7). A sticker / paper needs to be inserted in the slot which is covered by a transparent plastic sheet. Group Marker, shown imprinted and attached to CA 702. Blank and custom printing available. Cat. No. MTG1 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 73 Terminal Block Accessories END PLATES End Plates End plates are used to cover the open side of sectional DIN Rail mount terminal blocks. They should be used at the end of an assembly of identical terminal blocks or whenever there is a change in the physical size of the terminal block. • Material: polyamide 6.6 • Standard color: gray 74 Cat. No. Std. Pk. Dimensions (H x L x W) Suitable for: EP2.5/4UN EP6/10U EP25U EP35 EPCMC1-2 EPCMC2-2 EPCDL4U EPODL4U EP1ODL4U EPCTL2.5U EPCTL2.5UH EPCMT4 EPCMB4 EPCSFL4U EPCSFL6U EPCAFL4U EPDDFL4U EPCDTTU EPCKT4U EPCGT4U EPCTC4U EPCSTSN5U EPSTH4 EPSTH4DT EPCSC2.5T EPCSC4T EPCSC6T EPCSC10T EPCSC16T EPCSCP2.5T(L&R) EPCSC2.5T1-2 EPCSC2.5T2-2 EPCSC4T1-2 EPCSC4T2-2 EPCSC6T1-2 EPAS2.5 EPAS4 EPAS6 EPASF4 EPADL2.5 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 25 25 50 50 50 50 50 50 50 50 50 50 50 50 25 50 50 50 50 50 50 50 50 50 50 32 x 39 x 1.5 31 x 42.5 x 1.5 40 x 48 x 2 43 x 50 x 1.5 35.5 x 46.5 x 2.5 40.5 x 65 x 2.5 43 x 55 x 2.4 49 x 68 x 5.5 24 x 68 x 3 55.5 x 84 x 1.5 55.5 x 61 x 1.5 22.5 x 27 x 1.5 27 x 27 x 7 28 x 55.5 x 1.6 42.5 x 36 x 1.5 32 x 72 x 1.5 49 x 87.6 x 3 41 x 63 x 3 30.5 x 46.5 x 2.5 40.5 x 43 x1 34.5 x 47 x 2.5 31 x 50 x 1.5 39.5 x 46 x 1.5 37.5 x 86 x 1.5 23 x 58 x 1.5 28 x 65 x 1.5 32 x 72 x 2 37.5 x 75 x 1.5 82 x 38 x 1.5 27.5 x 35 x 5 27 x 74 x 1.5 25 x 90 x 1.5 28.5 x 84.5 x 1.5 28.5 x 105 x 1.5 94 x 30 x 1.5 35 x 54 x 1.5 27.5 x 61 x 1.5 33.5 x 74 x 1.5 37 x 86 x 1.5 43.5 x 80 x 1.5 CTS2.5UN/4UN/CTT2.5UK/T/J/E CTS6U/CTS10U CTS25U CTS35U CMC1-2 CMC2-2 CDL4U/CDL4U(I.S)/ CDL4U(E) Series ODL4U/ODL4UA(Front Side) ODL4U/ODL4UA(Back Side) CTL2.5U/2.5UL/2.5U(I.S) CTL2.5UH/2.5UH(L)/2.5UH(I.S)D2 CMT4/CMT4S/CMT4SU CMB4 CSFL4U/4U(L)/CSDL4U CSFL6U/CSDL6U CAFL4U/4UL/4UN DDFL4U/4ULR/4U(E)/4U(E)LR CDTTU/CDTTUSH CKT4U CGT4U CTC4U CSTSN4U/N5U/N6U/B4U/B5U STH4 STH4DT / STH4DTSH CSC2.5T/CSCG2.5T CSC4T/CSCG4T CSC6T/CSCG6T CSC10T/CSCG10T CSC16T/CSCG16T CSCP2.5T/CSCP2.5T2 CSC2.5T1-2 CSC2.5T2-2/CSC2.5T/4(E)D3 CSC4T1-2 CSC4T2-2 CSC6T1-2 AS2.5, 2.5/3, 2.5/4, AGT2.5, 2.5/3, 2.5/4 AS4, 4/3, 4/4, AGT4, 4/3, 4/4 AS6, 6/3, AGT6, 6/3 ASF4/ASF4L ADL2.5/ADL2.5(E)D1/D2 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Terminal Block Accessories PARTITIONS Isolation Partitions Isolation partitions provide separation between terminal blocks with different potentials. When used for DC power applications, voltages of up to ± 600V DC can be used on either side of the isolation partition. They also provide visual separation between groups of blocks. • Material: polyamide 6.6 • Standard color: gray Separator Plates Used for electrical separation of adjacent jumpers. They can be inserted after the terminal blocks have been assembled on DIN rail. There is no loss of width. Cat. No. Std. Pk. Dimensions (H x L x W) Suitable for: PP2.5/4UN PP6/10U PP25U PP25UN PP35U PP35UN PPCMT4 PPCSFL4U PPCSC2.5T PPCSC4T PPCSC6T 50 50 50 50 50 50 50 50 50 50 50 37 x 44 x 1.6 37.5 x 56.5 x 1.5 46.5 x 62 x 1.5 42.5 x 62 x 1 50 x 64.5 x 1.5 50 x 64.5 x 1 32.5 x 37 x 1.6 42.5 x 62 x 1.5 28 x 58.7 x 1.5 33 x 65 x 1.5 36.5 x 72 x 2 CTS2.5UN/4UN/CTT2.5UK/T/J/E CTS6U/CTS10U CTS25U CTS25UN CTS35U CTS35UN CMT4/CMT4S/CMT4SU CSFL4U/4U(L)/CSDL4U CSC2.5T/CSCG2.5T CSC4T/CSCG4T CSC6T/CSCG6T SEPARATOR PLATES Cat. No. Std. Pk. Dimensions (H x L x W) Suitable for: SP2.5/4UN SP6/10U SPCDL4U SPCMB4 100 100 100 100 17.5 x 17.4 x 1.4 15.4 x 16.2 x 1.5 15.4 x 16.2 x 1.6 14.5 x 12 x 1.5 CTS2.5UN/4UN/CTT2.5UK/T/J/E CTS6U/CTS10U/16U CDL4U/CDL4U(I.S)/ CDL4U(E) Series CMB4 Protective Cover / Side Holding Plates For protection against dust and shock, transparent protective cover can be installed above the terminal block assembly with the aid of side/holding plates. The side holding plates can be fitted on 35 mm and 32 mm Din rails. These plates should be backed by standard end stops. CTSPC CSP1 150 mm Assmebled Block installed with Protective Cover For all Rail Mounting Terminals Mounting Accessories for CTSPC Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 75 Screw Clamp Terminal Block Accessories Jumpering System The jumpering systems bus potentials between terminal blocks, reducing wiring time. Adjacent blocks or selective terminal blocks within an assembly can be easily interconnected, leaving terminal clamps free for wiring. Purchase complete assemblies, which are ready for installation, or select individual components to create custom or extra long jumpers. Jumper ampacity is lower than the rated current of the respective terminal blocks, therefore, applied current must not exceed the maximum current value of the block. Internal jumpers may be used in combination with external jumpers to achieve additional jumpering possibilities. Internal Jumper Assemblies Internal Jumper Assemblies consist of a Current Bar, Shorting Sleeves and screws.They install easily into the center of the terminal block and connect to the current bar. They are available as standard 2, 3, 4 or 10 pole assemblies and are ready for immediate installation. Insulated internal jumpers provide shock protection when installed on terminal block assemblies. External Jumper External Jumpers bus potentials between terminal blocks, reducing wiring time. Adjacent or selected blocks within an assembly can be easily interconnected. Jumper poles may be removed for selective jumpering. Jumpers are insulated and available in 2, 3, 4 and 10 pole versions.They are made of tin plated brass/copper. Current Bars Current Bars are offered to create custom jumper assemblies for increased number of poles or custom jumpers. Select the current bar with the required number of poles, or field cut them to the required length.They are made of tin or nickel plated copper or brass. Shorting Sleeves & Screws Shorting Sleeves & Screws ensure reliable and mechanically safe electrical connections between current bars and the terminal block current bars. One shorting sleeve is required for each jumpered terminal. They are made of nickel plated brass. 1 Internal Jumpering System not available. 2 100 pole strip can be broken down to any number of poles desired. 76 INTERNAL JUMPER INSULATED INTERNAL JUMPER Terminal Series Poles Cat. No. Torque Std. Pk. Cat. No. Torque Std. Pk. CTS2.5UN 2 3 4 10 1002 CA721/2 CA721/3 CA721/4 CA721/10 CA721/100 0.4 Nm 100 100 100 10 10 CA741/2 CA741/3 CA741/4 CA741/10 CA741/100 0.4 Nm 100 100 100 10 10 CTS4UN CMC1-2 CMC2-2 CTS4UTM CKT4U 2 3 4 10 1002 10 (breakable) CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 0.4 Nm 100 100 100 10 10 CA742/2 CA742/3 CA742/4 CA742/10 CA742/100 0.4 Nm 100 100 100 10 10 CTS6U CDTTU1 CDTTU-SH1 CSDL6U1 CSFL6U1 2 3 4 100 CA723/2 CA723/3 CA723/4 CA723/10 0.5 Nm 100 50 50 10 CA743/2 CA743/3 CA743/4 CA743/10 0.5 Nm 100 50 50 10 CTS10U 2 3 4 10 CA724/2 CA724/3 CA724/4 CA724/10 0.5 Nm 100 50 50 10 CA744/2 CA744/3 CA744/4 CA744/10 0.5 Nm 100 50 50 10 CTS16U 2 3 4 10 CA751/2 CA751/3 CA751/4 CA751/10 0.8 Nm 50 50 50 10 CA761/2 CA761/3 CA761/4 CA761/10 0.8 Nm 50 50 50 10 CTS25U 2 3 4 10 CA725/2 CA725/3 CA725/4 CA725/10 0.8 Nm 50 20 20 10 CA745/2 CA745/3 CA745/4 CA745/10 0.8 Nm 50 20 20 10 CTS35U 2 3 4 10 CA726/2 CA726/3 CA726/4 CA726/10 0.8 Nm 50 20 20 10 CA746/2 CA746/3 CA746/4 CA746/10 0.8 Nm 50 20 20 10 CTS35UN* 2 3 4 10 CA771/2 CA771/3 CA771/4 CA771/10 0.8 NM 50 20 20 10 CA781/2 CA781/3 CA781/4 CA781/10 0.8 NM 50 20 20 10 CMT4 CMT4S CMB4 CDL4U CDL4U(I.S) ODL4U CDL4UTM 2 3 4 10 1002 10 (breakable) CA727/2 CA727/3 CA727/4 CA727/10 0.4 Nm 100 100 100 10 CA747/2 CA747/3 CA747/4 CA747/10 0.4 Nm 100 100 100 10 DDFL4U DDFL4U(E) DDDL4U CSFL4U1 CSFL4U(L)1 CSDL4U 2 3 4 10 CA729/2 CA729/3 CA729/4 CA729/10 0.5 Nm 100 50 50 10 CA749/2 CA749/3 CA749/4 CA749/10 0.5 Nm 100 50 50 10 CAFL4U CAFL4U(L)1 2 3 4 10 CTL2.5U CTL2.5UH CTL2.5UL CTL2.5UHL CTL2.5U(I.S) 2 3 4 10 1002 10 (breakable) CA722/2 CA722/3 CA722/4 CA722/10 CA722/100 0.4 Nm 100 50 50 20 20 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Screw Clamp Terminal Block Accessories EXTERNAL JUMPER CURRENT BAR Cat. No. Torque Std. Pk. Cat. No. CA717/2 CA717/3 CA717/4 CA717/10 0.4 Nm 100 100 100 20 CA703/01 CA704/01 CA705/01 CA731/10 CA731/100 CA713/2 CA713/3 CA713/4 CA713/10 0.5 Nm 100 100 100 20 CA710/2 CA710/3 CA710/4 CA710/10 0.8 Nm CA718/2 CA718/3 CA718/4 CA718/10 0.8 Nm SHORTING SLEEVE & SCREWS Std. Pk. Cat. No. Torque Std. Pk. 100 100 100 100 10 CA707/S/Q/01 0.4 Nm 100 CA703/1 CA704/1 CA705/1 CA732/10 CA732/100 100 100 100 10 100 CA707/S/Q/01 0.4 Nm 100 100 50 50 20 CA703/2 CA704/2 CA705/2 CA733/10 100 100 100 100 CA707/S/Q/1 0.5 Nm 100 100 50 50 20 CA703/3 CA704/3 CA705/3 CA734/10 100 100 100 100 CA707/S/Q/1 0.5 Nm 100 CA703/8 CA704/8 CA705/8 CA739/10 100 100 100 100 CA707/S/Q/5 0.8 Nm 100 CA703/4 CA704/4 CA705/4 CA735/10 100 100 100 100 CA707/S/Q/2 0.8 Nm 100 CA703/5 CA704/5 CA705/5 CA736/10 100 100 100 100 CA707/S/Q/2 0.8 Nm 100 CA703/10 CA704/10 CA705/10 CA770/10 100 100 100 100 CA707/S/Q/2 0.8 Nm 100 CA714/2 CA714/3 CA714/4 CA714/10 0.5 Nm 100 100 100 20 CA703/1 CA704/1 CA705/1 CA732/10 CA732/100 CA732/10-A 100 100 100 100 10 100 CA707/S/Q 0.4 Nm 100 CA711/2 CA711/3 CA711/4 CA711/10 0.8 Nm 100 50 50 20 CA703/6 CA704/6 CA705/6 CA737/10 100 100 100 100 CA707/S/Q/3 0.5 Nm 100 CA716/2 CA716/3 CA716/4 CA716/10 0.8 Nm 50 50 50 20 CA715/2 CA715/3 CA715/4 CA715/10 0.4 Nm 100 100 100 20 CA703/1 CA704/1 CA705/1 CA732/10 CA732/100 CA732/10-A 100 100 100 100 10 100 CA707/S/Q/01 0.4 Nm 100 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 77 Spring Clamp Accessories ALTERNATE JUMPER Used for jumpering different size blocks. 78 ADJACENT JUMPER Terminal Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. CSC2.5T CSC4T CSC6T CSC10T CSC2.5T1-2 CSC2.5T2-2 CSC4T1-2 CSC4T2-2 CSC6T1-2 CSCP2.5T CSCP2.5T2 ADL2.5 ASF4 CA801/1-3 CA801/2-3 CA801/3-3 100 100 100 CA901/1 CA901/2 CA901/3 100 100 100 CA801/1-3 CA801/1-3 CA801/2-3 CA801/2-3 CA801/3-3 100 100 100 100 100 CA901/1 CA901/1 CA901/2 CA901/2 CA901/3 100 100 100 100 100 CA801/1-3 100 CA901/1 100 CA801/1 CA801/2 CA801/3 CA801/4 CA801/1 CA801/1 CA801/2 CA801/2 CA801/3 CA803/1 CA803/1 CA801/1 CA801/7 100 100 100 100 100 100 100 100 100 100 100 100 100 For alternate jumpering Step Down Jumpers WIRE TYPE JUMPER Wire Type Jumper Terminal Cat. No. Std. Pk. CSC6T – CSC4T CA901/4 100 CSC6T – CSC2.5T CA901/5 100 CSC4T – CSC2.5T CA901/6 100 For adjacent jumpering Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Terminal Block Accessories BLANK MARKING TAGS Marking Tags The cost effective MT marking system provides quick and accurate identification. MT Push-On Marking Tags fit all Altech DIN Rail mount and panel mount terminal blocks. They can be inserted individually or as strips of 10 tags on terminal block assemblies for quick and easy marking. MT Marking Tags are supplied blank for custom marking or they can be ordered with a horizontal or vertical imprint. The standard tag color is white with black imprint. Tags can be ordered with up to 3 characters each. Imprints can be either consecutive or identical characters. MT tags, catalog numbers MT2-MT8 are supplied in packs of identical strips, 10 tags per strip. Catalog numbers MT10-MT15 are supplied in packs of identical strips, 5 tags per strip. Cat. No. Std. Pk. Strips Tags MT2 MT3 MT4 MT5 MT6 MT8 MT9 MT9F MT10 MT12 MT15 MT20 MT25 10 20 10 10 10 10 10 10 20 20 20 20 20 100 100 100 100 100 100 100 10 100 100 100 100 100 Dims H W 4.9 5.0 5.0 9.4 9.4 10.4 10.3 10.3 10.4 10.4 10.4 4.9 4.9 5.8 10.0 4.8 4.5 5.5 7.3 8.7 90.0 9.4 11.3 14.3 20 25 HORIZONTAL MARKING TAGS Cat. No. Std. Pk. Strips Tags MT2/H MT3/H MT4/H MT5/H MT6/H MT8/H MT9/H MT9F/H MT10/H MT12/H MT15/H MT20/H MT25/H 10 20 10 10 10 10 10 10 20 20 20 20 20 100 100 100 100 100 100 100 10 100 100 100 100 100 Dims H W 4.9 5.0 5.0 9.4 9.4 10.4 10.3 10.3 10.4 10.4 10.4 4.9 4.9 5.8 10.0 4.8 4.5 5.5 7.3 8.7 90.0 9.4 11.3 14.3 20 25 Consecutive Digits (Specify decade) Nos. 1-10, 11-20, etc. up to 100 * Nos. 101-110, etc. up to 999 * Group marker MTG1 is used for group identification and can be fixed on the end stop CA702. VERTICAL MARKING TAGS Cat. No. MT2/V MT3/V MT4/V MT5/V MT6/V MT8/V MT9/V MT9F/V MT10/V MT12/V MT15/V MT20/V MT25/V Std. Pk. Strips Tags 10 20 10 10 10 10 10 10 20 20 20 20 20 100 100 100 100 100 100 100 10 100 100 100 100 100 Dims H W 4.9 5.0 5.0 9.4 9.4 10.4 10.3 10.3 10.4 10.4 10.4 4.9 4.9 5.8 10.0 4.8 4.5 5.5 7.3 8.7 90.0 9.4 11.3 14.3 20 25 Consecutive Digits (Specify decade) Nos. 1-10, 11-20, etc. up to 100 Nos. 101-110, etc. up to 999 Identical Characters (Specify digits, characters) Nos. 1, 2, 3 etc. up to 999 * Characters A, B.up to Z, Symbols +, -, When ordering specify strip marking as a suffix; i.e. MT2/H-1-10. Warning Labels SWL6 These 5 position warning labels can be mounted on top of 8 mm Terminal Blocks. Besides giving visual identification, it also makes an entire DIN Rail Terminal Block assembly completely shock proof. SWL6 warning labels are suitable for CTS6U, CMDB6 and CDB6 series Terminal Blocks. * Group Marker, shown imprinted and attached to CA 702. Blank and custom printing available. Cat. No. MTG1 Material: Polyamide 6.6 Dimensions H x L x W: 4 x 39.5 x 27 mm Cat. No. Std. Pk. SWL6 50 Suitable for: All DIN Rails Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 79 Marking Systems 80 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Marking Systems Scriber VS210 TThe VS200 base unit is a stand-alone plotting system with an integral keyboard and display screen. The marker fixture, plotter pen, and the memory cassette have to be inserted in the base unit to make it operational. The base unit comes in an aluminum carrying case and includes the memory cassette and the power supply. A manual is available in English and Spanish. The VS 200 can be used to produce labels of all types, with its fixture changeable in a matter of seconds. The Vario VS 200 makes labeling easy. The menu-driven program guides you quickly and easily through all the steps. It can be used at any time and in any place. Easily transported in its special case, the battery-operated (battery pack sold separately) VS 200 can be operated precisely where you need it. The spacious case provides enough room for the extensive accessories. SCRIBER VS 210 • Identifiers for connectors, wires, cables and equipment • Cable ties, shrink tubing, labels and signs of different sizes and materials, as well as customer-specific items. • Size: 14.9”x7.5”x1.77” • Weight: 6.6 lbs. Ordering Information BASE UNIT (includes power supply, memory cassette and carrying case) . . . . . . . . . . . . . . . . . . . . .34000000 STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen) and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001 FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxx MEMORY CASSETTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500001 BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500000 Fixtures & Memory Cassette Battery Pack CMPS 500 PLOTTER PACKAGE Plotter Pen, Ink Cartridge PLOTTER VP 500 Plotter VP 500 The VP 500 base unit is an auxiliary plotter and has to be connected to a PC via a parallel port or USB connection. It is a high speed plotting device and enables plotting of different markers in one setting. The marker fixture and the plotter pen have to be inserted before commencing the plotting operation. The base unit is primarily controlled through a PC with the help of Vario Sign software. Manual available in English and Spanish. The special design of the VP 500 enables it to hold different markers from various manufacturers at the same time. It is also possible to write on relatively large markers with a maximum height 14 mm. Fixtures Fixtures are required for alignment of markers with respect to the plotter pen. Different marker fixtures can be mounted on the plotter bed of the VP 500 at the same time thereby reducing set up times. Fixtures for different markers from various manufacturers like Altech, Allen Bradley, Connectwell, ContaClip, Entrelec, Weidmuller, Phoenix Contact, PTR, Wieland, Wago, Murrplastik, Partex, SES Sterling, etc. are available. For more information on ordering fixtures please contact Altech. • CMPS plotter • Size: 17”x18”x4.9” • Tag Sizes: MT2, MT3, MT4, MT5, MT6, MT8, MT9, MT10, MT12, MT15, MT20, MT25 • CMPS software with cable • 2 fixtures for tags MT5-MT15 (MT9 sold separately) • 1 fixture for tags MT2 and MT25 • 2 disposable pens • Identifiers for connectors, wires, cables and equipment • Cable ties, shrink tubing, labels and signs of different sizes and materials, as well as customer-specific items. • Size: 26”x18”x4.9” Ordering Information CMPS 500 PLOTTER PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34130008 VP 500 BASE UNIT (includes cable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000030 STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen) and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001 VARIO SIGN SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000020 SERVICE KIT (includes 4 seal bonnets and 10 priming print cards) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000026 FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxx * * See page 85. Fixtures Plotter Pen, Ink Cartridge Vario Sign Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 81 Marking Systems Engraver VE500 ENGRAVER VE500 The engraving unit was specifically designed to be used with the VP500 amd CMPS 500 plotters. Changing back and forth between the pen-plotter and the engraver is easy. The engraver is meant to engrave plastic signs on double sided material, pre-cut or blank sheets, for legend plates, push button inlays, etc. The engraver is programmed by the VarioSign software for ease of use and design flexibility. Ordering Information VE500 ENGRAVER UNIT (VP500 REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000040 Engraving Needles These engraving needles are to be used with the VE500 engraver. They have a 15° angle and are available in 6 tip widths or as a complete set. ENGRAVING NEEDLE Vacuum Cleaner Bag Replacement bags for engraver’s vacuum cleaner the VE500 Ordering Information Product Width Engraving Needle 0.20mm Engraving Needle 0.30mm Engraving Needle 0.40mm Engraving Needle 0.50mm Engraving Needle 0.70mm Engraving Needle 1.00mm Engraving Set(0.20, 0.30, 0.40, 0.50, 0.70, 1.00mm) Engraving Needle(0.20 mm cutter stainless steel) Order No. 35010003 35010002 35010001 35010000 35010004 35010005 35010006 35012033 VACUUM CLEANER BAG Ordering Information VACUUM CLEANER BAG, SET OF 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35020000 82 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Marking Systems Accessories Plotter Pens These “tubular-nib” pens are suitable for Vario Scriber VS 200, Vario Plotter VP 500 and all current labeling and identification systems with HP penholders. They are available in six tip widths identified by body color - 0.18 mm, 0.25 mm, 0.35 mm, 0.50 mm, 0.70 mm, and 1.00 mm; ink cartridge not supplied with pen. Special variants for other systems are available on request. Specially designed pre-filled felt-tip pens are available in a set of 4 colors (black, blue, red and green) and 2 sizes - 0.3 and 0.7 mm. Ink Cartridges These are easy to insert “tubular-nib” pen cartridges containing special black ink suitable for marking, identifying and labeling various plastics. It is fast drying, smudge-proof, fade resistant, and resistant to chemicals when used on suitable plastic materials. Disposable Pens The disposable pens use the same special ink as used in the ink cartridges. They deliver the same outstanding durability and print quality as the standard plotter pens with the convenience of a disposable pen. These pre-filled pens allow for fast, efficient and cost effective printing without refilling ink or cleaning. They are available in two tip widths, 0.25 mm and 0.35 mm. Hand Pens The hand pens use the same special ink, as used in cartridges, and delivers the same outstanding durability and print quality. They are used for additional identification and special labeling tasks and are available in four tip widths of 0.25mm, 0.35mm, 0.50 mm, and 0.70 mm. No ink included. Must order part 35100006. Product “tubular-nib” pens, 6 sizes for black ink EK EK EK EK EK EK Plotter Plotter Plotter Plotter Plotter Plotter Pen Pen Pen Pen Pen Pen Width Order No. 0.18 mm 0.25 mm 0.35 mm 0.50 mm 0.70 mm 1.00 mm 35001018 35001025 35001035 35001050 35001070 35001100 EK Ink Cartridge (5 pieces, Black, 1 ml. each) 35100006 EK Felt-tip Pen-Set (white tip) EK Felt-tip Pen-Set (yellow tip) 0.30 mm 0.70 mm 35000005 35000010 EK Disposable Plotter Pen EK Disposable Plotter Pen 0.25 mm 0.35 mm 35003025 35003035 EK EK EK EK 0.25 0.35 0.50 0.70 35002025 35002035 35002050 35002070 felt-tip pens, 2 sizes, 4 colors Hand Hand Hand Hand Pen Pen Pen Pen mm mm mm mm Cleaning Unit It is an easy-to-use cleaning unit developed specially for EK Pens. The cleaning unit enables the pens to be rinsed thoroughly while preventing skin contact with cleaning fluid or ink. The cleaning unit can be used for up to ten cleaning cycles. The necessary precautions must be taken when disposing of cleaning fluid, the cleaning unit can be reused. EK Cleaning Unit (empty) 35100009 Pen Cleaner This cleaning solution comes in easy to handle cartridges and is used in conjunction with the cleaning unit. A standard pack consists of two pen cleaner cartridges. Cleaning can be performed on standard refillable pens only. EK Pen Cleaner (2 pieces, 2x10 ml.) EK Cleaning Set (includes cleaning unit and pen cleaner) 35100008 35100010 Adapter for an Utra Fine Sharpie™ 35000501 Adapter This adapter allows the user of Sharpie™ Ultra Fine felt tip pens instead of standard plotter pens. Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 83 Marking Systems Accessories Plotter Pen Handling and Care Handling and care of the EK-Team plotter pens for the universal EK-Team marking system. For the state of the art universal marking system by EK-team, the manufacture is supplying a fast drying and etching ink that is required for marking plastic material within the control and automation industry. Due to these special properties of the ink, these plotter pens require much more care than a regular marking pen. Therefore EK-Team designed some helpful tools to keep your EK-team plotter pen in tip top shape. 1 Recovery and Storage Stand Refillable Pens Disposable Pen This stand is designed to keep the plotter pen in an upright position, when not used with the marking system. The upright position allows the plotter pen to recover and to be properly stored. It is recommended to store plotter pens that will be idle for a few hours in a dry and cool location, preferably in the refrigerator. Refrigerate pens when not in use for long periods of time. Pen Stand The recovery and storage stand accommodates easy storage and handling. Call Altech for your free recovery and storage stand. Cat. No. 35000100 2 The "suction ball" is a helpful tool to bring a slightly clogged disposable or refillable plotter pen back to life. Suction Ball The suction can unclog a slightly clogged plotter pen from the vacuum created within the "ball". This additional tool can be very helpful in addition to the already available cleaning kit (Cat. No. 35100010) for the refillable plotter pens. 5 replacement tips are included with each suction ball. 3 Cat. No. 35100013 Pen Cleaning CLEANING UNIT It is an easy-to-use cleaning unit developed specially for refillable pens. The cleaning unit enables the pens to be rinsed thoroughly while preventing skin contact with cleaning fluid or ink. The cleaning unit can be used for up to ten cleaning cycles. The necessary precautions must be taken when disposing of cleaning fluid, the cleaning unit can be reused. PEN CLEANER This cleaning solution comes in easy to handle cartridges and is used in conjunction with the cleaning unit. A standard pack consists of two pen cleaner cartridges. Cleaning can be performed on standard refillable pens only. Cleaning Set Cat. No. 35100010 84 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Marking Systems VP500 and CMPS 500 Fixtures Description Altech Altech MT 2n - MT 4n, MT 7.5, MT 20, MT 25 Altech MT 5 - MT 15 Altech Group marker G1, G2, G4 ABB / Entrelec ABB Entrelec universal - RC/RCT quarter size ABB Entrelec RC 510A, 610A, 810A ABB Entrelec RC 510B, 610B, 810B” ABB Entrelec RB-RBP 5-12 ABB Entrelec BA 5-50 ABB Entrelec PIB ABB Entrelec RCCV ABB Entrelec BS / ILS / ILS-H Set of sticky pads ( 8 pcs) for RC/RCT Allen Bradley / Woertz Allen Bradley Universal W4 SERIES OLD AB WORTZ & S.S. Weidmüller / Rockwell (Allen Bradley) Weidmüller MultiCard Universal (M5X8) Weidmüller MultiCard SF4-6 Set of sticky pads (6 pcs) for Multicard Universal Conta Clip SB5, SB6 BSTR10.12 SB8/10 Phoenix Phoenix Contact ZBM Phoenix Contact ZB Phoenix Contact ZBFM Phoenix Contact ZBF, ZBN Phoenix Contact BNZ Phoenix Contact BN-ZB Phoenix Contact SS-ZB Phoenix Contact LBHZ Phoenix Contact PAB Phoenix Contact GPE Phoenix Contact GPE Wago WAGO WMB 4/4,2/5 WAGO WSB 4 WAGO WSB 5/5,2 WAGO WSB mini WAGO Group marker carrier WAGO Marking Strip WAGO Marker tags WAGO WTB WAGO WCB WAGO WMB inline WAGO 210-345 Set of sticky pads (12 pcs) for Top Job (Marking Strip) Weidmüller / Rockwell (Allen Bradley) Weidmüller MultiCard Universal Weidmüller MultiCard SF4-6 Set of sticky pads (6 pcs) for Multicard Universal Wieland Wieland Universal Wieland BZ/WKF 1,5 04.243.2053.0 Wieland BZ/WKF 1,5/10 Z4.243.2053.0 Wieland Steierform 6 x 15, 10 x 20 Part No. 34902081 34902001 34902080 34902063 34902114 34902102 34902086 34902100 34902101 34902038 34902106 34910000 34902046 34902045 34902044 34910001 34902002 34902003 34902039 34902047 34902049 34900050 34902051 34902052 34902053 34902054 34902055 34902071 34902106 34902041 34902074 34902075 34902076 34902078 34902087 34902094 34902096 34902097 34902098 34902106 34910002 34902045 34902044 34910001 34902043 34902047 34902049 34902106 VE500 and CMPS 500 Engraving Fixtures EK-TEAM Universal engraving and plot support plate half size (A4) Universal engraving and plot support plate full size (A3) Universal engraving and plot support plate 30x100 ninefold Universal engraving and plot support plate 60x100 fourfold Universal engraving and plot support plate 90x100 threefold 34902106 34902107 34902115 34902116 34902117 CUSTOM FIXTURES AND OTHER MANUFACTURERES ARE AVAILABLE Contact Altech for Pricing (not in Price Book) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 85 PCB Mounting Tracks Narrow Mounting Track Extrusion and Components Mount standard or custom printed circuit boards in Mounting Tracks which can be conveniently DIN rail or panel mounted in your control panel or cabinet. These are the same tracks used for Altech interface modules. We now make them available to you to house and protect your custom boards, etc. Tracks are easily cut to size or can be ordered precut to specific lengths. They are easily assembled from standard components and snap onto 35mm DIN rail or can be panel mounted. For PC Board Widths 73mm (2.9 in.) W EPS L Each track has two sets of printed circuit board guides to accept two alternate board widths. End Sections hold printed circuit boards securely in place and keep out foreign objects. EPDR1 MTGF1 Panel Mount MOUNTING When mounting extrusions on DIN rail, order two or more DIN Rail mounting feet. These feet slide into grooves on the extrusion. Then attach two DIN Rail Mount End Sections with help of EPS screws. Cat. No. To panel mount, order two Panel Mount End Sections (and EPS screws), each with an integral mounting flange with a 6 x 8mm (.24 x .32 in.) hole slot. Mounting Track 1 meter, grey 2 meter, grey 1 meter, green* 2 meter, green* If desired, tracks can be direct mounted using double sided tape. Order two DIN rail mount end sections (and EPS screws). Accessories • Standard Lengths: 1m (3'-3") or 2m (6'-6") • Track Material: PVC • Temperature Limit: Short Term - 80˚C (176˚F) Continuous - 70˚C (158˚F) • End Section, Foot Material: Polyamide • Preassembled, Precut Lengths Available • Tracks Accept Standard MT2 Marking Tags MTGTK1 MTGTK1/1M MTGTK1 MTGTK1/1M/G MTGTK1/G DIN Rail Mount Std. Pk. 5 5 5 5 DIN Rail Mount End Section, grey DIN Rail Mount End Section, green* EPDR1 EPDR1/G 100 100 DIN Rail Mounting Foot, grey DIN Rail Mounting Foot, green* MTGF1 MTGF1/G 100 100 Panel Mount End Section, grey Panel Mount End Section, green* EPDP1 EPDP1/G 100 100 DIN Rail / Panel Mount End Section Screws #4x1/2”, Phillips Pan head (2 required per end section) EPS 200 Marking Tags MT2 100 DIN Rail Mounting Kit (2x EPDR, 2x MTGF, 4x EPS) 1.100 1 Sizing Information Printed Circuit Board Width Track Type * Green color available on request. Contact Altech for more information. 86 MTGTK1 MTGTK2 High Guide (HG) 73 ± 1mm (2.9 ± 0.05 in.) 110 ± 1mm (4.3 ± 0.05 in.) Mounting Track Extrusion "Cut-to-Size" Formula Extrusion Length = Printed Circuit Board Length – 4.5mm (.175 in.) Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com PCB Mounting Tracks Wide Mounting Track Extrusion and Components Narrow Mounting Track For PC Board Widths 110mm (4.9 in.) W MTGTK2 73 2 16 EPS L 11.4 69 84 PCB MOUNTINGTRACK (73 mm) MTGF1 15 EPDP2 DIN Rail Mount 15 35 82 DIN RAIL MOUNTING FOOT (73mm) Wide Mounting Track Panel Mount Cat. No. 110 Std. Pk. 5 5 5 5 11.4 MTGTK2/1M MTGTK2 MTGTK2/1M/G MTGTK2/G 16 2 119 EPDR2 EPDR2/G 100 100 MTGF2 MTGF2/G 100 100 EPDP2 EPDP2/G 100 100 EPS 200 MT2 100 15 PCB MOUNTINGTRACK (110 mm) 15 35 117 DIN RAIL MOUNTING FOOT (110mm) aAlso applies for DIN Rail Mount Unit Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 87 Receptacles PANEL MOUNT WALL MOUNT 36.5 x 61.5 x 50 50 x 71 x 53.5 58.5 x 84 x 53.5 10 mm 10 mm 10 mm Insulation Material Thermoplastic Thermoplastic Thermoplastic Type of Connection 3 screw clamps 3 screw clamps 3 screw clamps E154664 E154664 E154664 Voltage Rating 125 V 125 V 125 V Current Rating 15 A 15 A 15 A Features: • DIN Rail, Panel Mount or Wall Mount • Rating: 15A/125V AC • Finger Protection: IP54 • Available in 3 colors. External Dimension (HxWxL mm) Stripping Length Approvals* Cat. No. Std. Pk. DIN RAIL MOUNT Cat. No. Std. Pk. Cat. No. PMRBU PMRGR PMRBA 1 1 1 WMRBU WMRGR WMRBA 1 1 1 DMRBU DMRGR DMRBA SEALGASK 1 SEALGASK 1 SEALGASK Std. Pk. Complete Kit: Blue Gray Black Optional Accessory Sealing Gasket 1 1 1 1 aAlso applies for DIN Rail Mount Unit 88 Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com Receptacles PANEL MOUNT 1 Wiring of Receptacles WALL MOUNT 1 DIN RAIL MOUNT 1 1 Optional Sealing Gasket for wet environments. Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 89