HCSP-1BS-0400

Enabling the Electronics Revolution HCSP-1BS Automotive Open Loop Current Sensor - Busbar Mounting KEY FEATURES ▶ Open loop current transducer based on Hall effect ▶ Busbar mounting ▶ Simple analog ratiometric output ▶ Measured current value from ±200 A to ±1.500 A ▶ Non-intrusive technology ▶ Galvanic separation between power and control ▶ Operating temperature from -40°C to +125°C DESCRIPTION APPLICATIONS Piher Sensing Systems’ HCSP1BS family of open loop current sensors generates a ratiometric analog output voltage signal proportional to the current flowing through the conductor. Based on Hall effect technology the sensor has been designed for accurate measurement of AC and DC currents in automotive battery management and motor control applications. ▶ Battery management ▶ Motor control ▶ EV motor inverters ▶ DC/DC converters SPECIFICATIONS Parameter Unit Min. Typ. Max. Supply voltage V 4,5 5 5,5 Supply current mA 9 12 19 Output voltage V 0,5 Offset voltage V Response time µsec Frequency bandwidth kHz 70 250 Operating temperature °C -40 +125 Typical error (at 25°C; Vcc = 5V) % 0,65 2,5 Max. error (at -40°C to +125°C; Vcc = 5V) % 1 3,5 4,5 2,5 3 Other specifications on request Page 1 of 4 www.piher.net HCSP-1BS Automotive Open Loop Current Sensor - Busbar Mounting DIMENSIONS (IN MM) 51,0 Laser mark surface: 16,9 12,0 HCSP-1BS-0200 (02000= Current Variant from 200-1500) 3,0 N40 xxxxx (N40= Nº Week) (xxxxx= Universal Correlative part number for all current sensor) 8,0 ±0,15 4,2 = +0,15 0,00 +0,15 0,00 6,0 10 6,5 20,50 7,5 ±0,1 32,0 ±0,2 20,0 ±0,1 12,1 Tyco connector type P/N 1565749-1 4,2 +0,1,0 0 ) (2x 14,5 ±0,1 25,5 ±0,1 18,0 ±0,2 M4 Nut cavity (deep 4mm) 14,0 (nut not included) R5 Download the STEP file here: www.piher.net MOUNTING AND CONNECTIONS Connections Mounting Recommendation Mating connector TYCO 1473672-1 1 n/c 2 Supply voltage 3 Ground 4 Signal output Pin order -M4 screw -Spring washer -M4 nut (acc. to ISO 4032) -Max Torque: 2Nm Other pinouts on request Page 2 of 4 www.piher.net HCSP-1BS Automotive Open Loop Current Sensor - Busbar Mounting TESTS Operating temperature -40° to +125°C Thermal shock ISO 16750-4 5.3.2 (2010) Nº temperature cycles: 100 Temperature Profile: Tmax= +125ºC Thermal cycle ISO 16750-4 5.3.1 (2010) Chemical resistance ISO 16750-5 4.7 (2010) Salt spray ISO 16750-4 5.5.1 Sealing IP6K4 ISO 20653-02-2013 ISO 16750-3 4.1.2.4 - ISO 16750-3 4.1.1 27,1 m/s², 8h/axes 10Hz-1000Hz;Tª max: 125ºC ISO 60068-2-6:2007 ISO 16750-3 4.2.2 (2012) 50 g/6ms; 3 axis; 10 shocks of each direction Vibration Shock Bulk current inmunity ISO 11452-4:2005 Radiated inmunity ISO 11452-2:2005 Trasients inmunity EN 61000-4-4:2013 Conducted emissions CISPR25:2008 ESD ISO 10605:2008 PERFORMANCE DATA HCSP-1BS-_ _ _ _ 0200 0300 0400 0500 0600 0700 0800 Current measuring range ±200 A ±300 A ±400 A ±500 A ±600 A ±700 A ±800 A Current nominal value ±200 A ±300 A ±400 A ±500 A ±600 A ±700 A ±800 A Sensitivity* 10 mV/A 6,66 mV/A 5 mV/A 4 mV/A 3,33 mV/A 2,85 mV/A 2,5 mV/A Sensitivity error* ± 0,6 % Electrical offset voltage* ± 3 mV HCSP-1BS-_ _ _ _ 0900 1000 1100 1200 1300 1400 1500 Current measuring range ±900 A ±1.000 A ±1.100 A ±1.200 A ±1.300 A ±1.400 A ±1.500 A Current nominal value ±900 A ±1.000 A ±1.100 A ±1.200 A ±1.300 A ±1.400 A ±1.500 A Sensitivity* 2,22 mV/A 2 mV/A 1,81 mV/A 1,67 mV/A 1,53 mV/A 1,42 mV/A 1,33 mV/A Sensitivity error* ± 0.6 % Electrical offset voltage* ± 3 mV *at 25°C / Vcc = 5V; Other specification on request Page 3 of 4 www.piher.net HCSP-1BS Automotive Open Loop Current Sensor - Busbar Mounting ORDER CODE (e.g. HCSP-1BS-0300) Family HCSP - Phase 1 Single 3* Triple Mounting B Busbar Output S Simple - Measuring Range ____ 0200 to 1.500 A D* Dual - Measuring Range 1st Output 2nd Output ____- ____ 0200 to 1.500 A *on request Please always use the latest updated datasheets and 3D models published on our website. Disclaimer: The product information in this catalog is for reference purposes. Please consult for the most up to date and accurate design information. Piher Sensors & Controls S.A., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Piher”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product described herein. Piher disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Piher’s terms and conditions of sale, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Piher. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Piher products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Piher for any damages arising or resulting from such use or sale. Please contact authorized Piher personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Information contained in and/or attached to this catalogue may be subject to export control regulations of the European Community, USA, or other countries. Each recipient of this document is responsible to ensure that usage and/or transfer of any information contained in this document complies with all relevant export control regulations. If you are in any doubt about the export control restrictions that apply to this information, please contact the sender immediately. For any Piher Exports, Note: All products / technologies are EAR99 Classified commodities. Exports from the United States are in accordance with the Export Administration Regulations. Diversion contrary to US law is prohibited. Rev:06102023 © 2023 Piher Sensors & Controls S.A CONTACT Piher Sensing Systems Polígono Industrial Municipal Vial T2, Nº22 31500 Tudela Spain sales@piher.net Europe: +34 948 820 450 Americas: +1 636 251 0855 Asia Pacific: +65 9641 8886 Page 4 of 4 www.piher.net