HT270

HT270 Handpistol for Clincher Male and Female connector User’s Guide CONTENTS 1. DESCRIPTION ...........................................................................................3 2. SPECIFICATIONS......................................................................................3 3. OPERATING INSTRUCTIONS..................................................................3 4. ADJUSTMENTS .........................................................................................3 5. MAINTENANCE ........................................................................................3 6. TECHNICAL APPLICATION.....................................................................5 7. PARTS ........................................................................................................8 8. CONTACT ...................................................................................................8 Instruction manual HT270 Date: 24-10-2003 Revision: 3 www.foehrenbach.be Page: 2/8 1. DESCRIPTION The Clincher connector handtool HT 270 is designed to terminate Clincher Male and Female connectors from 2 through 34 positions. 2. ?? ?? ?? ?? ?? SPECIFICATIONS FCI Clincher Male and Female connector Number of positions: 2 through 34 Product part number: Male clincher 66226-series Female clincher 65801-series Cable: flat conductor, flat cable or flexible circuitry Conductor width: 1.57 mm 3. 1. 2. 3. 4. 5. 6. 7. OPERATING INSTRUCTIONS Place the handtool in your hand, so that the movable handle (item 2) may be actuated by your thumb. Place Clincher connector on the anvil (item 23a). Place cable well positioned in the connector. Close handtool by moving the handle (item 2) and hold Clincher connector with cable in place. When the handtool is completely closed, the movable handle (item 2) may be returned to its standing position. Repeat procedure 1-4 when a Clincher connector is used with more than 4 positions. Close the connector. Note: The handtool has stops, which prevents opening the tool before the clinch action is complete. Should it be necessary, the stop can be released by turning the ratchet wheel at the back of the tool in the direction indicated by the two yellow arrows. Keep the movable handle under light pressure during this operation. 4. ADJUSTMENTS Adjusting clinch height 1. 2. 3. 4. 5. 6. 7. 5. Use enclosed hollow-head screw wrench number 2 and special wrench with the blue grip. (Hollow-head screw wrench number 2.5 is used for replacing clinch tooling only). After removing the two button cap screws (item 10) it is possible to turn the stop ring (item 9 and 9a) Place the handtool so that the FCI name plate side is up. Turn the eccentric pin (item 8) with special wrench one position in clockwise direction. Check the height of the clinch. If the clinch is still too high, then the eccentric pin should be turned one position further. If the height of the clinch is correct, remount the two button head cap screws (item 10). MAINTENANCE ?? ?? ?? ?? Regular checks must be made on pressplate and anvil. If necessary, these parts may be cleaned. Damaged parts must be replaced immediately. For part numbers see parts list (6.) Movable parts should be lightly oiled. For this purpose use the oil that is enclosed in the case. ?? For 20z copper, 0.0711/.0028 thick, laminated between two layers of polyester insulating material - total nominal thickness 0.260/.011: Instruction manual HT270 Date: 24-10-2003 Revision: 3 www.foehrenbach.be Page: 3/8 clinch height should be 0.91/.0360 + 0.076/.0030-0.025/.0010. ?? For 30z copper, 0.1067/.0042 thick, laminated between two layers of polyester insulating material - total nominal thickness 0.330/.013: clinch height should be 0.965/.038 ? 0.025/.0010. ?? For flex circuitry not conforming to IPC FC-2208 cable specification, a clinch height guide of 0.64/.025 added to the circuitry thickness should be used. Clinch height tolerance should be ? 0.025/.0010. Because of the variety of circuitry and types of conductive links, consult with a FCI technical representative for specific applications. Instruction manual HT270 Date: 24-10-2003 Revision: 3 www.foehrenbach.be Page: 4/8 6. TECHNICAL APPLICATION (TA-372) Instruction manual HT270 Date: 24-10-2003 Revision: 3 www.foehrenbach.be Page: 5/8 Instruction manual HT270 Date: 24-10-2003 Revision: 3 www.foehrenbach.be Page: 6/8 Note: Clinch height “x” Instruction manual HT270 Date: 24-10-2003 Revision: 3 www.foehrenbach.be Page: 7/8 7. PARTS see table item no part No 1 2 3 3a 4 5 6 7 8 9 9a 10 11 * 12 13 14 15 16 17 18 * 19 20 21 22 * 23 * 23a * 24 * 25 26 172380 a 190589 172382 172383 192650 172386 172387 a 172388 172389 172390 190582 5305-003-050 172391 172392 172393 172394 a 190583 172395 190591 172397 192651 5305-003-051 172399 173584 190592 192788 192654 192655 192656 ?? description Handle permanent Handle mobile Upper spacer plate Lower spacer plate Cover plate Holding plate Connecting plate Hinge pin Eccentric pin Stop ring, lower side Stop ring, upper side Button head cap screw M3x4 Pawl Extension spring No 19 Pin f 2x7.8 Extension spring No 35 Stop roll Guide pin Stud Connecting pin Shaft Button head cap screw M4x6 Thread bush crimper Washer f 4.3 DIN 125-ST Washer f 12/4.2x1.5 Press plate and anvil Press plate rotating Holder plate Spacer qty per assy 1 1 1 1 2 2 2 1 1 1 1 2 1 1 2 1 1 1 1 3 1 10 1 2 2 1 set 2 2 2 = recommended spare part(s) 8. CONTACT Föhrenbach Application Tooling Kampioenstraat 54 2020 Antwerpen Belgium Instruction manual HT270 Date: 24-10-2003 Revision: 3 www.foehrenbach.be Page: 8/8