AIT1-24-28SS

ENVIRONMENTALLY-SEALED FOR CHALLENGING ENVIRONMENTS The MIL-DTL-5015 AIT/MS series is a cost-effective threaded circular connector for use in harsh environments. These Amphenol connectors are sealed to withstand moisture, condensation, vibration and flash-over. Over 286 contact layouts are available, in variations that allow for just power, just signal, or a mix of both contact types. Available in five mounting styles, nineteen shell sizes, and solder or crimp termination. • Formerly MIL-C-5015 APPLICATIONS FEATURES Military, industrial and commercial environments requiring extreme reliability, high-power handling and cost efficiency. • Power generators • Off-road vehicles • Industrial machinery • Engines • Earth-moving equipment • Telecommunications • Sensors • Ships • Motion control • Mobile equipment 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 Amphenol AIT/MS Series MIL-DTL-5015 AGENCY APPROVALS MIL-DTL-5015 (Formerly MIL-C-5015) BROAD TEMPERATURE RANGE These connectors will operate in temperatures ranging from -67°F to +257°F (-55°C to +125°C). ENVIRONMENTAL These connectors will perform in the full range of operating conditions as defined in MIL-DTL-5015 and are recommended for conditions where vibration, moisture, pressure and/or temperature are extreme. RESILIENT INSULATOR AND GROMMET A resilient neoprene insulator and rear-seal grommet provide a liquid-tight assembly. RUGGED SHELL The rugged aluminum alloy shell and hardware are light in weight yet highly resistant to damage and corrosion. Shells are available in five different styles and in 19 sizes. WIDE RANGE OF WIRE GAUGES AND CURRENT CARRYING CAPACITY Up to 150 amps for standard military contacts and up to 255 amps using Radsok® contacts. Wire gauges from 24 to size 0 AWG. WIDE VARIETY OF CONTACTS Machined contacts with silver or gold plating are available in sizes from 16 through 0. Solder, Crimp, PC, and thermocouple contacts are available. For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 25 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 TECHNICAL SPECIFICATIONS MATERIALS & FINISHES Shell Aluminum alloy Plating Olive drab chromate coating over cadmium plating to QQ-P-416; black alloy, conductive black alloy, electroless nickel, anodized or green zinc Contacts Brass or copper alloy Platings Silver plating to QQ-S-365 (solder contacts have tinned solder pot) Gold plating to MIL-G-45204 Insulator Resilient Neoprene®, Viton®*, low-smoke, zero-halogen (LSZH) ELECTRICAL DATA Operating Voltage/Test Voltage NOMINAL DISTANCE (IN.) MS SERVICE RATING AIRSPACE CREEPAGE OPERATING  VOLTAGE* AC VRMS DC V PRESSURE ALTITUDE† 50,000 FEET STANDARD SEA LEVEL CONDITIONS PRESSURE ALTITUDE† 70,000 FEET MINIMUM MINIMUM MINIMUM TEST TEST TEST FLASHOVER FLASHOVER FLASHOVER VOLTAGE VOLTAGE VOLTAGE VOLTAGE VOLTAGE VOLTAGE AC (RMS) AC (RMS) AC (RMS) AC (RMS) AC (RMS) AC (RMS) I 1/32 1/16 250 200 1,400 1,000 550 400 325 260 A 1/16 1/8 700 500 2,800 2,000 800 600 450 360 D 1/8 3/16 1,250 900 3,600 2,800 900 675 500 400 E 3/16 1/4 1,750 1,250 4,500 3,500 1,000 750 550 440 B 1/4 5/16 2,450 1,750 5,700 4,500 1,100 825 600 480 C 5/16 1 4,200 3,000 8,500 7,000 1,300 975 700 560 *E  ach insulator has a specific service rating. These should be used by the designer only as a guide. The Service Ratings for each layout are listed on a pages 72-93. † Not corrected for change in density resulting from variations in temperature MS connectors show no evidence of breakdown when the given test voltages are applied between the two closest contacts and between the shell and the contacts closest to the shell for a period of one minute, per MIL-STD-1344 Method 3001. Current Rating & Contact Resistance CONTACT TEST CURRENT SIZE (AMPS) POTENTIAL DROP (MILLIVOLTS) CONTACT RESISTANCE (MILLIOHM) MAX. 16 13 49 12 23 (50*) 42 3 8 46 (69*) 26 (20*) 1 (0.44*) 4 80 (80*) 23 (18*) 0.5 (0.23*) 0 150 (225*) 21 (27*) 0.2 (0.18*) 6 *Using non-military crimp Radsok contact Maximum total current to be carried per connector in wire bundles as specified in MIL-W-5088. Contact resistance when tested to MIL-C-39029 will not exceed voltage drops listed in above table. Viton® is a registered trademark of Dupont Dow Elastomers 26 For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com MECHANICAL Wire Range Sizes 24 to 0 AWG (a crimp contacts on pages 30-31) Insulation Resistance >5000 megohms at 77°F (25°C) per MIL-DTL-5015, 3.18 Wire Sealing Range INSULATION OUTSIDE DIAMETER LIMIT CONTACT SIZE WIRE SIZE (MIL-W-5086) IN. MM. IN. 16 16 thru 20 .064 1.63 .130 3.30 12 12 thru 14 .114 2.90 .170 4.32 8 8 thru 10 .164 4.17 .255 6.48 4 4 thru 6 .275 6.98 .370 9.40 0 0 thru 2 .415 10.54 .550 13.97 MIN. MAX. MM. The connector is designed for individual wire sealing. Sealing of an outer cable jacket on multiconductor cables must be accomplished with an appropriate endbell. Sealing is only guaranteed if wires according to MIL-W-5086 or within the listed ranges are used. Insulation Strip Lengths (a see page 30) Mating Life 100 cycles minimum, to MIL-DTL-5015, 3.16 Salt Spray MIL-STD-1344 Method 1001 condition B minimum (cadmium), 48 hour, olive drab chromate over cadmium, non-conductive black alloy, conductive black alloy, green zinc, black anodized, electroless nickel Heat +257˚F (+125˚C) for 60 hours, +185˚F (+85˚C) for 1,000 hours per MIL-DTL-5015, 4.6.14, minimum Chemical Resistance 20-hour full-immersion unmated in hydraulic fluid and lubricating oil per MIL-DTL-5015 minimum Vibration 10 to 2,000Hz (10g’s) 10 microseconds maximum discontinuity to MIL-STD-1344 Method 2005, condition II per MIL-DTL-5015 Shock 50g 11 millisecond duration, three major axes. 10 microseconds maximum discontinuity to MIL-DTL-5015 per MIL-STD-1344 method 2004, condition A, 3.13 Contact Type Solder, crimp, PC, or thermocouple (hard silver or gold plating) Number of Circuits 1 to 85 (a See pages 72-82) Contact Insertion Insertion from rear with simple hand tool. Removable, five cycles minimum. (Solder, PC and coax outer housings are bonded into the insulator.) Contact Retention 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 TECHNICAL SPECIFICATIONS To MIL-DTL-5015, 4.6.6 & 3.26 and separation forces CONTACT SIZE AXIAL LOAD NEWTONS LBS. SEPARATION FORCE MINIMUM NEWTONS LBS. 16 44 10 1 12 67 15 2 0.25 0.50 8 89 20 3 0.75 4 89 20 4 1.00 0 111 25 9 2.00 Polarization Integral key and keyway plus optional rotational polarization a See pages 83-93 or valid rotations. Approvals MIL-DTL-5015 For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 27 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 CREATE YOUR PART NUMBER USING THESE EIGHT STEPS STEP 1 2 3 4 5 AIT 6 A A 24-21 S SERIES PREFIX SHELL STYLE LAYOUT CONTACT ENDBELLS CABLE (If omtting CLAMP/BOOT endbell, enter -) (leave blank if not needed) 6 ROTATION 7 8 S -472 CONTACT TYPE PLATING (example) STEP 1: S E L E C T S H E L L ST Y L E, PL U G OR RECEP TACL E Mates with PLUGS 6 RECEPTACLES 0 6B Standard (MS3106) Wall Mount with Accessory Threads (MS3100) Box Mount 1 2 Cable Mount with Accessory Threads (MS3101) Box Mount No Accessory Threads (MS3102) STEP 2: SEL ECT END BEL L TIP: Order connector, backshell and all accessories as one part number! See www.peigenesis.com/en/solution-guides.html E MS Style (E/F) Standard Clamp RV No Clamp G Heat Shrink L Long Extender A Unsealed (no grommet seal) F T MS Style (MS3108) 90º R MS Style Low Profile Sealed (with grommet seal) P Potting *Potting Compound a See Page 443 G2 Spin Coupling Heat Shrink U Low Cost Shielded/Unshielded STEP 3: S E L E C T C A BL E CL A M P OR BOOT Heat Shrink Boot a See pages 440-441 28 A MS3057-A Standard Cable Clamp C (IF APPLICABLE) MS3057-C Gland Seal a See Page 41 9767 9767 Gland Seal for Smaller Cable Range a See Page 42 For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com STEP 5: SEL ECT CONTACT P = Pin S = Socket a See pages 72-82 STEP 6: S E L E C T R O TAT I ON STEP 7: S EL ECT CONTA CT TPYE a See pages 83-93 (Omit for normal) S = Solder H = PC** W, X, Y, Z C = Crimp* 0 = Less Contacts * When using a “C” in part number, the connector is supplied with the standard size crimp contacts for its layout. Bolded part numbers on a page 30 indicate crimp contact. Please contact us for connectors with reduced or enlarged crimp barrel contacts. **a See page 38 for post diameters and lengths. STEP 8: S EL ECT PL AT ING SHELL PLATING CONTACTS (Omit for olive drab chromate over cadmium) (MS style) (Omit for silver contacts) B30 = Gold 50µ Gold over Nickel T = Thermocouple (solder only) Need types with cavities and installed and uninstalled RDS = RADSOK (Crimp socket only) sizes 12,8,4,0 023 = 024 = 025 = Electroless Nickel 116 = Less pre-tinned solder cups G96 = Black Anodized 472 = 116&025 mod codes (RoHS) 548 = 116&023 mod codes (RoHS) 553 = 116&027 mod codes (RoHS) (RoHS with crimp or 116 contacts) EXTERNAL THREAD VERSION   Green Zinc Cobalt Black Alloy MATERIALS (Omit for standard neoprene) L = Low-smoke, zero-halogen V = High-temperature Viton® (RoHS with crimp or 116 contacts) 027 = Conductive Black Alloy STANDARD SPECIALS — INTERNAL THREAD VERSION (RoHS with crimp or 116 contacts) 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 STEP 4: S E L E C T L AY O U T CONTACT US WITH NPT THREAD SIZE, SEAL TITE CONDUIT DIAMETER, OR CABLE OUTSIDE DIAMETER. LOW COST GLAND SEAL CONDUIT PLASTIC CONDUIT METAL GLAND SEAL SHIELDED CABLE MESH GRIP a See pages 445 a NEED HELP? PEI engineers will help you solve your design challenges and build the perfect part for your application. Email us at sales@peigenesis.com or complete our online Technical Request at www.peigenesis.com/technical-support. To contact us by phone, please see the back cover for a complete listing of our branch offices and contact numbers. For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 29 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 PIN & SOCKET CRIMP CONTACTS PIN CONTACT • CONTACT SIZE WIRE SIZE AWG WIRE STRIP LENGTH SOCKET CONTACT • • • PART NUMBER PIN CONTACT WIRE STRIP LENGTHS INCHES (MM) SOCKET CONTACT GOLD SILVER SILVER GOLD 16S 16-18-20 AIC16S-16P* AIC16S-16PG* AIC16S-16S* AIC16S-16SG* 12-14 AIC16S-12P AIC16S-12PG AIC16S-12S AIC16S-12SG 16S† 14-16 AIC16S-14P AIC16S-14PG AIC16S-14S AIC16S-14SG C3 18-20 AIC16S-20P AIC16S-20PG AIC16S-20S AIC16S-20SG C13 20-22 AIC16S-22P AIC16S-22PG AIC16S-22S AIC16S-22SG C14 22-24 AIC16S-24P AIC16S-24PG AIC16S-24S AIC16S-24SG C2 16 16-18-20 AIC16-16P* AIC16-16PG* AIC16-16S* AIC16-16SG* 12-14 AIC16-12P AIC16-12PG AIC16-12S AIC16-12SG 14-16 AIC16-14P AIC16-14PG AIC16-14S AIC16-14SG C3 18-20 AIC16-18P AIC16-18PG AIC16-18S AIC16-18SG C13 20-22 C14 20-24 12 16 AIC16-20S AIC16-20SG AIC16-2024S AIC16-2024SG 22-24 AIC16-22P AIC16-22PG AIC16-22S AIC16-22SG 12-14 AIC12-12P* AIC12-12PG* AIC12-12S* AIC12-12SG* - AIC12-12SRAD C2 .312 (7.9) - 8-10 AIC12-8P AIC12-8PG AIC12-8S AIC12-8SG C5 12 10-12 AIC12-10P AIC12-10PG AIC12-10S AIC12-10SG C8 14-16 AIC12-14P AIC12-14PG AIC12-14S AIC12-14SG C9 16-18 AIC12-16P AIC12-16PG AIC12-16S AIC12-16SG C7 18-20 AIC12-18P AIC12-18PG AIC12-18S AIC12-18SG C6 20-22 AIC12-20P AIC12-20PG AIC12-20S AIC12-20SG C40 8 8 8 High-Power AIC8-8P* AIC8-8PG* - - - 10-12 AIC8-10P AIC8-10PG AIC8-10S AIC8-10SG C10 12-14 AIC8-12P AIC8-12PG AIC8-12S AIC8-12SG C38 4 4 AIC4-4P* AIC4-4PG* AIC4-4S* AIC4-4SG* 4 4 High-Power - - AIC4-4SRAD 8 AIC4-8P 0 0 AIC0-0P* AIC0-0PG* 0 0 High-Power AIC4-8PG - - 0.312 (7.9) .126-.177 (3.2-4.5) 0.563 (14.3) .150-.256 (3.8-6.5) 0.500 (12.7) .279-.366 (7.1-9.3) AIC8-8S* AIC8-8SG* AIC8-8SRAD .090-.118 (2.3-3.0) C36 8 0.312 (7.9) C4 AIC16-20P AIC16-20PG - WIRE SEALING RANGE INCHES (MM) C4 AIC16-2024P AIC16-2024PG 12 High-Power WIRE RANGE AIC4-8S - AIC4-8SG C15 AIC0-0S* AIC0-0SG* AIC0-0SRAD - 0-2 AIC0-2P AIC0-2PG AIC0-2S AIC0-2SG C11 4 AIC0-4P AIC0-4PG AIC0-4S AIC0-4SG C12 . 0.750 (19.0) .394-.539 (10.0-13.7) *Bolded items are standard crimp contacts. SOLDER THERMOCOUPLE CONTACTS 30 TYPE 16S Alumel PINS SOCKETS 10-040799-02P* 10-040799-02S* 16S† Chromel 10-040799-01P* 10-040799-01S* Iron 10-040799-03P* 10-040799-03S* Constantan 10-040799-04P* 10-040799-04S* 16 Alumel 10-040799-12P* 10-040799-12S* 16 Chromel 10-040799-11P* 10-040799-11S* Iron 10-040799-13P* 10-040799-13S* Constantan 10-040799-14P* 10-040799-14S* SOLDER THERMOCOUPLE CONTACTS TYPE PINS SOCKETS 12 12 Alumel 10-040799-42P* 10-040799-42S* Chromel 10-040799-41P* 10-040799-41S* Iron 10-040799-43P* 10-040799-43S* Constantan 10-040799-44P* 10-040799-44S* Thermocouple Types: J = Iron-Constantan K = Alumel-Chromel T = Copper-Constantan E = Chromel-Constantan *Contact us for availability. Contact information is below. † 16S contacts are used in 8S, 10S, 10SL, 12S, 14S & 16S connector sizes only. For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com TOOLS ACCESSORIES AF8 WA27F 400BHD Insert head first. Trim excess CONTACT SIZE Die set, locator and Go-No-Go gauge TH29-1 WIRE HOLE FILLER COLOR CRIMP TOOLS CRIMP LOCATOR &  DIE SETS 16S† LOCATOR COLOR PILOT PIN/INSERTION GUIDE FOR SOCKETS INSERTION TOOL 10-242758-016 DAK168-16 EXTRACTION TOOL Red Blue MS27488-16-3 16 Pin-Blue AF8-(hand) WA27F(pneumatic) Socket- TH29-1 Green 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 PIN & SOCKET CRIMP CONTACTS DRK59 †† Kit with Multiple Tips 12 8 4 0 Yellow MS27488-12-3 Red MS27488-8-3 Blue MS27488-4-3 Yellow MS27488-0-3 400BHD Green 10-242758-012 DAK168-12 Die Set 414DA-8N Locator 4025-Pin 4026-Socket - 10-242758-008 DAK282 Die Set 414DA-4N Locator 4043-2 - - AIC4INS AIC4EXT Die Set 414DA-0N Locator 4042 - - AIC0INS AIC0EXT †† Contact us for additional tool accessories. Contact information is below. All dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 31 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 PIN & SOCKET COAX CONTACTS PIN CONTACT SOCKET CONTACT WIRE STRIP LENGTH WIRE RANGE ACCESSORIES Insert head first. Trim excess. COAX CONTACT SIZE 12 8 4 COAX WIRE  SIZE PINS PART NUMBER SOCKETS SILVER GOLD SILVER GOLD RG161/U RG174A/U RG179B/U RG187A/U RG188A/U RG316/U 21-33034-1 21-33014-21 21-33048-1() 21-33130-1() 21-33033-1 21-33013-21 21-33047-1() 21-33129-1 () RG178B/U RG196A/U - 21-33014-22 - 21-33013-22 RG58C/U RG141A/U RG303/U 21-33034-2(1) 21-33014-1(5) 21-33016-5(3) 21-33130-2() 21-33033-2(1) 21-33048-2() 21-33013-1(5) 21-33047-2() 21-33015-5(3) 21-33129-2() RG59B/U RG62A/U RG62B/U RG210/U 21-33034-5(1) 21-33014-5(5) 21-33016-2(3) 21-33130-5() 21-33064-21() 21-33033-3(1) 21-33013-5(5) 21-33015-2(3) 21-33129-3() 21-33063-21() RG161/U RG174A/U RG179B/U RG187A/U RG188A/U RG316/U 21-33034-3(1) 21-33014-3(5) 21-33016-1(3) 21-33130-3 () 21-33064-20() 21-33033-3(1) 21-33013-3(5) 21-33015-1(3) 21-33129-3() 21-33063-20() RG180B/U RG195A/U 21-33034-6 21-33014-6(5) 21-33048-3() 21-33130-6() 21-33033-6 21-33013-(6) 21-33047-3() 21-33129-6() RG140/U RG302/U 21-33034-8 21-33014-8(5) 21-33033-8 21-33130-8() - 21-33013-8(5) 21-33129-8() RG55B/U RG142A/U RG142B/U RG223/U 21-33034-4 21-33014-5(5) 21-33130-4() 21-33033-4 21-33013-5(5) 21-33129-4()  RG59B/U RG62A/U RG62B/U RG210/U - 21-33060-10() - 21-33059-10() RG212/U - 21-33060-11() - 21-33059-11() - 31-33060-12() - 21-33059-12() RG55B/U RG142A/U RG142B/U RG223/U WIRE STRIP LENGTHS INCHES (mm) WIRE SEALING RANGE WIRE HOLE INCHES (mm) MIN. MAX. FILLER Contact us for details. 0.126 (3.2 mm) 0.177 (4.5 mm) Contact us for details. 0.150 (3.8 mm) 0.256 White (6.5 mm) 10-405996-8 Contact us for details. 0.279 (7.1 mm) 0.366 (9.3 mm) Yellow 10-405996-12 Blue 10-405996-4 ( ) Various platings available. Availability of coax contacts varies widely. Contact us for details. Contact information is below. All dimensions in inches (millimeters in parenthesis) 32 For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com TOOLS Crimp Dies COAX CONTACT SIZE COAX  WIRE SIZE HAND CRIMP TOOL CRIMP DIES USE LOCATOR COAX CLAMP NUT WRENCH RG161/U RG174A/U RG179B/U A RG187A/U M22520/10-01 RG188A/U 11-8676-1 M22520/10-05 RG316/U 12 RG178B/U B RG196A/U RG58C/U M22520/10-01 B RG141A/U M22520/10-07 11-8676-2 RG303/U 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 PIN & SOCKET COAX CONTACTS RG59B/U RG62A/U B M22520/5-01 M22520/5-45 11-8676-3 RG62B/U RG210/U RG161/U RG174A/U RG179B/U M22520/10-05 A RG187A/U RG188A/U 8 RG316/U RG180B/U B RG195A/U 11-8676-2 M22520/10-01 RG140/U RG302/U M22520/10-07 A RG55B/U RG142A/U RG142B/U RG223/U  RG59B/U RG62A/U RG62B/U RG210/U 4 RG212/U RG55B/U RG142A/U RG142B/U RG223/U M22520/5-01 M22520/5-45 B M22520/5-01 M22520/5-01 M22520/5-39 M22520/5-34 A A M22520/10-01 M22520/10-07 A B - 11-8676-4 A - All dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 33 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 DIMENSIONS RECEPTACLE STYLES AIT0-MS3100 AIT1-MS3101 AIT2-MS3102 AIT1-MS3101 AIT0-MS3100 AIT2-MS3102 AIT2-MS3102 AIT0/AIT1 AIT1 SHELL A THREAD SIZE CLASS 2A AIT0-MS3100/AIT2-MS3102 M +.010 R S -.000 P REF. +/-.005 +/-.031 T DIA. +.004 -.002 L REF KK DIA. LENGTH +.010 -.000 LENGTH 3100 3101 Q DIA. 8S .5000-28UNEF 10S .6250-24NEF 10SL .6250-24NEF 12S .7500-20UNEF 12 .7500-20UNEF 14S .8750-20UNEF 14 .8750-20UNEF 16S 1.0000-20UNEF 16 1.0000-20UNEF 18 1.1250-18NEF 20 1.2500-18NEF 22 1.3750-18NEF 24 1.5000-18NEF 28 1.7500-18NS 32 2.0000-18NS 36 2.2500-16UN 40 2.5000-16UN 0.562 (14.3) 0.562 (14.3) 0.562 (14.3) 0.562 (14.3) 0.750 (19.1) 0.562 (14.3) 0.750 (19.1) 0.562 (14.3) 0.750 (19.1) 0.750 (19.1) 0.750 (19.1) 0.750 (19.1) 0.812 (20.6) 0.812 (20.6) 0.875 (22.2) 0.875 (22.2) 0.875 (22.2) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.120 (3.0) 0.147 (3.7) 0.147 (3.7) 0.173 (4.4) 0.173 (4.4) 0.173 (4.4) 0.969 (24.6) 0.969 (24.6) 0.969 (24.6) 0.969 (24.6) 1.344 (34.1) 0.969 (24.6) 1.344 (34.1) 0.969 (24.6) 1.344 (34.1) 1.344 (34.1) 1.344 (34.1) 1.344 (34.1) 1.406 (35.7) 1.406 (35.7) 1.469 (37.3) 1.469 (37.3) 1.469 (37.3) 1.087 (27.6) 1.087 (27.6) 1.087 (27.6) 1.087 (27.6) 1.334 (33.9) 1.087 (27.6) 1.334 (33.9) 1.087 (27.6) 1.334 (33.9) 1.334 (33.9) 1.334 (33.9) 1.334 (33.9) 1.406 (35.7) 1.406 (35.7) 1.469 (37.3) 1.469 (37.3) 1.469 (37.3) 0.110 (2.8) 0.110 (2.8) 0.110 (2.8) 0.110 (2.8) 0.110 (2.8) 0.110 (2.8) 0.110 (2.8) 0.110 (2.8) 0.110 (2.8) 0.141 (3.6) 0.141 (3.6) 0.141 (3.6) 0.141 (3.6) 0.141 (3.6) 0.156 (4.0) 0.156 (4.0) 0.156 (4.0) 0.594 (15.1) 0.719 (18.3) 0.719 (18.3) 0.812 (20.6) 0.812 (20.6) 0.906 (23.0) 0.906 (23.0) 0.969 (24.6) 0.969 (24.6) 1.062 (27.0) 1.156 (29.4) 1.250 (31.8) 1.375 (34.9) 1.562 (39.7) 1.750 (44.5) 1.938 (49.2) 2.188 (55.6) 0.875 (22.2) 1.000 (25.4) 1.000 (25.4) 1.094 (27.8) 1.094 (27.8) 1.188 (30.2) 1.188 (30.2) 1.281 (32.5) 1.281 (32.5) 1.375 (34.9) 1.500 (38.1) 1.625 (41.3) 1.750 (44.5) 2.000 (50.8) 2.250 (57.2) 2.500 (63.5) 2.750 (69.9) 0.375 (9.5) 0.500 (12.7) 0.625 (15.9) 0.625 (15.9) 0.625 (15.9) 0.750 (19.1) 0.750 (19.1) 0.875 (22.2) 0.875 (22.2) 1.000 (25.4) 1.125 (28.6) 1.250 (31.8) 1.375 (34.9) 1.625 (41.3) 1.875 (47.6) 2.062 (52.4) 2.312 (58.7) 0.532 (13.5) 0.628 (16.0) 0.755 (19.2) 0.755 (19.2) 0.755 (19.2) 0.882 (22.4) 0.882 (22.4) 1.010 (25.7) 1.010 (25.7) 1.137 (28.9) 1.264 (32.1) 1.392 (35.4) 1.519 (38.6) 1.774 (45.1) 1.996 (50.7) 2.251 (57.2) 2.506 (63.7) AIT0/AIT1 B THREAD CLASS 2A .5000-28UNEF .5000-28UNEF .6250-24UNEF .6250-24UNEF .6250-24UNEF .7500-20UNEF .7500-20UNEF .8750-20UNEF .8750-20UNEF 1.0000-20UNEF 1.1250-18UNEF 1.2500-18UNEF 1.3750-18UNEF 1.6250-18UNEF 1.8750-16UN 2.0625-16UN 2.3125-16UN All dimensions in inches (millimeters in parenthesis) 34 For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 DIMENSIONS ENDBELL STYLES A L G XX H E (MS-E/F) L3 R  (MS-R) L4 AIT0-MS3100/AIT1-MS3101 SHELL SIZE 8S 10S 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 A & L ENDBELL L1 L2 MAX. B THREAD CLASS 2A 1.390 3.20 .5000-28UNEF (35.3) (81.20) 1.468 3.20 .5000-28UNEF (37.3) (81.20) 1.468 3.23 .6250-24NEF (37.3) (93.6) 1.468 3.58 .6250-24NEF (37.3) - 1.843 3.66 .6250-24NEF (46.8) - 1.468 3.23 .7500-20UNEF (37.3) (82.09) 1.843 3.64 .7500-20UNEF (46.8) - 1.468 3.23 .8750-20UNEF (37.3) (82.09) 1.843 3.58 .8750-20UNEF (46.8) (91.03) 1.938 3.66 1.000-20UNEF (49.2) (92.94) 1.844 3.64 1.1875-18NEF (46.8) (92.56) 1.938 3.65 1.1875-18NEF (49.2) (92.68) 1.969 3.73 1.4375-18NEF (50.0) (94.64) 2.188 3.90 1.4375-18NEF (55.6) (98.96) 2.157 4.10 1.7500-18NS (54.8) (104.24) 2.219 4.15 2.0000-18NS (56.4) (105.38) 2.188 4.15 2.2500-16UN (55.6) (105.38) AIT0/AIT1 G E ENDBELL R ENDBELL L L - - - - 2.129 (54.1) 2.129 (54.1) 2.129 (54.1) 2.201 (55.9) 2.524 (62.1) 2.201 (55.9) 2.524 (62.1) 2.596 (65.9) 2.654 (67.4) 2.654 (67.4) 2.885 (73.3) 2.885 (73.3) 2.943 (74.8) 2.943 (74.8) 3.068 (77.9) XX CABLE MIN. 1.588 (40.3) 1.588 (40.3) 0.281 1.588 (7.1) (40.3) 0.281 1.588 (7.1) (40.3) 0.281 1.931 (7.1) (49.0) 0.406 1.588 (10.3) (40.3) 0.406 1.931 (10.3) (49.0) 0.500 1.588 (12.7) (40.3) 0.500 1.931 (12.7) (49.0) 0.531 1.931 (13.5) (49.0) 0.656 1.931 (16.7) (49.0) 0.740 1.931 (18.8) (49.0) 0.781 2.009 (19.8) (51.0) 0.922 2.009 (23.4) (51.0) 1.156 2.072 (29.4) (52.6) 1.250 2.072 (31.8) (52.6) 1.562 2.072 (39.7) (52.6) H DIA MAX. 0.959 (24.4) 1.026 (26.1) 1.120 (28.4) 1.120 (28.4) 1.120 (28.4) 1.307 (33.2) 1.307 (33.2) 1.432 (36.4) 1.432 (36.4) 1.557 (39.5) 1.744 (44.3) 1.869 (47.5) 1.994 (50.6) 2.166 (55.0) 2.541 (64.5) 2.729 (69.3) 2.979 (75.7) L MAX. J ± .008 (±0.2) K ± .020 (+0.5) Z MIN. BB MAX. JJ +.008 (+.02) - - - - - - - - - - - - - - - - - - - - 1.969 0.138 0.461 0.303 0.524 0.610 (50.0) (3.5) (11.7) (7.7) (13.3) (15.5) - - - - - - - - - - - - - - - - - - - - 1.969 0.138 0.461 0.417 0.669 0.752 (50.0) (3.5) (11.7) (10.6) (17.0) (19.1) - - - - - - - - - - 1.969 0.138 0.461 0.531 0.862 0.941 (50.0) (3.5) (11.7) (13.5) (21.9) (23.9) 2.362 0.138 0.453 0.531 0.862 0.941 (60.0) (3.5) (11.5) (13.5) (21.9) (23.9) 2.362 0.138 0.453 0.575 0.862 0.941 (60.0) (3.5) (11.5) (14.5) (21.9) (23.9) 2.559 0.138 0.500 0.736 1.031 1.165 (65.0) (3.5) (12.7) (18.7) (26.2) (29.6) 2.559 0.138 0.500 0.819 1.031 1.165 (65.0) (3.5) (12.7) (20.8) (26.2) (29.6) 2.559 0.138 0.500 0.969 1.358 1.488 (65.0) (3.5) (12.7) (24.6) (34.5) (37.8) 2.559 0.138 0.500 1.063 1.358 1.488 (65.0) (3.5) (12.7) (27.0) (34.5) (37.8) 2.756 0.138 0.598 1.311 1.717 1.882 (70.0) (3.5) (15.2) (33.3) (43.6) (47.8) 3.150 0.138 0.598 1.516 1.717 1.882 (80.0) (3.5) (15.2) (38.5) (43.6) (47.8) 3.150 0.138 0.610 1.898 2.070 2.276 (80.0) (3.5) (15.5) (48.2) (52.6) (57.8) All dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 35 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 DIMENSIONS STYLE 6 PLUGS (BARREL ASSEMBLY) STYLE 6 ENDBELLS L A AIT6-MS3106 MS3108 E MS3106E MS3106F A & L SHELL A THREAD SIZE CLASS 2B Q1 DIA. MAX. BARREL B THREAD CLASS 2A 8S .5000-28UNEF 10S .6250-24NEF 10SL .6250-24NEF 12S .7500-20UNEF 12 .7500-20UNEF 14S .8750-20UNEF 14 .8750-20UNEF 16S 1.0000-20UNEF 16 1.0000-20UNEF 18 1.1250-18NEF 20 1.2500-18NEF 22 1.3750-18NEF 24 1.5000-18NEF 28 1.7500-18NS 32 2.0000-18NS 36 2.2500-16UN 40 2.5000-16UN 0.741 .5000-28UNEF (18.8) 0.869 .5000-28UNEF (22.1) 0.946 .6250-24UNEF (24.0) 0.995 .6250-24UNEF (25.3) 0.995 .6250-24UNEF (25.3) 1.123 .7500-20UNEF (28.5) 1.123 .7500-20UNEF (28.5) 1.250 .8750-20UNEF (31.8) 1.250 .8750-20UNEF (31.8) 1.333 1.0000-20UNEF (33.9) 1.461 1.1250-18UNEF (37.1) 1.588 1.2500-18UNEF (40.3) 1.715 1.3750-18UNEF (43.6) 1.968 1.6250-18UNEF (50.0) 2.209 1.8750-16UN (56.1) 2.463 2.0625-16UN (62.6) 2.719 2.3125-16UN (69.1) L1 L2 1.390 (35.3) 1.468 (37.3) 1.468 (37.3) 1.468 (37.3) 1.843 (46.8) 1.468 (37.3) 1.843 (46.8) 1.468 (37.3) 1.843 (46.8) 1.938 (49.2) 1.844 (46.8) 1.938 (49.2) 1.970 (50.0) 2.189 (55.6) 2.158 (54.8) 2.219 (56.4) 2.188 (55.6) MS3106E/MS3106F B THREAD CLASS 2A - .5000-28UNEF - .5000-28UNEF - 3.684 .6250-24NEF (93.6) - .6250-24NEF - - .6250-24NEF - 3.748 .7500-20UNEF (95.2) - .7500-20UNEF - 3.748 .8750-20UNEF (95.2) 3.710 .8750-20UNEF (94.2) 4.094 1.0000-20UNEF (104.0) 4.094 1.1875-18NEF (104.0) 4.102 1.1875-18NEF (104.2) 3.950 1.4375-18NEF (100.4) 4.392 1.4375-18NEF (111.6) 5.038 1.7500-18NS (128.0) 4.354 2.0000-18NS (100.6) 4.354 2.2500-16UN (110.6) L MAX. --- --- --- --- 2.129 (54.1) 2.129 (54.1) 2.129 (54.1) 2.201 (55.9) 2.524 (64.1) 2.201 (55.9) 2.524 (64.1) 2.596 (65.9) 2.654 (67.4) 2.654 (67.4) 2.885 (73.3) 2.885 (73.3) 2.943 (74.8) 2.943 (74.8) 3.068 (77.9) CABLE MIN. XX --------0.281 (7.1) 0.281 (7.1) 0.281 (7.1) 0.406 (10.3) 0.406 (10.3) 0.500 (12.7) 0.500 MSEeb (12.7) 0.531 (13.5) 0.656 (16.7) 0.740 (18.8) 0.781 (19.8) 0.922 (23.4) 1.156 (29.4) 1.250 (31.8) 1.562 (39.7) All dimensions in inches (millimeters in parenthesis) 36 For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com STYLE 6 RIGHT ANGLE ENDBELLS H T MS3108A MS3108E R  MS3106R L G MSRebSIDE R SHELL SIZE L MAX. 8S 10S 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 1.588 (40.3) 1.588 (40.3) 1.588 (40.3) 1.588 (40.3) 1.931 (49.0) 1.588 (40.3) 1.931 (49.0) 1.588 (40.3) 1.931 (49.0) 1.931 (49.0) 1.931 (49.0) 1.931 (49.0) 2.009 (51.0) 2.009 (51.0) 2.072 (52.6) 2.072 (52.6) 2.072 (52.6) H DIA. MAX. G J ± .008 K +.020 Z BB JJ +.008 L MAX. (±0.2) (+0.5) MIN. MAX. (+0.2) L MAX. 0.959 (24.4) 1.026 (26.1) 1.120 (28.4) 1.120 (28.4) 1.120 (28.4) 1.307 (33.2) 1.307 (33.2) 1.432 (36.4) 1.432 (36.4) 1.557 (39.5) 1.744 (44.3) 1.869 (47.5) 1.994 (50.6) 2.166 (55.0) 2.541 (64.5) 2.729 (69.3) 2.979 (75.7) - - - - - - - - - - - - - - - - - - - - 1.969 0.138 0.461 0.303 0.524 0.610 (50.0) (3.5) (11.7) (7.7) (13.3) (15.5) - - - - - - - - - - - - - - - - - - - - 1.969 0.138 0.461 0.417 0.669 0.752 (50.0) (3.5) (11.7) (10.6) (17.0) (19.1) - - - - - - - - - - 1.969 0.138 0.461 0.531 0.862 0.941 (50.0) (3.5) (11.7) (13.5) (21.9) (23.9) 2.362 0.138 0.453 0.531 0.862 0.941 (60.0) (3.5) (11.5) (13.5) (21.9) (23.9) 2.362 0.138 0.453 0.575 0.862 0.941 (60.0) (3.5) (11.5) (14.5) (21.9) (23.9) 2.559 0.138 0.500 0.736 1.031 1.165 (65.0) (3.5) (12.7) (18.7) (26.2) (29.6) 2.559 0.138 0.500 0.819 1.031 1.165 (65.0) (3.5) (12.7) (20.8) (26.2) (29.6) 2.559 0.138 0.500 0.969 1.358 1.488 (65.0) (3.5) (12.7) (24.6) (34.5) (37.8) 2.559 0.138 0.500 1.063 1.358 1.488 (65.0) (3.5) (12.7) (27.0) (34.5) (37.8) 2.756 0.138 0.598 1.311 1.717 1.882 (70.0) (3.5) (15.2) (33.3) (43.6) (47.8) 3.150 0.138 0.598 1.516 1.717 1.882 (80.0) (3.5) (15.2) (38.5) (43.6) (47.8) 3.150 0.138 0.610 1.898 2.070 2.276 (80.0) (3.5) (15.5) (48.2) (52.6) (57.8) 1.427 (36.2) 1.458 (37.0) 1.482 (37.6) 1.487 (37.8) 1.862 (47.3) 1.651 (41.9) 1.926 (48.9) 1.677 (42.6) 2.051 (52.1) 2.114 (53.7) 2.364 (60.0) 2.364 (60.0) 2.615 (66.4) 2.615 (66.4) 2.837 (72.1) 2.895 (73.5) 3.020 (76.7) 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 DIMENSIONS 3108 B THREAD CLASS 2A .5000-28UNEF .5000-28UNEF .6250-24NEF .6250-24NEF .6250-24NEF .7500-20UNEF .7500-20UNEF .8750-20UNEF .8750-20UNEF 1.0000-20UNEF 1.1875-18NEF 1.1875-18NEF 1.4375-18NEF 1.4375-18NEF 1.7500-18NS 2.0000-18NS 2.2500-16UN All dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 37 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 DIMENSIONS PRINTED CIRCUIT CONTACTS USE AIT OR SHELL AMPHENOL SIZE PART NUMBER A THREAD CLASS 2A M +.010 -.000 P R (TP) S REF. +/-.005 +/- .031 T DIA. +.004 3102 -.002 REF. L KK DIA. +.010 -.000 X REF. Y REF. +/-.045 8S 10-602460-XXX .5000-28UNEF 0.562 0.110 0.594 0.875 0.120 0.969 0.375 0.595 0.188 (14.3) (2.8) (15.1) (22.2) (3.0) (24.6) (9.5) (15.1) (4.8) 10S 10-602461-XXX .6250-24NEF 0.562 0.110 0.719 1.000 0.120 0.969 0.500 0.595 0.188 (14.3) (2.8) (18.3) (25.4) (3.0) (24.6) (12.7) (15.1) (4.8) 10SL 10-602462-XXX .6250-24NEF 0.562 0.110 0.719 1.000 0.120 0.969 0.625 0.595 0.188 (14.3) (2.8) (18.3) (25.4) (3.0) (24.6) (15.9) (15.1) (4.8) 12S 10-602463-XXX .7500-20UNEF 0.562 0.110 0.812 1.094 0.120 0.969 0.625 0.595 0.188 (14.3) (2.8) (20.6) (27.8) (3.0) (24.6) (15.9) (15.1) (4.8) 12 10-602464-XXX .7500-20UNEF 0.750 0.110 0.812 1.094 0.120 1.344 0.625 0.782 0.188 (19.1) (2.8) (20.6) (27.8) (3.0) (34.1) (15.9) (19.9) (4.8) 14S 10-602465-XXX .8750-20UNEF 0.562 0.110 0.906 1.188 0.120 0.969 0.750 0.595 0.188 (14.3) (2.8) (23.0) (30.2) (3.0) (24.6) (19.1) (15.1) (4.8) 14 10-602466-XXX .8750-20UNEF 0.750 0.110 0.906 1.188 0.120 1.344 0.750 0.782 0.188 (19.1) (2.8) (23.0) (30.2) (3.0) (34.1) (19.1) (19.9) (4.8) 16S 10-602467-XXX 1.0000-20UNEF 0.562 0.110 0.969 1.281 0.120 0.969 0.875 0.595 0.188 (14.3) (2.8) (24.6) (32.5) (3.0) (24.6) (22.2) (15.1) (4.8) 16 10-602468-XXX 1.0000-20UNEF 0.750 0.110 0.969 1.281 0.120 1.344 0.875 0.782 0.188 (19.1) (2.8) (24.6) (32.5) (3.0) (34.1) (22.2) (19.9) (4.8) 18 10-602469-XXX 1.1250-18NEF 0.750 0.141 1.062 1.375 0.120 1.344 1.000 0.782 0.188 (19.1) (3.6) (27.0) (34.9) (3.0) (34.1) (25.4) (19.9) (4.8) 20 10-602470-XXX 1.2500-18NEF 0.750 0.141 1.156 1.500 0.120 1.344 1.125 0.782 0.188 (19.1) (3.6) (29.4) (38.1) (3.0) (34.1) (28.6) (19.9) (4.8) 22 10-602471-XXX 1.3750-18NEF 0.750 0.141 1.250 1.625 0.120 1.344 1.250 0.782 0.188 (19.1) (3.6) (31.8) (41.3) (3.0) (34.1) (31.8) (19.9) (4.8) 24 10-602472-XXX 1.5000-18NEF 0.812 0.141 1.375 1.750 0.147 1.406 1.375 0.782 0.188 (20.6) (3.6) (34.9) (44.5) (3.7) (35.7) (34.9) (19.9) (4.8) 28 10-602473-XXX 1.7500-18NS 0.812 0.141 1.562 2.000 0.147 1.406 1.625 0.782 0.188 (20.6) (3.6) (39.7) (50.8) (3.7) (35.7) (41.3) (19.9) (4.8) 32 10-602474-XXX 2.0000-18NS 0.875 0.156 1.750 2.250 0.173 1.469 1.875 0.782 0.188 (22.2) (4.0) (44.5) (57.2) (4.4) (37.3) (47.6) (19.9) (4.8) 36 10-602475-XXX 2.2500-16UN 0.875 0.156 1.938 2.500 0.173 1.469 2.062 0.782 0.188 (22.2) (4.0) (49.2) (63.5) (4.4) (37.3) (52.4) (19.9) (4.8) 40 10-602476-XXX 2.5000-16UN 0.875 0.156 2.188 2.750 0.173 1.469 2.312 0.782 0.188 (22.2) (4.0) (55.6) (69.9) (4.4) (37.3) (58.7) (19.9) (4.8) XXX = Insert layout code. Contact us for correct code. Contact information is below. All dimensions in inches (millimeters in parenthesis) 38 For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com PANEL CUTOUTS SHELL SIZE FLANGE STYLE 0-2-6B MOUNTING HOLE FRONT MOUNT DIAMETER G Dimension J is flange in front of panel. Dimension K is flange at rear of panel. See sealing screws on a page 439. H J REAR MOUNT K 8S 0.594 (15.1) 0.134 (3.4) 0.396 (10.1) 0.603 (15.4) 10S 0.717 (18.2) 0.134 (3.4) 0.525 (13.3) 0.728 (18.5) 10SL 0.717 (18.2) 0.134 (3.4) 0.646 (16.4) 0.728 (18.5) 12S/12 0.811 (20.6) 0.134 (3.4) 0.646 (16.4) 0.854 (21.7) 14S/14 0.906 (23.0) 0.134 (3.4) 0.776 (19.7) 0.980 (24.9) 16S/16 0.969 (24.6) 0.134 (3.4) 0.902 (22.9) 1.091 (27.7) 18 1.063 (27.0) 0.134 (3.4) 1.028 (26.1) 1.224 (31.1) 20 1.157 (29.4) 0.134 (3.4) 1.161 (29.5) 1.358 (34.5) 22 1.252 (31.8) 0.134 (3.4) 1.287 (32.7) 1.488 (37.8) 24 1.374 (34.9) 0.154 (3.9) 1.417 (36.0) 1.626 (41.3) 28 1.563 (39.7) 0.154 (3.9) 1.654 (42.0) 1.854 (47.1) 32 1.752 (44.5) 0.177 (4.5) 1.902 (48.3) 2.118 (53.8) 36 1.937 (49.2) 0.177 (4.5) 2.150 (54.6) 2.362 (60.0) 40 2.185 (55.5) 0.177 (4.5) 2.409 (61.2) 2.610 (66.3) ++ 6B panel plug is front mount only. 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 DIMENSIONS PANEL THICKNESS Max screwhead Max screwhead & panel thickness SHELL SIZE .125 (3.18) 10S .125 (3.18) 10SL .125 (3.18) 12S/12SL .125 (3.18) 12 .187 (4.75) 14S .187 (4.75) 16S .187 (4.75) 16 18 Front Mount Rear Mount FRONT MOUNT REAR MOUNT 8SL .125 (3.18) .187 (4.75) .187 (4.75) 20 .187 (4.75) 22 .187 (4.75) 24 .187 (4.75) 28 .187 (4.75) 32 .250 (6.35) 36 .250 (6.35) 40 .250 (6.35) All dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 39 AIT/MS AMPHENOL INDUSTRIAL THREADED/MS/MIL-DTL-5015 SERIES Pre-Earth Series/FMLB FIRST-MATE, LAST-BREAK (FMLB) CONNECTOR THAT INTERMATES WITH MIL-DTL-5015 Amphenol’s DL Pre-Earth /FMLB (first-mate, last-break) connectors are designed for applications where a protective circuit from the ground contact to the shell is a safety requirement. These connectors provide a path for stray voltage to be shunted to a safe ground to avoid damage to sensitive equipment or harm to operators. • Intermateable with AIT, MIL-DTL-5015 & 97 series • UL-listed APPLICATIONS • Power generators FEATURES • Engines • Sensors •C  onformity with European (CE) safety standards (DIN VDE 0627 and certified through TUV Product Service GmbH) in the approved insert arrangement •O  ffered in shell styles: 3102A box mount and 3106A straight plug • Motion control • Off-road vehicles • Earth-moving equipment • Intermateable with AIT, MIL-DTL-5015 and 97 styles • Ships • Class IP67 protection when mated • Mobile equipment • UL-listed file # E202200 • Industrial machinery • Pre-earth (ground contact) design • Telecommunications • First-mate/last-break capability CREATE YOUR PART NUMBER USING THESE THREE STEPS 1 2 3 DL3106A 18-10 S CONNECTOR TYPE LAYOUT CONTACT STEP 1: S E L E C T S H E L L ST Y L E PLUGS RECEPTACLES STEP 2: S EL ECT L AYOUT (example) LAYOUT CURRENT RATING (AMPS) 13A 23A 46A CONTACT SIZE TOTAL MATING VIEW OF PIN INSERT CONTACTS 16 12 8 10SL-3 A 18-10 D A C B F E 18-12 3 3 - - 4 - 4 - 6 6 - - 7 - 7 - 4 - - 4 B 7 - - 7 B 7 - C B A D B C 20-15 F E A G B D DL3106A Plug DL3102A Box Mount Receptacle 22-22 24-106* 24-10 C D A C B F E G D F E D A C G A • Indicates Pre-Earth contact only STEP 3: S E L E C T C O N TA CT 40 - 7 C *Pre-Earth contact in plug P = Pin S = Socket For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com MS3057-A CABLE CLAMP Standard MS3057 cable clamps have dual-clamping action to provide a balanced, positive hold on the wires and greatly reduce moisture transmission. This cable clamp accepts MS3420 bushings. MS3420 bushings can be nested to reduce the inside diameter (ID) to more closely match the diameter of the cable or wire bundle. STANDARD CLAMP STANDARD CLAMP & TELESCOPIC BUSHING LOW-COST ZINC WITH BUSHING BUSHING INCLUDED BUSHING ID INCH (MM) 0.250 (6.35) - MS3420-3 0.130 (3.3) 0.312 (7.92) 97-3057-1004-1 MS3420-4 0.220 (5.6) M85049/41-4A 0.312 (7.92) 97-3057-1004-1 MS3420-4 0.220 (5.6) MS3057-6A M85049/41-6A 0.438 (11.10) 97-3057-1007-1 MS3420-6 0.312 (7.9) 97-3057-1008** MS3057-8A M85049/41-8A 0.562 (14.27) 97-3057-1008-1 MS3420-8 0.437 (11.1) 0.562 (14.3) ALUMINUM W/ MAXIMUM ALUMINUM W/ STAINLESS STEEL CABLE DIAMETER BRASS SCREWS SCREWS INCH (MM) SHELL SIZE THREAD CLASS 2B 8S/10S 1/2-28UNEF - MS3057-3A M85049/41-3A 10SL 5/8-24UNEF 97-3057-1004** MS3057-4A M85049/41-4A 12/12S 5/8-24UNEF 97-3057-1004** MS3057-4A 12SL/14S 3/4-20UNEF 97-3057-1007** 16/16S 7/8-20UNEF LOW-COST CAST ZINC 18 1-20UNEF 97-3057-1010** MS3057-10A M85049/41-10A 0.625 (15.88) 97-3057-1010-1 MS3420-10 20/22 1 3/16-18UNEF 97-3057-1012** MS3057-12A M85049/41-12A 0.750 (19.05) 97-3057-1012-1 MS3420-12 0.625 (15.9) 24/28 1 7/16-18UNEF 97-3057-1016** MS3057-16A M85049/41-16A 0.938 (23.80) 97-3057-1016-1 MS3420-16, -12 0.625 (15.9) 32 1 3/4-18UNS 97-3057-1020** MS3057-20A M85049/41-20A 1.250 (31.75) 97-3057-1020-1 MS3420-20, -16 0.750 (19.1) 36 2-18UNS 97-3057-1024** MS3057-24A M85049/41-24A 1.375 (34.92) 97-3057-1024-1 MS3420-24, -20 0.937 (23.8) 40 2 1/4UNS-16 - MS3057-28A M85049/41-28A 1.625 (41.28) - - - Default plating is CAD OD. ** Other platings are available. a See page 17. MS3057-C WATERPROOF CABLE CLAMP 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 ACCESSORIES Standard MS3057-C waterproof cable clamp with mechanical strain relief for use with threaded endbells. Internal neoprene gland and compression ring will seal a broad range of round cable diameters, as listed below. For reduction of cable diameters, order the appropriate MS3420A bushing in table. SHELL SIZE 8S/10S PART NUMBER WIRE DIAMETER INCHES (MM) MAX. MIN. OPTIONAL BUSHINGS PART NUMBER MAX. WIRE DIA. (MM) MS3057-3C 0.219 (5.56) 0.095 (2.41) MS3420-3A 0.125 (3.17) 10SL/12S/12 MS3057-4C 0.312 (7.93) 0.188 (4.80) MS3420-4A 0.219 (5.56) MS3057-6C 0.438 (11.12) 0.281 (7.10) MS3420-6A 0.312 (7.93) 12SL/14S MS3420-4A 0.219 (5.56) MS3420-8A 0.438 (11.1) MS3420-6A 0.312 (7.93) MS3420-10A 0.438 (11.1) 16/16S 18 MS3057-8C MS3057-10C 0.530 (13.48) 0.625 (15.87) 0.312 (7.90) 0.375 (9.50) MS3420-6A 0.312 (7.93) MS3420-12A 0.540 (13.74) 20/22 MS3057-12C 0.750 (19.00) 0.500 (12.70) MS3420-8A 0.438 (11.10) MS3420-16A 0.750 (19.00) 24/28 MS3057-16C 0.940 (23.80) 0.625 (15.90) MS3420-12A 0.540 (13.74) MS3420-8A 0.438 (11.10) MS3420-20A 0.938 (23.8) MS3420-16A 0.750 (19.00) MS3420-12A 0.540 (13.74) MS3420-24A 1.12 (28.50) MS3420-18A 0.938 (23.80) MS3420-16A 0.750 (19.00) MS3420-28A 1.25 (31.75) MS3420-20A 0.940 (23.80) MS3420-16A 0.750 (19.00) 32 MS3057-20C 1.250 (31.75) 0.921 (23.40) 36 MS3057-24C 1.380 (35.00) 1.00 (25.40) 40 MS3057-28C 1.620 (41.25) 1.25 (31.80) All dimensions in inches (millimeters in parenthesis) For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 41 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 ACCESSORIES MS3420 TELESCOPING BUSHINGS For use with style-A cable clamps and AIT/MS style-E/F endbells to resist dust, dirt, and oil. Bushings can be nested, one inside the other, to reduce the inside diameter to better seal against the cable jacket. Each bushing will accept the next smallest bushing. SHELL SIZE 1ST BUSHING PART NUMBER INSIDE DIAMETER 2ND NESTED BUSHING INSIDE DIAMETER FITS IN CABLE CLAMP 8S/10S MS3420-3 0.130 (3.30) NONE - MS3057-3A 10SL/12/12S MS3420-4 0.220 (5.59) NONE - MS3057-4A 14/14S MS3420-6 0.312 (7.92) NONE - MS3057-6A 16S MS3420-8 0.437 (11.10) NONE - MS3057-8A 16 MS3420-8 0.437 (11.10) NONE - MS3057-8A 18 MS3420-10 0.562 (14.30) NONE - MS3057-10A 20 MS3420-12 0.625 (15.90) NONE - MS3057-12A 22 MS3420-12 0.625 (15.90) NONE - MS3057-12A 24 MS3420-16 0.750 (19.05) MS3420-12 0.625 (15.90) MS3057-16A 28 MS3420-16 0.750 (19.05) MS3420-12 0.625 (15.90) MS3057-16A 32 MS3420-20 0.937 (23.80) MS3420-16 0.750 (19.05) MS3057-20A 36 MS3420-24 1.250 (31.75) MS3420-20 0.937 (23.80) MS3057-24A 40 MS3420-28 1.375 (34.92) MS3420-24 1.250 (31.75) SE96-28A4 MS3420-A REDUCTION BUSHINGS For use with MS3057-C cable clamps (style-C) to reduce the wire-sealing diameter. Bushings can be nested, one inside the other, to progressively reduce the inside diameter of the cable clamp. The column labeled “re­duction bushings” shows the acceptable nesting options for each clamp. 9767 CABLE CLAMPS 9767 waterproof cable clamp with mechanical strain relief. An internal Neoprene gland seal bushing and compression washer will seal a broad range of round cable diameters as listed below. SHELL SIZE CABLE CLAMP PART NUMBER MAX. CABLE OUTSIDE DIAMETER INCHES MM MIN. CABLE OUTSIDE DIAMETER INCHES MM THREAD CLASS 2B UNEF 10SL/12S/12 9767-12-4 0.219 5.55 0.100 0.51 5/8-24 14S 9767-14-4 0.219 5.55 0.100 0.51 3/4-20 14S 9767-14-6 0.344 8.73 0.176 4.47 3/4-20 16S/16 9767-16-4 0.219 5.55 0.100 0.51 7/8-20 16S/16 9767-16-6 0.344 8.73 0.176 4.47 7/8-20 16S/16 9767-16-8 0.438 11.12 0.177 4.50 7/8-20 18 9767-18-6 0.344 8.73 0.176 4.47 1-20 18 9767-18-8 0.438 11.12 0.177 4.50 1-20 18 9767-18-10 0.563 14.29 0.292 7.42 20/22 9767-22-8 0.438 11.12 0.177 4.50 1-3/16-18 20/22 9767-22-10 0.563 14.29 0.292 7.42 1-3/16-18 20/22 9767-22-12 0.688 17.46 0.370 9.40 1-3/16-18 24/28 9767-28-10 0.563 14.29 0.292 7.42 1-7/16-18 24/28 9767-28-12 0.688 17.46 0.370 9.40 1-7/16-18 24/28 9767-28-16 0.844 21.43 0.536 13.61 1-7/16-18 32 9767-32-20 1.031 26.19 0.590 14.99 1-3/4-18UNS 36 9767-36-16 0.844 21.43 0.536 13.61 1-20 2-18UNS All dimensions in inches (millimeters in parenthesis) 42 For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com GASKETS Synthetic rubber gaskets are used to ensure a moisture-tight seal between a receptacle and the panel. Gaskets are available for front or rear panel mounting of style-0, 2, and 6B connectors. Gasket thickness is approximately .031 inches (1 mm), for nonconductive and low-temperature types. Conductive shielding gaskets contain an imbedded metal screen for EMI/RFI shielding in addition to moisture sealing. Gaskets are available for front or rear panel mounting of connectors. Gasket thickness is .020 inches (.5 mm). SHELL SIZE NON-CONDUCTIVE CONDUCTIVE LOW-TEMPERATURE -67ºF (-55ºC) 8S 10-040450-008 10-040450-08S 10-036675-008 10S/10SL 10-040450-010 10-040450-10S 10-036675-010 12/12S 10-040450-012 10-040450-12S 10-036675-012 14/14S 10-040450-014 10-040450-14S 10-036675-014 16S 10-040450-016 10-040450-16S 10-036675-016 16 10-040450-016 10-040450-16S 10-036675-016 18 10-040450-018 10-040450-18S 10-036675-018 20 10-040450-020 10-040450-20S 10-036675-020 22 10-040450-022 10-040450-22S 10-036675-022 24 10-040450-024 10-040450-24S 10-036675-024 28 10-040450-028 10-040450-28S 10-036675-028 32 10-040450-032 10-040450-32S 10-036675-032 36 10-040450-036 10-040450-36S 10-036675-036 40 10-040450-040 10-040450-40S 10-036675-040 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 ACCESSORIES METAL DUST CAPS WITH SASH CHAIN & DUMMY RECEPTACLES Metal dust caps are used to protect the contacts when the connectors are left unmated. Dust caps come with metal chain lanyards. Dummy receptacles are for front or rear panel mounting. The center of the dummy receptacle is closed. Dummy receptacles mount on the same centers and have the same outside dimensions as MS3102 receptacles. A version with a clearance hole through the middle of the connector is also available. Call for ordering information; contact information is below. DUST CAPS RECEPTACLE PLUG CAP DUMMY RECEPTACLES SHELL SIZE 8S MS25042-8* MS25043-8* MS3105-8S 10S/10SL MS25042-10* MS25043-10* MS3105-10S 12/12S/12SL MS25042-12* MS25043-12* MS3105-12S 14S MS25042-14* MS25043-14* MS3105-14S 16S MS25042-16* MS25043-16* MS3105-16S 16 MS25042-16* MS25043-16* MS3105-16 18 MS25042-18* MS25043-18* MS3105-18 20 MS25042-20* MS25043-20* MS3105-20 22 MS25042-22* MS25043-22* MS3105-22 24 MS25042-24* MS25043-24* MS3105-24 28 MS25042-28* MS25043-28* MS3105-28 32 MS25042-32* MS25043-32* MS3105-32 36 MS25042-36* MS25043-36* MS3105-36 40 MS25042-40* MS25043-40* MS3105-40 *Contact us for other platings. *D = Olive drab chromate over cadmium DA = Anodized For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 43 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 ASSEMBLY INSTRUCTIONS SOLDER CONTACTS STEP 1: Slide the rear accessories over the wire bundle in the proper sequence for re-assembly: cable clamp and/or endbell first, then ferrule and (if used) coupling nut. STEP 2: Insert individual wires through the proper holes in the grommet. Use isopropyl alcohol as a lubricant. STEP 5: Slide the grommet down the wires (lubricating the grommet with isopropyl alcohol will help). STEP 3: Solder wires to appropriate contacts on the rear of the connector. Information on standard soldering practices is available upon request. Please contact us. STEP 6: Fill all unused grommet cavities with a wire hole filler to maintain the sealing integrity of the connector. STEP 4: Fixture the connector for reassembly using the endbell assembly tools on a page 122. STEP 7: Slide coupling nut, ferrule, and endbell accessories over rear of the connector and tighten. For tooling, a see page 122. CRIMP TOOL OPERATION LOCATOR LATCH CRIMP TOOL LOCATOR LATCH LOCATOR COLOR CODE INDEX MARK TURRET STEP 1: Strip the wires to the appropriate length. See strip lengths on the Contact Selection Guide, a page 30. STEP 2: Open the crimp tool by squeezing the handles. Push the latch on the turret to release the locator. Attach the turret to the crimp tool using the two captive hex bolts in the turret. NOTE: Hand-crimp tools can be used with size 16S, 16 & 12 contacts. Size 8, 4 and 0 contacts require the use of air-powered crimp tools. Contact us for assistance in the use of these tools. STEP 3: Select the proper locator position for your contact by rotating the locator until the proper color is aligned with the index mark. Push locator back down until it snaps into position. CONTACT SIZE PIN LOCATOR COLOR SOCKET LOCATOR COLOR 16S Blue 16 Green Blue Red 12 Red Red DIAL LOCK PIN STEP 4: Adjust dial for proper wire gauge. To change the dial setting, remove the lock pin and lift center of dial. Turn to the desired wire gauge. Replace lock pin on dial. 44 STEP 5: Cycle the tool before inserting the contact to be sure the tool is in the open position. Drop the contact, mating end first, into the crimp cavity of the tool. Squeeze the tool handle just enough to grip the contact without actually crimping it. STEP 6: Insert the stripped wire into the contact with a slight twisting motion. Be sure all wire strands are inside the contact. Squeeze the handle to cycle the tool. The handle will not release until the contact is completely crimped. For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com CRIMP TOOL OPERATION (CONTINUED) CRIMP TENSILE STRENGTH Initial minimum pullout force in lbs. (before conditioning) CHECK TO BE SURE CONDUCTOR IS VISIBLE THROUGH WIRE INSPECTION HOLE CRIMP WIRE INSULATION SHOULD PRESS AGAINST THE END OF THE CONTACT. SIZE WIRE GAUGE (AWG) LB. 16 20 20 18 40 16 50 12 14 70 12 110 8 8 185 4 4 450 0 0 800 STEP 7: Remove the crimped contact. Pull on the wire slightly to be sure it is properly crimped. Be sure the contact is not bent or damaged in any way. Visually inspect the crimp. MICRO-SECTIONS: Enlargement of micro-section permits a final inspection of crimp quality. This test is recommended whenever new tools or new types of wire or contacts are used. INSERTION OF CONTACTS GUIDE (PILOT) PIN INSERTION TOOL 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 ASSEMBLY INSTRUCTIONS SHOULDER STEP 1: Slide the rear accessories over the wire bundle in the proper sequence for re-assembly: cable clamp and/or endbell first, then ferrule, and coupling nut. STEP 2: Use the proper insertion tool from the Contact Selection Chart on a page 31. Place the contact in the tool. The tool should push against the shoulder of the contact. Contact sizes 16S, 16, and 12 use a pliers-style tool. Contact sizes 8, 4 and 0 use a tool with a C-shaped shaft. STEP 3: Lubricate the grommet with isopropyl alcohol (do not use any other type of lubricant). Insert the contact through the appropriate cavity in the grommet. Sizes 16S, 16 and 12 socket contacts must be installed using guide (pilot) pins. See the Contact Selection Guide on a page 31 for Insertion Guide (Pilot) Pin part numbers. CONNECTOR ASSEMBLY FIXTURE STEP 4: Place the connector into an assembly fixture. Fixtures are available for production use; contact us using the information below. If you are not using a fixture, be sure to allow clearance on the mating face of the connector for the guide pins to come through the connector during insertion. STEP 5: Lubricate the contact cavities of the connector insulator with isopropyl alcohol (do not use any other type of lubricant). STEP 6: Using guide pins where necessary, push straight down with a firm, even pressure until the contact snaps into position in the proper cavity. Start at the center of the pattern and work toward the outer edges. For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 45 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 ASSEMBLY INSTRUCTIONS INSERTION OF CONTACTS (CONTINUED) UNCRIMPED CONTACTS STEP 7: Fill any unused cavities with contacts. STEP 8: Check the mating face of the connector to ensure that all of the same size contacts are on the same plane (fully inserted). If not, the contact is not fully inserted. Remove the contact using the proper extraction tool and procedure, and reinsert. Do not attempt to reinsert the insertion tool to correct the problem. STEP 9: A wire hole filler must be inserted into the grommet behind the unused contacts to maintain the sealing integrity of the connector. See the Contact Selection Chart on a page 31 for wire hole fillers. STEP 10: Place the connector back in the fixture for re-assembly. Slide the connector accessories back down the cable over the rear of the connector and tighten. Use the appropriate endbell tools as shown on a page 122. EXTRACTION OF CONTACTS SOCKET EXTRACTION END SOFT JAW PLIERS LOCK RING HANDLE PIN EXTRACTION END STEP 1: Remove the endbell accessories and slide them back over the wires. Use the appropriate endbell tools as shown on a page 122. CROSS-SECTION OF CONNECTOR PIN CONTACT CROSS-SECTION OF CONNECTOR SOCKET CONTACT STEP 3: On the mating face of the connector, insert the tool over the pin contact or into the socket contact until the tool touches bottom. Apply a slow, continuous pressure to push the contact out through the rear of the connector. When the shoulder of the tool “thunks” against the insulator, the contact is extracted. 46 STEP 2: Use the proper extraction tool from the Contact Selection Chart on a page 31. The extraction tool can be used for both pin and socket contacts by removing the shaft from the handle and reversing it for pin or socket extraction. STEP 4: Carefully remove the extraction tool from the connector to avoid damage to the insulator. For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com AIT/MS SERIES CONNECTORS J MS 3102 R 18-3 P W -RES CONNECTOR TYPE (NOT J MS) J Prefix* MS Military Standard Modification for A-style service class only RESilient insert (neoprene) SHELL STYLE INSERT ROTATION 3100 = Wall-mounting receptacle 3101 = Cable-connecting receptacle (plug†) W, X, Y, and Z designate that the insert is rotated in its shell from normal position. No letter is required for normal (no rotation) position. See tables on a pages 83-93. Mates with 3102 = Box-mounting receptacle 3106 = Straight plug 3108 = 90° plug SERVICE CLASS CONTACT TYPES A Solid shell, not MS qualified P Pin contact C Solid shell for pressurized applications S Socket contact E Environmentally-resistant F Environmentally-resistant with strain relief (J MS part number only) R Lightweight, environmentally-resistant (J MS part number only; not available for 3108) SHELL SIZE & INSERT ARRANGEMENT See tables on a pages 72-93. 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 AMPHENOL HOW-TO-ORDER GUIDE † Note: The US military changed the designation from cable receptacle to plug in the MIL-DTL-5015 specifications. For insert arrangements over 50 and shell size 40 and above. Exceptions: 36-52, 40-1, 40-9 and 40-56 are approved. √ Parts are the only MS-approved inserts. *The March 30, 2003 revision of MIL-DTL-5015H requires that the letters JAN or J be physically marked on the connector preceding the MS designator. This mark certifies that the connector meets specification. The United States Government has obtained Certificate and Registration Number 504,860 for the certification mark “JAN” and Registration Number 1,586,261 for the certification mark “J.” HAVE A UNIQUE REQUIREMENT? Quick assembly of custom products is our specialty! Email us at sales@peigenesis.com or complete our online Technical Request at www.peigenesis.com/technical-support. To contact us by phone, please see the back cover for a complete listing of our branch offices and contact numbers. For assistance in Europe, please see the back cover for a complete listing of our branch offices and contact numbers. Specifications subject to change. 47 5015 - AMPHENOL AIT/MS SERIES MIL-DTL-5015 AMPHENOL HOW-TO-ORDER GUIDE AC SERIES CONNECTORS Ordering example part number ACC06AF18-1SX-025 is shown as follows: If part number incorporates a “B,” see AIB/GT a page 119. AC C 06 AF 18-1 S X - 025 SERIES AC PLATING MODIFICATION CODES Designates Amphenol Industrial Series CONTACT STYLE C Designates crimp contacts S Designates solder contacts CL Designates crimp contacts with low-smoke, zero-halogen insert and grommets Designates solder contacts with low-smoke, SL Mates with zero-halogen insert and grommets 003 Olive drab cadmium plate finish 023 Electroless nickel finish (RoHS with crimp only) 024 Green zinc alloy finish 025 Non-conductive black alloy finish (RoHS with crimp) 027 Conductive black alloy finish (RoHS with crimp) G96 Black hard-coat anodize SHELL STYLE A24 .000035 gold/nickel 00 Wall-mounting receptacle 01 In-line receptacle 116 Less pre-tinned solder cups 02 Box-mounting receptacle 06 Straight plug 472 116 & 025 mod codes (RoHS) 08 90˚ plug 548 116 & 023 mod codes (RoHS) 553 116 & 027 mod codes (RoHS) on contacts (solder only) CONNECTOR CLASS ALTERNATE INSERT ROTATION W, X, Y, and Z designate that the A General-duty, threaded backshell, cable clamp, no grommet AF General-duty, threaded backshell, cable clamp, no grommet CF General-duty, threaded backshell, gland-sealed cable clamp, no grommet (08 only) E General-duty, integral endbell with cable clamp, with grommet (08 not integral endbell) F General-duty, threaded backshell, cable clamp, with grommet LCFZ Long-threaded endbell, gland-sealed cable clamp, with grommet (06 only) PGA Environmental connector for jacketed cable PGR Environmental connector for jacketed cable R General-duty, threaded backshell, no cable clamp, with grommet (06 only) SB Shielded shrink boot endbell with grommet (06 only) insert is rotated in its shell from a normal position. No letter required for normal (no rotation) position. See a pages 83-93. CONTACT TYPE P Pin contacts S Socket contacts R RADSOK (high-amperage) crimp socket contacts only for sizes 12, 8, 4, and 0 SHELL SIZE & LAYOUT 48 See layout availability on a pages 72-93. For assistance in North America: +1 800.642.8750 for Pricing/Delivery or +1 800.523.0727 Tech Support • www.peigenesis.com • sales@peigenesis.com