S19235

P RODUC T BRIEF 56 92 S1 S19256 10 G Ethernet / Fibre Channel / SONET / SDH Dual CDR (2km - 30km) Features • • • • • • • • • • • • • • • • • • • • • • • • • • Complies with XFP MSA Specifications 25 mUIpp Jitter Generation TX Equalizer to Mitigate Data Dependent Jitter Low Power 540 mW Dual CDR - 9.95 to 11.32 Gbps operation Footprint compatible to the EDC based 10G Dual CDR S19233 CDR Power Down Option Ideal - 300 mW (with TX EQ and RX EQ) LOS Function - Compliant to GR-253 RSSI Function (8 mV to 800 mV) Squelch Control (LOS or LOL conditions) Squelch Output Polarity Control Polarity Invert Control on Output Buffers Lock detect indication Automatic Threshold Adjust (Maximizes Sensitivity) External threshold & Phase Adjust Through I2C Bus® Superior Crosstalk Isolation Loopback (Optical and Electrical interface) AGC embedded equalizer TX and RX Integrated equalizer that support over 24” FR4 on Transmitter Electrical Side TX Output Buffer Slew Rate Control Lock detect indication -40 to 85°C operation CMOS 0.13 Micron Technology 1.8 and 3.3 Volt Power Supply 6x6 mm2 PBGA package with 0.8 mm pitch ESD - 1500 V, 500 V High Speed Inputs Description The S19256 is a fully integrated low power dual CDR device suitable for short reach module applications. It is used in 10GbE / 10GFC / OC192 SONET/SDH PMD modules, such as the XFP MSA modules. Integrated in this device on the receive optical side, an AGC amplifier with offset cancellation circuitry, and CDR. On the transmit electrical side the S19256 also has an equalization circuit, and CDR that reshapes the data after up to 24" of transmission over copper on FR-4 PWB material, with low jitter generation of 25 mUI. For SFP+ applications, this device allows both CDR’s to be powered-down and bypassed while using only the equalization circuitry needed to mitigate Data Dependent Jitter caused by the interconnect. The low-jitter CML interface guarantees compliance with the bit error rate requirements of the Telcordia and ITU-T standards. The S19256 is packaged in a 6x6 mm2 PBGA, offering designers a small package outline. Value Proposition - Design multiple XFP modules ranging from 2 km to 120 km link with one footprint. The S19256 (no EDC) is pin compatible to the EDC based 10G Dual CDR S19233. S19256: 2 km-30 km; S19233: 2 km-120 km Overview The S19256 can be used to implement the front end of SONET/SDH/FEC/10GbE/FC/G.709 equipment which consists primarily of the serial transmit interface and the serial receive interface. The system timing circuitry consists of a high-speed phase detector, clock and data recovery unit and equalization circuitry. The device utilizes on-chip clock recovery PLL components that allow the use of a slower external clock reference, 155.52 MHz (or equivalent FEC/10GbE/10 Gbps FC rate), in support of existing system clocking schemes. On the transmitter side, an equalizer is integrated in the receive front end to reshape the data after transmission over FR-4. This enables low bit error rate and transmission over longer trace length. The low-jitter, 1-bit, CML interfaces guarantee compliance with the bit-error rate requirements of the Telcordia and ITU-T standards. The 10 Gbps serial electrical interface specifications are compliant with the XFI as specified in the XFP MSA module specification. The high speed serial input and output can be connected to the AMCC SerDes (S19235 or S19237) across 60 cm (24”) of improved FR-4 material or across 40 cm of standard FR-4 with one connector. Applications • • • • • • 10G Fibre Channel and Ethernet Designs 10GbE with FEC 10G SONET/SDH/FEC Designs SONET/SDH Test Equipment SONET/SDH/FEC DWDM Equipment XFP MSA Modules (2 km, 10 km, and 40 km) TOSA AMCC S19235/ 37 XFI AMCC S19256 Dual CDR XFP Module ROSA OC-192/ 10GE /10FC 10 Gbps Line Card System Block Diagram with the S19256 SPECIFIC AT IONS S19256 AMCC Suggested Interface Devices S19235 SFI-4 Phase 1 SONET/SDH STS-192/10 Gig Ethernet CMOS Transceiver with ISI Compensation S19237 SFI-4 Phase 1 SONET/SDH STS-192/10 Gig Ethernet CMOS Transceiver with ISI Compensation Transmitter Side Operations • • • • • • • • • • • • • • • 1-bit serial data input Equalization to compensate for FR-4 Threshold and Offset cancellation adjust Clock and Data recovery Data retime Serial data output Serial input with AGC (Equalization) 30 mVpp Differential Sensitivity with threshold adjust Loss of signal detection Clock and Data recovery Serial data output Optical and Electrical Loopbacks Power Down CDR Squelch Polarity Invert Receiver Side Operations Common Operations 6290 Sequence Dr. San Diego, CA 92121 P 858 450 9333 F 858 450 9885 www.amcc.com For technical support, please call 1-800-840-6055 or 858-535-6517, or email support@amcc.com. AMCC reserves the right to make changes to its products, its datasheets, or related documentation, without notice and warrants its products solely pursuant to its terms and conditions of sale, only to substantially comply with the latest available datasheet. Please consult AMCC’s Term and Conditions of Sale for its warranties and other terms, conditions and limitations. AMCC may discontinue any semiconductor product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information is current. AMCC does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. AMCC reserves the right to ship devices of higher grade in place of those of lower grade. AMCC SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. AMCC is a registered trademark of Applied Micro Circuits Corporation. PowerPC and the PowerPC logo are registered trademarks of IBM Corporation. All other trademarks are the property of their respective holders. Copyright © 2006 Applied Micro Circuits Corporation. All Rights Reserved. S19256_PB2018_v1.01_20061103