10-040557-000

Amphenol® Amphenol Amphenol ® ® AC and SAE AS50151 AMPHENOL CORPORATION Amphenol Industrial ACA-B and GT Series Threaded Standard Cylindrical Connectors AMPHENOL CORPORATION Amphenol Industrial Phone: 888-364-9011 191 Delaware Avenue Sidney, NY 13838-1395 www.amphenol-industrial.com Reverse Bayonet Coupling Connectors Phone: 888-364-9011 191 Delaware Avenue Sidney, NY 13838-1395 www.amphenol-industrial.com www.amphenol-industrial.com www.amphenol-industrial.com Amphenol® 97 Series Connectors are UL recognized and CSA recognized. Amphenol® 97 Series Connectors are UL recognized and CSA recognized. Termination Instructions: L-1295 SAE AS50151, AC, ACA and GT Series Solder and Crimp www.amphenol-industrial.com www.amphenol-industrial.com Amphenol SAE AS50151, AC, ACA and GT Series This publication contains instructions for installing, disassembling, inspecting and reassembling Amphenol, SAE AS5015, AC Threaded, ACA Reverse Bayonet and GT Reverse Bayonet Connectors manufactured by Amphenol Industrial Operations in it’s different Manufacturing Divisions. AC THREADED SERIES BASIC SHELL STYLES Plug: 06 A AD Inline: 01 AF Wall Mount: 01 E F Box Mount: 02 R 08:F NO REAR ACCESSORIES THREADS ON 02 BOX MOUNT RECEPTACLE www.amphenol-industrial.com Amphenol SAE AS50151, AC, ACA and GT Series This publication contains instructions for installing, disassembling, inspecting and reassembling Amphenol, SAE AS5015, AC Threaded, ACA Reverse Bayonet and GT Reverse Bayonet Connectors manufactured by Amphenol Industrial Operations in it’s different Manufacturing Divisions. SAE AS50151 SERIES BASIC SHELL STYLES Plug: 3106 A E/F Inline: 3101 08:A Wall Mount: 3100 08:E NO REAR ACCESSORIES THREADS ON 02 BOX MOUNT RECEPTACLE Box Mount: 3102 www.amphenol-industrial.com Amphenol SAE AS50151, AC, ACA and GT Series This publication contains instructions for installing, disassembling, inspecting and reassembling Amphenol, SAE AS5015, AC Threaded, ACA Reverse Bayonet and GT Reverse Bayonet Connectors manufactured by Amphenol Industrial Operations in it’s different Manufacturing Divisions. ACA-B SERIES BASIC SHELL STYLES Plug: 3106 E Inline: 3101 F 08:E Flange Rcpt: 3103/00 08:F NO REAR ACCESSORIES THREADS ON 02 BOX MOUNT RECEPTACLE Jamnut Rcpt: 3107 Box Mount: 3102 www.amphenol-industrial.com Amphenol SAE AS50151, AC, ACA and GT Series This publication contains instructions for installing, disassembling, inspecting and reassembling Amphenol, SAE AS5015, AC Threaded, ACA Reverse Bayonet and GT Reverse Bayonet Connectors manufactured by Amphenol Industrial Operations in it’s different Manufacturing Divisions. GT REVERSE BAYONET SERIES BASIC SHELL STYLES Plug: 3106 A Inline: 3101 AF F Flange Rcpt: 3103/00 R 08:F Jamnut Rcpt: 3107 08:R NO REAR ACCESSORIES THREADS ON 02 BOX MOUNT RECEPTACLE Box Mount: 3102 Amphenol www.amphenol-industrial.com Installation Instructions SAE AS50151, AC, ACA and GT Series, Containing Crimp Contacts. Amphenol, SAE AS50151, AC Threaded, ACA Reverse Bayonet and GT Reverse Bayonet incorporate MIL-STD-1651 insert arrangements as well as some special arrangements. Crimp type contacts in size 4/0,1/0,0,4,8,12,16 and 16S are available for use in these insert arrangements. This publication contains information for proper crimping, insertion and removal of crimp contacts as well as applicable tool information. 1. Cleaning: Inserts contacts and inside surfaces of shells must be kept free of oil, grease and dirt throughout the installation procedure. Use a clean cloth moistened with Isopropyl Alcohol. Do Not use Any Other Lubricant or Cleaning Chemical than Isopropyl Alcohol 2. Cable Wire and Preparation: a. Provide for sufficient wire slack to permit easy installation of the connector. Using Table 1 as a guide, cut the wires to length and strip the insulation the appropriate distance from the end. Use extreme care to avoid nicking or cutting wire strands. (Figure1 & 2) b. Check to be sure strands of wire are not separated. If necessary, reform by lightly twisting the strands together TABLE I Contact Size Strip Insulation 0 4 8 12 16 3/4” 1/2” 9/16” 5/16” 5/16” Figure 2 Figure 1 Amphenol www.amphenol-industrial.com Installation Instructions SAE AS50151, AC, ACA and GT Series, Containing Crimp Contacts (cont...). 3. Crimping: a. Insert the stripped end of wire into the contact wire-well and apply slight pressure until it is positively bottomed. Visually check to assure the wire strands are visible in the inspection hole provided in the wire well. (Figure 3) b. Using the appropriate crimping tool and preset the tool in accordance with instructions provided with the tool. Table IV. c. Special wire wells may require a reduction sleeve to obtain the appropriate tensile strength, insert the reduction sleeve into the wire well prior to inserting the wire. Table III lists the applicable wire well adapters for the various wire and contact combinations. d. Insert the contact and wire into the tool as far as possible, then close the tool handles. This took has a built in safety feature in that the handles cannot be reopened until the crimping cycle is completed, refer to Table II for tensile strength data. Visually inspect the crimp. Wires should be visible in the inspection hole (Figure 4) TABLE II Tensile Strength for Crimp Joint Tests Contact Size Wire Size Initial Min. Pull-out Force lb. (Prior to Conditioning) 16 20 18 16 20 40 50 12 14 12 70 110 8 8 185 4 4 450 0 0 800 Figure 3 TABLE III Wire Well Adapters Mating End Size Wire Barrel Size Allowable Wire Size Required Wire Adapter Sleeve 16 Short 16 16 18 20 22* 10-74696-6 16 Long 16 16 18 20 22* 10-74696-6 12 12 12 14 - 8 8 8 10* 10-74696-1 4 4 4 6* 10-74696-2 0 0 0 2* 10-74696-7 *When using wire adapter sleeve shown. Figure 4 Amphenol www.amphenol-industrial.com TABLE IV CRIMP CONTACTS PART NUMBER PIN SOCKET Mating Size** Wire Well SILVER GOLD SILVER GOLD 10-040553-000 10-597160-15D 10-597109-161 10-597109-16D 10-606014-040 10-597160-40D 10-597109-401 10-597109-40D 10-606014-291 10-597160-34D 10-597109-341 10-597109-34D 10-606014- 46 10-597160-46D 10-597109-461 10-597109-46D 20-24 10-040557-000 10-597160-16D 10-597109-171 10-597109-17D 16-18-20 10-606014-022 10-597160-22D 10-597109-221 10-597109-22D 12-14 10-606014-171 10-597160-17D 10-597109-141 10-597109-14D 10-606014-301 10-597160-32D 10-597109-321 10-597109-32D Insertion Tool Extraction Tool 11-7345 11-8250 11-7345 11-8250 11-7082 11-8250 11-8220 11-8250 11-7365-4*** Pin-11-73708-4 Socket-11-7674-2 11-7365-5*** Pin-11-7370-5 Socket-11-7674-3 * * Crimp Tool Positioner/ Die Set Locator/ Color 16-18-20 16S 16L 12-14 20-22 14-16 18-20 10-606014-311 10-597160-33D 10-597109-331 10-597109-33D 20-22 10-606014-361 10-597160-36D 10-597109-361 10-597109-36D 20-24 10-606014-121 10-597160-12D 10-597109-131 10-597109-13D 12-14 10-606014-231 10-597160-23D 10-597109-231 10-597109-23D 8-10 10-606014-251 10-597160-26D 10-597109-261 10-597109-26D 10-12 10-606014-271 10-597160-27D 10-597109-271 10-597109-27D 10-606014-261 10-597160-24D 10-597109-241 10-597109-24D 18-20 10-606014-201 10-597160-20D 10-597109-201 10-597109-20D 20-22 10-040792-000 10-597160- 8D 10-040793-000 10-597109- 8D 8 10-606014- 41 10-597160-41D 10-597109-411 10-597109-41D 10-606014-321 10-597160-28D 10-606014-321 10-597109-28D 10-606014-381 10-597160-38D 10-597109-381 10-597109-38D 12-14 10-040564-000 10-597160- 4D 10-040565-000 10-597109- 4D 4 10-606014- 58 10-597160-58D 10-597109-581 10-597109-58D 10-606014-331 10-597160-35D 10-597109-351 10-597109-35D 10-606014- 44 10-597160-44D 10-606015-441 10-597109-44D 10-581806-000 10-597160- 1D 10-581808-000 10-597159- 1D 10-606014-341 10-597160-29D 10-597109-291 10-597109-29D 10-606014-351 10-597160-30D 10-606015-351 10-597109-30D 10-597276-48 10-597276-48D 10-606015-48 10-597109-48D 12 8 4 14-16-18 6 10-12 6 8 Red Daniels AF8 or M225520/1-01 Daniels: TH29-1 Astro Tools 616266 Pin: Blue Socket: Green Green Pico 400 BHD or Daniels WA23 Pico 414DA-8N Daniels WA23-2 Pico: Pin- 4025 Socket-4026 Pico 414DA-4N Daniels WA23-4 Pico: 4043 Pico 414DA-0N Daniels WA23-5 Pico: Pin-4042-1 Socket-4042 Pico 514DA2/0N Pico Pin-6490 Pico 514DA4/0N Socket-6491 10 0 0 0-2 4 2/0 2/0 Pico 5000 10-597276-47 10-597276-47D 10-606015-47 10-597109-47D 4/0 4/0 * * Consult Amphenol Industrial, Daniels Manufacturing or Pico Tools. ** Letter Designations: S designates Short, L designates Long. *** 11-7365 Series Insertion Tool and 11-7370, 11-7674 Series Removal Tools must be used with 11-7364 Arbor press. Refer to L-632 for Applicable instructions. * Amphenol www.amphenol-industrial.com Installation Instructions SAE AS50151, AC, ACA and GT Series, Containing Crimp Contacts (cont...). 4. Installing Contacts a. Slide the connector rear accessories over the wire bundle in the correct sequence, Cable Clamp /End bell (may Include Tapered sleeve or other accessories depending on Cable clamp style, Adapter (if required), Sleeve, Grommet. (Figure 5) b. Use the Insertion tool specified in Table IV, Place the contact in the tool, the tool should but against the shoulder of the of the contact. Contact sizes 16S, 16 and 12 Use a pliers style tool. c. Contact size 8, 4 and 0 us a “C” style shaped shaft. d. Lubricate the grommet, insert the contact through the appropriate cavity position in the grommet, corresponding to the cavity position on the rear portion of the insert (Figure 6), size 16S, 16 and 12 Pilot pins may be used to assist in the installation of socket contacts. See Figure 7. Figure 5 10-242758-16 size 16 socket contact pilot pins 10-242758-12 size 12 socket contact pilot pins 10-242758-8 size 8 socket contact pilot pins To assist in contact insertion. Vibraslide 084 Pinlube may be applied to the pilot pins or pin contacts. Figure 6 Figure 7 www.amphenol-industrial.com Amphenol Installation Instructions SAE AS50151, AC, ACA and GT Series, Containing Crimp Contacts (cont...). 4. Installing Contacts e. Place the connector on mating shell or connector for greater stability, if you are not using a fixture make sure to allow clearance on the mating side of the connector to allow the guide pins to go through. f. Lubricate the rear face of the insert and cavities with Isopropyl Alcohol Only. g. Using guide pins as needed, with Firm even pressure push the contact straight down until the contact is seated in position, personnel inserting the contact will normally feel the contact reach it’s fully seated position, it is recommended to start a the center of an insert arrangement and work outwards toward the edge, if you are terminating a Plug connector make sure the coupling nut is assembled onto the plug shell before insert the contacts. (Figure 8) h. The Arbor Press can be used for inserting size 4 or larger contacts, when the Arbor Press method of insertion is used, contacts and attached wire should be placed in the predetermined insertion tip and inserted in their applicable insert cavity, positive stop setting of the Arbor Press will control the contact insertion depth. i. Visually check the mating ends of the connector to be sure all contacts are properly inserted to the same depth. j. Fill all the empty cavities with non terminated contacts and grommet with sealing plugs to maintain the sealing integrity of the connector. k. After the installation and inspection of contacts has been completed, slide all rear accessories forward and tighten with 11-6147-1 pliers. l. Torque specifications are listed in L-725-3. (Figure 9) m. Removing Contacts for Replacement, Loosen all rear accessories and unscrew them from the connector shell, slide all parts back along the wire, determine the appropriate removal tool (Table IV) and push back the contact through the mating side of the connector and remove. Figure 8 Amphenol www.amphenol-industrial.com Installation Instructions SAE AS50151, AC, ACA and GT Series, Containing Solder Contacts. 5. Preparation for installation: a. Slide the connector rear accessories over the wire bundle in the correct sequence, Cable Clamp / End bell (may Include Tapered sleeve or other accessories depending on Cable clamp style, Adapter (if required), Sleeve, Grommet. (Figure 5) b. Lubricate the grommet,, insert the wire through the appropriate cavity position in the grommet, corresponding to the cavity position on the rear portion of the insert. Use Isopropyl Alcohol to lubricate the grommet. Figure 5 Figure 6 6. Cable and Wire Preparation: a. Provide sufficient wire slack to permit easy installation. b. Strip the wire ends according to the size of contact see Table V. TABLE V Contact Size Strip Cable Insulation to “B” 0 4 8 12 16 3/4” 5/8” 5/8” 5/16” 1/4” Amphenol www.amphenol-industrial.com Installation Instructions SAE AS50151, AC, ACA and GT Series, Containing Solder Contacts (cont...). 7. Cable and Wire Preparation: a. Make Sure the stripped conductors are clean, straight and strands are tight together. b. Apply a good grade of Rosin Alcohol to the stripped ends, this can be done by dipping the bare ends in flux half way to the insulation, shake off excess flux. c. Pre-Tin approximately 50% of the exposed conductor end. This can be achieved using a solder pot or wire solder a good grade of 60/40 Tin-Lead solder is recommended. Solder pot temperature should be 500° to 550° F, avoid melting, burning or scorching the insulation. Shake off excess solder. d. Wire wells of size 12 and 16 contacts are Pre-Filled, larger sizes are Pre-Tinned. 8. Soldering: a. Either a Probe Type resistance soldering equipment or a soldering iron is suitable for soldering conductors to contacts. When using an Iron it may be necessary to re-shape the tip to provide access to dense contact arrangements. To obtain the greatest amount of heat transfer use the recommended iron size in Figure 10. b. Position the connector so the cut away sides of the wire well are facing up, add support to the wire being attached to relief strain from the connector shell and insert. c. It is recommended to start soldering at the bottom row working across then up. d. To avoid a cold joint maintain heat until solder both in the solder well and on the conductor is completely liquid. e. Careful not overheat the bonded in insert, do not hold the contact at elevated temperature any longer than necessary. f. While holding the wire steady and properly aligned remove the heat source and allow the solder to cool until completely solid, permitting the wire to move while the solder is in plastic state will result in crystallization and a weak joint. g. Remove any Excess solder from the wire well. h. After the conductors have all been soldered, proceed to slide back and assemble the rear accessories. i. To remove unsolder the conductors. Probe type Resistance Soldering Iron 500 WATT Size 0-4 300 WATT Size 3 100 WATT Size 12-16 Figure 10 Soldering Material FLUX SOLDER ROHS Compliant Solder Approved Source: Kester Solder Company Alpha Metals Inc. Qualitek International, Inc. Figure 11 9-6037 J-STD-004 Types ROL0 / ROL1 ROSIN High Grade 60/40 TIN-LEAD Tin-Silver & Tin-Copper Figure 12 Amphenol www.amphenol-industrial.com Torque Values - Electrical Connectors 1. Introduction: This publication contains minimum and maximum torque values recommended by Amphenol Corporation, Sidney, New York 13838. 5. Torques values are listed by thread sizes in Table I below and Tables II, III and IV on the next page. We recommend reviewing applicable connector catalogs for mating and accessory thread diameters for each connector shell size. Amphenol catalogs are available on-line at www.amphenol-aerospace.com or www. amphenol-industrial.com. 2. Maximum torque values are primarily governed by strength of material used to fabricate threaded components. Maximum values listed in this publication were computed to protect threads and other bearing surfaces which could be damaged by excessive torque. NOTE: See torque value notes (6, 7, 8) following Table I for accessories having three threads or less. 3. Minimum torque vales were computed to assure proper mating of connectors and/or accessories (when threaded areas are properly lubricated). Torque values are shown as follows: Table I for connectors with single start threads, Table III for connectors with double stub threads, Table IV for MIL-DTL-26482 bayonet coupling, and Table V for MIL-DTL-38999 Series I & III connectors. 6. The torque values listed in Table I are for UN (Handbook H-28) threads. These values apply to connector’s coupling nut, jam nut, cable clam, backshell or accessories. 7. Column “A” pf Table I lists the minimum and maximum values for threads on aluminum die cast parts such as MS or MS Modified connectors. 4. Metal to metal sealing of mated parts should occur where a flat gasket is used for an end seal. In some instances, when a cable accessory of MIL-C-85049/1, /2, /41 and /42 type clamp is used with maximum diameter cable, a metal to metal seating may not occur on the initial tightening. A second tightening is therefore necessary after cable has been allowed to cold flow (approximately 12 hours). 8. Column “B” of Table I lists the minimum ab maximum values for threads on extruded or machined aluminum and steel parts. The torque value for hex mounting nuts on all jam nut receptacles is listed in column “A” of Table I. The hex nuts are machined but the torque value is reduced due to the limited amount of threads. (Continues with NOTES on next page). Figure 9 TORQUE VALUES COLUMN “A” Torque for Threads on Die Cast Aluminum Parts Thread Size Inch Lbs. 0.3125 0.3750 0.4375 0.5000 0.5625 0.6250 0.6875 0.7500 0.8125 0.8750 0.9375 1.0000 1.0625 1.1250 1.1875 1.2500 1.3125 1.3750 1.4375 1.5000 1.6250 1.7500 1.8750 2.0000 2.0625 2.1250 2.2500 2.3125 2.3750 2.5000 2.5250 2.7500 2.8750 3.0000 Min. 20 20 20 20 26 26 30 34 40 46 50 55 60 70 75 80 85 90 100 100 110 120 140 150 160 170 170 180 190 200 210 220 230 240 COLUMN “B” Torque for Threads on Extruded or Machined Aluminum and Steel Parts Foot Lbs. Max. 26 26 26 26 32 32 36 40 46 50 55 60 65 75 80 85 90 95 110 110 120 130 150 160 170 180 180 190 200 210 220 230 240 250 Min. 8 8 9 10 11 12 13 14 14 15 16 17 18 18 19 20 Inch Lbs. Max. 9 9 10 11 12 13 14 15 15 16 17 18 19 19 20 21 Min. 70 70 70 70 80 90 100 110 120 140 150 160 190 210 240 260 280 300 300 325 350 375 400 425 450 475 500 525 550 575 600 650 700 750 Foot Lbs. Max. 75 75 75 75 85 95 110 120 130 150 160 170 200 230 260 280 300 320 325 350 375 400 425 450 475 500 525 550 575 600 650 700 750 800 Min. Max. 8 9 10 11 12 13 16 18 20 21 24 24 26 28 28 30 32 36 38 40 42 44 46 48 50 55 55 60 9 10 11 12 13 14 17 19 21 23 25 25 28 30 30 32 34 38 40 42 44 46 48 50 55 60 60 65 AMPHENOL CORPORATION Amphenol Industrial Phone: 607-563-5011 40-60 Delaware Avenue Sidney, NY 13838-1395 www.amphenol-industrial.com IB-8 Notice: Specifications are subject to change without notice. Contact your nearest Amphenol Corporation Sales Office for the latest specifications. All statements, information and data given herein are believed to be accurate and reliable but are presented without guarantee, warranty, or responsibility of any kind expressed or implied. Statements or suggestions concerning possible use of our products are made without representation or warranty that any such use is free of patent infringement and are not recommendations to infringe any patent. The user should not assume that all safety measures are indicated or that other measures may not be required. Specifications are typical and may not apply to all connectors. HKA 2016