82-4426-1001

Amphenol® Assembly Instructions-C11 Type N CRIMP-CRIMP TYPES outer ferrule Amphenol Number Connector Type contact body assembly Strip Dimensions, inches (mm) Cable RG-/U a b c Cavity for Contact Hex Crimp Data Cavity for Die Set for Outer Ferrule Tool 227-944‡ CTL Series Tool No. 82-332 N Plug 9, 214 .531(13.5) .234(6.0) .140(3.5) .100(2.5) .429(10.9) 227-1221-25 82-340 N Plug 8, 213 .531(13.5) .234(6.0) .141(3.6) .100(2.5) .429(10.9) 227-1221-25 CTL-3 CTL-3 82-340-1052 N Plug B9913, 9914 .539(13.7) .250(6.4) .158(4.0) .116(2.9) .429(10.9) 227-1221-63 CTL-11 82-340-1054 N Plug LMR 400 .539(13.7) .250(6.4) .157(4.0) .116(2.9) .429(10.9) 227-1221-63 CTL-11 82-4425 N Plug 9, 214, 225, 393 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3 82-4425-1003 N Plug 9, 214, 225, 393 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3 82-4426 N Plug 8, 213 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3 8, 213, 214 Eth.Cables .630(16.0) .303(7.7) .157(4.0) .100(2.5) .429(10.9) 227-1221-25 CTL-3 N Plug Ethernet Cables .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3 82-4426-1002 N Plug Ethernet Cables .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3 82-4427 N Plug 142, 400 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .213(5.4) 227-1221-57 CTL-3 82-4427-1006 N Plug 142, 142B, 400 .600(15.2) .275(7.0) .140(3.5) .100(2.5) .213(5.4) 227-1221-57 CTL-3 82-4440 N Angle Plug 214, 225, 393 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3 82-4440-1001 N Angle Plug 9, 214, 225, 393 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3 82-5370 N Plug 55, 142, 223 .600(15.2) .275(7.0) .140(3.5) .100(2.5) .213(5.4) 227-1221-57 CTL-3 82-5372 N Panel Jack 55, 141, 142 .600(15.2) .275(7.0) .140(3.5) .100(2.5) .213(5.4) 227-1221-57 CTL-3 82-5373 N Bulkh. Jack 55, 142, 223 .640(16.3) .315(8.0) .180(4.6) .100(2.5) .213(5.4) 227-1221-57 CTL-3 82-5374 N Angle Plug 55, 142, 223 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .213(5.4) 227-1221-57 CTL-3 82-5375 N Plug 58, 141 .531(13.5) .233(5.9) .140(3.5) .100(2.5) .213(5.4) 227-1221-57 CTL-3 82-5375-RFX N Plug 58, 141 .630(16.0) .303(7.7) .157(4.0) .100(2.5) .213(5.4) 227-1221-57 CTL-3 82-5378 N Bulkh. Jack 58, 141 .640(16.3) .273(6.8) .180(4.6) .100(2.5) .213(5.4) 227-1221-57 CTL-3 CTL-2 82-5933 N Bulkh. Jack 316 .502(12.7) .102(2.6) .062(1.6) Solder .178(4.5) 227-1221-09 82-5988-1000 N Angle Plug 214, 393 .827(21.0) .492(12.5) .157(4.0) Solder .429(10.9) 227-1221-6001 CTL-3 82-5988-1004 N Angle Plug 214, 393 .827(21.0) .492(12.5) .157(4.0) Solder .429(10.9) 227-1221-6001 CTL-3 82-5993 N Plug LMR 600 .844(21.4) .344(8.7) .250(6.4) .176(4.5) .612(15.5) 227-1221-6001 — 82-5994 N Bulkh. Jack LMR 600 .844(21.4) .344(8.7) .250(6.4) .176(4.5) .612(15.5) 227-1221-6001 — 82-5995 N Angle Plug LMR 600 1.062(27.0) .562(14.3) .312(7.9) Solder .612(15.5) 227-1221-6001 — 82-6010 N Plug LMR 240 .610(15.5) .200(5.1) .200(5.1) Press-Fit .255(6.5) 227-1221-59,-13 CTL-1.5,8 82-6106 N Plug LMR 240 .687(17.4) .312(7.9) .187(4.7) .100(2.5) .255(6.5) 227-1221-59 CTL-5 82-5988-1000 N Angle Plug LMR 240 .827(21.0) .492(12.5) .157(4.0) .100(2.5) .255(6.5) 227-1221-59 CTL-5 82-5988-1004 N Angle Plug LMR 240 .827(21.0) .492(12.5) .157(4.0) .100(2.5) .255(6.5) 227-1221-59 CTL-5 Step 1 aA bB STEP 1 C c Step 2 crimp here STEP 2 Step 3 Step 1 Strip cable jacket, braid, and dielectric to dimensions shown. All cuts are to be sharp and square. Important: Do not nick braid, dielectric, and center conductor. Tinning of center conductor is not necessary if contact is to be crimped. For solder method, tin center conductor avoiding excessive heat. Step 2 Slide outer ferrule onto cable as shown. Flare slightly end of cable braid as shown to facilitate insertion of inner ferrule. Important: Do not comb out braid. Place contact on cable center conductor so it butts against cable dielectric. Center conductor should be visible through inspection hole in contact. Crimp or solder contact in place as follows: Crimp Method: Use Die Set Cavity for contact indicated in table above.Solder Method: Soft solder contact to cable center conductor. Do not get any solder on outside surface of contact. Avoid excessive heat to prevent swelling of dielectric. STEP 3 crimp here Step 3 Install cable assembly into body assembly so inner ferrule portion slides under braid. Push cable assembly forward until contact snaps into place in insulator. Slide outer ferrule over braid and up against connector body. Crimp outer ferrule using Die Set Cavity specified in table above. Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com 283 Assembly 82-4426-11RFX N Plug 82-4426-1001 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Amphenol: 82-201 82-5770 82-4426-1001 82-3312