ASR-SMD48D0.1P

Solid State Relay ASR-SMD DC Output • • • • • • • ASR Optoelectronic Isolation Load Voltage: 24VDC, 48VDC Load Current: 0.1A, 2A, 3A, 4A PCB Mounted Transistor or MOSFET Output Dielectric Strength 2500VACrms RoHS Compliant — SMD 48 D 3 N -K Packing - : Bulk pack A-Z SMD Series Load Voltage 24: 24VDC 48: 48VDC Control Voltage D:DC Control Load Current 0.1:0.1 Amps 2:2 Amps 3:3 Amps 4:4 Amps Control Voltage N: 5VDC P: 12VDC R: 24VDC S: 48VDC T: 60VDC None: No Socket K: With Socket Technical Specification INPUT CIRCUIT(TA=25˚C) Control Voltage Range N 4-6VDC P 9.6-14.4VDC R 19.2-28.8VDC S 38.4-57.6VDC T 48-72VDC Must Turn-on Voltage (1) N 4VDC P 9.6VDC R 19.2VDC S 38.4VDC T 48VDC Must Turn-off Voltage N 1VDC P 2.4VDC R 2.4VDC S 4.8VDC T 4.8VDC 1 Solid State Relay ASR-SMD DC Output Must Turn-off Voltage N 25mA (@6VDC)v P 25mA (@14.4VDC) R 25mA (@28.8VDC) S 23mA (@57.6VDC) T 23mA (@72VDC) Load Voltage Range 24 3-28VDC 48 3-58VDC Maximum Transient Overvoltage 24 33VDC 48 58VDC Load Current Range 0.1A 0.001 - 0.1A 2A 0.002 - 2A 3A 0.002 - 3A 4A 0.002 - 4A OUTPUT CIRCUIT(TA=25˚C) Maximum Turn-On Time 300μs Maximum Turn-Off Time 300μs Maximum Surge Current [@10 ms] 0.1A 1A 2A 20A 3A 30A 4A 48A Maximum Off-State Leakage Current [@ Rated Voltage] 0.1mA Maximum On-State Voltage Drop [@ Rated Current] 0.1A 1.5VDC Maximum On-State Resistance 2A/3A/4A 37mΩ 2 Solid State Relay ASR-SMD DC Output Dielectric Strength, Input/Output(50/60Hz) 2500Vrmsv Insulation Resistance 1000MΩ(@500VDC) Ambient Operating Temperature Range -30˚C +80˚C Ambient Storage Temperature Range -30˚C +100˚C Weight (Typical) ASR-SMD...-...Series 4g ASR-SMD...-…K Series 30g Installation SSR (1.10) (1.10) (0.20) (0.20) (0.02) (0.02) (0.07) (0.07) (0.64) (0.64) (0.20) (0.24) (0.04) (0.02) (0.15) (3.19) GENERAL INFORMATION (TA=25˚C) (1.36) (0.05) (0.20) (3.80) With Socket Wiring Diagram ASR-SMD…D...-NK Series ASR-SMD...D...-P/R/S/TK Series 3 Solid State Relay ASR-SMD DC Output Thermal Curve Attentions: 1. Soldering must be finished within 10 seconds at 260˚C,or finished within 5 seconds at 350˚C. Otherwise it may cause damage to the relay. 2. When connecting wiring to SSR please ensure screws are torqued down properly 4.43 in-lb, 0.5 N·m3. 3. When ambient temperature is above 25˚C or tight installation required, the maximum load current decreases. See thermal derating curve. 2. Terminal polarity must be observed. Otherwise it may cause damage to the relay. Product Certification 1741 Industrial Drive, No. 14 • Sterling, IL 61081 Tel: 815-632-3150 • Fax: 815-632-3449 www.altranmagnetics.com • sales@altranmagnetics.com 3