47-20257

NOTES: REVISIONS THIRD ANGLE PROJ. 1. INITIAL TOOL SETTING RQUIREMENTS: WITH DIES FIRMLY AFFIXED IN TOOL ON THE DIE MOUNTING SURFACES, CLOSE THE TOOL FULLY (UNTIL THE RATCHET RELEASES) WITH 25-35 LBS,HAND FORCE THE DIES MUST BE 'BUTTED' (TOUCHING BOTH FRONT & REAR SURFACES). THE RATCHET ADJUSTER WHEEL SHOULD BE POSITIONED IN THE CENTER INDENT (+/- ONE INDENT POSITION) REV DESCRIPTION DATE ECO APPR A RELEASE TO MFG. 18-Dec-14 2809 CL/BCG 2. DO NOT SCALE THIS DRAWING. 3. REMOVE ALL BURRS, BREAK SHARP EDGES AND CORNERS 0.005 MAXIMUM, UNLESS OTHERWISE SPECIFIED. 4. UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS ARE AFTER PLATING. 5. PACKAGING: A. QUANTITY: B. PACKAGE MARKING: DIE SET PART NUMBER SINGLE PACK AMPHENOL RF 47-2XXXX (SEE TABLE) DATE CODE DIE SET OPENINGS IN INCHES (MM) (UNLESS OTHERWISE NOTED, ALL OPENINGS ARE HEXAGONAL) 47-20000 0.068(1.73) 0.213(5.41) 0.255(6.48) - - 47-20004 0.068(1.73) 0.128(3.25) 0.178(4.52) - - 47-20008 0.151(3.83) 0.178(4.52) 0.213(5.41) - - 47-20003 0.080(2.03) 0.100(2.54) 0.429(10.90) - - 47-20029 0.100(2.54) 0.429(10.90) 0.213(5.41) - - 47-20001 0.042(1.07) 0.068(1.73) 0.255(6.48) 0.324(8.23) - 47-20002 0.042(1.07) 0.068(1.73) 0.178(4.52) 0.213(5.40) - 47-20245 0.042(1.07) 0.068(1.73) 0.190(4.82) 0.213(5.40) - 47-20026 0.255(6.48) 0.320(8.13) 0.350(8.88) - - 47-20025 0.052(1.32) 0.068(1.73) 0.100(2.54) 0.213(5.41) 0.255(6.48) 47-20024 0.178(4.52) 0.324(8.23) 0.068(1.73) - - 47-20027 0.116(2.95) 0.429(10.90) - - - 47-20028 0.178(4.52) 0.255(6.48) 0.052(1.32) 0.068(1.73) - 47-20030 0.042(1.07) 0.068(1.73) 0.255(6.48) 0.278(7.08) - 47-20247 0.106(2.70) 0.114(2.90) 0.130(3.30) - - 47-20249 0.068(1.73) 0.100(2.54) 0.429(10.90) - - 47-20250 0.042(1.07) 0.068(1.73) 0.128(3.25) 0.178(4.52) - 47-20251 0.052(1.32) 0.263(6.68) - - - 47-20252 0.052(1.32) 0.278(7.06) - - - 47-20253 0.042 (1.07) SQ. 0.068(1.73) 0.178(4.52) 0.278(7.06) 0.255(6.48) 47-20254 0.178(4.52) 0.187(4.75) 0.042(1.07) - - - 0.324(8.23) 0.319(8.10) 0.255(6.48) 0.042(1.07) - 47-20255 0.052(1.32) 0.068(1.73) 0.255(6.48) 0.324(8.23) - 47-20256 0.429(10.90) 0.075(1.90) 0.075(1.90) - - 47-20257 0.105(2.67) 0.128(3.25) 0.151(3.84) - UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN METRIC AND TOLERANCES ARE: