A-1JB

NOTES: REVISIONS THIRD ANGLE PROJ. REV 1. ELECTRICAL: A A: B: C. D. IMPEDENCE: 50 ^ , NOMINAL FREQUENCY RANGE: 0-6GHz (VSWR 1.3 MAX.) OPERATING VOLTAGE: 60 VAC CONTACT RESISTANCE: CENTER CONTACT: INITIAL: 20 m ^ MAX. AFTER: 25 m ^ MAX. OUTER CONTACT: INITIAL: 10 m ^ MAX. AFTER: 15 m ^ MAX. E. DIELECTRIC WITHSTANDING VOLTAGE: 200 VAC F. INSULATION RESISTANCE: 500 MEGOHMS MIN. 3.1 0.15 [.122 .006 ] G SIGNAL PAD H J K 2. PHYSICAL: RELEASE TO MFG. 3/3/14 HP 49763 EW REMOVED DRAWING RELICS 23-May-14 49937 EW ADD PPAP NOTE 2/5/16 50957 EW REDRAWN IN PRO-E, FIXED DOC ERROR \RD-DM14090501T1 2 0.1 [.079 .004 ] 10-Sep-14 50053 SH 4 0.1 [.157 .004 ] SCALE 8.000 SIGNAL PAD 1.8 0.1 [.071 .004 ] TYP.(2) 2.2 0.05 [.087 .002 ] TYP.(2) 2 0.05 [.079 .002 ] 1.75 0.1 [.069 .004 ] 0.4 [ .016 ] 2.6 0.1 [.102 .004 ] SIGNAL PAD 12 0.3 [.472 .012 ] 5.5 0.1 [.216 .004 ] 1.25 0.1 [ .049 .004 ] 4 0.05 [.157 .002 ] 1.9 0.05 [.075 .002 ] 1.6 [ .063 ] 8 0.1 [.315 .004 ] 0.35 0.1 [.014 .004 ] UNREELING DIRECTION THIS GROUND PAD IS OPTIONAL 1 0.05 [.039 .002 ] TYP.(2) 44924 APPR 2.6 0.1 [.102 .004 ] 4. PACKAGING: A. TAPE AND REEL PACKAGING. B. QTY : 2500 PCS/REEL. C. LEAVE 20 EMPTY POCKETS IN THE BEGINNING AND END OF EACH REEL. 1 0.05 TYP.(2) [.039 .002 ] ECO 5/7/04 CENTER CONTACT WAS BRASS, FLATNESS REQUIREMENT, REMOVED MFG LOCATION STAMP, OPERATING VOLTAGE WAS 500 VRMS 3. MATERIALS AND FINISHES(PLATING THICKNESS IN MICRO-INCHES): HOUSING: HIGH TEMP. PLASTIC UL94V-0/WHITE CENTER CONTACT: COPPER ALLOY, AU 5 MIN. PLATED OVER NI GROUND CONTACT: COPPER ALLOY, AG 100 MIN. PLATED OVER NI GROUND DATE 3 0.15 [.118 .006 ] 0.6 0.1 [.024 .004 ] A. TEMPERATURE RANGE: -40 $ C TO +90 $ C B. AMC INTERFACE IS FULLY COMPATIBLE WITH "U.FL" SERIES PRODUCT. C. SUITABLE FOR SOLDER REFLOW PROCESS. DESCRIPTION SIGNAL PAD 1.05 0.05 [.041 .002 ] TYP.(2) SCALE 2.500 EMBOSSED CARRIER TAPE DIMENSIONS 0.6 0.1 [.024 .004 ] CONFIGURATION CONTROL: NO CHANGES PERMITTED TO DRAWING WITHOUT PPAP QUALIFIED CUSTOMER APPROVAL 4.1 REF [ .161 ] 0.08 RECOMMENDED PCB PATTERN CUSTOMER OUTLINE DRAWING ALL OTHER SHEETS ARE FOR INTERNAL USE ONLY UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN METRIC AND TOLERANCES ARE: