A27020A-55F

A27020A Series Preliminary Document Title 256K X 8 OTP CMOS EPROM Revision History Rev. No. 0.0 0.1 256K X 8 OTP CMOS EPROM History Initial issue Modify the program power supply Issue Date March 10, 2005 June 16, 2005 Remark Preliminary PRELIMINARY (June, 2005, Version 0.1) AMIC Technology, Corp. A27020A Series Preliminary Features 262,144 X 8 bit organization Programming voltage: 12.25V Access time: 55/70 ns (max.) Current: Operating: 30mA (max.) at 5MHz Standby: 100µA (max.) All inputs and outputs are directly TTL-compatible Available in 32-pin DIP and 32-pin PLCC packages 256K X 8 OTP CMOS EPROM General Description The A27020A chip is a high-performance 2,097,152 bit one-time programmable read only memory (OTP EPROM) organized as 256K by 8 bits. The A27020A requires only 5V power supply in normal read mode operation and any input signals are TTL levels. The A27020A is available in industry standard 32 pin dualin-line and 32 pin PLCC packages. Pin Configurations DIP PLCC A12 A15 A16 A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 GND 2 3 4 5 6 31 30 29 28 27 PGM A17 32 31 A14 A7 A13 A6 A8 A9 A11 OE A10 CE I/O7 I/O6 I/O5 GND I/O2 I/O3 I/O4 I/O1 I/O4 I/O3 I/O5 I/O6 A5 A4 A3 A2 A1 A0 I/O0 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 5 30 4 3 2 1 29 28 27 26 A14 A13 A8 A9 A11 OE A10 CE I/O7 7 8 9 10 11 12 13 14 15 16 26 25 24 23 22 21 20 19 18 17 A27020AL A17 25 24 23 22 21 VPP 1 32 VCC PRELIMINARY (June, 2005, Version 0.1) 1 AMIC Technology, Corp. PGM VCC VPP A27020A A27020A Series Pin Configurations Pin Name A0-A17 I/O7-I/O0 Function Address Inputs Data Inputs / Outputs Chip Enable Output Enable Program Strobe Program Power Supply Power Supply Ground CE OE PGM VPP VCC GND Operating Modes and Truth Table Mode Read Output Disable Standby Program Program Verify Program Inhibit Manufacturer Code(3) Device Code(3) Continuation Code(3) CE VIL VIL VIH VIL VIL VIH VIL VIL VIL OE VIL VIH X VIH VIL X VIL VIL VIL PGM X X X VIL Pulse VIH X VIH VIH VIH A0 X X X X X X VIL VIH VIL A1 X X X X X X VIL VIL VIH A9 X X X X X X VID VID VID VPP VCC VCC VCC 12.25V 12.25V 12.25V VCC VCC VCC VCC VCC VCC VCC 5.25V 5.25V 5.25V VCC VCC VCC I/O7-I/O0 Data Out Hi-Z Hi-Z Data In Data Out Hi-Z 37H 64H 7FH Notes: 1. X = Either VIH or VIL. 2. VID = 12V ± 0.5V. 3. A2 ~ A8 = A10 ~ A17 = VIL (For auto identification) PRELIMINARY (June, 2005, Version 0.1) 2 AMIC Technology, Corp. A27020A Series Functional Description Read Mode The A27020A has two control functions, both of which must be logically active in order to obtain data at the outputs. CE is the power control and should be used for device selection. OE is the output control and should be used to data to the output pins, which is independent of device selection. Assuming that addresses are stable, address access time (tAA) is equal to the delay from CE to output (tCE). Data is available at the output after a delay (tOE) from the falling edge of OE , as long as CE has been low and the addresses have been stable for at least tACC - tOE. Auto Identify Mode The auto identify mode allows the reading out of a binary code from a EPROM that will identify its manufacturer and type. This mode is intended for use by programming equipment for the purpose of automatically matching the device to be programmed with its corresponding programming algorithm. To activate the mode, the programming equipment must apply 12.0V ± 0.5V on address line A9 of the A27020A. Three identification code can be read from data output pin by toggling A0 and A1. The other addresses must be held at VIL during this mode. Byte 0 (with A0 at VIL, A1 at VIL) represents the manufacturer code which is 37H. Byte 1 and Byte 2 represent the device code and continuation code, which is 64H and 7FH respectively. All identifiers for these codes will possess odd parity, with MSB (IO7) defined the parity bit. Standby Mode The A27020A has a standby mode which reduces the active current from 30mA to 100µA. The A27020A is placed in the standby mode by applying a CMOS high signal to CE . When in the standby mode, the output are in a high impedance state, independent of the OE . Absolute Maximum Ratings* Ambient Operating Temperature (TA) . . ..-10°C to +85°C Storage Temperature Plastic Package (TSTG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . . . -55°C to 125°C Applied Input Voltage (VI): All Pins Except A9, VPP and VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to VCC + 0.6V A9, VPP . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to 12.5V VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to 7.0V Output Voltage (VO) . . . . . . . . . . . . -0.6V to 6.0V (Note 1) *Comments Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to this device. These are stress ratings only. Functional operation of this device at these or any other conditions above those indicated in the operational sections of this specification is not implied or intended. Exposure to the absolute maximum rating conditions for extended periods may affect device reliability. Notes: 1. During voltage transitions, the input may undershoot GND to -2.0V for periods less than 20 ns. Maximum DC voltage on input and I/O may overshoot to VCC + 2.0V for periods less than 20 ns. 2. When transitions, A9 and VPP may undershoot GND to -2.0V for periods less than 20 ns. Maximum DC input voltage on A9 and VPP is +12.5V which may overshoot to 12.7V for period less than 20 ns. PRELIMINARY (June, 2005, Version 0.1) 3 AMIC Technology, Corp. A27020A Series Read Mode DC Electrical Characteristics (Ta = 0°C to 70°C, VCC = 5V ± 10%, VPP = VCC) Symbol VOH VOL VIH VIL ILI Parameter Output High Voltage Output Low Voltage Input High Voltage Input Low Voltage Input Leakage Current 2.0 -0.5 -1 Min. 2.4 0.4 VCC + 0.5 0.8 +1 Max. Unit V V V V µA Conditions IOH = -400µA IOL = 2.1mA VCC = max. Vin = 0V to VCC VCC = max. Vout = 0V to VCC VCC = max. CE = VIL, OE = VIL Iout = 0mA, at 5MHz VCC = max. CE = VIH VCC = max. CE = VCC - 0.2V CE = OE = VIL, VPP = VCC A9 = VID, VCC = max. ILO Output Leakage Current -1 +1 µA ICC VCC Read Operating Current 30 mA ISB VCC Standby Current (TTL) 1 mA µA ISB1 VCC Standby Current (CMOS) 100 IPP IID VPP Current During Read A9 Auto Select Current 10 100 µA µA Capacitance (TA = 25°C, f = 1.0MHz) Symbol CIN COut Parameter Input Capacitance Output Capacitance Min. Max. 8 8 Unit pF pF Conditions VIN = 0V VOut = 0V * These parameters are sampled and not 100% tested. PRELIMINARY (June, 2005, Version 0.1) 4 AMIC Technology, Corp. A27020A Series Read Mode AC Characteristics (Ta = 0°C to 70°C, VCC = 5V ± 10%, VPP = VCC) Symbol Parameter Min. tCYC tAA tCE tOE tOH Cycle Time Address Access Time Chip Enable Access Time Output Enable Access Time Output Hold after Address, CE or OE , whichever Occurred First Output High Z Delay 0 55 55 55 30 0 55ns Max. Min. 70 70 70 35 70ns Max. ns ns ns ns ns Unit tHZ 20 20 ns Read Mode Switching Waveforms tCYC ADDRESS Address Valid CE tCE OE tOE tAA OUTPUT Valid Output tOH High-Z tHZ PRELIMINARY (June, 2005, Version 0.1) 5 AMIC Technology, Corp. A27020A Series AC Measurement Conditions for 55 ns Input Rise and Fall Times ≤ 10 ns Input Pulse Voltage: 0V to 3Volt Input and Output Timing Ref. Voltage: 1.5Volt 3.0V 1.5V 0V INPUT for 70 ns Input Rise and Fall Times ≤ 10 ns Input Pulse Voltage: 0.4V to 2.4Volt Input and Output Timing Ref. Voltage: 0.8V to 2.0Volt TEST POINTS 1.5V OUTPUT 2.4V 2.0V 0.8V 0.4V INPUT AC Testing Load Circuit TEST POINTS 2.0V 0.8V OUTPUT 1.3V 1N914 3.3KΩ DEVICE UNDER TEST OUT CL = 30pF or 100pF CL = 30pF for 55 ns CL = 100pF for 70/90 ns CL includes JIG capacitance PRELIMINARY (June, 2005, Version 0.1) 6 AMIC Technology, Corp. A27020A Series Programming and Program Verify The programming flowchart is shown in Page 10. The A27020A is shipped with all bits being set to "1". Programming causes relevant bits to be changed to "0". The programming mode is started by setting VCC to +5.25V and VPP to +12.25V, while CE and PGM are at VIL, and OE is at VIH. Data to be programmed can be directly input in the 8 bit format through the data bus. The write programming algorithm reduces programming time by using 100µs pulse followed by a byte verification to determine whether the byte has been successfully programmed. If the data does not pass the verification, an additional pulse programming is applied for a maximum of 25 pulses. On completion of 1 byte programming and, The verified address is incremented. After the final address is completed, all bytes are verified again with VCC = 5.0 Volt. Program Inhibit This mode is used to program one of multiple A27020A whose OE , PGM , VPP, VCC, address bus and data bus are connected in parallel. When programming is performed, other A27020A can be inhibited from being programmed by setting their CE pins to VIH. Programming Mode DC Characteristics (Ta = 0°C to 70°C, VCC = 5.25V ± 0.25V, VPP = 12.25V ± 0.25V) Symbol VOH VOL VIH VIL ILI ICC IPP VID VCC1 VPP1 Parameter Output High Voltage Output Low Voltage Input High Voltage Input Low Voltage Input Leakage Current VCC Current During Program VPP Current During Program A9 Auto Select Voltage Programming Supply Voltage Programming Voltage 11.5 5.0 12.0 2.0 -0.5 -1 Min. 2.4 0.4 VCC + 0.5 0.8 +1 50 50 12.5 5.5 12.5 Max. Unit V V V V µA Test Conditions IOH = -400µA IOL = 2.1mA VCC = max. Vin = 0V to VCC mA mA V V V CE = VIL A9 = VID Note: VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP. PRELIMINARY (June, 2005, Version 0.1) 7 AMIC Technology, Corp. A27020A Series Programming Mode AC Characteristics (Ta = 0°C to 70°C, VCC= 5.25V ± 0.25V, VPP = 12.25V ± 0.25V) Symbol tAS tDS tVPS tVCS tCES tPW tDH tOES tOE tOHZ tAH Parameter Address Valid to Program Low Input Valid to Program Low VPP High to Program Low VCC High to Program Low CE Low to Program Low Program Pulse Width Program High to Input transition Input Transition to OE Low OE Low to Output Valid OE High to Output Hi-Z OE High to Address Transition 0 Min. 2 2 2 2 2 95 2 2 100 130 105 Max. Unit µs µs µs µs µs µs µs µs ns ns ns PRELIMINARY (June, 2005, Version 0.1) 8 AMIC Technology, Corp. A27020A Series Programming and Verify Mode AC Waveforms PROGRAM VIH ADDRESS VIL tAS VALID PROGRAM VERIFY DATA tDS VPP1 VPP VCC tVPS VCC1 VCC VCC tVCS VIH CE VIL tCES VIH PGM DATA IN tDH DATA OUT tOE tOHZ tAH tPW VIL tOES VIH OE VIL PRELIMINARY (June, 2005, Version 0.1) 9 AMIC Technology, Corp. A27020A Series Programming Flowchart START ADDRESS=FIRST LOCATION INTERACTIVE SECTION VCC=5.25V VPP=12.25V X=0 PROGRAM ONE 100us PULSE INCREMENT X X = 25? YES NO FAIL FAIL VERIFY BYTE VERIFY BYTE PASS PASS INCREMENT ADDRESS NO LAST ADDRESS YES VCC=VPP=5.0V VERIFY SECTION VERIFY ALL BYTES ? PASS DEVICE PASSED FAIL DEVICE FAILED PRELIMINARY (June, 2005, Version 0.1) 10 AMIC Technology, Corp. A27020A Series Ordering Information Part No. A27020A-55 A27020A-55F A27020AL-55 A27020AL-55F A27020A-70 A27020A-70F A27020AL-70 A27020AL-70F Access Time (ns) 55 55 55 55 70 70 70 70 Operating Current Max. (mA) at 5MHz 30 30 30 30 30 30 30 30 Standby Current Max. (µA) 100 100 100 100 100 100 100 100 Package 32Pin DIP 32Pin Pb-Free DIP 32Pin PLCC 32Pin Pb-Free PLCC 32Pin DIP 32Pin Pb-Free DIP 32Pin PLCC 32Pin Pb-Free PLCC PRELIMINARY (June, 2005, Version 0.1) 11 AMIC Technology, Corp. A27020A Series Package Information P-DIP 32L Outline Dimensions unit: inches/mm D 32 17 E 1 16 E1 C A2 A A1 Base Plane Seating Plane B B1 e θ EA L Symbol A A1 A2 B B1 C D E E1 EA e L θ Dimensions in inches Min 0.015 0.149 1.645 0.537 0.590 0.630 0.120 0° Nom 0.154 0.018 0.050 0.010 1.650 0.542 0.600 0.650 0.100 0.130 Max 0.210 0.159 1.655 0.547 0.610 0.670 0.140 15 ° Dimensions in mm Min 0.381 3.785 41.783 13.64 14.986 16.002 3.048 0° Nom 3.912 0.457 1.270 0.254 41.91 13.767 15.240 16.510 2.540 3.302 Max 5.334 4.039 42.037 13.894 15.494 17.018 3.556 15 ° Notes: 1. The maximum value of dimension D includes end flash. 2. Dimension E does not include resin fins. PRELIMINARY (June, 2005, Version 0.1) 12 AMIC Technology, Corp. A27020A Series Package Information PLCC 32L Outline Dimension HD D 13 5 unit: inches/mm 14 4 1 32 20 30 21 29 A2 A HE E b1 GD y D θ A1 e b GE Dimensions in inches Dimensions in mm Min 0.47 2.67 0.66 0.41 0.20 13.89 11.35 1.12 12.45 9.91 14.86 12.32 1.91 0° Nom 2.80 0.71 0.46 0.254 13.97 11.43 1.27 12.95 10.41 14.99 12.45 2.29 Max 3.40 2.93 0.81 0.54 0.35 14.05 11.51 1.42 13.46 10.92 15.11 12.57 2.41 0.075 10° Symbol Min A A1 A2 b1 b C D E e GD GE HD HE L y θ 0.0185 0.105 0.026 0.016 0.008 0.547 0.447 0.044 0.490 0.390 0.585 0.485 0.075 0° Nom 0.110 0.028 0.018 0.010 0.550 0.450 0.050 0.510 0.410 0.590 0.490 0.090 Max 0.134 0.115 0.032 0.021 0.014 0.553 0.453 0.056 0.530 0.430 0.595 0.495 0.095 0.003 10° Notes: 1. Dimensions D and E do not include resin fins. 2. Dimensions GD & GE are for PC Board surface mount pad pitch design reference only. PRELIMINARY (June, 2005, Version 0.1) 13 AMIC Technology, Corp. L c