IT300

4-20 mA configurable vibration transmitter module iT300 The iT300 transmitter provides an easy means to connect a standard IEPE vibration sensor to a PLC, DCS or SCADA system. The transmitter’s input provides power to and measures the signal from either an accelerometer, piezovelocity sensor or dual output sensor. The input circuitry has a wide frequency response, capable of measuring signals between 0.2 Hz and 20,000 Hz. Band 1 (adjustable) Band 2 (adjustable) The transmitter has two independent processing bands with flexible mapping options to two separate 4-20 mA analog outputs. The processing channels contain selectable integration, allowing input from accelerometers to be output as acceleration or velocity. Selectable band filters and detector types make it easy to tailor the processing to specific machines or applications. System architecture – input/output Key features • Accepts input from accelerometers (single or dual output) or piezovelocity sensors • Input signal is split into two independent processing bands • Measures real-time sensor bands, BOV, true peak and temperature (if applicable) • Built-in web server for custom configuration of bandwidth/detection type • 2 x 4-20 mA outputs, userdefined Power input 4-20 mA outputs • Text field for user entry of machine information Input/output µprocessor • Configurations can be stored • Selectable speed range • Manufactured in an approved ISO 9001 facility Certifications Note: Due to continuous process improvement, specifications are subject to change without notice. This document is cleared for public release. Wilcoxon Sensing Technologies An Amphenol Company 99256 Rev.D.1 10/18 8435 Progress Drive Frederick, MD 21701 USA Tel: +1 (301) 330-8811 Fax: +1 (301) 330-8873 info@wilcoxon.com buy.wilcoxon.com www.wilcoxon.com 1 4-20 mA configurable vibration transmitter module iT300 SPECIFICATIONS INPUT MAPPABLE OUTPUTS IEPE sensor type Temperature sensor input Single-ended, DC coupled 10 mV/°C 4-20 mA output 2 user-configurable, based on (5) mappable options IEPE power source +24 VDC, 4.5 mA Max loop resistance 500 Ω Sensitivity range: acceleration velocity 9 - 11,000 mV/g 9 - 11,000 mV/ips Full scale input range ± 10 VDC Output scaling1: acceleration velocity displacement g (m/sec2) - rms, peak, peak-peak ips (mm/sec) - rms, peak, peak-peak mils (mm) - rms, peak, peak-peak Frequency response Fmax options 0.2 - 20 kHz (-3 dB, -0.1 dB) 200, 500 Hz; 1, 2, 5, 10, 20 kHz Accuracy ± 0.2% of full scale, 100 Hz Output ranges1: acceleration velocity displacement 1 - 50 g (10 - 500 m/sec2) 0.1-5 ips (2-100 mm/sec) 10 - 200 mils (0.2 - 5.0 mm) ADC sampling rate 48 kbps, 24 bits delta-sigma ENVIRONMENTAL FFT resolution, windowing 1,600 lines, Hanning window Dynamic range >90 dB CONFIGURABLE OPTIONS Frequency bands 1 and 2 Sensor unit1 or single integration2 Fstart3 Fstop3 Detection type: rms, peak, pk-pk Fixed measurement bands True peak, BOV, temperature4 Temperature range –40° to +70°C (storage: –40°C to +85°C) Power 11 - 32 VDC, 3.8 watts max (158 mA at 24 VDC) Isolation 500 VAC Connection type screw terminal, 14 - 24 AWG Mounting 35 mm DIN rail Dimensions W x H x D: 22.5 x 99.2 x 114.5 mm Notes: Based on IEPE sensor type (accelerometer or piezovelocity).  2 Acceleration signal to velocity, velocity signal to displacement.  3 The available selections are affected by the Fmax setting.  4 786T style sensors only. 1 System architecture PLUS +24 VOLT POWER TOP TERMINAL BLOCK CONNECTORS POWER SUPPLY GROUND REAR POWER CONNECTION, #17 & #18 MIDDLE 2 X 4-20 mA OUTPUT LOOPS FRONT BLANK Terminal numbers and signal assignments IO Port Vibration sensor 1 – No connection 2 – Temperature sensor (in T+) 3 – Signal in / Sensor Power (IN+) 4 – Circuit Common (COM) Temperature dynamic output 5 – Circuit Common (COM) 6 – Temperature out (T) Sensor dynamic output 7 – Circuit Common (COM) 8 – Sensor out (SENS) 4-20 mA Loop B 13 – B14 – B+ 4-20 mA Loop A 15 – A16 – A+ Power input 17 – P18 – P+ Not used 19 – 20 – REAR PANEL MOUNTED T-BUS CONNECTOR (OPTIONAL) RJ-45 CONNECTOR FOR INTERFACING WITH PC EQUIPPED WITH SUPPORTED WEB BROWSER TO CONFIGURE MODULE BOTTOM TERMINAL BLOCK CONNECTORS FRONT REAR P+ PNO CONNECTION D(A) D(B) DYNAMIC OUTPUT SENSOR CONNECTION Note: Due to continuous process improvement, specifications are subject to change without notice. This document is cleared for public release. Wilcoxon Sensing Technologies An Amphenol Company 99256 Rev.D.1 10/18 8435 Progress Drive Frederick, MD 21701 USA Tel: +1 (301) 330-8811 Fax: +1 (301) 330-8873 info@wilcoxon.com buy.wilcoxon.com www.wilcoxon.com 2 Built-in web server iT300 Save & Enable Changes Settings changes do not take effect until the "Save & Enable Changes" button is pressed Abandon Changes Login Login required before any changes can be made Machine Information Location Machine ID Machine Location Machine Name Machine Name Measurement Point  IEPE Power Machine ID MACHINE INFORMATION Measurement Point User entry of machine identity Sensor Input Sensor Type Acceleration Sensitivity (mV/g)  100 Averaging Time 1 sec  5 kHz  Enabled Serial Number  SENSOR INPUT Sensor Serial Number User entry of sensor parameters Frequency Range F max F min FREQUENCY RANGE 5 Hz User selection of frequency analysis range Sensor Band Configuration Output Type F start (Hz) Band 1 Velocity  5 Band 2 Acceleration  5 F stop (Hz)  5000  5000 Detector Type  RMS   RMS  SENSOR BAND CONFIGURATION Analysis band type and frequency limits Measurement Results Present Level Result Unit Band 1 in/sec  1.000 in/sec Band 2 g  1.000 g True Peak g  1.417 g Temperature Fahrenheit  Results from each band in selectable units 32.0 °F Volts BOV MEASUREMENT RESULTS 12.1 Volts Current Loops Loop Source Full Scale Loop A Band 1  5  Loop B Disabled  5  Level in/sec Destination Force Loop Force Value (mA) 7.20 mA Loop A Dest   10  0.00 mA Loop B Dest   10  CURRENT LOOPS 4-20 mA mapping Network Configuration IP Address 192.168.0.100 Default Gateway 192.168.0.1 NETWORK CONFIGURATION Subnet Mask 255.255.255.0 MAC Address 00:50:C2:19:BF:FB Module Information Model iT300 Hardware Revision D8 Serial Number ENG2 Firmware Revision 1.01 Change Password Load Configuration from File Save Configuration to File Restore Factory Defaults Update Firmware Note: Due to continuous process improvement, specifications are subject to change without notice. This document is cleared for public release. Wilcoxon Sensing Technologies An Amphenol Company 99256 Rev.D.1 10/18 8435 Progress Drive Frederick, MD 21701 USA Default configuration. Consult full manual on configuring your PC network adaptor. Default user: user Default password: admin Remember to save your changes to have new values take effect. Tel: +1 (301) 330-8811 Fax: +1 (301) 330-8873 info@wilcoxon.com buy.wilcoxon.com www.wilcoxon.com 3