47-20245

NOTES: REVISIONS THIRD ANGLE PROJ. REV 1. INITIAL TOOL SETTING RQUIREMENTS: WITH DIES FIRMLY AFFIXED IN TOOL ON THE DIE MOUNTING SURFACES, CLOSE THE TOOL FULLY (UNTIL THE RATCHET RELEASES) WITH 25-35 LBS,HAND FORCE THE DIES MUST BE 'BUTTED' (TOUCHING BOTH FRONT & REAR SURFACES). THE RATCHET ADJUSTER WHEEL SHOULD BE POSITIONED IN THE CENTER INDENT (+/- ONE INDENT POSITION) A B DESCRIPTION DATE RELEASE TO MFG. 47-20027, 47-20247 DIE-SETS SIZE UPDATED & LENGTH COLUMN ADDED IN TABLE 18-Dec-14 12/8/15 ECO APPR 2809 CL/BCG 50544 CL 2. DO NOT SCALE THIS DRAWING. LENGTH "L" # 0.20 3. REMOVE ALL BURRS, BREAK SHARP EDGES AND CORNERS 0.005 MAXIMUM, UNLESS OTHERWISE SPECIFIED. 4. UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS ARE AFTER PLATING. 5. PACKAGING: A. QUANTITY: B. PACKAGE MARKING: DIE SET PART NUMBER SINGLE PACK AMPHENOL RF 47-2XXXX (SEE TABLE) DATE CODE DIE SET OPENINGS IN INCHES (MM) (UNLESS OTHERWISE NOTED, ALL OPENINGS ARE HEXAGONAL) LENGTH "L" 47-20000 0.068(1.73) 0.213(5.41) 0.255(6.48) - - 34.00(1.340) 47-20008 0.151(3.83) 0.178(4.52) 0.213(5.41) - - 34.00(1.340) 47-20004 47-20003 47-20029 47-20001 47-20002 47-20245 47-20026 47-20025 47-20024 47-20027 47-20028 47-20030 47-20247 47-20249 47-20250 47-20251 47-20252 0.068(1.73) 0.080(2.03) 0.255(6.48) 0.052(1.32) 0.178(4.52) 0.190(4.82) 0.213(5.40) 0.068(1.73) 0.320(8.13) 0.068(1.73) 0.324(8.23) 0.429(10.90) 0.042(1.07) 0.068(1.73) 0.178(4.52) 0.105(2.67) 0.068(1.73) 0.042(1.07) 0.052(1.32) 0.052(1.32) 0.324(8.23) 47-20257 0.324(8.23) 0.118(3.00) - 47-20256 0.255(6.48) 0.068(1.73) 0.042 (1.07) SQ. 47-20255 0.068(1.73) 0.042(1.07) 0.042(1.07) 0.178(4.52) 0.052(1.32) 0.429(10.90) 0.105(2.67) - 0.429(10.90) 0.429(10.90) 0.042(1.07) 0.178(4.52) 0.100(2.54) 0.100(2.54) 47-20253 47-20254 0.128(3.25) 0.213(5.41) 0.178(4.52) 0.350(8.88) - - 0.213(5.40) - - 34.00(1.340) - 34.00(1.340) - - - 34.04(1.341) - 34.00(1.340) - - 0.255(6.48) 0.100(2.54) 0.429(10.90) 0.263(6.68) - - 0.278(7.08) - - 0.128(3.25) 0.178(4.52) - - - - - 0.068(1.73) 0.178(4.52) 0.278(7.06) 0.255(6.48) 0.319(8.10) 0.255(6.48) 0.042(1.07) - 0.075(1.90) - 0.128(3.25) 39.24(1.546) - 0.068(1.73) 0.151(3.83) 0.075(1.90) 34.00(1.340) 0.255(6.48) 0.128(3.25) 0.068(1.73) 34.00(1.340) 0.213(5.41) 0.068(1.73) 0.187(4.75) 34.00(1.340) 0.100(2.54) 0.052(1.32) 0.278(7.06) - - 0.255(6.48) 0.068(1.73) - 0.042(1.07) 0.255(6.48) 0.151(3.84) - - 0.324(8.23) - UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN METRIC AND TOLERANCES ARE: