AM42DL3224GB30IT

PRELIMINARY Am42DL32x4G Stacked Multi-Chip Package (MCP) Flash Memory and SRAM 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory and 4 Mbit (256 K x 16-Bit) Static RAM DISTINCTIVE CHARACTERISTICS MCP Features ■ Power supply voltage of 2.7 to 3.3 volt ■ High performance — Flash Access time as fast as 70 ns — SRAM access time as fast as 55 ns SOFTWARE FEATURES ■ Data Management Software (DMS) — AMD-supplied software manages data programming and erasing, enabling EEPROM emulation — Eases sector erase limitations ■ Package — 73-Ball FBGA ■ Supports Common Flash Memory Interface (CFI) ■ Erase Suspend/Erase Resume — Suspends erase operations to allow programming in same bank ■ Operating Temperature — –40°C to +85°C ■ Data# Polling and Toggle Bits — Provides a software method of detecting the status of program or erase cycles Flash Memory Features ARCHITECTURAL ADVANTAGES ■ Simultaneous Read/Write operations — Data can be continuously read from one bank while executing erase/program functions in other bank — Zero latency between read and write operations ■ Unlock Bypass Program command — Reduces overall programming time when issuing multiple program command sequences HARDWARE FEATURES ■ Any combination of sectors can be erased ■ Ready/Busy# output (RY/BY#) — Hardware method for detecting program or erase cycle completion ■ Secured Silicon (SecSi) Sector: Extra 256 Byte sector — Factory locked and identifiable: 16 bytes available for secure, random factory Electronic Serial Number; verifiable as factory locked through autoselect function. — Customer lockable: Sector is one-time programmable. Once locked, data cannot be changed ■ Hardware reset pin (RESET#) — Hardware method of resetting the internal state machine to reading array data ■ Zero Power Operation — Sophisticated power management circuits reduce power consumed during inactive periods to nearly zero ■ WP#/ACC input pin — Write protect (WP#) function allows protection of two outermost boot sectors, regardless of sector protect status — Acceleration (ACC) function accelerates program timing ■ Top or bottom boot block ■ Manufactured on 0.17 µm process technology ■ Compatible with JEDEC standards — Pinout and software compatible with single-power-supply flash standard ■ Sector protection — Hardware method of locking a sector, either in-system or using programming equipment, to prevent any program or erase operation within that sector — Temporary Sector Unprotect allows changing data in protected sectors in-system PERFORMANCE CHARACTERISTICS ■ High performance — Access time as fast as 70 ns — Program time: 4 µs/word typical utilizing Accelerate function SRAM Features ■ Power dissipation — Operating: 22 mA maximum for 70 ns, 30 mA maximum for 55 ns — Standby: 10 µA maximum ■ Ultra low power consumption (typical values) — 2 mA active read current at 1 MHz — 10 mA active read current at 5 MHz — 200 nA in standby or automatic sleep mode ■ Minimum 1 million write cycles guaranteed per sector ■ 20 Year data retention at 125°C — Reliable operation for the life of the system ■ ■ ■ ■ CE1s# and CE2s Chip Select Power down features using CE1s# and CE2s Data retention supply voltage: 1.5 to 3.3 volt Byte data control: LB#s (DQ7–DQ0), UB#s (DQ15–DQ8) This document contains information on a product under development at Advanced Micro Devices. The information is intended to help you evaluate this product. AMD reserves the right to change or discontinue work on this proposed product without notice. Publication# 25822 Rev: B Amendment/0 Issue Date: May 19, 2003 Refer to AMD’s Website (www.amd.com) for the latest information. PRELIMINARY GENERAL DESCRIPTION Am29DL32xG Features The Am29DL322G/323G/324G consists of 32 megabit, 3.0 volt-only flash memory devices, organized as 2,097,152 words of 16 bits each or 4,194,304 bytes of 8 bits each. Word mode data appears on DQ15–DQ0; byte mode data appears on DQ7–DQ0. The device is designed to be programmed in-system with the standard 3.0 volt VCC supply, and can also be programmed in standard EPROM programmers. The devices are available with access times of 85 and 70 ns. The device is offered in a 73-ball FBGA package. Standard control pins—chip enable (CE#f), write enable (WE#), and output enable (OE#)—control normal read and write operations, and avoid bus contention issues. The devices requires only a single 3.0 volt power supply for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. DMS (Data Management Software) allows systems to easily take advantage of the advanced architecture of the simultaneous read/write product line by allowing removal of EEPROM devices. DMS will also allow the system software to be simplified, as it will perform all functions necessary to modify data in file structures, as opposed to single-byte modifications. To write or update a particular piece of data (a phone number or configuration data, for example), the user only needs to state which piece of data is to be updated, and where the updated data is located in the system. This is a n a d va n t a g e co m p a r e d t o sys t e ms w h e r e user-written software must keep track of the old data location, status, logical to physical translation of the data onto the Flash memory device (or memory devices), and more. Using DMS, user-written software does not need to interface with the Flash memory directly. Instead, the user's software accesses the Flash memory by calling one of only six functions. AMD provides this software to simplify system design and software integration efforts. The device offers complete compatibility with the JEDEC single-power-supply Flash command set standard . Commands are written to the command register using standard microprocessor write timings. Reading data out of the device is similar to reading from other Flash or EPROM devices. The host system can detect whether a program or erase operation is complete by using the device status bits: R Y/BY# pin, DQ7 (Data# Polling) and DQ6/DQ2 (toggle bits). After a program or erase cycle has been completed, the device automatically returns to reading array data. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of the sectors of memo r y. T h i s c a n b e a c h i e v e d i n - s y s t e m o r v i a programming equipment. The device offers two power-saving features. When addresses have been stable for a specified amount of time, the device enters the automatic sleep mode. The system can also place the device into the standby mode . Power consumption is greatly reduced in both modes. Simultaneous Read/Write Operations with Zero Latency The Simultaneous Read/Write architecture provides simultaneous operation b y dividing the memory space into two banks. The device can improve overall system performance by allowing a host system to program or erase in one bank, then immediately and simultaneously read from the other bank, with zero latency. This releases the system from waiting for the completion of program or erase operations. The Am29DL32xG device family uses multiple bank architectures to provide flexibility for different applications. Three devices are available with the following bank sizes: Device DL322 DL323 DL324 Bank 1 4 8 16 Bank 2 28 24 16 The Secured Silicon (SecSi) Sector is an extra 256 byte sector capable of being permanently locked by AMD or customers. The SecSi Sector Indicator Bit (DQ7) is permanently set to a 1 if the part is factory locked , and set to a 0 if c ustomer lockable . This way, customer lockable parts can never be used to replace a factory locked part. F actory locked parts provide several options. The SecSi Sector may store a secure, random 16 byte ESN (Electronic Serial Number). Customer Lockable devices are one-time programmable and one-time lockable. 2 Am42DL32x4G May 19, 2003 PRELIMINARY TABLE OF CONTENTS Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 5 MCP Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . 5 Flash Memory Block Diagram. . . . . . . . . . . . . . . . 6 Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . 7 Special Handling Instructions for FBGA Package .................... 7 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 9 Device Bus Operations . . . . . . . . . . . . . . . . . . . . 10 Table 2. Device Bus Operations—Flash Byte Mode, CIOf = VSS ....12 Figure 6. Toggle Bit Algorithm........................................................ 34 DQ2: Toggle Bit II ................................................................... 35 Reading Toggle Bits DQ6/DQ2 ............................................... 35 DQ5: Exceeded Timing Limits ................................................ 35 DQ3: Sector Erase Timer ....................................................... 35 Table 18. Write Operation Status ................................................... 36 Requirements for Reading Array Data ................................... 13 Writing Commands/Command Sequences ............................ 13 Accelerated Program Operation ............................................. 13 Autoselect Functions .............................................................. 13 Simultaneous Read/Write Operations with Zero Latency ....... 13 Automatic Sleep Mode ........................................................... 14 RESET#: Hardware Reset Pin ............................................... 14 Output Disable Mode .............................................................. 14 Table 3. Device Bank Division ........................................................14 Table 4. Top Boot Sector Addresses .............................................15 Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 37 Industrial (I) Devices ............................................................... 37 VCCf/VCCs Supply Voltage ....................................................... 37 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 38 CMOS Compatible .................................................................. 38 SRAM DC and Operating Characteristics. . . . . . 39 Zero-Power Flash ................................................................. 40 Figure 9. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents) ........................................................................................ 40 Figure 10. Typical ICC1 vs. Frequency............................................ 40 Test Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Figure 11. Test Setup.................................................................... 41 Table 19. Test Specifications ......................................................... 41 Sector/Sector Block Protection and Unprotection .................. 19 Table 8. Top Boot Sector/Sector Block Addresses for Protection/Unprotection .............................................................19 Table 9. Bottom Boot Sector/Sector Block Addresses for Protection/Unprotection .............................................................20 Key To Switching Waveforms . . . . . . . . . . . . . . . 41 Figure 12. Input Waveforms and Measurement Levels ................. 41 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 42 SRAM CE#s Timing ................................................................ 42 Figure 13. Timing Diagram for Alternating Between SRAM to Flash .. 42 Write Protect (WP#) ................................................................ 20 Temporary Sector/Sector Block Unprotect ............................. 20 Figure 1. Temporary Sector Unprotect Operation........................... 21 Figure 1. In-System Sector/Sector Block Protect and Unprotect Algorithms ....................................................................................... 22 Flash Read-Only Operations ................................................. 43 Figure 14. Read Operation Timings............................................... 43 Hardware Reset (RESET#) .................................................... 44 Figure 15. Reset Timings ............................................................... 44 SecSi (Secured Silicon) Sector Flash Memory Region .......... 23 Factory Locked: SecSi Sector Programmed and Protected At the Factory .................................................................................... 23 Customer Lockable: SecSi Sector NOT Programmed or Protected At the Factory ......................................................... 23 Figure 2. SecSi Sector Protect Verify.............................................. 23 Flash Word/Byte Configuration (CIOf) .................................... 45 Figure 16. CIOf Timings for Read Operations................................ 45 Figure 17. CIOf Timings for Write Operations................................ 45 Flash Erase and Program Operations .................................... 46 Figure 18. Program Operation Timings.......................................... Figure 19. Accelerated Program Timing Diagram.......................... Figure 20. Chip/Sector Erase Operation Timings .......................... Figure 21. Back-to-back Read/Write Cycle Timings ...................... Figure 22. Data# Polling Timings (During Embedded Algorithms). Figure 23. Toggle Bit Timings (During Embedded Algorithms)...... Figure 24. DQ2 vs. DQ6................................................................. 47 47 48 49 49 50 50 Hardware Data Protection ...................................................... 24 Low VCC Write Inhibit .............................................................. 24 Write Pulse “Glitch” Protection ............................................... 24 Logical Inhibit .......................................................................... 24 Power-Up Write Inhibit ............................................................ 24 Common Flash Memory Interface (CFI) . . . . . . . 24 Command Definitions . . . . . . . . . . . . . . . . . . . . . 27 Reading Array Data ................................................................ 27 Reset Command ..................................................................... 27 Autoselect Command Sequence ............................................ 27 Enter SecSi Sector/Exit SecSi Sector Command Sequence .. 28 Byte/Word Program Command Sequence ............................. 28 Unlock Bypass Command Sequence ..................................... 28 Figure 3. Program Operation .......................................................... 29 Temporary Sector/Sector Block Unprotect ............................. 51 Figure 25. Temporary Sector/Sector Block Unprotect Timing Diagram.............................................................................. 51 Figure 26. Sector/Sector Block Protect and Unprotect Timing Diagram.............................................................................. 52 Alternate CE#f Controlled Erase and Program Operations .... 53 Figure 27. Flash Alternate CE#f Controlled Write (Erase/Program) Operation Timings.......................................................................... 54 SRAM Read Cycle .................................................................. 55 Figure 28. SRAM Read Cycle—Address Controlled...................... 55 Figure 29. SRAM Read Cycle ........................................................ 56 Chip Erase Command Sequence ........................................... 29 Sector Erase Command Sequence ........................................ 29 Erase Suspend/Erase Resume Commands ........................... 30 Figure 4. Erase Operation............................................................... 30 Table 15. Autoselect Device IDs (Word Mode) ...............................31 Table 17. Autoselect Device IDs (Byte Mode) ................................32 SRAM Write Cycle .................................................................. 57 Figure 30. SRAM Write Cycle—WE# Control ................................ 57 Figure 31. SRAM Write Cycle—CE1#s Control ............................. 58 Figure 32. SRAM Write Cycle—UB#s and LB#s Control............... 59 Write Operation Status . . . . . . . . . . . . . . . . . . . . 33 DQ7: Data# Polling ................................................................. 33 Figure 5. Data# Polling Algorithm ................................................... 33 DQ6: Toggle Bit I .................................................................... 34 May 19, 2003 Flash Latchup Characteristics. . . . . . . . . . . . . . . Package Pin Capacitance . . . . . . . . . . . . . . . . . . Flash Data Retention . . . . . . . . . . . . . . . . . . . . . . SRAM Data Retention . . . . . . . . . . . . . . . . . . . . . . 60 60 60 61 Am42DL32x4G 3 PRELIMINARY Figure 33. CE1#s Controlled Data Retention Mode........................ 61 Figure 34. CE2s Controlled Data Retention Mode.......................... 61 FLB073—73-Ball Fine-Pitch Grid Array 8 x 11.6 mm ............. 62 Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 63 Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 62 4 Am42DL32x4G May 19, 2003 PRELIMINARY PRODUCT SELECTOR GUIDE Part Number Standard Voltage Speed Range: VCC = Options 2.7–3.3 V Max Access Time (ns) CE# Access (ns) OE# Access (ns) Flash Memory 71 70 70 30 70 70 70 30 85 85 85 40 71 55 55 25 Am42DL32x4G SRAM 70 70 70 35 85 85 85 35 MCP BLOCK DIAGRAM VCCf A20 to A0 A20 to A0 A–1 WP#/ACC RESET# CE#f CIOf VSS RY/BY# 32 M Bit Flash Memory DQ15/A-1 to DQ0 DQ15/A-1 to DQ0 VCCs/VCCQ VSS/VSSQ A0 toto A0 A17 A19 LB#s UB#s WE# OE# CE1#s CE2s 4 M Bit Static RAM DQ15/A-1 to DQ0 May 19, 2003 Am42DL32x4G 5 PRELIMINARY FLASH MEMORY BLOCK DIAGRAM OE# CIOf VCC VSS Y-Decoder A20–A0 Upper Bank Address Upper Bank Latches and Control Logic RY/BY# A20–A0 RESET# WE# CE# CIOf WP#/ACC DQ15–DQ0 A20–A0 STATE CONTROL & COMMAND REGISTER X-Decoder Status DQ15–DQ0 Control DQ15–DQ0 X-Decoder Lower Bank A20–A0 Lower Bank Address OE# 6 Am42DL32x4G Latches and Control Logic Y-Decoder CIOf DQ15–DQ0 A20–A0 May 19, 2003 PRELIMINARY CONNECTION DIAGRAM 73-Ball FBGA Top View A1 NC A10 NC Flash only B1 NC B5 NC B6 NC B10 NC SRAM only C1 NC C3 A7 C4 D4 UB# C5 D5 E5 RY/BY# C6 D6 E6 A20 C7 A8 C8 A11 Shared LB# WP#/ACC WE# D2 A3 D3 A6 D7 A19 D8 A12 D9 A15 RESET# CE2s E2 A2 E3 A5 E4 A18 E7 A9 E8 A13 E9 NC F1 NC F2 A1 F3 A4 F4 A17 F7 A10 F8 A14 F9 NC F10 NC G1 NC G2 A0 G3 VSS G4 DQ1 G7 DQ6 G8 NC G9 A16 G10 NC H2 CE#f H3 OE# H4 DQ9 H5 DQ3 H6 DQ4 H7 J7 DQ12 H8 J8 DQ7 H9 J9 VSS DQ13 DQ15/A-1 CIOf J2 CE1#s J3 DQ0 J4 DQ10 J5 VCCf J6 VCCs K3 DQ8 K4 DQ2 K5 DQ11 K6 NC K7 DQ5 K8 DQ14 L1 NC L5 NC L6 NC L10 NC M1 NC M10 NC Special Handling Instructions for FBGA Package Special handling is required for Flash Memory products in FBGA packages. Flash memory devices in FBGA packages may be damaged if exposed to ultrasonic cleaning methods. The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time. May 19, 2003 Am42DL32x4G 7 PRELIMINARY PIN DESCRIPTION A17–A0 = 18 Address Inputs (Common) A-1, A20–A18 = 4 Address Inputs (Flash) DQ15–DQ0 CE#f CE#s OE# WE# RY/BY# UB#s LB#s CIOf = 16 Data Inputs/Outputs (Common) = Chip Enable (Flash) = Chip Enable (SRAM) = Output Enable (Common) = Write Enable (Common) = Ready/Busy Output = Upper Byte Control (SRAM) = Lower Byte Control (SRAM) = I/O Configuration (Flash) CIOf = VIH = Word mode (x16), CIOf = VIL = Byte mode (x8) = Hardware Reset Pin, Active Low = Hardware Write Protect/ Acceleration Pin (Flash) = Flash 3.0 volt-only single power supply (see Product Selector Guide for speed options and voltage supply tolerances) = SRAM Power Supply = Device Ground (Common) = Pin Not Connected Internally LOGIC SYMBOL 18 A17–A0 A-1, A20–A18 CE#f CE1#s CE2s OE# WE# WP#/ACC RESET# UB#s LB#s CIOf RY/BY# DQ15–DQ0 16 or 8 RESET# WP#/ACC VCCf VCCs VSS NC 8 Am42DL32x4G May 19, 2003 PRELIMINARY ORDERING INFORMATION The order number (Valid Combination) is formed by the following: Am42DL32x 4 G T 70 I T TAPE AND REEL T = 7 inches TEMPERATURE RANGE I = Industrial (–40°C to +85°C) SPEED OPTION See Product Selector Guide and Valid Combinations BOOT CODE SECTOR ARCHITECTURE T = Top sector B = Bottom sector PROCESS TECHNOLOGY G= 0.17 µm SRAM DEVICE DENSITY 4 = 4 Mbits AMD DEVICE NUMBER/DESCRIPTION Am42DL32x4G Stacked Multi-Chip Package (MCP) Flash Memory and SRAM Am29DL32xG 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory and 4 Mbit (256 K x 16-Bit) Static RAM Valid Combinations Order Number Am42DL3224GT71I Am42DL3224GB71I Am42DL3234GT71I Am42DL3234GB71I Am42DL3244GT71I Am42DL3244GB71I Am42DL3224GT70I Am42DL3224GB70I Am42DL3224GT85I Am42DL3224GB85I Am42DL3234GT70I Am42DL3234GB70I Am42DL3234GT85I Am42DL3234GB85I Am42DL3244GT70I Am42DL3244GB70I Am42DL3244GT85I Am42DL3244GB85I T Package Marking M42000005W M42000005X M42000005Y M42000005Z M420000060 M420000061 M420000022 M420000023 M420000024 M420000025 M420000026 M420000027 M420000028 M420000029 M42000002A M42000002B M42000002C M42000002D Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations May 19, 2003 Am42DL32x4G 9 PRELIMINARY DEVICE BUS OPERATIONS This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The command register itself does not occupy any addressable memory locat ion. The reg ister is a lat ch used t o store th e commands, along with the address and data information needed to execute the command. The contents of the register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. Tables 1 through 2 list the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in further detail. 10 Am42DL32x4G May 19, 2003 PRELIMINARY Table 1. Operation (Notes 1, 2) Read from Flash CE#f L Device Bus Operations—Flash Word Mode, CIOf = VIH Addr. AIN AIN X X X X SADD, A6 = L, A1 = H, A0 = L SADD, A6 = H, A1 = H, A0 = L X LB#s UB#s RESET# X X H WP#/ACC (Note 4) L/H DQ7– DQ0 DOUT DIN High-Z DQ15– DQ8 DOUT DIN High-Z CE1#s CE2s OE# WE# H X H X H X L H X H X L X L X L H X L X L X L X L H L H L L H Write to Flash L VCC ± 0.3 V L H L X X H VCC ± 0.3 V H (Note 4) Standby X H H X X H H X X L X X X X L X H Output Disable Flash Hardware Reset Sector Protect (Note 5) L/H High-Z High-Z X L L/H High-Z High-Z L X H X X VID L/H DIN X Sector Unprotect (Note 5) Temporary Sector Unprotect L X H X X X VID (Note 6) DIN X X X X X L X L L H L L H VID (Note 6) DIN DOUT High-Z DOUT DOUT High-Z DIN DIN High-Z Read from SRAM H L H L H AIN H L L H X High-Z DOUT DIN Write to SRAM H L H X L AIN H L H X High-Z DIN Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 9.0 ± 0.5 V, X = Don’t Care, SADD = Flash Sector Address, AIN = Address In, DIN = Data In, DOUT = Data Out Notes: 1. Other operations except for those indicated in this column are inhibited. 2. Do not apply CE#f = VIL, CE1#s = VIL and CE2s = VIH at the same time. 3. Don’t care or open LB#s or UB#s. 4. If WP#/ACC = VIL , the boot sectors will be protected. If WP#/ACC = VIH the boot sectors protection will be removed. If WP#/ACC = VACC (9V), the program time will be reduced by 40%. 5. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector/Sector Block Protection and Unprotection” section. 6. If WP#/ACC = VIL, the two outermost boot sectors remain protected. If WP#/ACC = VIH, the two outermost boot sector protection depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection”. If WP#/ACC = VHH, all sectors will be unprotected. May 19, 2003 Am42DL32x4G 11 PRELIMINARY Table 2. Operation (Notes 1, 2) Read from Flash CE#f L Device Bus Operations—Flash Byte Mode, CIOf = VSS Addr. AIN AIN X LB#s UB#s WP#/ACC RESET# (Note 3) (Note 3) (Note 4) X X H L/H DQ7– DQ0 DOUT DIN High-Z DQ15– DQ8 High-Z CE1#s CE2s OE# WE# H X H X H X L H X H X L X L X L H X L X L X L x L H L H L L H Write to Flash L VCC ± 0.3 V L H L X X H VCC ± 0.3 V H (Note 3) High-Z Standby X X X L X X X X L X H High-Z Output Disable Flash Hardware Reset Sector Protect (Note 5) H H X L/H High-Z High-Z X X X X SADD, A6 = L, A1 = H, A0 = L SADD, A6 = L, A1 = H, A0 = L AIN L L/H High-Z High-Z L X H X X VID L/H DIN X Sector Unprotect (Note 5) Temporary Sector Unprotect L X H X X X VID (Note 6) DIN X X X X X L X L L H L L H VID (Note 6) DIN DOUT High-Z DOUT DOUT High-Z DIN DIN High-Z Read from SRAM H L H L H AIN H L L H X High-Z DOUT DIN Write to SRAM H L H X L AIN H L H X High-Z DIN Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 9.0 ± 0.5 V, X = Don’t Care, SADD = Flash Sector Address, AIN = Address In (for Flash Byte Mode, DQ15 = A-1), DIN = Data In, DOUT = Data Out Notes: 1. Other operations except for those indicated in this column are inhibited. 2. Do not apply CE#f = VIL, CE1#s = VIL and CE2s = VIH at the same time. 3. Don’t care or open LB#s or UB#s. 4. If WP#/ACC = VIL , the boot sectors will be protected. If WP#/ACC = VIH the boot sectors protection will be removed. If WP#/ACC = VACC (9V), the program time will be reduced by 40%. 5. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector/Sector Block Protection and Unprotection” section. 6. If WP#/ACC = VIL, the two outermost boot sectors remain protected. If WP#/ACC = VIH, the two outermost boot sector protection depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection”. If WP#/ACC = VHH, all sectors will be unprotected. 12 Am42DL32x4G May 19, 2003 PRELIMINARY Word/Byte Configuration The CIOf pin controls whether the device data I/O pins operate in the byte or word configuration. If the CIOf pin is set at logic ‘1’, the device is in word configuration, DQ15–DQ0 are active and controlled by CE# and OE#. If the CIOf pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ7–DQ0 are active and controlled by CE# and OE#. The data I/O pins DQ14–DQ8 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function. An erase operation can erase one sector, multiple sectors, or the entire device. Tables 4–7 indicate the address space that each sector occupies. The device address space is divided into two banks: Bank 1 contains the boot/parameter sectors, and Bank 2 contains the larger, code sectors of uniform size. A “bank address” is the address bits required to uniquely select a bank. Similarly, a “sector address” is the address bits required to uniquely select a sector. ICC2 in the DC Characteristics table represents the active current specification for the write mode. The AC Characteristics section contains timing specification tables and timing diagrams for write operations. Accelerated Program Operation The device offers accelerated program operations through the ACC function. This is one of two functions provided by the WP#/ACC pin. This function is primarily intended to allow faster manufacturing throughput at the factory. If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. The system would use a two-cycle program command sequence as required by the Unlock Bypass mode. Removing VHH from the WP#/ACC pin returns the device to normal operation. Note that the WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Autoselect Functions If the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ7–DQ0. Standard read cycle timings apply in this mode. Refer to the Autoselect Mode and Autoselect Command Sequence sections for more information. Requirements for Reading Array Data To read array data from the outputs, the system must drive the CE#f and OE# pins to VIL. CE#f is the power control and selects the device. OE# is the output control and gates array data to the output pins. WE# should remain at V I H . The CIOf pin determines whether the device outputs array data in words or bytes. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. Each bank remains enabled for read access until the command register contents are altered. See “Requirements for Reading Array Data” for more information. Refer to the AC Flash Read-Only Operations table for timing specifications and to Figure 14 for the timing diagram. I CC1 i n the DC Characteristics table represents the active current specification for reading array data. Writing Commands/Command Sequences To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE# and CE#f to VIL, and OE# to VIH. For program operations, the CIOf pin determines whether the device accepts program data in bytes or words. Refer to “Word/Byte Configuration” for more information. The device features an Unlock Bypass mode to facilitate faster programming. Once a bank enters the Unlock Bypass mode, only two write cycles are required to program a word or byte, instead of four. The “Word/Byte Configuration” section has details on programming data to the device using both standard and Unlock Bypass command sequences. Simultaneous Read/Write Operations with Zero Latency This device is capable of reading data from one bank of memory while programming or erasing in the other bank of memory. An erase operation may also be suspended to read from or program to another location within the same bank (except the sector being erased). Figure 21 shows how read and write cycles may be initiated for simultaneous operation with zero latency. ICC6 and ICC7 in the DC Characteristics table represent the current specifications for read-while-program and read-while-erase, respectively. May 19, 2003 Am42DL32x4G 13 PRELIMINARY Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE#f and RESET# pins are both held at VCC ± 0.3 V. (Note that this is a more restricted voltage range than V IH .) If CE#f and RESET# are held at V IH , but not within VCC ± 0.3 V, the device will be in the standby mode, but the standby current will be greater. The device requires standard access time (t CE ) for read access when the device is in either of these standby modes, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. ICC3 i n the DC Characteristics table represents the standby current specification. RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS ± 0.3 V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL but not within VSS ± 0.3 V, the standby current will be greater. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a “0” (busy) until the internal reset operation is complete, which requires a time of t READY ( during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is “1”), the reset operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data t RH after the RESET# pin returns to VIH. Refer to the AC Characteristics tables for RESET# parameters and to Figure 15 for the timing diagram. Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#f, WE#, and OE# control signals. Standard add r e ss a cce ss t im in g s pro vi de n ew d at a wh e n addresses are changed. While in sleep mode, output data is latched and always available to the system. ICC4 i n the DC Characteristics table represents the automatic sleep mode current specification. Output Disable Mode When the OE# input is at VIH, output from the device is disabled. The output pins are placed in the high impedance state. RESET#: Hardware Reset Pin The RESET# pin provides a hardware method of resetting the device to reading array data. When the Table 3. Device Part Number Am29DL322G Am29DL323G Am29DL324G Bank 1 Megabits 4 Mbit 8 Mbit 16 Mbit Sector Sizes Device Bank Division Bank 2 Megabits 28 Mbit 24 Mbit 16 Mbit Sector Sizes Fifty-six 64 Kbyte/32 Kword Forty-eight 64 Kbyte/32 Kword Thirty-two 64 Kbyte/32 Kword Eight 8 Kbyte/4 Kword, seven 64 Kbyte/32 Kword Eight 8 Kbyte/4 Kword, fifteen 64 Kbyte/32 Kword Eight 8 Kbyte/4 Kword, thirty-one 64 Kbyte/32 Kword 14 Am42DL32x4G May 19, 2003 PRELIMINARY Table 4. Am29DL324GT Am29DL323GT Am29DL322GT Top Boot Sector Addresses Sector Sector Address A20–A12 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 Bank 2 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 Bank 2 Bank 2 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 SA35 SA36 SA37 SA38 Bank 1 000000xxx 000001xxx 000010xxx 000011xxx 000100xxx 000101xxx 000110xxx 000111xxx 001000xxx 001001xxx 001010xxx 001011xxx 001100xxx 001101xxx 001110xxx 001111xxx 010000xxx 010001xxx 010010xxx 010011xxx 010100xxx 010101xxx 010110xxx 010111xxx 011000xxx 011001xxx 011010xxx 011011xxx 011100xxx 011101xxx 011110xxx 011111xxx 100000xxx 100001xxx 100010xxx 100011xxx 100100xxx 100101xxx 100110xxx 100111xxx 101000xxx 101001xxx 101010xxx 101011xxx 101100xxx 101101xxx 101110xxx 101111xxx 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 000000h–00FFFFh 010000h–01FFFFh 020000h–02FFFFh 030000h–03FFFFh 040000h–04FFFFh 050000h–05FFFFh 060000h–06FFFFh 070000h–07FFFFh 080000h–08FFFFh 090000h–09FFFFh 0A0000h–0AFFFFh 0B0000h–0BFFFFh 0C0000h–0CFFFFh 0D0000h–0DFFFFh 0E0000h–0EFFFFh 0F0000h–0FFFFFh 100000h–10FFFFh 110000h–11FFFFh 120000h–12FFFFh 130000h–13FFFFh 140000h–14FFFFh 150000h–15FFFFh 160000h–16FFFFh 170000h–17FFFFh 180000h–18FFFFh 190000h–19FFFFh 1A0000h–1AFFFFh 1B0000h–1BFFFFh 1C0000h–1CFFFFh 1D0000h–1DFFFFh 1E0000h–1EFFFFh 1F0000h–1FFFFFh 200000h–20FFFFh 210000h–21FFFFh 220000h–22FFFFh 230000h–23FFFFh 240000h–24FFFFh 250000h–25FFFFh 260000h–26FFFFh 270000h–27FFFFh 280000h–28FFFFh 290000h–29FFFFh 2A0000h–2AFFFFh 2B0000h–2BFFFFh 2C0000h–2CFFFFh 2D0000h–2DFFFFh 2E0000h–2EFFFFh 2F0000h–2FFFFFh 000000h–07FFFh 008000h–0FFFFh 010000h–17FFFh 018000h–01FFFFh 020000h–027FFFh 028000h–02FFFFh 030000h–037FFFh 038000h–03FFFFh 040000h–047FFFh 048000h–04FFFFh 050000h–057FFFh 058000h–05FFFFh 060000h–067FFFh 068000h–06FFFFh 070000h–077FFFh 078000h–07FFFFh 080000h–087FFFh 088000h–08FFFFh 090000h–097FFFh 098000h–09FFFFh 0A0000h–0A7FFFh 0A8000h–0AFFFFh 0B0000h–0B7FFFh 0B8000h–0BFFFFh 0C0000h–0C7FFFh 0C8000h–0CFFFFh 0D0000h–0D7FFFh 0D8000h–0DFFFFh 0E0000h–0E7FFFh 0E8000h–0EFFFFh 0F0000h–0F7FFFh 0F8000h–0FFFFFh 100000h–107FFFh 108000h–10FFFFh 110000h–117FFFh 118000h–11FFFFh 120000h–127FFFh 128000h–12FFFFh 130000h–137FFFh 138000h–13FFFFh 140000h–147FFFh 148000h–14FFFFh 150000h–157FFFh 158000h–15FFFFh 160000h–167FFFh 168000h–16FFFFh 170000h–177FFFh 178000h–17FFFFh SA39 SA40 SA41 SA42 SA43 SA44 SA45 SA46 SA47 May 19, 2003 Am42DL32x4G 15 PRELIMINARY Table 4. Am29DL324GT Am29DL323GT Am29DL322GT Top Boot Sector Addresses (Continued) Sector Sector Address A20–A12 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range SA48 SA49 SA50 Bank 2 SA51 SA52 SA53 SA54 SA55 SA56 SA57 Bank 1 Bank 1 SA58 SA59 SA60 SA61 Bank 1 SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 110000xxx 110001xxx 110010xxx 110011xxx 110100xxx 110101xxx 110110xxx 110111xxx 111000xxx 111001xxx 111010xxx 111011xxx 111100xxx 111101xxx 111110xxx 111111000 111111001 111111010 111111011 111111100 111111101 111111110 111111111 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4 300000h–30FFFFh 310000h–31FFFFh 320000h–32FFFFh 330000h–33FFFFh 340000h–34FFFFh 350000h–35FFFFh 360000h–36FFFFh 370000h–37FFFFh 380000h–38FFFFh 390000h–39FFFFh 3A0000h–3AFFFFh 3B0000h–3BFFFFh 3C0000h–3CFFFFh 3D0000h–3DFFFFh 3E0000h–3EFFFFh 3F0000h–3F1FFFh 3F2000h–3F3FFFh 3F4000h–3F5FFFh 3F6000h–3F7FFFh 3F8000h–3F9FFFh 3FA000h–3FBFFFh 3FC000h–3FDFFFh 3FE000h–3FFFFFh 180000h–187FFFh 188000h–18FFFFh 190000h–197FFFh 198000h–19FFFFh 1A0000h–1A7FFFh 1A8000h–1AFFFFh 1B0000h–1B7FFFh 1B8000h–1BFFFFh 1C0000h–1C7FFFh 1C8000h–1CFFFFh 1D0000h–1D7FFFh 1D8000h–1DFFFFh 1E0000h–1E7FFFh 1E8000h–1EFFFFh 1F0000h–1F7FFFh 1F8000h–1F8FFFh 1F9000h–1F9FFFh 1FA000h–1FAFFFh 1FB000h–1FBFFFh 1FC000h–1FCFFFh 1FD000h–1FDFFFh 1FE000h–1FEFFFh 1FF000h–1FFFFFh Note: The address range is A20:A-1 in byte mode (BYTE#=VIL) or A20:A0 in word mode (BYTE#=VIH). The bank address bits are A20–A18 for Am29DL322GT, A20 and A19 for Am29DL323GT, and A20 for Am29DL324GT. Table 5. Device Am29DL322GT, Am29DL323GT, Am29DL324GT Top Boot SecSi Sector Addresses Sector Address A20–A12 111111xxx Sector Size (bytes/words) 256/128 (x8) Address Range 3FE000h–3FE0FFh (x16) Address Range 1FF000h–1FF07Fh 16 Am42DL32x4G May 19, 2003 PRELIMINARY Table 6. Am29DL324GB Am29DL323GB Am29DL322GB Bottom Boot Sector Addresses Sector Sector Address A20–A12 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range SA0 SA1 SA2 SA3 SA4 SA5 Bank 1 SA6 SA7 SA8 SA9 Bank 1 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 Bank 1 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 Bank 2 SA26 SA27 SA28 SA29 Bank 2 SA30 SA31 SA32 SA33 SA34 SA35 SA36 SA37 SA38 000000000 000000001 000000010 000000011 000000100 000000101 000000110 000000111 000001xxx 000010xxx 000011xxx 000100xxx 000101xxx 000110xxx 000111xxx 001000xxx 001001xxx 001010xxx 001011xxx 001100xxx 001101xxx 001110xxx 001111xxx 010000xxx 010001xxx 010010xxx 010011xxx 010100xxx 010101xxx 010110xxx 010111xxx 011000xxx 011001xxx 011010xxx 011011xxx 011100xxx 011101xxx 011110xxx 011111xxx 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 000000h-001FFFh 002000h-003FFFh 004000h-005FFFh 006000h-007FFFh 008000h-009FFFh 00A000h-00BFFFh 00C000h-00DFFFh 00E000h-00FFFFh 010000h-01FFFFh 020000h-02FFFFh 030000h-03FFFFh 040000h-04FFFFh 050000h-05FFFFh 060000h-06FFFFh 070000h-07FFFFh 080000h-08FFFFh 090000h-09FFFFh 0A0000h-0AFFFFh 0B0000h-0BFFFFh 0C0000h-0CFFFFh 0D0000h-0DFFFFh 0E0000h-0EFFFFh 0F0000h-0FFFFFh 100000h-10FFFFh 110000h-11FFFFh 120000h-12FFFFh 130000h-13FFFFh 140000h-14FFFFh 150000h-15FFFFh 160000h-16FFFFh 170000h-17FFFFh 180000h-18FFFFh 190000h-19FFFFh 1A0000h-1AFFFFh 1B0000h-1BFFFFh 1C0000h-1CFFFFh 1D0000h-1DFFFFh 1E0000h-1EFFFFh 1F0000h-1FFFFFh 000000h–000FFFh 001000h–001FFFh 002000h–002FFFh 003000h–003FFFh 004000h–004FFFh 005000h–005FFFh 006000h–006FFFh 007000h–007FFFh 008000h–00FFFFh 010000h–017FFFh 018000h–01FFFFh 020000h–027FFFh 028000h–02FFFFh 030000h–037FFFh 038000h–03FFFFh 040000h–047FFFh 048000h–04FFFFh 050000h–057FFFh 058000h–05FFFFh 060000h–067FFFh 068000h–06FFFFh 070000h–077FFFh 078000h–07FFFFh 080000h–087FFFh 088000h–08FFFFh 090000h–097FFFh 098000h–09FFFFh 0A0000h–0A7FFFh 0A8000h–0AFFFFh 0B0000h–0B7FFFh 0B8000h–0BFFFFh 0C0000h–0C7FFFh 0C8000h–0CFFFFh 0D0000h–0D7FFFh 0D8000h–0DFFFFh 0E0000h–0E7FFFh 0E8000h–0EFFFFh 0F0000h–0F7FFFh 0F8000h–0FFFFFh May 19, 2003 Am42DL32x4G 17 PRELIMINARY Table 6. Am29DL324GB Am29DL323GB Am29DL322GB Bottom Boot Sector Addresses (Continued) Sector Sector Address A20–A12 Sector Size (Kbytes/Kwords) (x8) Address Range (x16) Address Range SA39 SA40 SA41 SA42 SA43 SA44 SA45 SA46 SA47 SA48 SA49 SA50 SA51 SA52 SA53 Bank 2 Bank 2 Bank 2 SA54 SA55 SA56 SA57 SA58 SA59 SA60 SA61 SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 100000xxx 100001xxx 100010xxx 100011xxx 100100xxx 100101xxx 100110xxx 100111xxx 101000xxx 101001xxx 101010xxx 101011xxx 101100xxx 101101xxx 101110xxx 101111xxx 111000xxx 110001xxx 110010xxx 110011xxx 110100xxx 110101xxx 110110xxx 110111xxx 111000xxx 111001xxx 111010xxx 111011xxx 111100xxx 111101xxx 111110xxx 111111xxx 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 200000h-20FFFFh 210000h-21FFFFh 220000h-22FFFFh 230000h-23FFFFh 240000h-24FFFFh 250000h-25FFFFh 260000h-26FFFFh 270000h-27FFFFh 280000h-28FFFFh 290000h-29FFFFh 2A0000h-2AFFFFh 2B0000h-2BFFFFh 2C0000h-2CFFFFh 2D0000h-2DFFFFh 2E0000h-2EFFFFh 2F0000h-2FFFFFh 300000h-30FFFFh 310000h-31FFFFh 320000h-32FFFFh 330000h-33FFFFh 340000h-34FFFFh 350000h-35FFFFh 360000h-36FFFFh 370000h-37FFFFh 380000h-38FFFFh 390000h-39FFFFh 3A0000h-3AFFFFh 3B0000h-3BFFFFh 3C0000h-3CFFFFh 3D0000h-3DFFFFh 3E0000h-3EFFFFh 3F0000h-3FFFFFh 100000h–107FFFh 108000h–10FFFFh 110000h–117FFFh 118000h–11FFFFh 120000h–127FFFh 128000h–12FFFFh 130000h–137FFFh 138000h–13FFFFh 140000h–147FFFh 148000h–14FFFFh 150000h–157FFFh 158000h–15FFFFh 160000h–167FFFh 168000h–16FFFFh 170000h–177FFFh 178000h–17FFFFh 180000h–187FFFh 188000h–18FFFFh 190000h–197FFFh 198000h–19FFFFh 1A0000h–1A7FFFh 1A8000h–1AFFFFh 1B0000h–1B7FFFh 1B8000h–1BFFFFh 1C0000h–1C7FFFh 1C8000h–1CFFFFh 1D0000h–1D7FFFh 1D8000h–1DFFFFh 1E0000h–1E7FFFh 1E8000h–1EFFFFh 1F0000h–1F7FFFh 1F8000h–1FFFFFh Note: The address range is A20:A-1 in byte mode (BYTE#=VIL) or A20:A0 in word mode (BYTE#=VIH). The bank address bits are A20–A18 for Am29DL322GB, A20 and A19 for Am29DL323GB, and A20 for Am29DL324GB. Table 7. Device Am29DL322GB, Am29DL323GB, Am29DL324GB Bottom Boot SecSi Sector Addresses Sector Address A20–A12 000000xxx Sector Size (bytes/words) 256/128 (x8) Address Range 000000h-0000FFh (x16) Address Range 00000h-0007Fh 18 Am42DL32x4G May 19, 2003 PRELIMINARY Autoselect Mode The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. The autoselect codes can also be accessed in-system through the command register. The host system can issue the autoselect command via the command register, as shown in Tables 14 and 16. This method does not require VID. Refer to the Autoselect Command Sequence section for more information. Table 8. Top Boot Sector/Sector Block Addresses for Protection/Unprotection A20–A12 000000XXX 000001XXX, 000010XXX 000011XXX 0001XXXXX 0010XXXXX 0011XXXXX 0100XXXXX 0101XXXXX 0110XXXXX 0111XXXXX 1000XXXXX 1001XXXXX 1010XXXXX 1011XXXXX 1100XXXXX 1101XXXXX 1110XXXXX 111100XXX, 111101XXX, 111110XXX 111111000 111111001 111111010 111111011 111111100 111111101 111111110 111111111 Sector/ Sector Block Size 64 Kbytes 192 (3x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 192 (4x64) Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes Sector SA0 SA1-SA3 SA4-SA7 SA8-SA11 SA12-SA15 SA16-SA19 SA20-SA23 SA24-SA27 SA28-SA31 SA32-SA35 SA36-SA39 SA40-SA43 SA44-SA47 SA48-SA51 SA52-SA55 SA56-SA59 SA60-SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 Sector/Sector Block Protection and Unprotection (Note: For the following discussion, the term “sector” applies to both sectors and sector blocks. A sector block consists of two or more adjacent sectors that are protected or unprotected at the same time (see Table 8). May 19, 2003 Am42DL32x4G 19 PRELIMINARY Table 9. Bottom Boot Sector/Sector Block Addresses for Protection/Unprotection Sector SA70 SA69-SA67 SA66-SA63 SA62-SA59 SA58-SA55 SA54-SA51 SA50-SA47 SA46-SA43 SA42-SA39 SA38-SA35 SA34-SA31 SA30-SA27 SA26-SA23 SA22–SA19 SA18-SA15 SA14-SA11 SA10-SA8 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 A20–A12 111111XXX 111110XXX, 111101XXX, 111100XXX 1110XXXXX 1101XXXXX 1100XXXXX 1011XXXXX 1010XXXXX 1001XXXXX 1000XXXXX 0111XXXXX 0110XXXXX 0101XXXXX 0100XXXXX 0011XXXXX 0010XXXXX 0001XXXXX 000011XXX, 000010XXX, 000001XXX 000000111 000000110 000000101 000000100 000000011 000000010 000000001 000000000 Sector/Sector Block Size 64 Kbytes 192 (3x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 256 (4x64) Kbytes 192 (3x64) Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes 8 Kbytes shows the algorithms and Figure 26 shows the timing diagram. This method uses standard microprocessor bus cycle timing. For sector unprotect, all unprotected sectors must first be protected prior to the first sector unprotect write cycle. The device is shipped with all sectors unprotected. It is possible to determine whether a sector is protected or unprotected. See the Autoselect Mode section for details. Write Protect (WP#) The Write Protect function provides a hardware method of protecting certain boot sectors without using VID. This function is one of two provided by the WP#/ACC pin. If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the two “outermost” 8 Kbyte boot sectors independently of whether those sectors were protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection”. The two outermost 8 Kbyte boot sectors are the two sectors containing the lowest addresses in a top-boot-configured device, or the two sectors containing the highest addresses in a top-boot-configured device. If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the two outermost 8 Kbyte boot sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these two sectors depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block Protection and Unprotection”. Note that the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Temporary Sector/Sector Block Unprotect The hardware sector protection feature disables both program and erase operations in any sector. The hardware sector unprotection feature re-enables both program and erase operations in previously protected sectors. Note that the sector unprotect algorithm unprotects all sectors in parallel. All previously protected sectors must be individually re-protected. To change data in protected sectors efficiently, the temporary sector un protect function is available. See “Temporary Sector/Sector Block Unprotect”. Sector protection and unprotection can be implemented as follows. Sector protection and unprotection requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 1 (Note: For the following discussion, the term “sector” applies to both sectors and sector blocks. A sector block consists of two or more adjacent sectors that are protected or unprotected at the same time (see Table 8). This feature allows temporary unprotection of previously protected sectors to change data in-system. The Sector Unprotect mode is activated by setting the RESET# pin to VID (11.5 V – 12.5 V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses. Once VID is removed from the RESET# pin, all the previously protected sectors are protected again. Figure 1 shows the algorithm, and Figure 25 shows the timing diagrams, for this feature. 20 Am42DL32x4G May 19, 2003 PRELIMINARY START RESET# = VID (Note 1) Perform Erase or Program Operations RESET# = VIH Temporary Sector Unprotect Completed (Note 2) Notes: 1. All protected sectors unprotected (If WP#/ACC = VIL, outermost boot sectors will remain protected). 2. All previously protected sectors are protected once again. Figure 1. Temporary Sector Unprotect Operation May 19, 2003 Am42DL32x4G 21 PRELIMINARY START PLSCNT = 1 RESET# = VID Wait 1 µs Protect all sectors: The indicated portion of the sector protect algorithm must be performed for all unprotected sectors prior to issuing the first sector unprotect address START PLSCNT = 1 RESET# = VID Wait 1 µs Temporary Sector Unprotect Mode No First Write Cycle = 60h? Yes Set up sector address Sector Protect: Write 60h to sector address with A6 = 0, A1 = 1, A0 = 0 Wait 150 µs Verify Sector Protect: Write 40h to sector address with A6 = 0, A1 = 1, A0 = 0 Read from sector address with A6 = 0, A1 = 1, A0 = 0 No No First Write Cycle = 60h? Yes All sectors protected? Yes Set up first sector address Sector Unprotect: Write 60h to sector address with A6 = 1, A1 = 1, A0 = 0 Temporary Sector Unprotect Mode Increment PLSCNT Reset PLSCNT = 1 Wait 15 ms Verify Sector Unprotect: Write 40h to sector address with A6 = 1, A1 = 1, A0 = 0 No No PLSCNT = 25? Yes Data = 01h? Increment PLSCNT Yes No Yes No Read from sector address with A6 = 1, A1 = 1, A0 = 0 Set up next sector address Device failed Protect another sector? No Remove VID from RESET# PLSCNT = 1000? Yes Data = 00h? Yes Device failed Write reset command Last sector verified? Yes No Sector Protect Algorithm Sector Protect complete Sector Unprotect Algorithm Remove VID from RESET# Write reset command Sector Unprotect complete Note: The term “sector” in the figure applies to both sectors and sector blocks. Figure 1. In-System Sector/Sector Block Protect and Unprotect Algorithms 22 Am42DL32x4G May 19, 2003 PRELIMINARY SecSi (Secured Silicon) Sector Flash Memory Region The SecSi (Secured Silicon) Sector feature provides a Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The SecSi Sector uses a SecSi Sector Indicator Bit to indicate whether or not the SecSi Sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevents cloning of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. AMD offers the device with the SecSi Sector either f actory locke d o r cu st omer lockable. Th e f actory-locked version is always protected when shipped from the factory, and has the SecSi Sector Indicator Bit permanently set to a “1.” The customer-lockable version is shipped with the unprotected, allowing customers to utilize the that sector in any manner they choose. The customer-lockable version has the SecSi Sector Indicator Bit permanently set to a “0.” Thus, the SecSi Sector Indicator Bit prevents customer-lockable devices from being used to replace devices that are factory locked. The system accesses the SecSi Sector through a command sequence (see “Enter SecSi Sector/Exit SecSi Sector Command Sequence”). After the system has written the Enter SecSi Sector command sequence, it may read the SecSi Sector by using the addresses normally occupied by the boot sectors. This mode of operation continues until the system issues the Exit SecSi Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending commands to the boot sectors. Factory Locked: SecSi Sector Programmed and Protected At the Factory In a factory locked device, the SecSi Sector is protected when the device is shipped from the factory. The SecSi Sector cannot be modified in any way. The device is available preprogrammed with a random, secure ESN only. In the Top Boot device the ESN is located at addresses 1FF000h–1FF007h in word mode (or addresses 3FE000h–3FE00Fh in byte mode). In the Bottom Boot device the ESN is located at addresses 00000h–00007Fh in word mode (or 000000h–0000FFh in byte mode). Customer Lockable: SecSi Sector NOT Programmed or Protected At the Factory If the security feature is not required, the SecSi Sector can be treated as an additional Flash memory space, expanding the size of the available Flash array. The SecSi Sector can be read any number of times, but can be programmed and locked only once, and cannot be erased. Note that the accelerated programming (ACC) and unlock bypass functions are not available when programming the SecSi Sector. The SecSi Sector area can be protected using one of the following procedures: ■ Write the three-cycle Enter SecSi Sector Region command sequence, and then follow the in-system sector protect algorithm as shown in Figure 1, except that RESET# may be at either VIH or VID. This allows in-system protection of the without raising any device pin to a high voltage. Note that this method is only applicable to the SecSi Sector. ■ To verify the protect/unprotect status of the SecSi Sector, follow the algorithm shown in Figure 2.. Once the SecSi Sector is locked and verified, the syste m mu st w ri te t he E xit Se cSi Se ct or Re gio n command sequence to return to reading and writing the remainder of the array. The SecSi Sector protection must be used with caution since, once protected, there is no procedure available for unprotecting the SecSi Sector area and none of the bits in the SecSi Sector memory space can be modified in any way. START RESET# = VIH or VID Wait 1 µs Write 60h to any address If data = 00h, SecSi Sector is unprotected. If data = 01h, SecSi Sector is protected. Remove VIH or VID from RESET# Write 40h to SecSi Sector address with A6 = 0, A1 = 1, A0 = 0 Read from SecSi Sector address with A6 = 0, A1 = 1, A0 = 0 Write reset command SecSi Sector Protect Verify complete Figure 2. SecSi Sector Protect Verify May 19, 2003 Am42DL32x4G 23 PRELIMINARY Hardware Data Protection The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes (refer to Tables 14 and 16 for command definitions). In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise. Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to reading array data. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when VCC is greater than VLKO. Write Pulse “Glitch” Protection Noise pulses of less than 5 ns (typical) on OE#, CE#f or WE# do not initiate a write cycle. Logical Inhibit Write cycles are inhibited by holding any one of OE# = VIL, CE#f = VIH or WE# = VIH. To initiate a write cycle, CE#f and WE# must be a logical zero while OE# is a logical one. Power-Up Write Inhibit If WE# = CE#f = VIL and OE# = VIH during power up, the device does not accept commands on the rising Table 10. Addresses (Word Mode) 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah Addresses (Byte Mode) 20h 22h 24h 26h 28h 2Ah 2Ch 2Eh 30h 32h 34h Data 0051h 0052h 0059h 0002h 0000h 0040h 0000h 0000h 0000h 0000h 0000h edge of WE#. The internal state machine is automatically reset to reading array data on power-up. COMMON FLASH MEMORY INTERFACE (CFI) The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h in word mode (or address AAh in byte mode), any time the device is ready to read array data. The system can read CFI information at the addresses given in Tables 10–13. To terminate reading CFI data, the system must write the reset command. The CFI Query mode is not accessible when the device is executing an Embedded Program or embedded erase algorithm. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Tables 10–13. The system must write the reset command to return the device to reading array data. For further information, please refer to the CFI Specification and CFI Publication 100, available via the World Wide Web at http://www.amd.com/flash/cfi. Alternatively, contact an AMD representative for copies of these documents. CFI Query Identification String Description Query Unique ASCII string “QRY” Primary OEM Command Set Address for Primary Extended Table Alternate OEM Command Set (00h = none exists) Address for Alternate OEM Extended Table (00h = none exists) 24 Am42DL32x4G May 19, 2003 PRELIMINARY Table 11. Addresses (Word Mode) 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h Addresses (Byte Mode) 36h 38h 3Ah 3Ch 3Eh 40h 42h 44h 46h 48h 4Ah 4Ch Data 0027h 0036h 0000h 0000h 0004h 0000h 000Ah 0000h 0005h 0000h 0004h 0000h System Interface String Description VCC Min. (write/erase) D7–D4: volt, D3–D0: 100 millivolt VCC Max. (write/erase) D7–D4: volt, D3–D0: 100 millivolt VPP Min. voltage (00h = no VPP pin present) VPP Max. voltage (00h = no VPP pin present) Typical timeout per single byte/word write 2N µs Typical timeout for Min. size buffer write 2N µs (00h = not supported) Typical timeout per individual block erase 2N ms Typical timeout for full chip erase 2N ms (00h = not supported) Max. timeout for byte/word write 2N times typical Max. timeout for buffer write 2N times typical Max. timeout per individual block erase 2N times typical Max. timeout for full chip erase 2N times typical (00h = not supported) Table 12. Addresses (Word Mode) 27h 28h 29h 2Ah 2Bh 2Ch 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch Addresses (Byte Mode) 4Eh 50h 52h 54h 56h 58h 5Ah 5Ch 5Eh 60h 62h 64h 66h 68h 6Ah 6Ch 6Eh 70h 72h 74h 76h 78h Data 0016h 0002h 0000h 0000h 0000h 0002h 0007h 0000h 0020h 0000h 003Eh 0000h 0000h 0001h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h Device Geometry Definition Description Device Size = 2N byte Flash Device Interface description (refer to CFI publication 100) Max. number of byte in multi-byte write = 2N (00h = not supported) Number of Erase Block Regions within device Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) Erase Block Region 2 Information Erase Block Region 3 Information Erase Block Region 4 Information May 19, 2003 Am42DL32x4G 25 PRELIMINARY Table 13. Addresses (Word Mode) 40h 41h 42h 43h 44h 45h Addresses (Byte Mode) 80h 82h 84h 86h 88h 8Ah Primary Vendor-Specific Extended Query Description Data 0050h 0052h 0049h 0031h 0033h 0004h Query-unique ASCII string “PRI” Major version number, ASCII Minor version number, ASCII Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Silicon Revision Number (Bits 7-2) 46h 47h 48h 49h 4Ah 4Bh 4Ch 4Dh 8Ch 8Eh 90h 92h 94h 96h 98h 9Ah 0002h 0001h 0001h 0004h 00XXh (See Note) 0000h 0000h 0085h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write Sector Protect 0 = Not Supported, X = Number of sectors in per group Sector Temporary Unprotect 00 = Not Supported, 01 = Supported Sector Protect/Unprotect scheme 04 = 29LV800 mode Simultaneous Operation 00 = Not Supported, X= Number of Sectors in Bank 2 (Uniform Bank) Burst Mode Type 00 = Not Supported, 01 = Supported Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV Top/Bottom Boot Sector Flag 02h = Bottom Boot Device, 03h = Top Boot Device 4Eh 9Ch 0095h 4Fh 9Eh 000Xh Note: The number of sectors in Bank 2 is device dependent. Am29DL322 = 38h, Am29DL323 = 30h, Am29DL324 = 20h. 26 Am42DL32x4G May 19, 2003 PRELIMINARY COMMAND DEFINITIONS Writing specific address and data commands or sequences into the command register initiates device operations. Tables 14 and 16 define the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence may place the device in an unknown state. A reset command is then required to return the device to reading array data. All addresses are latched on the falling edge of WE# or CE#f, whichever happens later. All data is latched on the rising edge of WE# or CE#f, whichever happens first. Refer to the AC Characteristics section for timing diagrams. before programming begins. This resets the bank to which the system was writing to reading array data. If the program command sequence is written to a bank that is in the Erase Suspend mode, writing the reset comm an d ret urns t hat ba nk to t he e rase -s uspe n d - r e a d m o d e . On c e p r o g r a mm i n g b e g in s , however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to reading array data. If a bank entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns that bank to the erase-suspend-read mode. If DQ5 goes high during a program or erase operation, writing the reset command returns the banks to reading array data (or erase-suspend-read mode if that bank was in Erase Suspend). Reading Array Data The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. Each bank is ready to read array data after completing an Embedded Program or Embedded Erase algorithm. After the device accepts an Erase Suspend command, the corresponding bank enters the erase-suspend-read mode, after which the system can read data from any non-erase-suspended sector within the same bank. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See the Erase Suspend/Erase Resume Commands section for more information. The system must issue the reset command to return a bank to the read (or erase-suspend-read) mode if DQ5 goes high during an active program or erase operation, or if the bank is in the autoselect mode. See the next section, Reset Command, for more information. See also Requirements for Reading Array Data in the “Device Bus Operations” section for more information. The Flash Read-Only Operations table provides the read parameters, and Figure 14 shows the timing diagram. Autoselect Command Sequence The autoselect command sequence allows the host system to access the manufacturer and device codes, and determine whether or not a sector is protected. Tables 14 and 16 show the address and data requirements. The autoselect command sequence may be written to an address within a bank that is either in the read or erase-suspend-read mode. The autoselect command may not be written while the device is actively programming or erasing in the other bank. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains the bank address and the auto se l ec t co mm a n d. T h e b an k th e n en t e r s t h e autoselect mode. The system may read at any address within the same bank any number of times without initiating another autoselect command sequence: ■ A read cycle at address (BA)XX00h (where BA is the bank address) returns the manufacturer code. ■ A read cycle at address (BA)XX01h in word mode (or (BA)XX02h in byte mode) returns the device code. ■ A read cycle to an address containing a sector address (SA) within the same bank, and the address 02h on A7–A0 in word mode (or the address 04h on A6–A-1 in byte mode) returns 01h if the sector is protected, or 00h if it is unprotected. (Refer to Tables 4–7 for valid sector addresses). The system must write the reset command to return to reading array data (or erase-suspend-read mode if the bank was previously in Erase Suspend). Reset Command Writing the reset command resets the banks to the read or erase-suspend-read mode. Address bits are don’t cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the bank to which the system was writing to reading array data. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence May 19, 2003 Am42DL32x4G 27 PRELIMINARY Enter SecSi Sector/Exit SecSi Sector Command Sequence The system can access the SecSi Sector region by issuing the three-cycle Enter SecSi Sector command sequence. The device continues to access the SecSi Sector region until the system issues the four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector command sequence returns the device to normal operation. Tables 14 and 16 show the address and data requirements for both command sequences. See also “SecSi (Secured Silicon) Sector Flash Memory Region” for further information. Note that a hardware reset (RESET#=VIL) will reset the device to reading array data. Note that the ACC function and unlock bypass modes are not available when the SecSi Sector is enabled. cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the data is still “0.” Only erase operations can convert a “0” to a “1.” Unlock Bypass Command Sequence The unlock bypass feature allows the system to program bytes or words to a bank faster than using the standard program command sequence. The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. That bank then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. Tables 14 and 16 show the requirements for the command sequence. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the bank address and the data 90h. The second cycle need only contain the data 00h. The bank then returns to the reading array data. The device offers accelerated program operations through the WP#/ACC pin. When the system asserts VHH on the WP#/ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass program command sequence. The device uses the higher voltage on the WP#/ACC pin to accelerate the operation. Note that the WP#/ACC pin must not be at VHH any operation other than accelerated programming, or device damage may result. In addition, the WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. Figure 3 illustrates the algorithm for the program operat io n . R e fe r t o t he F la sh Era se an d Pro g r am Operations table in the AC Characteristics section for parameters, and Figure 18 for timing diagrams. Byte/Word Program Command Sequence The system may program the device by word or byte, depending on the state of the CIOf pin. Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. Tables 14 and 16 show the address and data requirements for the byte program command sequence. When the Embedded Program algorithm is complete, that bank then returns to reading array data and addresses are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or RY/BY#. Refer to the Write Operation Status section for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once that bank has returned to reading array data, to ensure data integrity. N ote that the SecSi Sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Programming is allowed in any sequence and across sector boundaries. A b it cannot be programmed from “0” back to a “1.” A ttempting to do so may 28 Am42DL32x4G May 19, 2003 PRELIMINARY Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once that bank has returned to reading array data, to ensure data integrity. Figure 4 illustrates the algorithm for the erase operation. Refer to the Flash Erase and Program Operations tables in the AC Characteristics section for param et ers, and Figu re 20 sect ion fo r tim ing diagrams. START Write Program Command Sequence Embedded Program algorithm in progress Data Poll from System Sector Erase Command Sequence Verify Data? No Yes No Increment Address Last Address? Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and the sector erase command. Tables 14 and 16 show the address and data requirements for the sector erase command sequence. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of 50 µs occurs. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 µs, otherwise erasure may begin. Any sector erase address and command following the exceeded time-out may or may not be accepted. It is recommended that processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is written. Any command other than Se ctor E rase or E rase Suspend dur ing the time-out period resets that bank to reading array data. T he system must rewrite the command sequence and any additional addresses and commands. Note that the SecSi Sector, autoselect, and CFI functions are unavailable when an erase operation in is progress. The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section on DQ3: Sector Erase Timer.). The time-out begins from the rising edge of the final WE# pulse in the command sequence. When the Embedded Erase algorithm is complete, the bank returns to reading array data and addresses are Yes Programming Completed Note: See Tables 14 and 16 for program command sequence. Figure 3. Program Operation Chip Erase Command Sequence Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Tables 14 and 16 show the address and data requirements for the chip erase command sequence. When the Embedded Erase algorithm is complete, that bank returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/BY#. Refer to the Write Operation Status section for information on these status bits. Note that the SecSi Sector, autoselect, and CFI functions are unavailable when an erase operation in is progress. May 19, 2003 Am42DL32x4G 29 PRELIMINARY n o longer latched. Note that while the Embedded Erase operation is in progress, the system can read data from the non-erasing bank. The system can determine the status of the erase operation by reading DQ7, DQ6, DQ2, or RY/BY# in the erasing bank. Refer to the Write Operation Status section for information on these status bits. Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once that bank has returned to reading array data, to ensure data integrity. Figure 4 illustrates the algorithm for the erase operation. Refer to the Flash Erase and Program Operations tables in the AC Characteristics section for p ar am ete rs, a nd F igu re 2 0 sectio n fo r tim ing diagrams. After an erase-suspended program operation is complete, the bank returns to the erase-suspend-read mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard Byte Program operation. Refer to the Write Operation Status section for more information. In the erase-suspend-read mode, the system can also issue the autoselect command sequence. Refer to the Autoselect Mode and Autoselect Command Sequence sections for details. To resume the sector erase operation, the system must write the Erase Resume command. The bank address of the erase-suspended bank is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. Erase Suspend/Erase Resume Commands The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. The bank address is required when writing this command. This command is valid only during the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of 20 µs to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After the erase operation has been suspended, the bank enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to the Write Operation Status section for information on these status bits. START Write Erase Command Sequence (Notes 1, 2) Data Poll to Erasing Bank from System Embedded Erase algorithm in progress No Data = FFh? Yes Erasure Completed Notes: 1. See Tables 14 and 16 for erase command sequence. 2. See the section on DQ3 for information on the sector erase timer. Figure 4. Erase Operation 30 Am42DL32x4G May 19, 2003 PRELIMINARY Table 14. Command Sequence (Note 1) Read (Note 6) Reset (Note 7) Autoselect (Note 8) Manufacturer ID Device ID SecSi Sector Factory Protect (Note 9) Sector Protect Verify (Note 10) Cycles First Addr RA XXX 555 555 555 555 555 555 555 555 XXX BA 555 555 BA BA 55 Data RD F0 AA AA AA AA AA AA AA AA A0 90 AA AA B0 30 98 PD = Data to be programmed at location PA. Data latches on the rising edge of WE# or CE#f pulse, whichever happens first. SADD = Address of the sector to be verified (in autoselect mode) or erased. Address bits A20–A12 uniquely select any sector. BA = Address of the bank that is being switched to autoselect mode, is in bypass mode, or is being erased. Command Definitions (Flash Word Mode) Bus Cycles (Notes 2–5) Second Addr Data Third Addr Data Addr Fourth Data Fifth Addr Data Sixth Addr Data 1 1 4 4 4 4 3 4 4 3 2 2 6 6 1 1 1 2AA 2AA 2AA 2AA 2AA 2AA 2AA 2AA PA XXX 2AA 2AA 55 55 55 55 55 55 55 55 PD 00 55 55 (BA)555 (BA)555 (BA)555 (BA)555 555 555 555 555 90 90 90 90 88 90 A0 20 (BA)X00 0001 (BA)X01 see Table 15 (BA)X03 (SADD) X02 XXX PA 0082/0002 0000/0001 Enter SecSi Sector Region Exit SecSi Sector Region Program Unlock Bypass Unlock Bypass Program (Note 11) Unlock Bypass Reset (Note 12) Chip Erase Sector Erase Erase Suspend (Note 13) Erase Resume (Note 14) CFI Query (Note 15) 00 PD 555 555 80 80 555 555 AA AA 2AA 2AA 55 55 555 SADD 10 30 Legend: X = Don’t care RA = Address of the memory location to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE#f pulse, whichever happens later. Notes: 1. See Table 1 for description of bus operations. 2. 3. 4. 5. 6. 7. All values are in hexadecimal. Except for the read cycle and the fourth cycle of the autoselect command sequence, all bus cycles are write cycles. Data bits DQ15–DQ8 are don’t care in command sequences, except for RD and PD. Unless otherwise noted, address bits A20–A12 are don’t cares. No unlock or command cycles required when bank is in read mode. The Reset command is required to return to reading array data (or to the erase-suspend-read mode if previously in Erase Suspend) when a bank is in the autoselect mode, or if DQ5 goes high (while the bank is providing status information). The fourth cycle of the autoselect command sequence is a read cycle. The system must provide the bank address to obtain the manufacturer ID, device ID, or SecSi Sector factory protect information. See the Autoselect Command Sequence section for more information. The data is 80h for factory locked and 00h for not factory locked. 11. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 12. The Unlock Bypass Reset command is required to return to reading array data when the bank is in the unlock bypass mode. 13. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation, and requires the bank address. 14. The Erase Resume command is valid only during the Erase Suspend mode, and requires the bank address. 15. Command is valid when device is ready to read array data or when device is in autoselect mode. 8. Table 15. Device Autoselect Device IDs (Word Mode) Autoselect Device ID 2255h (T), 2256h (B) 2250h (T), 2253h (B) 225Ch (T), 225Fh (B) Am29DL322G Am29DL323G Am29DL324G 9. 10. The data is 00h for an unprotected sector/sector block and 01h for a protected sector/sector block. T = Top Boot Sector, B = Bottom Boot Sector May 19, 2003 Am42DL32x4G 31 PRELIMINARY Table 16. Command Sequence (Note 1) Read (Note 6) Reset (Note 7) Autoselect (Note 8) Manufacturer ID Device ID SecSi Sector Factory Protect (Note 9) Sector Protect Verify (Note 10) Command Definitions (Flash Byte Mode) Second Addr Data Bus Cycles (Notes 2–5) Third Fourth Addr Data Addr Data Fifth Sixth Addr Data Addr Data Cycles 1 1 4 6 4 4 3 4 4 3 2 2 6 6 1 1 1 First Addr Data RA XXX AAA AAA AAA AAA AAA AAA AAA AAA XXX XXX AAA AAA BA BA 55 RD F0 AA AA AA AA AA AA AA AA A0 90 AA AA B0 30 98 555 555 555 555 555 555 555 555 PA XXX 555 555 55 55 55 55 55 55 55 55 PD 00 55 55 (BA) AAA (BA) AAA (BA) AAA (BA) AAA AAA AAA AAA AAA 90 90 90 90 88 90 A0 20 (BA) 00 (BA) 02 (BA) X06 (SADD) X04 XXX PA 01 see Table 17 82/02 00 01 00 PD Enter SecSi Sector Region Exit SecSi Sector Region Program Unlock Bypass Unlock Bypass Program (Note 11) Unlock Bypass Reset (Note 12) Chip Erase Sector Erase Erase Suspend (Note 13) Erase Resume (Note 14) CFI Query (Note 15) AAA AAA 80 80 AAA AAA AA AA 555 555 55 55 AAA SADD 10 30 Legend: X = Don’t care RA = Address of the memory location to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE#f pulse, whichever happens later. Notes: 1. See Table 1 for description of bus operations. 2. 3. 4. 5. 6. 7. All values are in hexadecimal. Except for the read cycle and the fourth cycle of the autoselect command sequence, all bus cycles are write cycles. Data bits DQ15–DQ8 are don’t care in command sequences, except for RD and PD. Unless otherwise noted, address bits A20–A12 are don’t cares. No unlock or command cycles required when bank is in read mode. The Reset command is required to return to reading array data (or to the erase-suspend-read mode if previously in Erase Suspend) when a bank is in the autoselect mode, or if DQ5 goes high (while the bank is providing status information). The fourth cycle of the autoselect command sequence is a read cycle. The system must provide the bank address to obtain the manufacturer ID, device ID, or SecSi Sector factory protect information. Data bits DQ15–DQ8 are don’t care. See the Autoselect Command Sequence section for more information. The data is 80h for factory locked and 00h for not factory locked. PD = Data to be programmed at location PA. Data latches on the rising edge of WE# or CE#f pulse, whichever happens first. SADD = Address of the sector to be verified (in autoselect mode) or erased. Address bits A20–A12 uniquely select any sector. BA = Address of the bank that is being switched to autoselect mode, is in bypass mode, or is being erased. 11. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 12. The Unlock Bypass Reset command is required to return to reading array data when the bank is in the unlock bypass mode. 13. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation, and requires the bank address. 14. The Erase Resume command is valid only during the Erase Suspend mode, and requires the bank address. 15. Command is valid when device is ready to read array data or when device is in autoselect mode. 8. Table 17. Device Autoselect Device IDs (Byte Mode) Autoselect Device ID 55h (T), 56h (B) 50h (T), 53h (B) 5Ch (T), 5Fh (B) Am29DL322G Am29DL323G Am29DL324G 9. 10. The data is 00h for an unprotected sector/sector block and 01h for a protected sector/sector block. T = Top Boot Sector, B = Bottom Boot Sector 32 Am42DL32x4G May 19, 2003 PRELIMINARY WRITE OPERATION STATUS The device provides several bits to determine the status of a program or erase operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 18 and the following subsections describe the function of these bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to determine whether an Embedded Program or Erase operation is in progress or has been completed. pleted the program or erase operation and DQ7 has valid data, the data outputs on DQ6–DQ0 may be still invalid. Valid data on DQ7–DQ0 will appear on successive read cycles. Table 18 shows the outputs for Data# Polling on DQ7. Figure 5 shows the Data# Polling algorithm. Figure 22 in the AC Characteristics section shows the Data# Polling timing diagram. DQ7: Data# Polling The Data# Polling bit, DQ7, indicates to the host syst em w het he r an E mbe dde d Prog ra m or E ra se algorithm is in progress or completed, or whether a bank is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then that bank returns to reading array data. During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the bank enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the bank returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has comSTART Read DQ7–DQ0 Addr = VA DQ7 = Data? Yes No No DQ5 = 1? Yes Read DQ7–DQ0 Addr = VA DQ7 = Data? Yes No FAIL PASS Notes: 1. VA = Valid address for programming. During a sector erase operation, a valid address is any sector address within the sector being erased. During chip erase, a valid address is any non-protected sector address. 2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5. Figure 5. Data# Polling Algorithm May 19, 2003 Am42DL32x4G 33 PRELIMINARY RY/BY#: Ready/Busy# The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is reading array data, the standby mode, or one of the banks is in the erase-suspend-read mode. Table 18 shows the outputs for RY/BY#. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete. Table 18 shows the outputs for Toggle Bit I on DQ6. Figure 6 shows the toggle bit algorithm. Figure 23 in the “AC Characteristics” section shows the toggle bit timing diagrams. Figure 24 shows the differences between DQ2 and DQ6 in graphical form. See also the subsection on DQ2: Toggle Bit II. START Read DQ7–DQ0 DQ6: Toggle Bit I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE# or CE#f to control the read cycles. When the operation is complete, DQ6 stops toggling. After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling). If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program command sequence is written, then returns to reading array data. Read DQ7–DQ0 Toggle Bit = Toggle? Yes No No DQ5 = 1? Yes Read DQ7–DQ0 Twice Toggle Bit = Toggle? No Yes Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete Note: The system should recheck the toggle bit even if DQ5 = “1” because the toggle bit may stop toggling as DQ5 changes to “1.” See the subsections on DQ6 and DQ2 for more information. Figure 6. Toggle Bit Algorithm 34 Am42DL32x4G May 19, 2003 PRELIMINARY DQ2: Toggle Bit II The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE# or CE#f to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 18 to compare outputs for DQ2 and DQ6. Figure 6 shows the toggle bit algorithm in flowchart form, and the section “DQ2: Toggle Bit II” explains the algorithm. See also the DQ6: Toggle Bit I subsection. Figure 23 shows the toggle bit timing diagram. Figure 24 shows the differences between DQ2 and DQ6 in graphical form. cles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 6). DQ5: Exceeded Timing Limits DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase cycle was not successfully completed. The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was previously programmed to “0.” O nly an erase operation can change a “0” back to a “1.” Under this condition, the device halts the operation, and when the timing limit has been exceeded, DQ5 produces a “1.” Under both these conditions, the system must write the reset command to return to reading array data (or to the erase-suspend-read mode if a bank was previously in the erase-suspend-program mode). DQ3: Sector Erase Timer After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be assumed to be less than 50 µs, the system need not monitor DQ3. See also the Sector Erase Command Sequence section. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device will accept additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 18 shows the status of DQ3 relative to the other status bits. Reading Toggle Bits DQ6/DQ2 Refer to Figure 6 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cy- May 19, 2003 Am42DL32x4G 35 PRELIMINARY Table 18. Status Standard Mode Erase Suspend Mode Embedded Program Algorithm Embedded Erase Algorithm Erase Erase-Suspend- Suspended Sector Read Non-Erase Suspended Sector Erase-Suspend-Program Write Operation Status DQ7 (Note 2) DQ7# 0 1 Data DQ7# DQ6 Toggle Toggle No toggle Data Toggle DQ5 (Note 1) 0 0 0 Data 0 DQ3 N/A 1 N/A Data N/A DQ2 (Note 2) No toggle Toggle Toggle Data N/A RY/BY# 0 0 1 1 0 Notes: 1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. Refer to the section on DQ5 for more information. 2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. 3. When reading write operation status bits, the system must always provide the bank address where the Embedded Algorithm is in progress. The device outputs array data if the system addresses a non-busy bank. 36 Am42DL32x4G May 19, 2003 PRELIMINARY ABSOLUTE MAXIMUM RATINGS Storage Temperature Plastic Packages . . . . . . . . . . . . . . . –55°C to +125°C Ambient Temperature with Power Applied . . . . . . . . . . . . . . –40°C to +85°C Voltage with Respect to Ground VCCf/VCCs (Note 1) . . . . . . . . . . . . –0.3 V to +4.0 V RESET# (Note 2) . . . . . . . . . . . . –0.5 V to +12.5 V WP#/ACC . . . . . . . . . . . . . . . . . . –0.5 V to +10.5 V All other pins (Note 1) . . . . . . –0.5 V to VCC +0.5 V Output Short Circuit Current (Note 3) . . . . . . 200 mA Notes: 1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may overshoot V SS t o –2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. See Figure 7. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 8. 2. Minimum DC input voltage on pins OE#, RESET#, and WP#/ACC is –0.5 V. During voltage transitions, OE#, WP#/ACC, and RESET# may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 7. Maximum DC input voltage on pin RESET# is +12.5 V which may overshoot to +14.0 V for periods up to 20 ns. Maximum DC input voltage on WP#/ACC is +9.5 V which may overshoot to +12.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. VCC +2.0 V VCC +0.5 V 2.0 V 20 ns 20 ns 20 ns 20 ns +0.8 V –0.5 V –2.0 V 20 ns Figure 7. Maximum Negative Overshoot Waveform 20 ns Figure 8. Maximum Positive Overshoot Waveform OPERATING RANGES Industrial (I) Devices Ambient Temperature (TA) . . . . . . . . . –40°C to +85°C VCCf/VCCs Supply Voltage VCCf/VCCs for standard voltage range . . 2.7 V to 3.3 V Operating ranges define those limits between which the functionality of the device is guaranteed. May 19, 2003 Am42DL32x4G 37 PRELIMINARY DC CHARACTERISTICS CMOS Compatible Parameter Symbol ILI ILIT ILO ILIA Parameter Description Input Load Current RESET# Input Load Current Output Leakage Current ACC Input Leakage Current Test Conditions VIN = VSS to VCC, VCC = VCC max VCC = VCC max; RESET# = 12.5 V VOUT = VSS to VCC, VCC = VCC max VCC = VCC max, WP#/ACC = VACC max CE#f = VIL, OE# = VIH, Byte Mode CE#f = VIL, OE# = VIH, Word Mode 5 MHz 1 MHz 5 MHz 1 MHz 10 2 10 2 15 0.2 0.2 0.2 21 21 21 21 17 –0.2 2.4 8.5 Min Typ Max ±1.0 35 ±1.0 35 16 4 16 4 30 5 5 5 45 45 45 45 35 0.6 VCC + 0.2 9.5 mA mA µA µA µA mA Unit µA µA µA µA ICC1f Flash VCC Active Read Current (Notes 1, 2) Flash VCC Active Write Current (Notes 2, 3) Flash VCC Standby Current (Note 2) Flash VCC Reset Current (Note 2) Flash VCC Current Automatic Sleep Mode (Notes 2, 4) ICC2f ICC3f ICC4f ICC5f ICC6f ICC7f ICC8f VIL VIH VHH CE#f = VIL, OE# = VIH, WE# = VIL VCCf = VCC max, CE#f, RESET#, WP#/ACC = VCCf ± 0.3 V VCCf = VCC max, RESET# = VSS ± 0.3 V, WP#/ACC = VCCf ± 0.3 V VCCf = VCC max, VIH = VCC ± 0.3 V; VIL = VSS ± 0.3 V Byte Word Byte Word Flash VCC Active Read-While-Program Current (Notes CE#f = VIL, OE# = VIH 1, 2) Flash VCC Active Read-While-Erase Current (Notes 1, 2) Flash VCC Active Program-While-Erase-Suspended Current (Notes 2, 5) Input Low Voltage Input High Voltage Voltage for WP#/ACC Program Acceleration and Sector Protection/Unprotection Voltage for Sector Protection, Autoselect and Temporary Sector Unprotect Output Low Voltage CE#f = VIL, OE# = VIH CE#f = VIL, OE#f = VIH mA mA V V V VID VOL VOH1 VOH2 VLKO 11.5 IOL = 4.0 mA, VCCf = VCCs = VCC min IOH = –2.0 mA, VCCf = VCCs = VCC min IOH = –100 µA, VCC = VCC min 0.85 x VCC VCC–0.4 2.3 12.5 0.45 V V Output High Voltage Flash Low VCC Lock-Out Voltage (Note 5) V 2.5 V Notes: 1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. 2. Maximum ICC specifications are tested with VCC = VCCmax. 3. ICC active while Embedded Erase or Embedded Program is in progress. 4. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. Typical sleep mode current is 200 nA. 5. Not 100% tested. 38 Am42DL32x4G May 19, 2003 PRELIMINARY SRAM DC AND OPERATING CHARACTERISTICS Parameter Symbol ILI ILO ICC Parameter Description Input Leakage Current Output Leakage Current Operating Power Supply Current Test Conditions VIN = VSS to VCC CE1#s = VIH, CE2s = VIL or OE# = VIH or WE# = VIL, VIO= VSS to VCC IIO = 0 mA, CE1#s = VIL, CE2s = WE# = VIH, VIN = VIH or VIL Cycle time = 1 µs, 100% duty, IIO = 0 mA, CE1#s ≤ 0.2 V, CE2 ≥ VCC – 0.2 V, VIN ≤ 0.2 V or VIN ≥ VCC – 0.2 V Cycle time = Min., IIO = 0 mA, 100% duty, CE1#s = VIL, CE2s = VIH, VIN = VIL = or VIH Min –1.0 –1.0 55 70 55 70 55 70 –0.2 (Note 1) 2.2 IOL = 2.1 mA IOH = –1.0 mA CE1#s = VIH, CE2 = VIL, Other inputs = VIH or VIL CE1#s ≥ VCC – 0.2 V, CE2 ≥ VCC – 0.2 V (CE1#s controlled) or CE2 ≤ 0.2 V (CE2s controlled), CIOs = VSS or VCC, Other input = 0 ~ VCC 2.4 0.3 Typ Max 1.0 1.0 5 3 30 mA 22 5 3 0.4 VCC+0.2 (Note 2) 0.4 mA mA Unit µA µA ICC1s Average Operating Current ICC2s Average Operating Current VIL VIH VOL VOH ISB Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage Standby Current (TTL) V V V V mA ISB1 Standby Current (CMOS) 10 µA Notes: 1. Undershoot: –1.0V if pulse width ≤ 20 ns. 2. Overshoot: VCC+1.0V if pulse width ≤ 20 ns. May 19, 2003 Am42DL32x4G 39 PRELIMINARY DC CHARACTERISTICS Zero-Power Flash 25 Supply Current in mA 20 15 10 5 0 0 500 1000 1500 2000 Time in ns 2500 3000 3500 4000 Note: Addresses are switching at 1 MHz Figure 9. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents) 12 3.3 V 10 2.7 V 8 Supply Current in mA 6 4 2 0 1 Note: T = 25 °C 2 3 Frequency in MHz Figure 10. Typical ICC1 vs. Frequency 4 5 40 Am42DL32x4G May 19, 2003 PRELIMINARY TEST CONDITIONS Table 19. 3.3 V 2.7 kΩ Test Specifications All Speeds Unit Test Condition Output Load Output Load Capacitance, CL (including jig capacitance) 1 TTL gate 30 5 0.0–3.0 1.5 1.5 pF ns V V V Device Under Test CL 6.2 kΩ Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels Note: Diodes are IN3064 or equivalent Output timing measurement reference levels Figure 11. Test Setup KEY TO SWITCHING WAVEFORMS WAVEFORM INPUTS Steady Changing from H to L Changing from L to H Don’t Care, Any Change Permitted Does Not Apply Changing, State Unknown Center Line is High Impedance State (High Z) OUTPUTS KS000010-PAL 2.0 V 0.0 V Input 1.0 V Measurement Level 1.0 V Output Figure 12. Input Waveforms and Measurement Levels May 19, 2003 Am42DL32x4G 41 PRELIMINARY AC CHARACTERISTICS SRAM CE#s Timing Parameter Test Setup JEDEC — Std tCCR Description CE#s Recover Time — Min 0 ns All Speeds Unit CE#f tCCR CE1#s tCCR tCCR CE2s tCCR Figure 13. Timing Diagram for Alternating Between SRAM to Flash 42 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS Flash Read-Only Operations Parameter Test Setup JEDEC tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX Std tRC tACC tCE tOE tDF tDF tOH Description Read Cycle Time (Note 1) Address to Output Delay Chip Enable to Output Delay Output Enable to Output Delay Chip Enable to Output High Z (Note 1) Output Enable to Output High Z (Note 1) Output Hold Time From Addresses, CE#f or OE#, Whichever Occurs First Read Output Enable Hold Time Toggle and (Note 1) Data# Polling CE#f, OE# = VIL OE# = VIL Min Max Max Max Max Max Min Min Min 70, 71 70 70 70 30 16 16 0 0 10 85 85 85 85 40 ns ns ns ns ns ns ns ns ns Speed Options Unit tOEH Notes: 1. Not 100% tested. 2. See Figure 11 and Table 19 for test specifications. tRC Addresses CE#f tRH tRH OE# tOEH WE# HIGH Z Outputs RESET# RY/BY# Output Valid tCE tOH HIGH Z tOE tDF Addresses Stable tACC 0V Figure 14. Read Operation Timings May 19, 2003 Am42DL32x4G 43 PRELIMINARY AC CHARACTERISTICS Hardware Reset (RESET#) Parameter Description JEDEC Std tReady tReady tRP tRH tRPD tRB RESET# Pin Low (During Embedded Algorithms) to Read Mode (See Note) RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode (See Note) RESET# Pulse Width Reset High Time Before Read (See Note) RESET# Low to Standby Mode RY/BY# Recovery Time Max Max Min Min Min Min 20 500 500 50 20 0 µs ns ns ns µs ns All Speeds Unit Note: Not 100% tested. RY/BY# CE#f, OE# tRH RESET# tRP tReady Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms tReady RY/BY# tRB CE#f, OE# RESET# tRP Figure 15. Reset Timings 44 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS Flash Word/Byte Configuration (CIOf) Parameter JEDEC Std tELFL/tELFH tFLQZ tFHQV Description CE#f to CIOf Switching Low or High CIOf Switching Low to Output HIGH Z CIOf Switching High to Output Active Max Max Min 70 Speed Options Unit 70, 71 5 16 85 85 ns ns ns CE#f OE# CIOf tELFL DQ14–DQ0 CIOf Switching from word to byte mode Data Output (DQ14–DQ0) Data Output (DQ7–DQ0) Address Input DQ15/A-1 DQ15 Output tFLQZ tELFH CIOf CIOf Switching from byte to word mode DQ14–DQ0 Data Output (DQ7–DQ0) Address Input tFHQV Data Output (DQ14–DQ0) DQ15 Output DQ15/A-1 Figure 16. CE#f CIOf Timings for Read Operations The falling edge of the last WE# signal WE# CIOf tSET (tAS) tHOLD (tAH) Note: Refer to the Erase/Program Operations table for tAS and tAH specifications. Figure 17. CIOf Timings for Write Operations May 19, 2003 Am42DL32x4G 45 PRELIMINARY AC CHARACTERISTICS Flash Erase and Program Operations Parameter JEDEC tAVAV tAVWL Std tWC tAS tASO tWLAX tAH tAHT tDVWH tWHDX tDS tDH tOEH tOEPH tGHEL tGHWL tWLEL tELWL tEHWH tWHEH tWLWH tELEH tWHDL tGHEL tGHWL tWS tCS tWH tCH tWP tCP tWPH tSR/W tWHWH1 tWHWH1 Description Write Cycle Time (Note 1) Address Setup Time (WE# to Address) Address Setup Time to OE# or CE#f Low During Toggle Bit Polling Address Hold Time (WE# to Address) Address Hold Time From CE#f or OE# High During Toggle Bit Polling Data Setup Time Data Hold Time Read OE# Hold Time Toggle and Data# Polling Output Enable High During Toggle Bit Polling Read Recovery Time Before Write (OE# High to CE#f Low) Read Recovery Time Before Write (OE# High to WE# Low) WE# Setup Time (CE#f to WE#) CE#f Setup Time (WE# to CE#f) WE# Hold Time (CE#f to WE#) CE#f Hold Time (CE#f to WE#) Write Pulse Width CE#f Pulse Width Write Pulse Width High Latency Between Read and Write Operations Byte Programming Operation (Note 2) Word Accelerated Programming Operation, Word or Byte (Note 2) Sector Erase Operation (Note 2) VCCf Setup Time (Note 1) Write Recovery Time From RY/BY# Program/Erase Valid To RY/BY# Delay Typ Typ Typ Min Min Max 7 4 0.4 50 0 90 µs sec µs ns ns Min Min Min Min Min Min Min Min Min Min Min Min Typ 30 30 30 0 5 µs 10 20 0 0 0 0 0 0 35 35 ns ns ns ns ns ns ns ns ns ns ns ns Min Min Min Min Min Min Min Min 35 0 0 Speed Options Unit 70, 71 70 0 15 45 0 45 85 85 ns ns ns ns ns ns ns ns tWHWH1 tWHWH2 tWHWH1 tWHWH2 tVCS tRB tBUSY Notes: 1. Not 100% tested. 2. See the “Flash Erase And Programming Performance” section for more information. 46 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS Program Command Sequence (last two cycles) tWC Addresses 555h tAS PA tAH CE#f tGHWL OE# tWP WE# tCS tDS Data tDH PD tBUSY RY/BY# Status DOUT tRB tWPH tWHWH1 PA PA Read Status Data (last two cycles) tCH A0h VCCf tVCS Notes: 1. PA = program address, PD = program data, DOUT is the true data at the program address. 2. Illustration shows device in word mode. Figure 18. Program Operation Timings VHH WP#/ACC VIL or VIH tVHH tVHH VIL or VIH Figure 19. Accelerated Program Timing Diagram May 19, 2003 Am42DL32x4G 47 PRELIMINARY AC CHARACTERISTICS Erase Command Sequence (last two cycles) tWC Addresses 2AAh tAS SADD 555h for chip erase Read Status Data VA tAH VA CE#f tGHWL OE# tWP WE# tCS tDS tDH Data 55h 30h 10 for Chip Erase In Progress Complete tCH tWPH tWHWH2 tBUSY RY/BY# tVCS VCCf tRB Notes: 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”). 2. These waveforms are for the word mode. Figure 20. Chip/Sector Erase Operation Timings 48 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS tWC Addresses Valid PA tRC Valid RA tWC Valid PA tWC Valid PA tAH tACC CE#f tCPH tCE tOE tCP OE# tOEH tWP WE# tWPH tDS tDH Data Valid In tGHWL tDF tOH Valid Out Valid In Valid In tSR/W WE# Controlled Write Cycle Read Cycle CE#f Controlled Write Cycles Figure 21. Back-to-back Read/Write Cycle Timings tRC Addresses VA tACC tCE CE#f tCH OE# tOEH WE# tOH DQ7 High Z VA VA tOE tDF Complement Complement True Valid Data High Z DQ0–DQ6 tBUSY RY/BY# Status Data Status Data True Valid Data Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle. Figure 22. Data# Polling Timings (During Embedded Algorithms) May 19, 2003 Am42DL32x4G 49 PRELIMINARY AC CHARACTERISTICS tAHT Addresses tAHT tASO CE#f tOEH WE# tOEPH OE# tDH DQ6/DQ2 Valid Data Valid Status tAS tCEPH tOE Valid Status Valid Status Valid Data (first read) RY/BY# (second read) (stops toggling) Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle Figure 23. Enter Embedded Erasing WE# Toggle Bit Timings (During Embedded Algorithms) Erase Suspend Erase Enter Erase Suspend Program Erase Suspend Program Erase Resume Erase Suspend Read Erase Erase Complete Erase Suspend Read DQ6 DQ2 Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE#f to toggle DQ2 and DQ6. Figure 24. DQ2 vs. DQ6 50 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS Temporary Sector/Sector Block Unprotect Parameter All Speed Options JEDEC Std tVIDR tVHH tRSP tRRB Description VID Rise and Fall Time (See Note) VHH Rise and Fall Time (See Note) RESET# Setup Time for Temporary Sector/Sector Block Unprotect RESET# Hold Time from RY/BY# High for Temporary Sector/Sector Block Unprotect Min Min Min Min 500 250 4 4 ns ns µs µs Unit Note: Not 100% tested. VID RESET# VSS, VIL, or VIH tVIDR Program or Erase Command Sequence CE#f tVIDR VID VSS, VIL, or VIH WE# tRSP RY/BY# tRRB Figure 25. Temporary Sector/Sector Block Unprotect Timing Diagram May 19, 2003 Am42DL32x4G 51 PRELIMINARY AC CHARACTERISTICS VID VIH RESET# SADD, A6, A1, A0 Valid* Sector/Sector Block Protect or Unprotect Valid* Verify 40h Sector/Sector Block Protect: 150 µs, Sector/Sector Block Unprotect: 15 ms Valid* Data 60h 60h Status 1 µs CE#f WE# OE# * For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0. Figure 26. Sector/Sector Block Protect and Unprotect Timing Diagram 52 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS Alternate CE#f Controlled Erase and Program Operations Parameter JEDEC tAVAV tAVWL Std tWC tAS tASO tELAX tAH tAHT tDVEH tEHDX tGHEL tWLEL tEHWH tELEH tEHEL tWHWH1 tDS tDH tGHEL tWS tWH tCP tCPH tWHWH1 Description Write Cycle Time (Note 1) Address Setup Time (WE# to Address) Address Setup Time to CE#f Low During Toggle Bit Polling Address Hold Time Address Hold time from CE#f or OE# High During Toggle Bit Polling Data Setup Time Data Hold Time Read Recovery Time Before Write (OE# High to WE# Low) WE# Setup Time WE# Hold Time CE#f Pulse Width CE#f Pulse Width High Programming Operation (Note 2) Byte Word Min Min Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Typ 30 30 5 µs 7 4 0.4 µs sec 35 0 0 0 0 35 Speed Options Unit 70, 71 70 0 15 45 0 45 85 85 ns ns ns ns ns ns ns ns ns ns ns ns tWHWH1 tWHWH2 tWHWH1 tWHWH2 Accelerated Programming Operation, Word or Byte (Note 2) Sector Erase Operation (Note 2) Notes: 1. Not 100% tested. 2. See the “Flash Erase And Programming Performance” section for more information. May 19, 2003 Am42DL32x4G 53 PRELIMINARY AC CHARACTERISTICS 555 for program 2AA for erase PA for program SADD for sector erase 555 for chip erase Data# Polling PA Addresses tWC tWH WE# tGHEL OE# tCP CE#f tWS tCPH tDS tDH Data tRH A0 for program 55 for erase PD for program 30 for sector erase 10 for chip erase tAS tAH tWHWH1 or 2 tBUSY DQ7# DOUT RESET# RY/BY# Notes: 1. Figure indicates last two bus cycles of a program or erase operation. 2. PA = program address, SA = sector address, PD = program data. 3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device. 4. Waveforms are for the word mode. Figure 27. Flash Alternate CE#f Controlled Write (Erase/Program) Operation Timings 54 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS SRAM Read Cycle Parameter Symbol tRC tAA tCO1, tCO2 tOE tBA tLZ1, tLZ2 tBLZ tOLZ tHZ1, tHZ2 tBHZ tOHZ tOH Speed Options Description 70, 85 Read Cycle Time Address Access Time Chip Enable to Output Output Enable Access Time LB#s, UB#s to Access Time Chip Enable (CE1#s Low and CE2s High) to Low-Z Output UB#, LB# Enable to Low-Z Output Output Enable to Low-Z Output Chip Disable to High-Z Output UB#s, LB#s Disable to High-Z Output Output Disable to High-Z Output Output Data Hold from Address Change Min Max Max Max Max Min Min Min Max Max Max Min 25 25 25 10 70 70 70 35 70 10 10 5 20 20 20 71 55 55 55 25 55 ns ns ns ns ns ns ns ns ns ns ns ns Unit tRC Address tOH Data Out Previous Data Valid tAA Data Valid Note: CE1#s = OE# = VIL, CE2s = WE# = VIH, UB#s and/or LB#s = VIL Figure 28. SRAM Read Cycle—Address Controlled May 19, 2003 Am42DL32x4G 55 PRELIMINARY AC CHARACTERISTICS tRC Address tAA tCO1 tOH CE#1s CE2s tCO2 tOE tOLZ tBLZ tLZ tHZ OE# tOHZ Data Valid Data Out High-Z Figure 29. Notes: 1. WE# = VIH. WE# remains high for the read cycle. SRAM Read Cycle 2. tHZ and tOHZ are defined as the time at which the outputs achieve the open circuit conditions and are not referenced to output voltage levels. 3. At any given temperature and voltage condition, tHZ (Max.) is less than tLZ (Min.) both for a given device and from device to device interconnection. 56 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS SRAM Write Cycle Parameter Symbol tWC tCw tAS tAW tBW tWP tWR tWHZ tDW tDH tOW Description Write Cycle Time Chip Enable to End of Write Address Setup Time Address Valid to End of Write UB#s, LB#s to End of Write Write Pulse Time Write Recovery Time Write to Output High-Z Data to Write Time Overlap Data Hold from Write Time End Write to Output Low-Z Min Min Min Min Min Min Min Min Max Min Min min 0 20 30 0 5 60 60 50 0 0 20 25 Speed Options 70, 85 70 60 0 45 45 40 71 55 45 Unit ns ns ns ns ns ns ns ns ns ns ns tWC Address tCW (See Note 2) tAW CS2s UB#s, LB#s tCW (See Note 2) tBW tWP (See Note 5) tAS (See Note 4) (See Note 9) High-Z tWHZ Data Out (See Note 6) tDW Data Valid tWR (See Note 3) CS1#s WE# tDH Data In (See Note 9) High-Z tOW (See Note 7) Notes: 1. WE# controlled. 2. tCW is measured from CE1#s going low to the end of write. 3. tWR is measured from the end of write to the address change. tWR applied in case a write ends as CE1#s or WE# going high. 4. tAS is measured from the address valid to the beginning of write. 5. A write occurs during the overlap (tWP) of low CE#1 and low WE#. A write begins when CE1#s goes low and WE# goes low when asserting UB#s or LB#s for a single byte operation or simultaneously asserting UB#s and LB#s for a double byte operation. A write ends at the earliest transition when CE1#s goes high and WE# goes high. The tWP is measured from the beginning of write to the end of write. 6. If CE1# goes low (or CE2 goes high) at the same time or after WE# goes low, the outputs will remain at high impedance. 7. If CE1# goes high (or CE2 goes low) at the same time or before WE# goes high, the outputs will remain at high impedance. 8. If OE# is high during the write cycle, the outputs will remain at high impedance. 9. Output data may be present on the bus at this time; input signals should not be applied. Figure 30. SRAM Write Cycle—WE# Control May 19, 2003 Am42DL32x4G 57 PRELIMINARY AC CHARACTERISTICS tWC Address tAS (See Note 2) t CW (See Note 3) CE1#s tAW CE2s tBW tWP (See Note 5) WE# tDW Data In (See Note 6) tDH tWR (See Note 4) UB#s, LB#s Data Valid Data Out High-Z High-Z Notes: 1. CE1#s controlled. 2. tCW is measured from CE1#s going low to the end of write. 3. tWR is measured from the end of write to the address change. tWR applied in case a write ends as CE1#s or WE# going high. 4. tAS is measured from the address valid to the beginning of write. 5. A write occurs during the overlap (tWP) of low CE#1 and low WE#. A write begins when CE1#s goes low and WE# goes low when asserting UB#s or LB#s for a single byte operation or simultaneously asserting UB#s and LB#s for a double byte operation. A write ends at the earliest transition when CE1#s goes high and WE# goes high. The tWP is measured from the beginning of write to the end of write. 6. Output data may be present on the bus at this time; input signals should not be applied. 7. If OE# is high during the write cycle, the outputs will remain at high impedance. Figure 31. SRAM Write Cycle—CE1#s Control 58 Am42DL32x4G May 19, 2003 PRELIMINARY AC CHARACTERISTICS tWC Address tCW (See Note 2) tAW CE2s UB#s, LB#s tCW (See Note 2) tBW tAS (See Note 4) tWP (See Note 5) tDW Data In (See Note 6) tDH tWR (See Note 3) CE1#s WE# Data Valid Data Out High-Z High-Z Notes: 1. UB#s and LB#s controlled. 2. tCW is measured from CE1#s going low to the end of write. 3. tWR is measured from the end of write to the address change. tWR applied in case a write ends as CE1#s or WE# going high. 4. tAS is measured from the address valid to the beginning of write. 5. A write occurs during the overlap (tWP) of low CE#1 and low WE#. A write begins when CE1#s goes low and WE# goes low when asserting UB#s or LB#s for a single byte operation or simultaneously asserting UB#s and LB#s for a double byte operation. A write ends at the earliest transition when CE1#s goes high and WE# goes high. The tWP is measured from the beginning of write to the end of write. 6. Output data may be present on the bus at this time; input signals should not be applied. 7. If OE# is high during the write cycle, the outputs will remain at high impedance. Figure 32. SRAM Write Cycle—UB#s and LB#s Control May 19, 2003 Am42DL32x4G 59 PRELIMINARY Flash Erase And Programming Performance Parameter Sector Erase Time Chip Erase Time Byte Program Time Word Program Time Accelerated Byte/Word Program Time Chip Program Time (Note 3) Byte Mode Word Mode Typ (Note 1) 0.4 28 5 7 4 21 14 150 210 120 63 sec 42 Max (Note 2) 5 Unit sec sec µs µs µs Excludes system level overhead (Note 5) Comments Excludes 00h programming prior to erasure (Note 4) Notes: 1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 1,000,000 cycles. Additionally, programming typicals assume checkerboard pattern. 2. Under worst case conditions of 90°C, VCC = 2.7 V, 1,000,000 cycles. 3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes program faster than the maximum program times listed. 4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure. 5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Tables 14 and 16 or further information on command definitions. 6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles. FLASH LATCHUP CHARACTERISTICS Description Input voltage with respect to VSS on all pins except I/O pins (including OE#, and RESET#) Input voltage with respect to VSS on all I/O pins VCC Current Min –1.0 V –1.0 V –100 mA Max 12.5 V VCC + 1.0 V +100 mA Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time. PACKAGE PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 CIN3 Description Input Capacitance Output Capacitance Control Pin Capacitance WP#/ACC Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 VIN = 0 Typ 11 12 14 17 Max 14 16 16 20 Unit pF pF pF pF Note: 7.Test conditions TA = 25°C, f = 1.0 MHz. FLASH DATA RETENTION Parameter Description Minimum Pattern Data Retention Time Test Conditions 150°C 125°C Min 10 20 Unit Years Years 60 Am42DL32x4G May 19, 2003 PRELIMINARY SRAM DATA RETENTION Parameter Symbol VDR IDR tSDR tRDR Parameter Description VCC for Data Retention Data Retention Current Data Retention Set-Up Time Recovery Time Test Setup CS1#s ≥ VCC – 0.2 V (Note 1) VCC = 3.0 V, CE1#s ≥ VCC – 0.2 V (Note 1) See data retention waveforms 0 tRC Min 1.5 1.0 (Note 2) Typ Max 3.3 10 Unit V µA ns ns Notes: 1. CE1#s ≥ VCC – 0.2 V, CE2s ≥ VCC – 0.2 V (CE1#s controlled) or CE2s ≤ 0.2 V (CE2s controlled). 2. Typical values are not 100% tested. VCC 2.7V tSDR Data Retention Mode tRDR 2.2V VDR CE1#s GND CE1#s ≥ VCC - 0.2 V Figure 33. CE1#s Controlled Data Retention Mode Data Retention Mode VCC 2.7 V CE2s tSDR tRDR VDR 0.4 V GND CE2s < 0.2 V Figure 34. CE2s Controlled Data Retention Mode May 19, 2003 Am42DL32x4G 61 PRELIMINARY PHYSICAL DIMENSIONS FLB073—73-Ball Fine-Pitch Grid Array 8 x 11.6 mm 62 Am42DL32x4G May 19, 2003 PRELIMINARY REVISION SUMMARY Revision A (January 9, 2002) Initial release. Changed CFI website address. Customer Lockable: SecSi Sector NOT Programmed or Protected at the factory. Added second bullet, SecSi sector-protect verify text and figure 3. SecSi Sector Flash Memory Region, and Enter SecSi Sector/Exit SecSi Sector Command Sequence Noted that the ACC function and unlock bypass modes are not available when the SecSi sector is enabled. Byte/Word Program Command Sequence, Sector Erase Command Sequence, and Chip Erase Command Sequence Noted that the SecSi Sector, autoselect, and CFI functions are unavailable when a program or erase operation is in progress. Revision A + 1 (September 30, 2002) Connection Diagram Changed H7 from NC to DQ13. Logic Symbol Changed from 19 to 18 address inputs for A17 to A0. Sector/Sector Block Protection and Unprotection Added bottom boot sector protection table. Common Flash Memory Interface (CFI) Changed third paragraph to indicate that the system must write reset command to return to reading array data, not the autoselect mode. Changed URL for CFI documents. DC Characteristics, CMOS Compatible Removed IACC from table. SRAM DC and Operating Characteristics Added VIL and VIH to table. Revision A + 3 (February 7, 2003) Product Selector Guide Corrected typo in Speed Option. Revision A + 4 (March 14, 2003) Product Selector Guide Corrected typo in SRAM Speed Option and updated tables in datasheet to reflect correction. Revision A + 2 (February 5, 2003) Global Added the 75 speed option to Flash memory and SRAM throughout the datasheet. Removed the 85 ns speed option in SRAM. Ordering Information Added order numbers to reflect the new speed option. Common Flash Memory Interface (CFI) Revision B (May 19, 2003) Global Removed “Pseudo” from data sheet. Removed 75 ns speed option and added 71 ns speed option. Then, corrected ordering information to reflect change. Trademarks Copyright © 2003 Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc. ExpressFlash is a trademark of Advanced Micro Devices, Inc. Product names used in this publication are for identification purposes only and may be trademarks of their respective companies. May 19, 2003 Am42DL32x4G 63 Sales Offices and Representatives North America ALABAMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 2 5 6 ) 8 3 0 - 9 1 9 2 ARIZONA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 6 0 2 ) 24 2 - 4 4 0 0 CALIFORNIA, Irvine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 9 4 9 ) 4 5 0 - 7 5 0 0 Sunnyvale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 4 0 8 ) 7 3 2 - 24 0 0 COLORADO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 3 0 3 ) 74 1 - 2 9 0 0 CONNECTICUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 2 0 3 ) 2 6 4 - 7 8 0 0 FLORIDA, Clearwater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 2 7 ) 7 9 3 - 0 0 5 5 Miami (Lakes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 3 0 5 ) 8 2 0 - 1 1 1 3 GEORGIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 7 0 ) 8 1 4 - 0 2 2 4 ILLINOIS, Chicago . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 6 3 0 ) 7 7 3 - 4 4 2 2 MASSACHUSETTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 8 1 ) 2 1 3 - 6 4 0 0 MICHIGAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 2 4 8 ) 4 7 1 - 6 2 9 4 MINNESOTA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 6 1 2 ) 74 5 - 0 0 0 5 NEW JERSEY, Chatham . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 9 7 3 ) 7 0 1 - 1 7 7 7 NEW YORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 1 6 ) 4 2 5 - 8 0 5 0 NORTH CAROLINA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 9 1 9 ) 8 4 0 - 8 0 8 0 OREGON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 5 0 3 ) 24 5 - 0 0 8 0 PENNSYLVANIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 2 1 5 ) 3 4 0 - 1 1 8 7 SOUTH DAKOTA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 6 0 5 ) 69 2 - 5 7 7 7 TEXAS, Austin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 5 1 2 ) 3 4 6 - 7 8 3 0 Dallas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 9 7 2 ) 9 8 5 - 1 3 4 4 Houston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 2 8 1 ) 3 76 - 8 0 8 4 VIRGINIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 0 3 ) 7 3 6 - 9 5 6 8 Representatives in U.S. and Canada ARIZONA, Tempe - Centaur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 4 8 0 ) 8 3 9 - 2 3 2 0 CALIFORNIA, Calabasas - Centaur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 8 1 8 ) 8 7 8 - 5 8 0 0 Irvine - Centaur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 9 4 9 ) 2 6 1 - 2 1 2 3 San Diego - Centaur. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 8 5 8 ) 2 7 8 - 4 9 5 0 Santa Clara - Fourfront. . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 4 0 8 ) 3 5 0 - 4 8 0 0 CANADA, Burnaby, B.C. - Davetek Marketing. . . . . . . . . . . . . . . . . . . . ( 6 0 4 ) 4 3 0 - 3 6 8 0 Calgary, Alberta - Davetek Marketing. . . . . . . . . . . . . . . . . ( 4 0 3 ) 2 8 3 - 3 5 7 7 Kanata, Ontario - J-Squared Tech. . . . . . . . . . . . . . . . . . . . ( 6 1 3 ) 5 9 2 - 9 5 4 0 Mississauga, Ontario - J-Squared Tech. . . . . . . . . . . . . . . . . . ( 9 0 5 ) 6 7 2 - 2 0 3 0 St Laurent, Quebec - J-Squared Tech. . . . . . . . . . . . . . . . ( 5 1 4 ) 7 4 7 - 1 2 1 1 COLORADO, Golden - Compass Marketing . . . . . . . . . . . . . . . . . . . . . . ( 3 0 3 ) 2 7 7 - 0 4 5 6 FLORIDA, Melbourne - Marathon Technical Sales . . . . . . . . . . . . . . . . ( 3 2 1 ) 7 2 8 - 7 7 0 6 Ft. Lauderdale - Marathon Technical Sales . . . . . . . . . . . . . . ( 9 5 4 ) 5 2 7 - 4 9 4 9 Orlando - Marathon Technical Sales . . . . . . . . . . . . . . . . . . ( 4 0 7 ) 8 7 2 - 5 7 7 5 St. Petersburg - Marathon Technical Sales . . . . . . . . . . . . . . ( 7 2 7 ) 8 9 4 - 3 6 0 3 GEORGIA, Duluth - Quantum Marketing . . . . . . . . . . . . . . . . . . . . . ( 6 7 8 ) 5 8 4 - 1 1 2 8 ILLINOIS, Skokie - Industrial Reps, Inc. . . . . . . . . . . . . . . . . . . . . . . . . ( 8 4 7 ) 9 6 7 - 8 4 3 0 INDIANA, Kokomo - SAI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 6 5 ) 4 5 7 - 7 2 4 1 IOWA, Cedar Rapids - Lorenz Sales . . . . . . . . . . . . . . . . . . . . . . ( 3 1 9 ) 2 9 4 - 1 0 0 0 KANSAS, Lenexa - Lorenz Sales . . . . . . . . . . . . . . . . . . . . . . . . . ( 9 1 3 ) 4 6 9 - 1 3 1 2 MASSACHUSETTS, Burlington - Synergy Associates . . . . . . . . . . . . . . . . . . . . . ( 7 8 1 ) 2 3 8 - 0 8 7 0 MICHIGAN, Brighton - SAI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 8 1 0 ) 2 2 7 - 0 0 0 7 MINNESOTA, St. Paul - Cahill, Schmitz & Cahill, Inc. . . . . . . . . . . . . . . . . . ( 6 5 1 ) 69 9 - 0 2 0 0 MISSOURI, St. Louis - Lorenz Sales . . . . . . . . . . . . . . . . . . . . . . . . . . ( 3 1 4 ) 9 9 7 - 4 5 5 8 NEW JERSEY, Mt. Laurel - SJ Associates . . . . . . . . . . . . . . . . . . . . . . . . . ( 8 5 6 ) 8 6 6 - 1 2 3 4 NEW YORK, Buffalo - Nycom, Inc. . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 1 6 ) 7 4 1 - 7 1 1 6 East Syracuse - Nycom, Inc. . . . . . . . . . . . . . . . . . . . . . . ( 3 1 5 ) 4 3 7 - 8 3 4 3 Pittsford - Nycom, Inc. . . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 1 6 ) 5 8 6 - 3 6 6 0 Rockville Centre - SJ Associates . . . . . . . . . . . . . . . . . . . . ( 5 1 6 ) 5 3 6 - 4 2 4 2 NORTH CAROLINA, Raleigh - Quantum Marketing . . . . . . . . . . . . . . . . . . . . . . ( 9 1 9 ) 8 4 6 - 5 7 2 8 OHIO, Middleburg Hts - Dolfuss Root & Co. . . . . . . . . . . . . . . . . ( 4 4 0 ) 8 1 6 - 1 6 6 0 Powell - Dolfuss Root & Co. . . . . . . . . . . . . . . . . . . . . . . ( 6 1 4 ) 7 8 1 - 0 7 2 5 Vandalia - Dolfuss Root & Co. . . . . . . . . . . . . . . . . . . . . . ( 9 3 7 ) 8 9 8 - 9 6 1 0 Westerville - Dolfuss Root & Co. . . . . . . . . . . . . . . . . . . ( 6 1 4 ) 5 2 3 - 1 9 9 0 OREGON, Lake Oswego - I Squared, Inc. . . . . . . . . . . . . . . . . . . . . . . ( 5 0 3 ) 6 7 0 - 0 5 5 7 UTAH, Murray - Front Range Marketing . . . . . . . . . . . . . . . . . . . . ( 8 0 1 ) 2 8 8 - 2 5 0 0 VIRGINIA, Glen Burnie - Coherent Solution, Inc. . . . . . . . . . . . . . . . . ( 4 1 0 ) 7 6 1 - 2 2 5 5 WASHINGTON, Kirkland - I Squared, Inc. . . . . . . . . . . . . . . . . . . . . . . . . . . ( 4 2 5 ) 8 2 2 - 9 2 2 0 WISCONSIN, Pewaukee - Industrial Representatives . . . . . . . . . . . . . . . . ( 2 6 2 ) 5 74 - 9 3 9 3 International AUSTRALIA, North Ryde . . . . . . . . . . . . . . . . . . . . . . . T E L ( 6 1 ) 2 - 8 8 - 7 7 7 - 2 2 2 BELGIUM, Antwerpen . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 3 2 ) 3 - 2 4 8 - 4 3 - 0 0 BRAZIL, San Paulo . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 5 5 ) 1 1 - 5 5 0 1 - 2 1 0 5 CHINA, Beijing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 8 6 ) 1 0 - 6 5 1 0 - 2 1 8 8 Shanghai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 8 6 ) 2 1 - 6 3 5 - 0 0 8 3 8 Shenzhen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 8 6 ) 7 5 5 - 24 6 - 1 5 5 0 FINLAND, Helsinki . . . . . . . . . . . . . . . . . . . . . . T E L ( 3 5 8 ) 8 8 1 - 3 1 1 7 FRANCE, Paris . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 3 3 ) - 1 - 4 9 7 5 1 0 1 0 GERMANY, Bad Homburg . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 4 9 ) - 6 1 7 2 - 9 2 6 7 0 Munich . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 4 9 ) - 8 9 - 4 5 0 5 3 0 HONG KONG, Causeway Bay . . . . . . . . . . . . . . . . . . . T E L ( 8 5 ) 2 - 2 9 5 6 - 0 3 8 8 ITALY, Milan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 3 9 ) - 0 2 - 3 8 1 9 6 1 INDIA, New Delhi . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 9 1 ) 1 1 - 6 2 3 - 8 6 2 0 JAPAN, Osaka . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 8 1 ) 6 - 6 2 4 3 - 3 2 5 0 Tokyo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 8 1 ) 3 - 3 3 4 6 - 7 6 0 0 KOREA, Seoul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 8 2 ) 2 - 3 4 6 8 - 2 6 0 0 RUSSIA, Moscow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TEL(7)-095-795-06-22 SWEDEN, Stockholm . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 4 6 ) 8 - 5 62 - 5 4 0 - 0 0 TAIWAN,Taipei . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 8 8 6 ) 2 - 8 7 7 3 - 1 5 5 5 UNITED KINGDOM, Frimley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 4 4 ) 1 2 76 - 8 0 3 1 0 0 Haydock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T E L ( 4 4 ) 1 9 4 2 - 2 7 2 8 8 8 es Advanced Micro Devices reserves the right to make changes in its product without notice in order to improve design or performance characteristics.The performance characteristics listed in this document are guaranteed by specific tests, guard banding, design and other practices common to the industry. For specific testing details, contact your local AMD sales representative.The company assumes no responsibility for the use of any circuits described herein. © Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD Arrow logo and combination thereof, are trademarks of Advanced Micro Devices, Inc. Other product names are for informational purposes only and may be trademarks of their respective companies. Representatives in Latin America ARGENTINA, Capital Federal Argentina/WW Rep. . . . . . . . . . . . . . . . . . . .54-11)4373-0655 CHILE, Santiago - LatinRep/WWRep. . . . . . . . . . . . . . . . . . . . . . . . . .(+562)264-0993 COLUMBIA, Bogota - Dimser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 5 7 1 ) 4 1 0 - 4 1 8 2 MEXICO, Guadalajara - LatinRep/WW Rep. . . . . . . . . . . . . . . . . . . . ( 5 2 3 ) 8 1 7 - 3 9 0 0 Mexico City - LatinRep/WW Rep. . . . . . . . . . . . . . . . . . . . ( 5 2 5 ) 7 5 2 - 2 7 2 7 Monterrey - LatinRep/WW Rep. . . . . . . . . . . . . . . . . . . . . ( 5 2 8 ) 3 69 - 6 8 2 8 PUERTO RICO, Boqueron - Infitronics. . . . . . . . . . . . . . . . . . . . . . . . . . . . ( 7 8 7 ) 8 5 1 - 6 0 0 0 One AMD Place, P.O. Box 3453, Sunnyvale, CA 94088-3453 408-732-2400 TWX 910-339-9280 TELEX 34-6306 800-538-8450 http://www.amd.com ©2003 Advanced Micro Devices, Inc. 01/03 Printed in USA