AM29LV320DT90REI

Am29LV320D Data Sheet RETIRED PRODUCT This product has been retired and is not available for designs. For new and current designs, S29AL032D supersedes Am29LV320D and is the factory-recommended migration path. Please refer to the S29AL032D datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only. April 2005 The following document specifies Spansion memory products that are now offered by both Advanced Micro Devices and Fujitsu. Although the document is marked with the name of the company that originally developed the specification, these products will be offered to customers of both AMD and Fujitsu. Continuity of Specifications There is no change to this datasheet as a result of offering the device as a Spansion product. Any changes that have been made are the result of normal datasheet improvement and are noted in the document revision summary, where supported. Future routine revisions will occur when appropriate, and changes will be noted in a revision summary. For More Information Please contact your local AMD or Fujitsu sales office for additional information about Spansion memory solutions. Publication Number 23579 Revision C Amendment 8 Issue Date December 14, 2005 THIS PAGE LEFT INTENTIONALLY BLANK. Am29LV320D 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Boot Sector Flash Memory This product has been retired and is not available for designs. For new and current designs, S29AL032D supersedes Am29LV320D and is the factory-recommended migration path. Please refer to the S29AL032D datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only. DISTINCTIVE CHARACTERISTICS ARCHITECTURAL ADVANTAGES Secured Silicon — 64 Kbyte Sector Size; Replacement/substitute devices (such as Mirrorbit™) have 256 bytes. — Factory locked and identifiable: 16 bytes (8 words) available for secure, random factory Electronic Serial Number; verifiable as factory locked through autoselect function. ExpressFlash option allows entire sector to be available for factory-secured data — Customer lockable: Can be programmed once and then permanently locked after being shipped from AMD Zero Power Operation — Sophisticated power management circuits reduce power consumed during inactive periods to nearly zero. Package options — 48-pin TSOP — 48-ball FBGA Sector Architecture — Eight 8 Kbyte sectors — Sixty-three 64 Kbyte sectors Top or bottom boot block Manufactured on 0.23 µm process technology Compatible with JEDEC standards — Pinout and software compatible with single-power-supply flash standard PERFORMANCE CHARACTERISTICS High performance — Access time as fast 90 ns — Program time: 7µs/word typical utilizing Accelerate function Ultra low power consumption (typical values) — 2 mA active read current at 1 MHz — 10 mA active read current at 5 MHz — 200 nA in standby or automatic sleep mode Minimum 1 million erase cycles guaranteed per sector 20 Year data retention at 125°C — Reliable operation for the life of the system SOFTWARE FEATURES Supports Common Flash Memory Interface (CFI) Erase Suspend/Erase Resume — Suspends erase operations to allow programming in non-suspended sectors Data# Polling and Toggle Bits — Provides a software method of detecting the status of program or erase cycles Unlock Bypass Program command — Reduces overall programming time when issuing multiple program command sequences HARDWARE FEATURES Any combination of sectors can be erased Ready/Busy# output (RY/BY#) — Hardware method for detecting program or erase cycle completion Hardware reset pin (RESET#) — Hardware method of resetting the internal state machine to the read mode WP#/ACC input pin — Write protect (WP#) function allows protection of two outermost boot sectors, regardless of sector protect status — Acceleration (ACC) function provides accelerated program times Sector protection — Hardware method of locking a sector, either in-system or using programming equipment, to prevent any program or erase operation within that sector — Temporary Sector Unprotect allows changing data in protected sectors in-system This Data Sheet states AMD’s current technical specifications regarding the Products described herein. This Data Sheet may be revised by subsequent versions or modifications due to changes in technical specifications. Publication# 23579 Rev: C Amendment/8 Issue Date: December 14, 2005 Refer to AMD’s Website (www.amd.com) for the latest information. DATASHEET GENERAL DESCRIPTION The Am29LV320D is a 32 megabit, 3.0 volt-only flash memory device, organized as 2,097,152 words of 16 bits each or 4,194,304 bytes of 8 bits each. Word mode data appears on DQ0–DQ15; byte mode data appears on DQ0–DQ7. The device is designed to be programmed in-system with the standard 3.0 volt VCC supply, and can also be programmed in standard EPROM programmers. The device is available with an access time of 90 or 120 ns. The devices are offered in 48-pin TSOP and 48-ball FBGA packages. Standard control pins—chip enable (CE#), write enable (WE#), and output enable (OE#)—control normal read and write operations, and avoid bus contention issues. The device requires only a single 3.0 volt power supply for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. or both. Customer Lockable parts may utilize the Secured Silicon sector as bonus space, reading and writing like any other flash sector, or may permanently lock their own code there. The device offers complete compatibility with the JEDEC single-power-supply Flash command set standard . Commands are written to the command register using standard microprocessor write timings. Reading data out of the device is similar to reading from other Flash or EPROM devices. The host system can detect whether a program or erase operation is complete by using the device status bits: RY/BY# pin, DQ7 (Data# Polling) and DQ6/DQ2 (toggle bits). After a program or erase cycle is completed, the device automatically returns to the read mode. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of the sectors of memory. This can be achieved in-system or via programming equipment. The device offers two power-saving features. When addresses are stable for a specified amount of time, the device enters the a utomatic sleep mode. The system can also place the device into the s tandby mode. Power consumption is greatly reduced in both modes. Am29LV320D Features The Secured Silicon sector is an extra sector capable of being permanently locked by AMD or customers. The S ecured Silicon Indicator Bit ( DQ7) is permanently set to a 1 if the part is factory locked, and set to a 0 if customer lockable. This way, customer lockable parts can never be used to replace a factory locked part. Note that the Am29LV320D has a Secured Silicon sector size of 64 Kbytes. AMD devices designated as replacements or substitutes, such as the Am29LV320M, have 256 bytes. This should be considered during system design. Factory locked parts provide several options. The Secured Silicon sector may store a secure, random 16 byte ESN (Electronic Serial Number), customer code (programmed through AMD’s ExpressFlash service), 2 Am29LV320D December 14, 2005 DATASHEET TABLE OF CONTENTS Continuity of Specifications ....................................................... i For More Information ................................................................. i Distinctive Characteristics . . . . . . . . . . . . . . . . . . 1 ARCHITECTURAL ADVANTAGES ...................................... 1 PERFORMANCE CHARACTERISTICS ............................... 1 SOFTWARE FEATURES ..................................................... 1 HARDWARE FEATURES .................................................... 1 General Description . . . . . . . . . . . . . . . . . . . . . . . 2 Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . 6 Special Package Handling Instructions .................................... 7 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 9 Device Bus Operations . . . . . . . . . . . . . . . . . . . . . 10 Table 1. Am29LV320D Device Bus Operations ..............................10 Reset Command ..................................................................... 25 Autoselect Command Sequence ............................................ 25 Table 13. Autoselect Codes ........................................................... 25 Enter Secured Silicon Sector/Exit Secured Silicon Sector Command Sequence .............................................................. 25 Byte/Word Program Command Sequence ............................. 26 Unlock Bypass Command Sequence .................................. 26 Figure 4. Program Operation ......................................................... 27 Chip Erase Command Sequence ........................................... 27 Sector Erase Command Sequence ........................................ 27 Erase Suspend/Erase Resume Commands ........................... 28 Figure 5. Erase Operation.............................................................. 28 Command Definitions ............................................................. 29 Table 14. Am29LV320D Command Definitions ............................. 29 Write Operation Status . . . . . . . . . . . . . . . . . . . . 30 DQ7: Data# Polling ................................................................. 30 Figure 6. Data# Polling Algorithm .................................................. 30 Word/Byte Configuration ........................................................ 11 Requirements for Reading Array Data ................................... 11 Writing Commands/Command Sequences ............................ 11 Accelerated Program Operation .......................................... 11 Autoselect Functions ........................................................... 11 Standby Mode ........................................................................ 12 Automatic Sleep Mode ........................................................... 12 RESET#: Hardware Reset Pin ............................................... 12 Output Disable Mode .............................................................. 12 Table 2. Top Boot Sector Addresses (Am29LV320DT) ..................13 Table 3. Top Boot Secured Silicon Sector Addresses ................... 14 Table 4. Bottom Boot Sector Addresses (Am29LV320DB) .............14 Table 5. Bottom Boot Secured Silicon Sector Addresses .............. 15 RY/BY#: Ready/Busy# ............................................................ 31 DQ6: Toggle Bit I .................................................................... 31 Figure 7. Toggle Bit Algorithm........................................................ 31 DQ2: Toggle Bit II ................................................................... 31 Reading Toggle Bits DQ6/DQ2 ............................................... 32 DQ5: Exceeded Timing Limits ................................................ 32 DQ3: Sector Erase Timer ....................................................... 32 Table 15. Write Operation Status ................................................... 33 Absolute Maximum Ratings . . . . . . . . . . . . . . . . 34 Figure 8. Maximum Negative Overshoot Waveform ...................... 34 Figure 9. Maximum Positive Overshoot Waveform........................ 34 Autoselect Mode ..................................................................... 16 Table 6. Autoselect Codes (High Voltage Method) ........................16 Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . 34 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 35 CMOS Compatible .................................................................. 35 Zero-Power Flash ................................................................. 36 Figure 10. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents) ............................................................. 36 Figure 11. Typical ICC1 vs. Frequency ............................................ 36 Sector/Sector Block Protection and Unprotection .................. 17 Table 7. Top Boot Sector/Sector Block Addresses for Protection/Unprotection .............................................................17 Table 8. Bottom Boot Sector/Sector Block Addresses for Protection/Unprotection ...........................................17 Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Figure 12. Test Setup.................................................................... 37 Table 16. Test Specifications ......................................................... 37 Figure 13. Input Waveforms and Measurement Levels ................. 37 Write Protect (WP#) ................................................................ 18 Temporary Sector Unprotect .................................................. 18 Figure 1. Temporary Sector Unprotect Operation........................... 18 Figure 2. In-System Sector Protect/Unprotect Algorithms .............. 19 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 38 Read-Only Operations ........................................................... 38 Figure 14. Read Operation Timings ............................................... 38 Secured Silicon Sector Flash Memory Region ....................... 20 Factory Locked: Secured Silicon Sector Programmed and Protected at the Factory ............................................... 20 Customer Lockable: Secured Silicon Sector NOT Programmed or Protected at the Factory .................................................. 20 Figure 3. Secured Silicon Sector Protect Verify .............................. 21 Hardware Reset (RESET#) .................................................... 39 Figure 15. Reset Timings ............................................................... 39 Word/Byte Configuration (BYTE#) ............................................. 40 Figure 16. BYTE# Timings for Read Operations............................ 40 Figure 17. BYTE# Timings for Write Operations............................ 40 Hardware Data Protection ...................................................... 21 Low VCC Write Inhibit ......................................................... 21 Write Pulse “Glitch” Protection ............................................ 21 Logical Inhibit ...................................................................... 21 Power-Up Write Inhibit ......................................................... 21 Common Flash Memory Interface (CFI) . . . . . . . 21 Table 9. CFI Query Identification String .......................................... 22 Table 10. System Interface String................................................... 22 Table 11. Device Geometry Definition ............................................ 23 Table 12. Primary Vendor-Specific Extended Query ...................... 24 Erase and Program Operations ................................................. 41 Figure 18. Program Operation Timings.......................................... Figure 19. Chip/Sector Erase Operation Timings .......................... Figure 20. Data# Polling Timings (During Embedded Algorithms). Figure 21. Toggle Bit Timings (During Embedded Algorithms)...... Figure 22. DQ2 vs. DQ6................................................................. 42 43 44 45 45 Temporary Sector Unprotect ..................................................... 46 Figure 23. Temporary Sector Unprotect Timing Diagram .............. 46 Figure 24. Accelerated Program Timing Diagram.......................... 46 Figure 25. Sector/Sector Block Protect and Unprotect Timing Diagram ............................................................. 47 Command Definitions . . . . . . . . . . . . . . . . . . . . . . 25 Reading Array Data ................................................................ 25 December 14, 2005 Alternate CE# Controlled Erase and Program Operations ........ 48 Figure 26. Alternate CE# Controlled Write Am29LV320D 3 DATASHEET (Erase/Program) Operation Timings ............................................... 49 Erase And Programming Performance . . . . . . . . 50 Latchup Characteristics . . . . . . . . . . . . . . . . . . . 50 TSOP and BGA Package Capacitance . . . . . . . 50 Data Retention . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 51 FBD048—48-ball Fine-Pitch Ball Grid Array (FBGA) 6 x 12 mm package ................................................................... 51 TS 048—48-Pin Standard TSOP ............................................... 52 Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 53 Ordering Information ............................................................ 53 Connection Diagrams .......................................................... 53 Global .................................................................................. 53 Table 3, Top Boot Secured Silicon Sector Addresses ......... 53 Sector/Sector Block Protection and Unprotection ............... 53 Secured Silicon Sector Flash Memory Region .................... 53 Global .................................................................................. 53 Ordering Information ............................................................ 53 Table 1, Am29LV320D Device Bus Operations ................... 53 Secured Silicon Sector Flash Memory Region .................... 53 Autoselect Command Sequence ......................................... 53 Table 14, Am29LV320D Command Definitions ................... 53 Erase and Program Operations table .................................. 53 Figure 3, Secured Silicon Sector Protect Verify ................... 53 Distinctive Characteristics ................................................... 53 Connection Diagrams .......................................................... 53 Ordering Information ............................................................ 53 Secured Silicon Flash Memory Region ............................... 53 Command Definitions .......................................................... 53 AC Characteristics ............................................................... 53 DC Characteristics ............................................................... 53 TSOP, SO, and BGA Package Capacitance ....................... 53 Distinctive Characteristics ................................................... 53 Secured Silicon Flash Memory Region ............................... 53 Command Definitions .......................................................... 54 Erase and Programming Performance ................................ 54 Distinctive Characteristics ................................................... 54 Secured Silicon Sector ........................................................ 54 Valid Combinations .............................................................. 54 Command Definitions .......................................................... 54 Ordering Information ............................................................ 54 Product Selector Guide ....................................................... 54 Global .................................................................................. 54 Ordering Information ............................................................ 54 Erase and Programming Performance ................................ 54 AC Characteristics ............................................................... 54 Erase and Program Operations ........................................... 54 Alternate CE# Control Erase and Program Operations ....... 54 Command Definitions .......................................................... 54 Global .................................................................................. 54 Common Flash Memory Interfacte (CFI) ............................. 54 Global .................................................................................. 54 4 Am29LV320D December 14, 2005 DATASHEET PRODUCT SELECTOR GUIDE Family Part Number Speed Option Max Access Time (ns) CE# Access (ns) OE# Access (ns) Standard Voltage Range: VCC = 2.7–3.6 V 90R Standard Voltage Range: VCC = 3.0–3.6 V Am29LV320D 90 90 90 40 120 120 120 50 BLOCK DIAGRAM VCC VSS RY/BY# Sector Switches Erase Voltage Generator DQ0–DQ15 (A-1) RESET# Input/Output Buffers WE# BYTE# State Control Command Register PGM Voltage Generator Chip Enable Output Enable Logic STB Data Latch CE# OE# STB VCC Detector Timer Address Latch Y-Decoder Y-Gating X-Decoder Cell Matrix A0–A20 December 14, 2005 Am29LV320D 5 DATASHEET CONNECTION DIAGRAMS A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# NC WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48-Pin Standard TSOP 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 BYTE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 6 Am29LV320D December 14, 2005 DATASHEET CONNECTION DIAGRAMS 48-Ball FBGA Top View, Balls Facing Down A6 A13 A5 A9 A4 WE# A3 B6 A12 B5 A8 B4 RESET# B3 C6 A14 C5 A10 C4 NC C3 A18 C2 A6 C1 A2 D6 A15 D5 A11 D4 A19 D3 A20 D2 A5 D1 A1 E6 A16 E5 DQ7 E4 DQ5 E3 DQ2 E2 DQ0 E1 A0 F6 G6 H6 VSS H5 DQ6 H4 DQ4 H3 DQ3 H2 DQ1 H1 VSS BYTE# DQ15/A-1 F5 DQ14 F4 DQ12 F3 DQ10 F2 DQ8 F1 CE# G5 DQ13 G4 VCC G3 DQ11 G2 DQ9 G1 OE# RY/BY# WP#/ACC A2 A7 A1 A3 B2 A17 B1 A4 Special Package Handling Instructions Special handling is required for Flash Memory products in molded (TSOP, BGA) packages. The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time. December 14, 2005 Am29LV320D 7 DATASHEET PIN DESCRIPTION A0–A20 = 21 Addresses DQ0–DQ14 = 15 Data Inputs/Outputs DQ15/A-1 = DQ15 (Data Input/Output, word mode), A-1 (LSB Address Input, byte mode) = Chip Enable = Output Enable = Write Enable = Hardware Write Protect/ Acceleration Pin = Hardware Reset Pin, Active Low = Selects 8-bit or 16-bit mode = Ready/Busy Output = 3.0 volt-only single power supply (see Product Selector Guide for speed options and voltage supply tolerances) = Device Ground = Pin Not Connected Internally LOGIC SYMBOL 21 A0–A20 DQ0–DQ15 (A-1) CE# OE# WE# WP#/ACC RESET# BYTE# RY/BY# 16 or 8 CE# OE# WE# WP#/ACC RESET# BYTE# RY/BY# VCC VSS NC 8 Am29LV320D December 14, 2005 DATASHEET ORDERING INFORMATION Standard Products AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of the following: Am29LV320D T 90 E C TEMPERATURE RANGE I = Industrial (–40°C to +85°C) F = Industrial (–40°C to +85°C) with Pb-free package C = Commercial (0°C to +70°C) D = Commercial (0°C to +70°C) with Pb-free package V = Automotive In-Cabin (-40°C to +105°C) Y = Automotive In-Cabin (-40°C to +105°C) with Pb-free package PACKAGE TYPE E = 48-Pin Thin Small Outline Package (TSOP) Standard Pinout (TS 048) WM = 48-ball Fine-Pitch Ball Grid Array (FBGA) 0.80 mm pitch, 6 x 12 mm package (FBD048) SPEED OPTION See Product Selector Guide and Valid Combinations BOOT CODE SECTOR ARCHITECTURE T = Top boot sector B = Bottom boot sector DEVICE NUMBER/DESCRIPTION Am29LV320D 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS Boot Sector Flash Memory 3.0 Volt-only Read, Program and Erase Valid Combinations for TSOP Packages AM29LV320DT90R, AM29LV320DB90R EC, EI, Am29LV320DT90, ED, EF Am29LV320DB90 AM29LV320DT120, AM29LV320DB120 Am29LV320DT120 EV, EY Am29LV320DB120 Speed (Ns) 90 90 120 120 VCC Range 3.0– 3.6V 2.7– 3.6V 2.7– 3.6V 2.7 – 3,6V Valid Combinations for FBGA Packages Order Number AM29LV320DT90, AM29LV320DB90 AM29LV320DT120, AM29LV320DB120 Am29LV320DT120 Am29LV320DB120 WMC, WMI, WMD, WMF WNV Package Marking L320DT90V, L320DB90V L320DT12V, L320DB12V L320DT12V L320DB12V C, I, D, F V, Y Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations. December 14, 2005 Am29LV320D 9 DATASHEET DEVICE BUS OPERATIONS This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information needed to execute the command. The contents of the Table 1. register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in further detail. Am29LV320D Device Bus Operations DQ8–DQ15 Operation Read Write Accelerated Program Standby Output Disable Reset Sector Protect (Note 2) Sector Unprotect (Note 2) Temporary Sector Unprotect CE# L L L VCC ± 0.3 V L X L L X OE# L H H X H X H H X WE# H L L X H X L L X RESET# H H H VCC ± 0.3 V H L VID VID VID WP#/ACC L/H (Note 3) VHH H L/H L/H L/H (Note 3) (Note 3) Addresses (Note 2) AIN AIN AIN X X X DQ0– DQ7 DOUT BYTE# = VIH DOUT BYTE# = VIL DQ8–DQ14 = High-Z, DQ15 = A-1 High-Z High-Z High-Z X X High-Z (Note 4) (Note 4) (Note 4) (Note 4) High-Z High-Z High-Z High-Z High-Z High-Z X X SA, A6 = L, (Note 4) A1 = H, A0 = L SA, A6 = H, (Note 4) A1 = H, A0 = L AIN (Note 4) (Note 4) Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 11.5–12.5 V, X = Don’t Care, SA = Sector Address, AIN = Address In, DIN = Data In, DOUT = Data Out Notes: 1. Addresses are A20:A0 in word mode (BYTE# = VIH), A20:A-1 in byte mode (BYTE# = VIL). 2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See “Sector/Sector Block Protection and Unprotection” on page 17. 3. If WP#/ACC = VIL, the two outermost boot sectors remain protected. If WP#/ACC = VIH, the two outermost boot sector protection depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection” on page 17. If WP#/ACC = VHH, all sectors are unprotected. 4. DIN or DOUT as required by command sequence, data polling, or sector protection algorithm. 10 Am29LV320D December 14, 2005 DATASHEET Word/Byte Configuration The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ0–DQ15 are active and controlled by CE# and OE#. If the BYTE# pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ0–DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8–DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function. Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. The “Word/Byte Configuration” on page 11 section contains details on programming data to the device using both standard and Unlock Bypass command sequences. An erase operation can erase one sector, multiple sectors, or the entire device. Table 2 on page 13 through Table 5 on page 15 indicate the address space that each sector occupies. A “sector address” is the address bits required to uniquely select a sector. ICC2 in the DC Characteristics table represents the active current specification for the write mode. The “AC Characteristics” on page 38 section contains timing specification tables and timing diagrams for write operations. Accelerated Program Operation The device offers accelerated program operations through the ACC function. This is one of two functions provided by the WP#/ACC pin. This function is primarily intended to allow faster manufacturing throughput at the factory. If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns the device to normal operation. Note that the WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Autoselect Functions If the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ7–DQ0. Standard read cycle timings apply in this mode. Refer to the “Autoselect Mode” on page 16 and “Autoselect Command Sequence” on page 25 sections for more information. ICC6 and ICC7 in the DC Characteristics table represent the current specifications for read-while-program and read-while-erase, respectively. Requirements for Reading Array Data To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is the power control and selects the device. OE# is the output control and gates array data to the output pins. WE# should remain at V IH . The BYTE# pin determines whether the device outputs array data in words or bytes. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. See “Requirements for Reading Array Data” on page 11 for more infor mation. Refer to the AC Read-Only Operations table for timing specifications and to Figure 14, on page 38 for the timing diagram. ICC1 in the DC Characteristics table represents the active current specification for reading array data. Writing Commands/Command Sequences To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH. For program operations, the BYTE# pin determines whether the device accepts program data in bytes or words. Refer to “Word/Byte Configuration” on page 11 for more information. The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the December 14, 2005 Am29LV320D 11 DATASHEET Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VCC ± 0.3 V. (Note that this is a more restricted voltage range than VIH.) If CE# and RESET# are held at VIH, but not within VCC ± 0.3 V, the device is in the standby mode, but the standby current is greater. The device requires standard access time (tCE) for read access when the device is in either of these standby modes, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. I CC3 i n the DC Characteristics table represents the standby current specification. SET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS±0.3 V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL but not within VSS±0.3 V, the standby current is greater. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a “0” (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is “1”), the reset operation is completed within a time of t READY (not during Embedded Algorithms). The system can read data tRH after the RESET# pin returns to VIH. Refer to the AC Characteristics tables for RESET# parameters and to Figure 15, on page 39 for the timing diagram. Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. ICC4 in the “DC Characteristics” on page 35 table represents the automatic sleep mode current specification. Output Disable Mode When the OE# input is at VIH, output from the device is disabled. The output pins are placed in the high impedance state. RESET#: Hardware Reset Pin The RESET# pin provides a hardware method of resetting the device to reading array data. When the RE- 12 Am29LV320D December 14, 2005 DATASHEET Table 2. Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 SA35 SA36 SA37 SA38 SA39 SA40 SA41 SA42 SA43 SA44 SA45 SA46 SA47 SA48 SA49 SA50 SA51 SA52 Sector Address A20–A12 000000xxx 000001xxx 000010xxx 000011xxx 000100xxx 000101xxx 000110xxx 000111xxx 001000xxx 001001xxx 001010xxx 001011xxx 001100xxx 001101xxx 001110xxx 001111xxx 010000xxx 010001xxx 010010xxx 010011xxx 010100xxx 010101xxx 010110xxx 010111xxx 011000xxx 011001xxx 011010xxx 011011xxx 011100xxx 011101xxx 011110xxx 011111xxx 100000xxx 100001xxx 100010xxx 100011xxx 100100xxx 100101xxx 100110xxx 100111xxx 101000xxx 101001xxx 101010xxx 101011xxx 101100xxx 101101xxx 101110xxx 101111xxx 110000xxx 110001xxx 110010xxx 110011xxx 110100xxx Top Boot Sector Addresses (Am29LV320DT) (Sheet 1 of 2) Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 000000h–00FFFFh 010000h–01FFFFh 020000h–02FFFFh 030000h–03FFFFh 040000h–04FFFFh 050000h–05FFFFh 060000h–06FFFFh 070000h–07FFFFh 080000h–08FFFFh 090000h–09FFFFh 0A0000h–0AFFFFh 0B0000h–0BFFFFh 0C0000h–0CFFFFh 0D0000h–0DFFFFh 0E0000h–0EFFFFh 0F0000h–0FFFFFh 100000h–10FFFFh 110000h–11FFFFh 120000h–12FFFFh 130000h–13FFFFh 140000h–14FFFFh 150000h–15FFFFh 160000h–16FFFFh 170000h–17FFFFh 180000h–18FFFFh 190000h–19FFFFh 1A0000h–1AFFFFh 1B0000h–1BFFFFh 1C0000h–1CFFFFh 1D0000h–1DFFFFh 1E0000h–1EFFFFh 1F0000h–1FFFFFh 200000h–20FFFFh 210000h–21FFFFh 220000h–22FFFFh 230000h–23FFFFh 240000h–24FFFFh 250000h–25FFFFh 260000h–26FFFFh 270000h–27FFFFh 280000h–28FFFFh 290000h–29FFFFh 2A0000h–2AFFFFh 2B0000h–2BFFFFh 2C0000h–2CFFFFh 2D0000h–2DFFFFh 2E0000h–2EFFFFh 2F0000h–2FFFFFh 300000h–30FFFFh 310000h–31FFFFh 320000h–32FFFFh 330000h–33FFFFh 340000h–34FFFFh (x16) Address Range 000000h–07FFFh 008000h–0FFFFh 010000h–17FFFh 018000h–01FFFFh 020000h–027FFFh 028000h–02FFFFh 030000h–037FFFh 038000h–03FFFFh 040000h–047FFFh 048000h–04FFFFh 050000h–057FFFh 058000h–05FFFFh 060000h–067FFFh 068000h–06FFFFh 070000h–077FFFh 078000h–07FFFFh 080000h–087FFFh 088000h–08FFFFh 090000h–097FFFh 098000h–09FFFFh 0A0000h–0A7FFFh 0A8000h–0AFFFFh 0B0000h–0B7FFFh 0B8000h–0BFFFFh 0C0000h–0C7FFFh 0C8000h–0CFFFFh 0D0000h–0D7FFFh 0D8000h–0DFFFFh 0E0000h–0E7FFFh 0E8000h–0EFFFFh 0F0000h–0F7FFFh 0F8000h–0FFFFFh 100000h–107FFFh 108000h–10FFFFh 110000h–117FFFh 118000h–11FFFFh 120000h–127FFFh 128000h–12FFFFh 130000h–137FFFh 138000h–13FFFFh 140000h–147FFFh 148000h–14FFFFh 150000h–157FFFh 158000h–15FFFFh 160000h–167FFFh 168000h–16FFFFh 170000h–177FFFh 178000h–17FFFFh 180000h–187FFFh 188000h–18FFFFh 190000h–197FFFh 198000h–19FFFFh 1A0000h–1A7FFFh December 14, 2005 Am29LV320D 13 DATASHEET Table 2. Sector SA53 SA54 SA55 SA56 SA57 SA58 SA59 SA60 SA61 SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 Sector Address A20–A12 110101xxx 110110xxx 110111xxx 111000xxx 111001xxx 111010xxx 111011xxx 111100xxx 111101xxx 111110xxx 111111000 111111001 111111010 111111011 111111100 111111101 111111110 111111111 Top Boot Sector Addresses (Am29LV320DT) (Sheet 2 of 2) Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4 (x8) Address Range 350000h–35FFFFh 360000h–36FFFFh 370000h–37FFFFh 380000h–38FFFFh 390000h–39FFFFh 3A0000h–3AFFFFh 3B0000h–3BFFFFh 3C0000h–3CFFFFh 3D0000h–3DFFFFh 3E0000h–3EFFFFh 3F0000h–3F1FFFh 3F2000h–3F3FFFh 3F4000h–3F5FFFh 3F6000h–3F7FFFh 3F8000h–3F9FFFh 3FA000h–3FBFFFh 3FC000h–3FDFFFh 3FE000h–3FFFFFh (x16) Address Range 1A8000h–1AFFFFh 1B0000h–1B7FFFh 1B8000h–1BFFFFh 1C0000h–1C7FFFh 1C8000h–1CFFFFh 1D0000h–1D7FFFh 1D8000h–1DFFFFh 1E0000h–1E7FFFh 1E8000h–1EFFFFh 1F0000h–1F7FFFh 1F8000h–1F8FFFh 1F9000h–1F9FFFh 1FA000h–1FAFFFh 1FB000h–1FBFFFh 1FC000h–1FCFFFh 1FD000h–1FDFFFh 1FE000h–1FEFFFh 1FF000h–1FFFFFh Note: The address range is A20:A-1 in byte mode (BYTE#=VIL) or A20:A0 in word mode (BYTE#=VIH). Table 3. Sector Address A20–A12 111111xxx Top Boot Secured Silicon Sector Addresses (x8) Address Range 3F0000h–3FFFFFh (x16) Address Range 1F8000h–1FFFFFh Sector Size (Kbytes/Kwords) 64/32 Table 4. Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 Bottom Boot Sector Addresses (Am29LV320DB) (Sheet 1 of 2) Sector Size (Kbytes/Kwords) 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 000000h-001FFFh 002000h-003FFFh 004000h-005FFFh 006000h-007FFFh 008000h-009FFFh 00A000h-00BFFFh 00C000h-00DFFFh 00E000h-00FFFFh 010000h-01FFFFh 020000h-02FFFFh 030000h-03FFFFh 040000h-04FFFFh 050000h-05FFFFh 060000h-06FFFFh 070000h-07FFFFh 080000h-08FFFFh 090000h-09FFFFh 0A0000h-0AFFFFh 0B0000h-0BFFFFh 0C0000h-0CFFFFh 0D0000h-0DFFFFh 0E0000h-0EFFFFh 0F0000h-0FFFFFh 100000h-10FFFFh 110000h-11FFFFh 120000h-12FFFFh 130000h-13FFFFh 140000h-14FFFFh 150000h-15FFFFh 160000h-16FFFFh (x16) Address Range 000000h–000FFFh 001000h–001FFFh 002000h–002FFFh 003000h–003FFFh 004000h–004FFFh 005000h–005FFFh 006000h–006FFFh 007000h–007FFFh 008000h–00FFFFh 010000h–017FFFh 018000h–01FFFFh 020000h–027FFFh 028000h–02FFFFh 030000h–037FFFh 038000h–03FFFFh 040000h–047FFFh 048000h–04FFFFh 050000h–057FFFh 058000h–05FFFFh 060000h–067FFFh 068000h–06FFFFh 070000h–077FFFh 078000h–07FFFFh 080000h–087FFFh 088000h–08FFFFh 090000h–097FFFh 098000h–09FFFFh 0A0000h–0A7FFFh 0A8000h–0AFFFFh 0B0000h–0B7FFFh Sector Address A20–A12 000000000 000000001 000000010 000000011 000000100 000000101 000000110 000000111 000001xxx 000010xxx 000011xxx 000100xxx 000101xxx 000110xxx 000111xxx 001000xxx 001001xxx 001010xxx 001011xxx 001100xxx 001101xxx 001110xxx 001111xxx 010000xxx 010001xxx 010010xxx 010011xxx 010100xxx 010101xxx 010110xxx 14 Am29LV320D December 14, 2005 DATASHEET Table 4. Sector SA30 SA31 SA32 SA33 SA34 SA35 SA36 SA37 SA38 SA39 SA40 SA41 SA42 SA43 SA44 SA45 SA46 SA47 SA48 SA49 SA50 SA51 SA52 SA53 SA54 SA55 SA56 SA57 SA58 SA59 SA60 SA61 SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 Bottom Boot Sector Addresses (Am29LV320DB) (Sheet 2 of 2) Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 170000h-17FFFFh 180000h-18FFFFh 190000h-19FFFFh 1A0000h-1AFFFFh 1B0000h-1BFFFFh 1C0000h-1CFFFFh 1D0000h-1DFFFFh 1E0000h-1EFFFFh 1F0000h-1FFFFFh 200000h-20FFFFh 210000h-21FFFFh 220000h-22FFFFh 230000h-23FFFFh 240000h-24FFFFh 250000h-25FFFFh 260000h-26FFFFh 270000h-27FFFFh 280000h-28FFFFh 290000h-29FFFFh 2A0000h-2AFFFFh 2B0000h-2BFFFFh 2C0000h-2CFFFFh 2D0000h-2DFFFFh 2E0000h-2EFFFFh 2F0000h-2FFFFFh 300000h-30FFFFh 310000h-31FFFFh 320000h-32FFFFh 330000h-33FFFFh 340000h-34FFFFh 350000h-35FFFFh 360000h-36FFFFh 370000h-37FFFFh 380000h-38FFFFh 390000h-39FFFFh 3A0000h-3AFFFFh 3B0000h-3BFFFFh 3C0000h-3CFFFFh 3D0000h-3DFFFFh 3E0000h-3EFFFFh 3F0000h-3FFFFFh (x16) Address Range 0B8000h–0BFFFFh 0C0000h–0C7FFFh 0C8000h–0CFFFFh 0D0000h–0D7FFFh 0D8000h–0DFFFFh 0E0000h–0E7FFFh 0E8000h–0EFFFFh 0F0000h–0F7FFFh 0F8000h–0FFFFFh 100000h–107FFFh 108000h–10FFFFh 110000h–117FFFh 118000h–11FFFFh 120000h–127FFFh 128000h–12FFFFh 130000h–137FFFh 138000h–13FFFFh 140000h–147FFFh 148000h–14FFFFh 150000h–157FFFh 158000h–15FFFFh 160000h–167FFFh 168000h–16FFFFh 170000h–177FFFh 178000h–17FFFFh 180000h–187FFFh 188000h–18FFFFh 190000h–197FFFh 198000h–19FFFFh 1A0000h–1A7FFFh 1A8000h–1AFFFFh 1B0000h–1B7FFFh 1B8000h–1BFFFFh 1C0000h–1C7FFFh 1C8000h–1CFFFFh 1D0000h–1D7FFFh 1D8000h–1DFFFFh 1E0000h–1E7FFFh 1E8000h–1EFFFFh 1F0000h–1F7FFFh 1F8000h–1FFFFFh Sector Address A20–A12 010111xxx 011000xxx 011001xxx 011010xxx 011011xxx 011100xxx 011101xxx 011110xxx 011111xxx 100000xxx 100001xxx 100010xxx 100011xxx 100100xxx 100101xxx 100110xxx 100111xxx 101000xxx 101001xxx 101010xxx 101011xxx 101100xxx 101101xxx 101110xxx 101111xxx 111000xxx 110001xxx 110010xxx 110011xxx 110100xxx 110101xxx 110110xxx 110111xxx 111000xxx 111001xxx 111010xxx 111011xxx 111100xxx 111101xxx 111110xxx 111111xxx Note: The address range is A20:A-1 in byte mode (BYTE#=VIL) or A20:A0 in word mode (BYTE#=VIH). Table 5. Sector Address A20–A12 000000xxx Bottom Boot Secured Silicon Sector Addresses Sector Size (Kbytes/Kwords) 64/32 (x8) Address Range 000000h-00FFFFh (x16) Address Range 00000h-07FFFh December 14, 2005 Am29LV320D 15 DATASHEET Autoselect Mode The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. However, the autoselect codes can also be accessed in-system through the command register. When using programming equipment, the autoselect mode requires VID (11.5 V to 12.5 V) on address pin A9. Address pins A6, A1, and A0 must be as shown in Table 6 on page 16. In addition, when verifying sector Table 6. protection, the sector address must appear on the appropriate highest order address bits (see Table 2 on page 13 through Table 5 on page 15). Table 6 on page 16 shows the remaining address bits that are don’t care. When all necessary bits are set as required, the programming equipment may then read the corresponding identifier code on DQ7–DQ0. To access the autoselect codes in-system, the host system can issue the autoselect command via the command register, as shown in Table 14 on page 29. This method does not require VID. Refer to the “Autoselect Command Sequence” on page 25 section for more information. Autoselect Codes (High Voltage Method) DQ8 to DQ15 A20 to A12 X X SA X A11 to A10 X X X X A8 to A7 X X X X A5 to A2 X X X X DQ7 to DQ0 01h F6 (T), F9h (B) 01h (protected), 00h (unprotected) 99h (factory locked), 19h (not factory locked) Description Manufacturer ID: AMD Device ID: Am29LV320D Sector Protection Verification Secured Silicon Sector Indicator Bit (DQ7) CE# L L L L OE# L L L L WE# H H H H A9 VID VID VID VID A6 L L L L A1 L L H H A0 L H L H BYTE#= VIH X 22h X X BYTE# = VIL X X X X Legend: T = Top Boot Block, B = Bottom Boot Block, L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care. 16 Am29LV320D December 14, 2005 DATASHEET Sector/Sector Block Protection and Unprotection The hardware sector protection feature disables both program and erase operations in any sector. The hardware sector unprotection feature re-enables both program and erase operations in previously protected sectors. Sector protection/unprotection can be implemented via two methods. (Note: For the following discussion, the term “sector” applies to both sectors and sector blocks. A sector block consists of two or more adjacent sectors that are protected or unprotected at the same time (see Table 7 on page 17 and Table 8 on page 17). Table 7. Top Boot Sector/Sector Block Addresses for Protection/Unprotection A20–A12 000000XXX, 000001XXX, 000010XXX 000011XXX 0001XXXXX 0010XXXXX 0011XXXXX 0100XXXXX 0101XXXXX 0110XXXXX 0111XXXXX 1000XXXXX 1001XXXXX 1010XXXXX 1011XXXXX 1100XXXXX 1101XXXXX 1110XXXXX 111100XXX, 111101XXX, 111110XXX 111111000 111111001 111111010 111111011 111111100 111111101 111111110 111111111 Sector/Sector Block Size Sector / Sector Block SA62-SA59 SA58-SA55 SA54-SA51 SA50-SA47 SA46-SA43 SA42-SA39 SA38-SA35 SA34-SA31 SA30-SA27 SA26-SA23 SA22–SA19 SA18-SA15 SA14-SA11 SA10-SA8 SA7 A20–A12 1101XXXXX 1100XXXXX 1011XXXXX 1010XXXXX 1001XXXXX 1000XXXXX 0111XXXXX 0110XXXXX 0101XXXXX 0100XXXXX 0011XXXXX 0010XXXXX 0001XXXXX 000011XXX, 000010XXX, 000001XXX 000000111 000000110 000000101 000000100 000000011 000000010 000000001 000000000 Sector/Sector Block Size 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 192 (3x64) Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes Sector / Sector Block SA0-SA3 256 (4x64) Kbytes SA6 SA5 SA4-SA7 SA8-SA11 SA12-SA15 SA16-SA19 SA20-SA23 SA24-SA27 SA28-SA31 SA32-SA35 SA36-SA39 SA40-SA43 SA44-SA47 SA48-SA51 SA52-SA55 SA56-SA59 SA60-SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 192 (3x64) Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes SA4 SA3 SA2 SA1 SA0 Sector Protection and unprotection requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 2, on page 19 shows the algorithms and Figure 25, on page 47 shows the timing diagram. This method uses standard microprocessor bus cycle timing. For sector unprotect, all unprotected sectors must first be protected prior to the first sector unprotect write cycle. The sector unprotect algorithm unprotects all sectors in parallel. All previously protected sectors must be individually re-protected. To change data in protected sectors efficiently, the temporary sector unprotect function is available. See “Temporary Sector Unprotect” on page 18. The alternate method intended only for programming equipment, and requires VID on address pin A9 and OE#. This method is compatible with programmer routines written for earlier 3.0 volt-only AMD flash devices. For detailed information, contact an AMD representative. The device is shipped with all sectors unprotected. AMD offers the option of programming and protecting sectors at its factory prior to shipping the device through AMD’s ExpressFlash™ Service. Contact an AMD representative for details. It is possible to determine whether a sector is protected or unprotected. See “Autoselect Mode” on page 16 for details. Table 8. Bottom Boot Sector/Sector Block Addresses for Protection/Unprotection Sector / Sector Block A20–A12 111111XXX, 111110XXX, 111101XXX, 111100XXX 1110XXXXX Sector/Sector Block Size SA70-SA67 256 (4x64) Kbytes SA66-SA63 256 (4x64) Kbytes December 14, 2005 Am29LV320D 17 DATASHEET Write Protect (WP#) The Write Protect function provides a hardware method of protecting certain boot sectors without using VID. This function is one of two provided by the WP#/ACC pin. If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the two “outermost” 8 Kbyte boot sectors independently of whether those sectors were protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection” on page 17. The two outermost 8 Kbyte boot sectors are the two sectors containing the lowest addresses in a bottom-boot-configured device, or the two sectors containing the highest addresses in a top-boot-configured device. If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the two outermost 8K Byte boot sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these two sectors depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection” on page 17. Note that the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. erased by selecting the sector addresses. Once VID is removed from the RESET# pin, all the previously protected sectors are protected again. Figure 1, on page 18 shows the algorithm, and Figure 23, on page 46 shows the timing diagrams, for this feature. START RESET# = VID (Note 1) Perform Erase or Program Operations RESET# = VIH Temporary Sector Unprotect Completed (Note 2) Temporary Sector Unprotect This feature allows temporary unprotection of previously protected sectors to change data in-system. The Sector Unprotect mode is activated by setting the RESET# pin to VID (11.5 V – 12.5 V). During this mode, formerly protected sectors can be programmed or Notes: 1. All protected sectors unprotected (If WP#/ACC = VIL, outermost boot sectors remain protected). 2. All previously protected sectors are protected once again. Figure 1. Temporary Sector Unprotect Operation 18 Am29LV320D December 14, 2005 DATASHEET START PLSCNT = 1 RESET# = VID Wait 1 μs Protect all sectors: The indicated portion of the sector protect algorithm must be performed for all unprotected sectors prior to issuing the first sector unprotect address START PLSCNT = 1 RESET# = VID Wait 1 μs Temporary Sector Unprotect Mode No First Write Cycle = 60h? Yes Set up sector address Sector Protect: Write 60h to sector address with A6 = 0, A1 = 1, A0 = 0 Wait 150 µs Verify Sector Protect: Write 40h to sector address with A6 = 0, A1 = 1, A0 = 0 Read from sector address with A6 = 0, A1 = 1, A0 = 0 No No First Write Cycle = 60h? Yes All sectors protected? Yes Set up first sector address Sector Unprotect: Write 60h to sector address with A6 = 1, A1 = 1, A0 = 0 Temporary Sector Unprotect Mode Increment PLSCNT Reset PLSCNT = 1 Wait 15 ms Verify Sector Unprotect: Write 40h to sector address with A6 = 1, A1 = 1, A0 = 0 No No PLSCNT = 25? Yes Data = 01h? Increment PLSCNT Yes No Yes No Read from sector address with A6 = 1, A1 = 1, A0 = 0 Set up next sector address Device failed Protect another sector? No Remove VID from RESET# PLSCNT = 1000? Yes Data = 00h? Yes Device failed Write reset command Last sector verified? Yes No Sector Protect Algorithm Sector Protect complete Sector Unprotect Algorithm Remove VID from RESET# Write reset command Sector Unprotect complete Figure 2. In-System Sector Protect/Unprotect Algorithms December 14, 2005 Am29LV320D 19 DATASHEET Secured Silicon Sector Flash Memory Region The Secured Silicon sector provides a Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The Secured Silicon sector uses a Secured Silicon Indicator Bit (DQ7) to indicate whether or not the Secured Silicon sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevents cloning of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. N ote that the Am29LV320D has a Secured Silicon sector size of 64 Kbytes. AMD devices designated as replacements or substitutes, such as the Am29LV320M, have 256 bytes. This should be considered during system design. AMD offers the device with the Secured Silicon sector either factory locked or customer lockable. The factory-locked version is always protected when shipped from the factory, and has the Secured Silicon sector Indicator Bit permanently set to a “1.” The customer-lockable version is shipped with the Secured Silicon sector unprotected, allowing customers to utilize the that sector in any manner they choose. The customer-lockable version has the Secured Silicon Indicator Bit permanently set to a “0.” Thus, the Secured Silicon Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory locked. The system accesses the Secured Silicon sector through a command sequence (see “Enter Secured Silicon Sector/Exit Secured Silicon Sector Command Sequence” on page 25). After the system writes the Enter Secured Silicon sector command sequence, it may read the Secured Silicon Sector by using the addresses normally occupied by the boot sectors. This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending commands to the boot sectors. Factory Locked: Secured Silicon Sector Programmed and Protected at the Factory In a factory locked device, the Secured Silicon Sector is protected when the device is shipped from the factory. The Secured Silicon Sector cannot be modified in any way. The device is available preprogrammed with one of the following: ■ A random, secure ESN only ■ Customer code through the ExpressFlash service ■ Both a random, secure ESN and customer code through the ExpressFlash service. In devices that have an ESN, a Bottom Boot device has the 16-byte (8-word) ESN in sector 0 at addresses 00000h–0000Fh in byte mode (or 00000h–00007h in word mode). In the Top Boot device the ESN is in sector 63 at addresses 3F0000h–3F000Fh in byte mode (or 1F8000h–1F8007h in word mode). Note that in upcoming top boot versions of this device, the ESN is located in sector 70 at addresses 3FE000h–3FE00Fh in byte mode (or 1FF000h–1FF007h in word mode). Customers may opt to have their code programmed by AMD through the AMD ExpressFlash service. AMD programs the customer’s code, with or without the random ESN. The devices are then shipped from AMD’s factory with the Secured Silicon Sector permanently locked. Contact an AMD representative for details on using AMD’s ExpressFlash service. Customer Lockable: Secured Silicon Sector NOT Programmed or Protected at the Factory The customer lockable version allows the Secured Silicon Sector to be programmed once and then permanently locked after it ships from AMD. Note that the Am29LV320D has a Secured Silicon Sector size of 64 Kbytes. AMD devices designated as replacements or substitutes, such as the Am29LV320M, have 256 bytes. This should be considered during system design. Additionally, note the change in the location of the ESN in upcoming top boot factory locked devices. Note that the accelerated programming (ACC) and unlock bypass functions are not available when programming the Secured Silicon Sector. The Secured Silicon Sector area can be protected using the following procedures: ■ Write the three-cycle Enter Secured Silicon Sector command sequence, and then follow the in-system sector protect algorithm as shown in Figure 2, on page 19, except that RESET# may be at either VIH or VID. This allows in-system protection of the Secured Silicon Sector without raising any device pin to a high voltage. Note that this method is only applicable to the Secured Silicon Sector. ■ To verify the protect/unprotect status of the Secured Silicon Sector, follow the algorithm shown in Figure 3, on page 21. Once the Secured Silicon Sector is locked and verified, the system must write the Exit Secured Silicon Sector command sequence to return to reading and writing the remainder of the array. The Secured Silicon Sector protection must be used with caution since, once protected, there is no procedure available for unprotecting the Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way. 20 Am29LV320D December 14, 2005 DATASHEET Write Pulse “Glitch” Protection Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. START RESET# = VIH or VID Wait 1 μs Write 60h to any address If data = 00h, SecSi Sector is unprotected. If data = 01h, SecSi Sector is protected. Logical Inhibit Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a logical one. Power-Up Write Inhibit Remove VIH or VID from RESET# Write 40h to SecSi Sector address with A6 = 0, A1 = 1, A0 = 0 Read from SecSi Sector address with A6 = 0, A1 = 1, A0 = 0 Write reset command SecSi Sector Protect Verify complete If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. COMMON FLASH MEMORY INTERFACE (CFI) The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h in word mode (or address AAh in byte mode), any time the device is ready to read array data. The system can read CFI information at the addresses given in Table 9 on page 22 through Table 12 on page 24. To terminate reading CFI data, the system must write the reset command. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Table 9 on page 22 through Table 12 on page 24. The system must write the reset command to return the device to the reading array data. For further information, please refer to the CFI Specification, CFI Publication 100, and the application note “Common Flash Interface Version 1.4 Vendor Specific Extensions”. Contact an AMD representative for copies of these documents. Figure 3. Secured Silicon Sector Protect Verify Hardware Data Protection The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadver tent writes (refer to Table 14 on page 29 for command definitions). In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise. Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to the read mode. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when V CC i s greater than VLKO. December 14, 2005 Am29LV320D 21 DATASHEET Table 9. Addresses (Word Mode) 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah Addresses (Byte Mode) 20h 22h 24h 26h 28h 2Ah 2Ch 2Eh 30h 32h 34h Data 0051h 0052h 0059h 0002h 0000h 0040h 0000h 0000h 0000h 0000h 0000h CFI Query Identification String Description Query Unique ASCII string “QRY” Primary OEM Command Set Address for Primary Extended Table Alternate OEM Command Set (00h = none exists) Address for Alternate OEM Extended Table (00h = none exists) Table 10. Addresses (Word Mode) 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h Addresses (Byte Mode) 36h 38h 3Ah 3Ch 3Eh 40h 42h 44h 46h 48h 4Ah 4Ch Data 0027h 0036h 0000h 0000h 0004h 0000h 000Ah 0000h 0005h 0000h 0004h 0000h System Interface String Description VCC Min. (write/erase) D7–D4: volt, D3–D0: 100 millivolt VCC Max. (write/erase) D7–D4: volt, D3–D0: 100 millivolt VPP Min. voltage (00h = no VPP pin present) VPP Max. voltage (00h = no VPP pin present) Typical timeout per single byte/word write 2N µs Typical timeout for Min. size buffer write 2N µs (00h = not supported) Typical timeout per individual block erase 2N ms Typical timeout for full chip erase 2N ms (00h = not supported) Max. timeout for byte/word write 2N times typical Max. timeout for buffer write 2N times typical Max. timeout per individual block erase 2N times typical Max. timeout for full chip erase 2N times typical (00h = not supported) 22 Am29LV320D December 14, 2005 DATASHEET Table 11. Addresses (Word Mode) 27h 28h 29h 2Ah 2Bh 2Ch 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch Addresses (Byte Mode) 4Eh 50h 52h 54h 56h 58h 5Ah 5Ch 5Eh 60h 62h 64h 66h 68h 6Ah 6Ch 6Eh 70h 72h 74h 76h 78h Data 0016h 0002h 0000h 0000h 0000h 0002h 0007h 0000h 0020h 0000h 003Eh 0000h 0000h 0001h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h Device Size = 2 byte Flash Device Interface description (refer to CFI publication 100) Max. number of bytes in multi-byte write = 2N (00h = not supported) Number of Erase Block Regions within device Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) N Device Geometry Definition Description Erase Block Region 2 Information Erase Block Region 3 Information Erase Block Region 4 Information December 14, 2005 Am29LV320D 23 DATASHEET Table 12. Addresses (Word Mode) 40h 41h 42h 43h 44h 45h Addresses (Byte Mode) 80h 82h 84h 86h 88h 8Ah Primary Vendor-Specific Extended Query Description Query-unique ASCII string “PRI” Major version number, ASCII Minor version number, ASCII Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Silicon Revision Number (Bits 7-2) Data 0050h 0052h 0049h 0031h 0031h 0000h 46h 47h 48h 49h 4Ah 4Bh 4Ch 4Dh 8Ch 8Eh 90h 92h 94h 96h 98h 9Ah 0002h 0004h 0001h 0004h 0000h 0000h 0000h 00B5h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write Sector Protect 0 = Not Supported, X = Number of sectors in per group Sector Temporary Unprotect 00 = Not Supported, 01 = Supported Sector Protect/Unprotect scheme 04 = 29LV800 mode Simultaneous Operation 00 = Not Supported Burst Mode Type 00 = Not Supported, 01 = Supported Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV Top/Bottom Boot Sector Flag 02h = Bottom Boot Device, 03h = Top Boot Device 4Eh 9Ch 00C5h 4Fh 9Eh 000Xh 24 Am29LV320D December 14, 2005 DATASHEET COMMAND DEFINITIONS Writing specific address and data commands or sequences into the command register initiates device operations. Table 14 on page 29 defines the valid register command sequences. Note that writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. A reset command is required to return the device to normal operation. All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on the rising edge of WE# or CE#, whichever happens first. Refer to the AC Characteristics section for timing diagrams. pend-read mode. Once programming begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to the read mode. If the device entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns the device to the erase-suspend-read mode. If DQ5 goes high during a program or erase operation, writing the reset command returns the device to the read mode (or erase-suspend-read mode if the device was in Erase Suspend). Reading Array Data The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is ready to read array data after completing an Embedded Program or Embedded Erase algorithm. After the device accepts an Erase Suspend command, the device enters the erase-suspend-read mode, after which the system can read data from any non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See “Erase Suspend/Erase Resume Commands” on page 28 for more information. The system must issue the reset command to return the device to the read (or erase-suspend-read) mode if DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See the next section, “Reset Command, for more information. See also “Requirements for Reading Array Data” on page 11 for more information. The Read-Only Operations table provides the read parameters, and Figure 14, on page 38 shows the timing diagram. Autoselect Command Sequence The autoselect command sequence allows the host system to read several identifier codes at specific addresses: Table 13. Identifier Code Manufacturer ID Device ID Secured Silicon Sector Factory Protect Sector Group Protect Verify Autoselect Codes Address 00h 01h 03h (SA)02h Table 14 on page 29 shows the address and data requirements. This method is an alternative to that shown in Table 6 on page 16, which is intended for PROM programmers and requires VID on address pin A9. The autoselect command sequence may be written to an address within sector that is either in the read or erase-suspend-read mode. The autoselect command may not be written while the device is actively programming or erasing. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains the autoselect command. The device then enters the autoselect mode. The system may read at any address any number of times without initiating another autoselect command sequence. The system must write the reset command to return to the read mode (or erase-suspend-read mode if the device was previously in Erase Suspend). Reset Command Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don’t cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to which the system was writing to the read mode. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to which the system was writing to the read mode. If the program command sequence is written to a sector that is in the Erase Suspend mode, writing the reset command retur ns the device to the erase-susDecember 14, 2005 Enter Secured Silicon Sector/Exit Secured Silicon Sector Command Sequence The Secured Silicon sector provides a secured data area containing a random, sixteen-byte electronic serial number (ESN). The system can access the Secured Silicon sector by issuing the three-cycle Enter Secured Silicon sector command sequence. The device continues to access the Secured Silicon sector until the system issues the four-cycle Exit Secured Sil- Am29LV320D 25 DATASHEET icon sector command sequence. The Exit Secured Silicon sector command sequence returns the device to normal operation. Table 14 on page 29 shows the address and data requirements for both command sequences. Note that the ACC function and unlock bypass modes are not available when the device enters the Secured Silicon sector. See also “Secured Silicon Sector Flash Memory Region” on page 20 for further information. data is still “0.” Only erase operations can convert a “0” to a “1.” Unlock Bypass Command Sequence The unlock bypass feature allows the system to program bytes or words to the device faster than using the standard program command sequence. The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. Table 14 on page 29 shows the requirements for the command sequence. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the data 90h. The second cycle need only contain the data 00h. The device then re turns to the read mode. The device offers accelerated program operations through the WP#/ACC pin. When the system asserts VHH on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass program command sequence. The device uses the higher voltage on the WP#/ACC pin to accelerate the operation. Note that the WP#/ACC pin must not be at VHH any operation other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Figure 4, on page 27 illustrates the algorithm for the program operation. Refer to the table “Erase and Program Operations” on page 41 for parameters, and Figure 18, on page 42 for timing diagrams. Byte/Word Program Command Sequence The system may program the device by word or byte, depending on the state of the BYTE# pin. Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. Table 14 on page 29 shows the address and data requirements for the byte program command sequence. N ote that the autoselect, Secured Silicon sector, and CFI modes are unavailable while a programming operation is in progress. When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or RY/BY#. Refer to “Write Operation Status” on page 30 for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device returns to the read mode, to ensure data integrity. Programming is allowed in any sequence and across sector boundaries. A b it cannot be programmed from “0” back to a “1.” A ttempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read shows that the 26 Am29LV320D December 14, 2005 DATASHEET RY/BY#. Refer to “Write Operation Status” on page 30 for information on these status bits. START Write Program Command Sequence Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once the device returns to reading array data, to ensure data integrity. Figure 5, on page 28 illustrates the algorithm for the erase operation. Refer to table “Erase and Program Operations” on page 41 for parameters, and Figure 19, on page 43 section for timing diagrams. Embedded Program algorithm in progress Data Poll from System Sector Erase Command Sequence Verify Data? No Yes No Increment Address Last Address? Yes Programming Completed Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and the sector erase command. Table 14 on page 29 shows the address and data requirements for the sector erase command sequence. Note that the autoselect, Secured Silicon sector, and CFI modes are unavailable while an erase operation is in progress. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of 50 µs occurs. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 µs, otherwise the last address and command may not be accepted, and erasure may begin. It is recommended that processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is written. Any command other than Sec to r Er as e or Er as e Su sp end dur in g th e time-out period resets the device to the read mode. T he system must rewrite the command sequence and any additional addresses and commands. The system can monitor DQ3 to determine if the sector erase timer timed out (See the section “DQ3: Sector Erase Timer” on page 32.). The time-out begins from the rising edge of the final WE# pulse in the command sequence. When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by reading DQ7, DQ6, 27 Note: See Table 14 on page 29 for program command sequence. Figure 4. Program Operation Chip Erase Command Sequence Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table 14 on page 29 shows the address and data requirements for the chip erase command sequence. Note that the autoselect, Secured Silicon sector, and CFI modes are unavailable while an erase operation is in progress. When the Embedded Erase algorithm is complete, the device returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or December 14, 2005 Am29LV320D DATASHEET DQ2, or RY/BY# in the erasing sector. Refer to “Write Operation Status” on page 30 for information on these status bits. Once the sector erase operation begins, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once the device returns to reading array data, to ensure data integrity. Figure 5, on page 28 illustrates the algorithm for the erase operation. Refer to table “Erase and Program Operations” on page 41 for parameters, and Figure 19, on page 43 for timing diagrams. mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard Byte Program operation. Refer to “Write Operation Status” on page 30 for more information. In the erase-suspend-read mode, the system can also issue the autoselect command sequence. Refer to “Autoselect Mode” on page 16 and “Autoselect Command Sequence” on page 25 for details. To resume the sector erase operation, the system must write the Erase Resume command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip resumes erasing. Erase Suspend/Erase Resume Commands The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. This command is valid only during the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of 20 µs to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After the erase operation is suspended, the device enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to the “Write Operation Status” on page 30 section for information on these status bits. After an erase-suspended program operation is complete, the device returns to the erase-suspend-read START Write Erase Command Sequence (Notes 1, 2) Data Poll to Erasing Bank from System Embedded Erase algorithm in progress No Data = FFh? Yes Erasure Completed Notes: 1. See Table 14 on page 29 for erase command sequence. 2. See the section on DQ3 for information on the sector erase timer. Figure 5. Erase Operation 28 Am29LV320D December 14, 2005 DATASHEET Command Definitions Table 14. Command Sequence (Note 1) Read (Note 6) Reset (Note 7) Manufacturer ID Autoselect (Note 8) Device ID Secured Silicon Factory Protect (Note 9) Sector Protect Verify (Note 10) Word Byte Word Byte Word Byte Word 4 Cycles First Addr RA XXX 555 AAA 555 AAA 555 AAA 555 AA Data RD F0 AA AA 2AA 555 2AA 555 2AA 555 2AA 55 55 55 555 AAA 555 AAA 555 AAA 555 90 90 90 X00 X01 X02 X03 X06 (SA)X02 (SA)X04 99/19 01 (see Table 6) Am29LV320D Command Definitions Bus Cycles (Notes 2–5) Second Addr Data Third Addr Data Fourth Addr Data Fifth Addr Data Sixth Addr Data 1 1 4 4 Byte Word Byte Word Byte Word Byte Word Byte 4 3 4 4 AAA 555 AAA 555 AAA 555 AAA 555 AAA XXX XXX 555 AAA 555 AAA XXX XXX 55 AA AA AA AA AA AA A0 90 AA AA B0 30 98 555 2AA 555 2AA 555 2AA 555 2AA 555 PA XXX 2AA 555 2AA 555 55 55 55 55 55 PD 00 55 55 AAA 555 AAA 555 AAA 555 AAA 555 AAA 90 88 90 A0 20 00/01 Enter Secured Silicon Sector Exit Secured Silicon Sector Program Unlock Bypass XXX PA 00 PD 3 2 2 6 6 1 1 Unlock Bypass Program (Note 11) Unlock Bypass Reset (Note 12) Chip Erase Sector Erase Erase Suspend (Note 13) Erase Resume (Note 14) CFI Query (Note 15) Word Byte Word Byte Word Byte 555 AAA 555 AAA 80 80 555 AAA 555 AAA AA AA 2AA 555 2AA 555 55 55 555 AAA SA 10 30 1 Legend: X = Don’t care RA = Address of the memory location to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. Notes: 1. See Table 1 for description of bus operations. 2. All values are in hexadecimal. 3. 4. 5. 6. 7. Except for the read cycle and the fourth cycle of the autoselect command sequence, all bus cycles are write cycles. Data bits DQ15–DQ8 are don’t care in command sequences, except for RD and PD. Unless otherwise noted, address bits A20–A11 are don’t cares. No unlock or command cycles required when device is in read mode. The Reset command is required to return to the read mode (or to the erase-suspend-read mode if previously in Erase Suspend) when a device is in the autoselect mode, or if DQ5 goes high (while the device is providing status information). The fourth cycle of the autoselect command sequence is a read cycle. Data bits DQ15–DQ8 are don’t care. See the Autoselect Command Sequence section for more information. PD = Data to be programmed at location PA. Data latches on the rising edge of WE# or CE# pulse, whichever happens first. SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A20–A12 uniquely select any sector. 9. The data is 99h for factory locked and 19h for not factory locked. 10. The data is 00h for an unprotected sector and 01h for a protected sector. 11. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 12. The Unlock Bypass Reset command is required to return to the read mode when the device is in the unlock bypass mode. 13. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 14. The Erase Resume command is valid only during the Erase Suspend mode. 15. Command is valid when device is ready to read array data or when device is in autoselect mode. 8. December 14, 2005 Am29LV320D 29 DATASHEET WRITE OPERATION STATUS The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 15 on page 33 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to determine whether an Embedded Program or Erase operation is in progress or is completed. the program or erase operation and DQ7 contains valid data, the data outputs on DQ0–DQ6 may be still invalid. Valid data on DQ0–DQ7 appears on successive read cycles. Table 15 on page 33 shows the outputs for Data# Polling on DQ7. Figure 6, on page 30 shows the Data# Polling algorithm. Figure 20, on page 44 in the AC Characteristics section shows the Data# Polling timing diagram. DQ7: Data# Polling The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether a device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then the device returns to the read mode. During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the device returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device completes START Read DQ7–DQ0 Addr = VA DQ7 = Data? Yes No No DQ5 = 1? Yes Read DQ7–DQ0 Addr = VA DQ7 = Data? Yes No FAIL PASS Notes: 1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being erased. During chip erase, a valid address is any non-protected sector address. 2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5. Figure 6. Data# Polling Algorithm 30 Am29LV320D December 14, 2005 DATASHEET RY/BY#: Ready/Busy# The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is in the read mode, the standby mode, or in the erase-suspend-read mode. Table 15 on page 33 shows the outputs for RY/BY#. gorithm. Figure 21, on page 45 in the “AC Characteristics” section shows the toggle bit timing diagrams. Figure 22, on page 45 shows the differences between DQ2 and DQ6 in graphical form. See also the subsection on DQ2: Toggle Bit II. START Read DQ7–DQ0 DQ6: Toggle Bit I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is complete, DQ6 stops toggling. After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on “DQ7: Data# Polling” on page 30). If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete. Table 15 on page 33 shows the outputs for Toggle Bit I on DQ6. Figure 7, on page 31 shows the toggle bit al- Read DQ7–DQ0 Toggle Bit = Toggle? Yes No No DQ5 = 1? Yes Read DQ7–DQ0 Twice Toggle Bit = Toggle? No Yes Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete Note: The system should recheck the toggle bit even if DQ5 = “1” because the toggle bit may stop toggling as DQ5 changes to “1.” See the subsections on DQ6 and DQ2 for more information. Figure 7. Toggle Bit Algorithm DQ2: Toggle Bit II The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), 31 December 14, 2005 Am29LV320D DATASHEET or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that were selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 15 on page 33 to compare outputs for DQ2 and DQ6. Figure 7, on page 31 shows the toggle bit algorithm in flowchart form, and the section “DQ2: Toggle Bit II” on page 31 explains the algorithm. See also the DQ6: Toggle Bit I subsection. Figure 21, on page 45 shows the toggle bit timing diagram. Figure 22, on page 45 shows the differences between DQ2 and DQ6 in graphical form. DQ5: Exceeded Timing Limits DQ5 indicates whether the program or erase time exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase cycle was not successfully completed. The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was previously programmed to “0.” O nly an erase operation can change a “0” back to a “1.” Under this condition, the device halts the operation, and when the timing limit is exceeded, DQ5 produces a “1.” Under both these conditions, the system must write the reset command to return to the read mode (or to the erase-suspend-read mode if the device was previously in the erase-suspend-program mode). DQ3: Sector Erase Timer After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure started. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be assumed to be less than 50 µs, the system need not monitor DQ3. See also the Sector Erase Command Sequence section. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device accepted the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase algorithm started; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device accepts additional sector erase commands. To ensure the command is accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 15 on page 33 shows the status of DQ3 relative to the other status bits. Reading Toggle Bits DQ6/DQ2 Refer to Figure 7, on page 31 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device completed the program or erase operation. The system can read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 7, on page 31). 32 Am29LV320D December 14, 2005 DATASHEET Table 15. Status Embedded Program Algorithm Embedded Erase Algorithm Erase Erase-Suspend- Suspended Sector Read Non-Erase Suspended Sector Erase-Suspend-Program Write Operation Status DQ7 (Note 2) DQ7# 0 1 Data DQ7# DQ6 Toggle Toggle No toggle Data Toggle DQ5 (Note 1) 0 0 0 Data 0 DQ3 N/A 1 N/A Data N/A DQ2 (Note 2) No toggle Toggle Toggle Data N/A RY/BY# 0 0 1 1 0 Standard Mode Erase Suspend Mode Notes: 1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation exceeds the maximum timing limits. Refer to the section on DQ5 for more information. 2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. December 14, 2005 Am29LV320D 33 DATASHEET ABSOLUTE MAXIMUM RATINGS Storage Temperature Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C Ambient Temperature with Power Applied. . . . . . . . . . . . . . –65°C to +125°C Voltage with Respect to Ground Notes: 1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may overshoot V SS t o –2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. See Figure 8, on page 34. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 9, on page 34. 2. Minimum DC input voltage on pins A9, OE#, RESET#, and WP#/ACC is –0.5 V. During voltage transitions, A9, OE#, WP#/ACC, and RESET# may overshoot V SS t o –2.0 V for periods of up to 20 ns. See Figure 8, on page 34. Maximum DC input voltage on pin A9 is +12.5 V which may overshoot to +14.0 V for periods up to 20 ns. Maximum DC input voltage on WP#/ACC is +9.5 V which may overshoot to +12.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. VCC+2.0 V VCC+0.5 V 2.0 V 20 ns 20 ns VCC (Note 1). . . . . . . . . . . . . . . . . –0.5 V to +4.0 V A9, OE#, RESET#, and WP#/ACC (Note 2) . . . . . . . –0.5 V to +12.5 V All other pins (Note 1) . . . . . . –0.5 V to VCC +0.5 V Output Short Circuit Current (Note 3) . . . . . . . 200 mA 20 ns +0.8 V VSS–0.5 V VSS–2.0 V 20 ns 20 ns Figure 8. Maximum Negative Overshoot Waveform 20 ns Figure 9. Maximum Positive Overshoot Waveform OPERATING RANGES Industrial (I) Devices Ambient Temperature (TA) . . . . . . . . . –40°C to +85°C VCC Supply Voltages VCC for all devices . . . . . . . . . . . . . . . . . 2.7 V to 3.6 V Operating ranges define those limits between which the functionality of the device is guaranteed. 34 Am29LV320D December 14, 2005 DATASHEET DC CHARACTERISTICS CMOS Compatible Parameter Symbol ILI ILIT ILR ILO Parameter Description Input Load Current A9 Input Load Current RESET# Input Load Current Output Leakage Current Test Conditions VIN = VSS to VCC, VCC = VCC max VCC = VCC max; A9 = 12.5 V VCC = VCC max; RESET# = 12.5 V VOUT = VSS to VCC, VCC = VCC max CE# = VIL, OE# = VIH, Byte Mode CE# = VIL, OE# = VIH, Word Mode 5 MHz 1 MHz 5 MHz 1 MHz 10 2 10 2 15 0.2 0.2 0.2 –0.5 0.7 x VCC VCC = 3.0 V ± 10% 11.5 Min Typ Max ±3.0 35 35 ±1.0 16 4 16 4 30 5 5 5 0.8 VCC + 0.3 12.5 mA µA µA µA V V V mA Unit µA µA µA µA ICC1 VCC Active Read Current (Notes 1, 2) ICC2 ICC3 ICC4 ICC5 VIL VIH VHH VCC Active Write Current (Notes 2, 3) CE# = VIL, OE# = VIH, WE# = VIL VCC Standby Current (Note 2) VCC Reset Current (Note 2) Automatic Sleep Mode (Notes 2, 4) Input Low Voltage Input High Voltage Voltage for WP#/ACC Sector Protect/Unprotect and Program Acceleration CE#, RESET# = VCC ± 0.3 V RESET# = VSS ± 0.3 V VIH = VCC ± 0.3 V; VIL = VSS ± 0.3 V VID VOL VOH1 VOH2 VLKO Voltage for Autoselect and Temporary VCC = 3.0 V ± 10% Sector Unprotect Output Low Voltage Output High Voltage Low VCC Lock-Out Voltage (Note 5) IOL = 4.0 mA, VCC = VCC min IOH = –2.0 mA, VCC = VCC min IOH = –100 µA, VCC = VCC min 11.5 12.5 0.45 V V V 0.85 VCC VCC–0.4 2.3 2.5 V Notes: 1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. 2. Maximum ICC specifications are tested with VCC = VCCmax. 3. ICC active while Embedded Erase or Embedded Program is in progress. 4. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. Typical sleep mode current is 200 nA. 5. Not 100% tested. December 14, 2005 Am29LV320D 35 DATASHEET DC CHARACTERISTICS Zero-Power Flash 25 Supply Current in mA 20 15 10 5 0 0 500 1000 1500 2000 Time in ns 2500 3000 3500 4000 Note: Addresses are switching at 1 MHz Figure 10. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents) 12 3.6 V 10 2.7 V 8 Supply Current in mA 6 4 2 0 1 Note: T = 25 °C 2 3 Frequency in MHz Figure 11. Typical ICC1 vs. Frequency 4 5 36 Am29LV320D December 14, 2005 DATASHEET TEST CONDITIONS Table 16. 3.3 V 2.7 kΩ Test Condition Output Load Output Load Capacitance, CL (including jig capacitance) CL 6.2 kΩ Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels Note: Diodes are IN3064 or equivalent Output timing measurement reference levels 30 5 0.0–3.0 1.5 1.5 Test Specifications 90 120 1 TTL gate 100 pF ns V V V Unit Device Under Test Figure 12. Test Setup Key To Switching Waveforms WAVEFORM INPUTS Steady Changing from H to L Changing from L to H Don’t Care, Any Change Permitted Does Not Apply Changing, State Unknown Center Line is High Impedance State (High Z) OUTPUTS 3.0 V 0.0 V Input 1.5 V Measurement Level 1.5 V Output Figure 13. Input Waveforms and Measurement Levels December 14, 2005 Am29LV320D 37 DATASHEET AC CHARACTERISTICS Read-Only Operations Parameter JEDEC tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX Std. tRC tACC tCE tOE tDF tDF tOH Description Read Cycle Time (Note 1) Address to Output Delay Chip Enable to Output Delay Output Enable to Output Delay Chip Enable to Output High Z (Note 1) Output Enable to Output High Z (Note 1) Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First Read tOEH Output Enable Hold Time (Note 1) Toggle and Data# Polling CE#, OE# = VIL OE# = VIL Test Setup Min Max Max Max Max Max Min Min Min Speed Options 90 90 90 90 40 16 16 0 0 10 120 120 120 120 50 Unit ns ns ns ns ns ns ns ns ns Notes: 1. Not 100% tested. 2. See Figure 12, on page 37 and Table 16 on page 37 for test specifications. tRC Addresses CE# tRH tRH OE# tOEH WE# HIGH Z Outputs RESET# RY/BY# Output Valid tCE tOH HIGH Z tOE tDF Addresses Stable tACC 0V Figure 14. Read Operation Timings 38 Am29LV320D December 14, 2005 DATASHEET AC CHARACTERISTICS Hardware Reset (RESET#) Parameter JEDEC Std tReady tReady tRP tRH tRPD tRB Description RESET# Pin Low (During Embedded Algorithms) to Read Mode (See Note) RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode (See Note) RESET# Pulse Width Reset High Time Before Read (See Note) RESET# Low to Standby Mode RY/BY# Recovery Time Max Max Min Min Min Min All Speed Options 20 500 500 50 20 0 Unit µs ns ns ns µs ns Note: Not 100% tested. RY/BY# CE#, OE# tRH RESET# tRP tReady Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms tReady RY/BY# tRB CE#, OE# tRH RESET# tRP Figure 15. Reset Timings December 14, 2005 Am29LV320D 39 DATASHEET AC CHARACTERISTICS Word/Byte Configuration (BYTE#) Parameter JEDEC Std. tELFL/tELFH tFLQZ tFHQV Description CE# to BYTE# Switching Low or High BYTE# Switching Low to Output HIGH Z BYTE# Switching High to Output Active Max Max Min 90 90 5 16 120 120 Unit ns ns ns CE# OE# BYTE# tELFL DQ0–DQ14 BYTE# Switching from word to byte mode Data Output (DQ0–DQ14) Data Output (DQ0–DQ7) Address Input DQ15/A-1 DQ15 Output tFLQZ tELFH BYTE# BYTE# Switching from byte to word mode DQ0–DQ14 Data Output (DQ0–DQ7) Address Input tFHQV Data Output (DQ0–DQ14) DQ15 Output DQ15/A-1 Figure 16. BYTE# Timings for Read Operations CE# The falling edge of the last WE# signal WE# BYTE# tSET (tAS) tHOLD (tAH) Note: Refer to the Erase/Program Operations table for tAS and tAH specifications. Figure 17. BYTE# Timings for Write Operations 40 Am29LV320D December 14, 2005 DATASHEET AC CHARACTERISTICS Erase and Program Operations Parameter JEDEC tAVAV tAVWL Std. tWC tAS tASO tWLAX tAH tAHT tDVWH tWHDX tDS tDH tOEPH tGHWL tELWL tWHEH tWLWH tWHDL tGHWL tCS tCH tWP tWPH tSR/W tWHWH1 tWHWH1 Description Write Cycle Time (Note 1) Address Setup Time Address Setup Time to OE# low during toggle bit polling Address Hold Time Address Hold Time From CE# or OE# high during toggle bit polling Data Setup Time Data Hold Time Output Enable High during toggle bit polling Read Recovery Time Before Write (OE# High to WE# Low) CE# Setup Time CE# Hold Time Write Pulse Width Write Pulse Width High Latency Between Read and Write Operations Byte Programming Operation (Note 2) Word Accelerated Programming Operation, Word or Byte (Note 2) Sector Erase Operation (Note 2) VCC Setup Time (Note 1) Write Recovery Time from RY/BY# Program/Erase Valid to RY/BY# Delay Typ Typ Typ Min Min Max 11 7 0.7 50 0 90 µs sec µs ns ns Min Min Min Min Min Min Min Min Min Min Min Min Min Min Typ 35 30 0 9 µs 45 0 20 0 0 0 50 45 0 50 90 90 0 15 50 120 120 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns tWHWH1 tWHWH2 tWHWH1 tWHWH2 tVCS tRB tBUSY Notes: 1. Not 100% tested. 2. See “Erase And Programming Performance” on page 50 for more information. December 14, 2005 Am29LV320D 41 DATASHEET AC CHARACTERISTICS Program Command Sequence (last two cycles) tAS tWC Addresses 555h PA tAH CE# OE# tWP WE# tCS tDS Data tDH PD tBUSY RY/BY# tVCS VCC Status DOUT tRB tWPH tWHWH1 Read Status Data (last two cycles) PA PA tCH A0h Notes: 1. PA = program address, PD = program data, DOUT is the true data at the program address. 2. Illustration shows device in word mode. Figure 18. Program Operation Timings 42 Am29LV320D December 14, 2005 DATASHEET AC CHARACTERISTICS Erase Command Sequence (last two cycles) tWC Addresses 2AAh tAS SA 555h for chip erase Read Status Data VA tAH VA CE# OE# tWP WE# tCS tDS tCH tWPH tWHWH2 tDH Data 55h 30h 10 for Chip Erase In Progress Complete tBUSY RY/BY# tVCS VCC tRB Notes: 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status” on page 30). 2. These waveforms are for the word mode. Figure 19. Chip/Sector Erase Operation Timings December 14, 2005 Am29LV320D 43 DATASHEET AC CHARACTERISTICS tRC Addresses VA tACC tCE CE# tCH OE# tOEH WE# tOH DQ7 High Z VA VA tOE tDF Complement Complement True Valid Data High Z DQ0–DQ6 tBUSY RY/BY# Status Data Status Data True Valid Data Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle. Figure 20. Data# Polling Timings (During Embedded Algorithms) 44 Am29LV320D December 14, 2005 DATASHEET AC CHARACTERISTICS tAHT Addresses tAHT tASO CE# tOEH WE# tOEPH OE# tDH DQ6/DQ2 Valid Data Valid Status tAS tCEPH tOE Valid Status Valid Status Valid Data (first read) RY/BY# (second read) (stops toggling) Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle Figure 21. Toggle Bit Timings (During Embedded Algorithms) Enter Embedded Erasing WE# Erase Suspend Erase Enter Erase Suspend Program Erase Suspend Program Erase Resume Erase Suspend Read Erase Erase Complete Erase Suspend Read DQ6 DQ2 Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle DQ2 and DQ6. Figure 22. DQ2 vs. DQ6 December 14, 2005 Am29LV320D 45 DATASHEET AC CHARACTERISTICS Temporary Sector Unprotect Parameter JEDEC Std. tVIDR tVHH tRSP tRRB Description VID Rise and Fall Time (See Note) VHH Rise and Fall Time (See Note) RESET# Setup Time for Temporary Sector Unprotect RESET# Hold Time from RY/BY# High for Temporary Sector Unprotect Min Min Min Min All Speed Options 500 250 4 4 Unit ns ns µs µs Note: Not 100% tested. VID RESET# VSS, VIL, or VIH tVIDR Program or Erase Command Sequence CE# tVIDR VID VSS, VIL, or VIH WE# tRSP RY/BY# tRRB Figure 23. Temporary Sector Unprotect Timing Diagram VHH WP#/ACC VIL or VIH tVHH tVHH VIL or VIH Figure 24. Accelerated Program Timing Diagram 46 Am29LV320D December 14, 2005 DATASHEET AC CHARACTERISTICS VID VIH RESET# SA, A6, A1, A0 Valid* Sector/Sector Block Protect or Unprotect Valid* Verify 40h Sector/Sector Block Protect: 150 µs, Sector/Sector Block Unprotect: 15 ms Valid* Data 60h 60h Status 1 µs CE# WE# OE# * For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0. Figure 25. Sector/Sector Block Protect and Unprotect Timing Diagram December 14, 2005 Am29LV320D 47 DATASHEET AC CHARACTERISTICS Alternate CE# Controlled Erase and Program Operations Parameter JEDEC tAVAV tAVWL tELAX tDVEH tEHDX tGHEL tWLEL tEHWH tELEH tEHEL tWHWH1 Std. tWC tAS tAH tDS tDH tGHEL tWS tWH tCP tCPH tWHWH1 Description Write Cycle Time (Note 1) Address Setup Time Address Hold Time Data Setup Time Data Hold Time Read Recovery Time Before Write (OE# High to WE# Low) WE# Setup Time WE# Hold Time CE# Pulse Width CE# Pulse Width High Programming Operation (Note 2) Accelerated Programming Operation, Word or Byte (Note 2) Sector Erase Operation (Note 2) Byte Word Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Typ 45 30 9 µs 11 7 0.7 µs sec 45 45 0 0 0 0 50 90 90 0 50 50 120 120 Unit ns ns ns ns ns ns ns ns ns ns tWHWH1 tWHWH2 tWHWH1 tWHWH2 Notes: 1. Not 100% tested. 2. See “Erase And Programming Performance” on page 50 for more information. 48 Am29LV320D December 14, 2005 DATASHEET AC CHARACTERISTICS 555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase Data# Polling PA Addresses tWC tWH WE# tGHEL OE# tCP CE# tWS tCPH tDS tDH Data tRH A0 for program 55 for erase PD for program 30 for sector erase 10 for chip erase tAS tAH tWHWH1 or 2 tBUSY DQ7# DOUT RESET# RY/BY# Notes: 1. Figure indicates last two bus cycles of a program or erase operation. 2. PA = program address, SA = sector address, PD = program data. 3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device. 4. Waveforms are for the word mode. Figure 26. Alternate CE# Controlled Write (Erase/Program) Operation Timings December 14, 2005 Am29LV320D 49 DATASHEET ERASE AND PROGRAMMING PERFORMANCE Parameter Sector Erase Time Chip Erase Time Byte Program Time Word Program Time Accelerated Byte/Word Program Time Chip Program Time (Note 3) Byte Mode Word Mode Typ (Note 1) 0.7 50 9 11 7 36 24 300 360 210 108 sec 72 Max (Note 2) 15 Unit sec sec µs µs µs Excludes system level overhead (Note 5) Comments Excludes 00h programming prior to erasure (Note 4) Notes: 1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 1,000,000 cycles. Additionally, programming typicals assume checkerboard pattern. 2. Under worst case conditions of 90°C, VCC = 2.7 V, 4. In the pre-programming step of the Embedded Erase 1,000,000 cycles. algorithm, all bytes are programmed to 00h before erasure. 3. The typical chip programming time is considerably less than 5. System-level overhead is the time required to execute the the maximum chip programming time listed, since most two- or four-bus-cycle sequence for the program command. bytes program faster than the maximum program times See Table 14 on page 29 for further information on listed. command definitions. 6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles. LATCHUP CHARACTERISTICS Description Input voltage with respect to VSS on all pins except I/O pins (including A9, OE#, and RESET#) Input voltage with respect to VSS on all I/O pins VCC Current Min –1.0 V –1.0 V –100 mA Max 12.5 V VCC + 1.0 V +100 mA Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time. TSOP AND BGA PACKAGE CAPACITANCE Parameter Symbol CIN COUT CIN2 Notes: 1. Sampled, not 100% tested. 2. Test conditions TA = 25°C, f = 1.0 MHz. Parameter Description Input Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 TSOP Fine-pitch BGA TSOP Fine-pitch BGA TSOP Fine-pitch BGA Typ 6 4.2 8.5 5.4 7.5 3.9 Max 7.5 5.0 12 6.5 9 4.7 Unit pF pF pF pF pF pF Output Capacitance Control Pin Capacitance DATA RETENTION Parameter Description Minimum Pattern Data Retention Time Test Conditions 150°C 125°C Min 10 20 Unit Years Years 50 Am29LV320D December 14, 2005 DATASHEET PHYSICAL DIMENSIONS FBD048—48-ball Fine-Pitch Ball Grid Array (FBGA) 6 x 12 mm package Dwg rev AF; 1/2000 xFBD 048 6.00 mm x 12.00 mm PACKAGE 1.20 0.20 0.94 0.84 12.00 BSC 6.00 BSC 5.60 BSC 4.00 BSC 8 6 48 0.25 0.30 0.35 0.80 BSC 0.40 BSC December 14, 2005 Am29LV320D 51 DATASHEET PHYSICAL DIMENSIONS TS 048—48-Pin Standard TSOP Dwg rev AA; 10/99 52 Am29LV320D December 14, 2005 DATASHEET REVISION SUMMARY Revision A (November 1, 2000) Initial release. Erase and Program Operations table Corrected to indicate tBUSY specification is a maximum value. Revision A+1 (January 23, 2001) Ordering Information Corrected FBGA part number table to include bottom boot part numbers. Revision B+1 (July 30, 2002) Figure 3, Secured Silicon Sector Protect Verify Deleted fifth block in flowchart and modified text in fourth block. Revision A+2 (February 1, 2001) Connection Diagrams Corrected FBGA ball matrix. Revision C (October 25, 2002) Distinctive Characteristics Changed endurance from “write” to “erase” cycles. Connection Diagrams Deleted ultrasonic reference and added package types to special package handling text. Ordering Information Added commercial temperature range and removed extended temperature range. Secured Silicon Flash Memory Region Customer Lockable subsection: Deleted reference to alternate method of sector protection. Command Definitions Noted the following: Autoselect, Secured Silicon, and CFI functions are not available during a program or erase operation. ACC and unlock bypass modes are not available when the Secured Silicon Sector is enabled. Writing incorrect data or commands may place the device in an unknown state. A reset command is then required. AC Characteristics Read-only Operations; Word/Byte Configuration: Changed tDF and tFLQZ to 16 ns for all speed options. DC Characteristics Deleted IACC and added ILR specifications from table. TSOP, SO, and BGA Package Capacitance Added BGA capacitance to table. Revision A+3 (July 2, 2001) Global Changed data sheet status from Advance Information to Preliminary. Table 3, Top Boot Secured Silicon Sector Addresses Corrected sector block size for SA60–SA62 to 3x64. Sector/Sector Block Protection and Unprotection Noted that sectors are erased in parallel. Secured Silicon Sector Flash Memory Region Noted changes for upcoming versions of these devices: reduced Secured Silicons ector size, different ESN location for top boot devices, and deletion of Secured Silicon erase functionality. Current versions of these devices remain unaffected. Revision B (July 12, 2002) Global Deleted Preliminary status from document. Ordering Information Deleted burn-in option. Table 1, Am29LV320D Device Bus Operations In the legend, corrected VHH maximum voltage to 12.5 V. Secured Silicon Sector Flash Memory Region Added description of Secured Silicon protection verification. Autoselect Command Sequence Clarified description of function. Table 14, Am29LV320D Command Definitions Corrected autoselect codes for Secured Silicon Factory Protect. Revision C+1 (February 16, 2003) Distinctive Characteristics Added reference to MirrorBit in Secured Silicon section. Added Sector Architecture section. Secured Silicon Flash Memory Region Referenced MirrorBit for an example in last sentence of first paragraph. December 14, 2005 Am29LV320D 53 DATASHEET Command Definitions Changed the first address of the Unlock Bypass Reset from BA to XXX. Erase and Programming Performance Corrected the Sector Erase Time Typical to 0.7. Erase and Programming Performance Updated Chip Erase Time. AC Characteristics Added tRH line to Figure 15. Erase and Program Operations t Corrected Sector Erase Operation time ( WHWH2) Revision C+2 (April 4, 2003) Distinctive Characteristics Clarified reference to MirrorBit in Secured Silicon section. Secured Silicon Sector Clarified reference of MirrorBit for an example in last sentence of first paragraph. Alternate CE# Control Erase and Program Operations t Corrected Sector Erase Operation time ( WHWH2) Command Definitions Update text in Sector Erase Command Sequence paragraph. Revision C+3 (September 19, 2003) Valid Combinations Added the 90R package to table. Revision C+7 (July 11, 2005) Global Added text to first page of data sheet and cover page indicating that the Am29LV320D is now superceded by the S29AL032D device. Replaced all occurences of “SecSi Sector” with “Secured Silicon Sector” to reflect change of terminology. Common Flash Memory Interfacte (CFI) Added reference to application note. Deleted link to CFI documents available on the world wide web. Revision C+4 (April 5, 2004) Command Definitions Changed first address data for Erase Suspend/Resume from BA to XXX. Revision C+5 (June 4, 2004) Ordering Information Added Lead-free (Pb-free) options to the temperature ranges breakout table and valid combinations table. Product Selector Guide Added 90R voltage range. Revision C+8 (December 14, 2005) Global This product has been retired and is not available for designs. For new and current designs, S29AL032D supersedes Am29LV320D and is the factory-recomm e n d e d m i g r a t i o n p a t h . P l e a s e r e fe r t o t h e S29AL032D datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only. Revision C+6 (November 15, 2004) Global Added Colophon. Updated Trademarks. Added reference links Ordering Information Added Automotive In-Cabin temperature range and associated part numbers in the valid combination table. 54 Am29LV320D December 14, 2005 DATASHEET Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion LLC will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks Copyright © 2000-2005 Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc. ExpressFlash is a trademark of Advanced Micro Devices, Inc. Product names used in this publication are for identification purposes only and may be trademarks of their respective companies. December 14, 2005 Am29LV320D 55