901-256-11

NOTES: 1. MATERIALS AND FINISHES: BODY & CONTACT - BeCu, GOLD PLATING BUSHING ,CLAMP NUT, LOCKWASHER, HEX NUT INSULATORS - PTFE, NATURAL GASKETS - SILICONE RUBBER, RED REV -- & BRAID CLAMP - BRASS, GOLD PLATING AA DESCRIPTION DATE ECO APPR 11/32 ACROSS FLAT WAS 11/16 ACROSS FLAT 15-Mar-19 10981 MRM RELEASE TO MFG. .328 2. ELECTRICAL: A. IMPEDANCE: 3. MECHANICAL: A. TEMPERATURE RANGE: 4. PACKAGING: A. QUANTITY: SINGLE PACK B. MARKING: BAG TO BE MARKED "AMPHENOL RF, 901-256-11 , AND DATE CODE" 5. REVISIONS THIRD ANGLE PROJ. 50 OHM -65 $ C TO +165 $ -- -- +0,10 7,14 0 -0.000 ] [0.281 +0.004 .203 BRAID & DIELECTRIC C -- +0,07 3,18 0 CABLE ASSEMBLY INSTRUCTIONS: A. CUT JACKET TO DIMENSION SHOWN. B. COMB OUT BRAID AND FOLD OUT. C. PULL BRAID WIRES FORWARD AND TAPER TOWARD CENTER CONDUCTOR.PLACE CLAMP NUT ASSEMBLY OVER BRAID AND PUSH BACK AGAINST CABLE JACKET. FOLD BACK BRAID WIRES, TRIM AS NECESSARY SO THAT WIRES DO NOT TOUCH SHOULDER OF GASKET. D. SCREW TRIM TOOL 901-G ONTO CLAMP NUT ASSEMBLY.TIGHTEN NUT LIGHTLY. DO NOT DAMAGE GASKET. USING RAZOR BLADE, REMOVE EXPOSED DIELECTRIC. CUT MUST BE SQUARE. DO NOT NICK CENTER CONDUCTOR. E. REMOVE DIELECTRIC TRIM TOOL AND CLEAN ALL SURFACES THOROUGHLY.ASSEMBLE BUSHING ASSEMBLY AND SOLDER CENTER CONTACT TO CABLE. F. THREAD CONNECTOR ASSEMBLY ONTO PREPARED CABLE ASSEMBLY TIGHTEN TO 20-25 IN.-LBS TORQUE. -0.000 ] [0.125 +0.003 RECOMMENDED CABLE STRIPPING DIMENSIONS SCALE 2.200 RECOMMENDED MOUNTING HOLE DIMENSIONS MIL-C-39012 INSPECTION 6. CUSTOMER NOTE: SOLDER CONTACT TO CABLE. 11,58 REF [0.456 ] 7. SHOWS CABLE ENTRY DIMENSIONS. 10,80 REF [0.425 ] 7 1,63 [0.064 ] 7 0,76 [0.030 ] 7 2,90 [0.114 ] INTERFACE PER MIL-STD 348 SMA SERIES 1/4-36UNS-2A THREAD 5/16 HEX NUT LOCKWASHER 11/32 ACROSS FLAT CONNECTOR ASSEMBLY CONTACT GASKET BUSHING ASSEMBLY NOTICE - These drawings, specifications, or other data (1) are, and remain the property of Amphenol corp. (2) must be returned upon request; and (3) are confidential and not to be disclosed to any person other than those to whom they are given by Amphenol Corp. the furnishing of these drawings, specifications, or other data by Amphenol Corp., or to any other person to anyone for any purpose is not to be regarded by implication or otherwise in any manner licensing, granting rights to permitting such holder or any other person to manufacture, use or sell any product, process or design, patented or otherwise, that may in any way be related to or disclosed by said drawings, specifications, or other data. 5/16 HEX NUT CUSTOMER OUTLINE DRAWING THIS CONNECTOR COVERED BY U.S PATENT 3,676,573 & 3,651,941 UNLESS OTHERWISE SPECIFIED, DIMENSIO NS ARE IN INCHES AND TOLERANCES ARE: 2 PLACE DECIMAL 3 PLACE DECIMAL ANGLES CLAMP NUT ASSEMBLY ALL OTHER SHEETS ARE FOR INTERNAL USE ONLY MATERIAL SEE NOTES REFERENCE NAVORD 2901150-21A DOR 308987-51 MIL-C-39012/59-4007 CONFIGURATION LEVEL: In Work FINISH DRAWN MICHAEL MISCHKE DATE 15-Mar-19 ENGINEER O. BARTHELMES DATE 11/18/13 APPROVED KEN CAPOZZI DATE 22-Mar-19 CAD FILE TITLE SMA CONNECTOR CLAMP TYPE JACK WITH CAPTIVE CONTACT FOR RG-174/U RG-188/U & RG-316/U CABLES SCALE: 6.5:1.0 DWG SIZE B SHEET 2 OF 2 REV AA Amphenol RF www.amphenolrf.com DRAWING NO. 901-256-11 ITEM NO. 901-256-11 PART NO. 901-256-11