MS3126F12-10SW

ca_A1-A163.qxd:Layout 1 2/9/11 7:48 PM Page 1 ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 39 Cannon KPT/KPSE MIL-C-26482 Series I Connectors KPSE High performance crimp contact connectors KPSE High performance crimp contact connectors A Circular • High performance • Crimp termination • Closed entry socket contacts Series KPSE environmental, miniature circular, quick disconnect connectors are designed for the exacting requirements of today’s electronic industry. They are intermateable, intermountable and interchangeable with all connectors manufactured acc. to MIL-C-26482 and VG95328. 1 Standard MIL-C-26482 mates with any connector designed to MIL-C-26482 and VG 95328. 4 Contact retaining clip is completely encased in a tough plastic wafer to protect the clip from damage 2 Crimp, snap-in contacts are designed to MIL-C39029 and can be crimped with the standard M22520/1 crimp tool. Complete moisture sealing is achieved by combining four seals: shell, peripheral, interfacial and wire seals Closed-entry socket contacts eliminate damage from abuse by test probes and help to correct any misaligned pins during engagement Shell Seal is effected when the plug shell pushes against the sealing ring in the receptacle when the connectors are mated. Contact insertion is accomplished from the rear of the connector. When the contact is fully inserted, the clip tines snap securely behind the contact shoulder. Contact extraction is accomplished with a front-inserted tool. Pressing the tool plunger pushes the contact out through the rear of the connector. 3 Monobloc insulator does not leave any access to moisture and avoids interfacial empty space. Peripheral Seal around the edge of the pin insulator is designed so that mating the connector puts tension on the seal and greatly reduces compression set. Interfacial Seal is achieved by the insutor faces meeting when the plug and receptacle are mated. Wire Seal is accomplished by a multiple ripple design, exceeding the wire sealing requirements of MIL-C-26482. 5 Positive insert-to-shell mechanical retention with hard plastic wafer firmly locked into a groove in the shell, in addition to a strong adhesive bond between the insert and shell. Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A-39 ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 40 Cannon KPT/KPSE MIL-C-26482 Series I Connectors KPSE High performance crimp contact connectors How to order Circular A MS KSPE 3120 00 E E 18 18 - 32 32 P P X X * * SERIES PREFIX SHELL STYLE CLASS SHELL SIZE CONTACT ARRANGEMENT CONTACT TYPE ALTERNATE INSERT POSITION MODIFICATION CODE SERIES PREFIX KPSE -ITT Cannon prefix KPSR - ITT Cannon RoHS prefix MS -MIL-C-26482 prefix SHELL STYLE ITT Cannon designation 00 -wall mounting receptacle 01 -cable connecting plug 02 -box mounting receptacle (class E only) 06 -straight plug 07 -jam nut receptacle 08 -90º angle plug MS DESIGNATION 3120 - Wall mounting receptacle 3121 - Cable connecting receptacle 3122 - Box mounting receptacle 3124 - Jam nut receptacle 3126 - Straight plug CLASS A - general duty (not MS approved) B - general duty with strain relief (not MS approved) E - with a grommet seal (MS specification) F - grommet seal with strain relief (MS specification) J - gland seal with strain relief for jacketed cable (U.S. version) (not MS approved) P -for potting (MS specification) (U.S. version) SHELL SIZES 8, 10, 12, 14, 16, 18, 20, 22, and 24 CONTACT ARRANGEMENTS see page A-41 CONTACT TYPE P -Pin S -Socket ALTERNATE INSERT POSITION W, X, and Z (omit for normal), see page A-42 MODIFICATION CODE (Include Same Codes as KPT) A34 - Electroless nickel hardware, RoHS compliant (European version) A71 - Electroless nickel hardware (U.S. version RoHS compliant after 11/1/07)) A206 - Black zinc cobalt hardware (U.S. version, RoHS compliant) A232 - Black zinc cobalt hardware (European version, RoHS compliant) A233 - Green zinc cobalt hardware (European version) A408 - Extended Life Contact - Gold over Nickel DN - Shrink boot adapter for shell styles 00, 01, 06 and 07 (Class E only) DZ - Endbell for shielding braids and shrink boots. (Class E only) 07 - Clear chromate over cadmium hardware (U.S. version) 16 - Lanyard release (applicable to plug only) (U.S. version) 23 - Ground springs (applicable to plug only) F42 - connectors without endbell and related parts P9 = PG9 for shell #10 P11 = PG11 for shell #12 P13 = PG13,5 for shell #14 P16 = PG16 for shell #16 P21 = PG21 for shell #18 P21 = PG21 for shell #20 P21 = PG21 for shell #22 P29 = PG29 for shell #24 M12 M16 M20 M25 M25 M25 M32 M32 = = = = = = = = M12x1,5 M16x1,5 M20x1,5 M25x1,5 M25x1,5 M25x1,5 M32x1,5 M32x1,5 for for for for for for for for shell shell shell shell shell shell shell shell #10 #12 #14 #16 #18 #20 #22 #24 Consult factory for other modifications. Omit first digit (0) of shell style indication when using a modification code. Dimensions shown in inches (mm) Specifications and dimensions subject to change A-40 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 41 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Contact Arrangements LEGEND KPT KPSE Authorized per MIL-C-26482 (NAVY) Not MS approved ITTC proprietary VG95328 B A A Shell Size No. of Contacts Service Rating 8-2 2-#20 I 8-3 3-#20 I 8-3A 3-#20 I A F F B E E D D C D A F B C E 10-7 7-#20 I A B H F B 10-98 6-#20 I 10-6 6-#20 I A 8-33 3-#20 I 8-4 4-#20 I M J C D R 12-10 10-#20 I L M A B LN P C K U V R T S D J E H G F A M N B T U P C R D H S E G F J Shell Size No. of Contacts Service Rating 14-18 18-#20 I A 14-5 5-#16 II B D E F D C 16-23 22-#20 1-#16 I 16-26 26-#20 I 16-99 21-#20 2-#16 I C E 14A-4 COAX RG1884 14-22 4-#12 1-#20 I 14-19 19-#20 I B C D 16-8 8-#16 II (Not for Receptacle Shell Style 02) I C P D H G E F 14-15 14-#20 1-#16 I Shell Size 18 A B S T C U N Y Z D V M X E W L K J H G F B H B N R J 14-12 8-#20 4-#16 I R A B S T U C N a b V D M Z c Y X W E L F K J H G N G K K D C E A M L B J L F P A R S B M Y C Z T L X D W U V K E J H G F A A A H G M B E P 12-14 14-#20 I 12-8 8-#20 I 12-3 3-#16 II L K A H A B G K J C F E D H E D E D C C F Shell Size 16 K C B C Shell Size 14 B A G A C N Shell Size No. of Contacts Service Rating B B Shell Size 12 Shell Size 10 B G C AD A C B Circular Shell Size 8 C A A Drawing not to scale; face view of pin insert shown (socket view is opposite) P P R A J H G C L P c N b d A B U V C W D e X E a M D F S T R B K Y Z F L G K E 18-11 11-#16 II H J 18A28 26-#20 2-#16 I Shell Size 20 A S B R P d C e D N f b M a Z L K Shell Size No. of Contacts Service Rating Y J V W X W g i c E V f d P F b M L G K H H J S J E F R G X B 20-16 16-#16 II 20A-6 5-#12* I G *Note: Contacts are 1 Grounding Pin & 4 Standard Size 12 pins A N R X V K E h Z X H B i d T P D U V W G M E F e j c i N b 22-32 32-#20 I 22-21 21-#16 II d k R C e U S S c f J T R g Y K F G P b a L D T H Shell Size No. of Contacts Service Rating C S U J M A A N B P W L a L h b A Z a Y s X t CC V q p AA P f E F m k N M G g y H h i L J K 24A57 55-#20 2-#12 I t FF V r U T c K J CC p R C d D e y E f g z F G h AA BB H n P B KK LL DD i m k j N M L J K 24-61 61-#20 I Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com g H A-41 S C D X E F G 22-34 34-#20 I x JJ V f W Z A w NN EE MM PP q S b v GG HH s x z n w u X W e D GG HH BB R Shell Size No. of Contacts Service Rating LL JJ S FF KK U T v EE Z a Y c B d C u DD B Y Shell Size 24 W r Y P T F C R f P b n q c p e d N M L K j i F R G 20-39 37-#20 2-#16 I 20-24 24-#20 I G c d e N M T R g f P N e d m l Y A U n B C V h W i k c M b L X D Y E K a J 22-36 36-#20 I Z H F G X W V U j a s n c r p g R P d q h S N f M P G N J L R F H e K 22-41 27-#20 14-#16 I k AA GG y i FF x w h p A g HH EE v M f L K B C W X r CC D Z s DD a t u d e Y q BB z j V n m E l U T S C D b J 22-55 55-#20 I b c G H H J K L 20-41 41-#20 I B m i T A Z k F b p f P J E a n l q r g D Z m h H C Y k s T S B X V U D a E g D S E C Z m A W B Y k r h S R A X j i 20A-6* Shell Size 22 M U W V U T B V H C A N Z J D W K D E M L E C P F 18-32 32-#20 I 18-30 29-#20 1-#16 I B N H G A A M K D Y Z a C X h N L B U e R U c A T S T E F ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 42 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Alternate Insert Positions Face view of pin inserts N A W* X* Circular Z* Y* The five positions (W,X,Y,Z and Normal) differ in degree or rotation for various sizes and arrangements No. of Contacts 2 3 Shell Size 8 8 Arr. No. 8-2 8-3 W 58 60 X 122 210 Degrees of Rotation Y .- 3 3 3 4 5 5 5 6 6 7 8 8 10 11 8 8 12 8 14 14 20 10 10 10 12 16 12 18 8-3A* 8-33 12-3 8-4 14-5 14-22 20A-6* 10-6 10-98 10-7* 12-8 16-8 12-10 18-11 60 90 45 40 ** 90 90 90 ** 90 54 60 62 92 ** 180 180 ** 112 152 155 119 180 184 ** 270 240 ** 203 180 270 241 273 ** 270 ** 292 331 295 340 12 14 15 16 18 19 21 23 23 24 26 28 30 32 32 34 36 39 14 12 14 20 14 14 22 16 16 20 16 18 18 18 22 22 22 20 14-12 12-14* 14-15 20-16 14-18 14-19 22-21 16-23 16-99 20-24 16-26 18A26* 18-30 18-32 22-32 22-34 22-36* 20-39 43 ** 17 238 15 30 16 158 66 70 60 180 85 72 62 72 63 90 ** 110 318 90 165 135 270 156 145 193 138 145 142 144 144 ** 155 333 180 315 175 223 215 275 285 222 215 218 216 252 ** 234 347 270 349 340 290 338 350 265 288 298 288 333 41 41 55 57 61 20 22 22 24 24 20-41 22-41 22-55 24A57* 24-61 45 39 30 90 90 126 135 142 180 180 225 264 226 270 270 314 324 Z - * Contact arrangements not MIL-C-26482 qualified † Not available in KPSE LA, LBF, LE, L J and LP are connector overall lengths Dimensions shown in inches (mm) Specifications and dimensions subject to change A-42 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 43 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Wall Mounting Receptacles MS3110 (MS service class E,F,J,P) MS3120 (MS service class E,F,P) KPT00 KPSE00 SEE TERMINATION ASSEMBLY SEE TERMINATION ASSEMBLY M Q Thd. M K SOLDER KPT00/MS3110 A ±.003 (±.08) .471 (11.96) .588 (14.96) .748 (19.00) .873 (22.17) .998 (25.35) 1.123 (28.52) 1.248 (31.70) 1.373 (34.87) 1.498 (38.05) CRIMP KPSE00/MS3120 .140 RAD MAX R (TP) S GROMMET FOR TYPES A, B, J & P RECEPTACLE ASSEMBLY M K +.031 (+.79) R* ±.016 (±.41) -.000 (.00) (TP) .062 (1.57) .431 (10.95) .594 (15.09) .062 (1.57) .431 (10.95) .719 (18.26) .062 (1.57) .431 (10.95) .812 (20.62) .062 (1.57) .431 (10.95) .906 (23.01) .062 (1.57) .431 (10.95) .969 (24.61) .062 (1.57) .431 (10.95) 1.062 (26.97) .094 (2.39) .556 (14.12) 1.156 (29.36) .094 (2.39) .556 (14.12) 1.250 (31.75) .094 (2.39) .589 (14.96) 1.375 (34.92) S T Max. ±.005 (±.13) .828 (21.03) .120 (3.05) .954 (24.23) .120 (3.05) 1.047 (26.59) .120 (3.05) 1.141 (28.98) .120 (3.05) 1.234 (31.34) .120 (3.05) 1.328 (33.73) .120 (3.05) 1.453 (36.91) .120 (3.05) 1.578 (40.08) .120 (3.05) 1.703 (43.26) .147 (3.73) Q Thread Class 2A 7/16-28UNEF 9/16-24UNEF 11/16-24UNEF 13/16-20UNEF 15/16-20UNEF 1-1/16-18UNEF 1-3/16-18UNEF 1-5/16-18UNEF 1-7/16-18UNEF † Not available in KPSE *(TP) located within .010 T.P. with respect to diameter A and master keyway. Receptacles with Termination Assemblies LA V THD DA LJ LE LBF GBF DJ BE HBF LP HJ HJ BP .395 (10.03) MN TYPE A TYPE E TYPE B AND F Shell Size †8 10 12 14 16 18 20 22 24 Shell Size †8 10 12 14 16 18 20 22 24 DA Min. .335 (8.51) .466 (11.84) .591 (15.01) .700 (17.90) .830 (21.08) .948 (24.08) 1.043 (26.49) 1.198 (30.43) 1.293 (32.84) TYPE A LA Max. 1.58 (40.00) 1.58 (40.00) 1.58 (40.00) 1.58 (40.00) 1.58 (40.00) 1.58 (40.00) 1.728 (43.89) 1.728 (43.89) 1.738 (44.15) DJ Max./Min. .230/.168 (5.84/4.27) .312/.205 (7.92/5.21) .442/.338 (11.23/8.59) .539/.416 (13.56/10.57) .616/.550 (15.65/13.97) .672/.600 (17.07/15.24) .747/.634 (18.97/16.13) .846/.670 (21.49/17.02) .894/.740 (22.71/18.80) V Thread Class 2A 1/2-28UNEF 5/8-24UNEF 3/4-20UNEF 7/8-20UNEF 1-20UNEF 1-3/16-18UNEF 1-3/16-18UNEF 1-7/16-18UNEF 1-7/16-18UNEF TYPE J HJ Max. .828 (21.03) .891 (22.63) 1.016 (25.81) 1.141 (28.98) 1.203 (30.56) 1.469 (37.31) 1.469 (37.31) 1.656 (42.06) 1.750 (44.45) GBF Min. .115 (2.92) .178 (4.52) .302 (7.67) .365 (9.27) .490 (12.45) .615 (15.62) .615 (15.62) .740 (18.80) .790 (20.07) LJ Max. 2.271 (57.68) 2.271 (57.68) 2.411 (61.24) 2.599 (66.01) 2.943 (74.75) 3.172 (80.57) 3.610 (91.69) 3.766 (95.66) 3.985 (101.22) † Not available in KPSE LA, LBF, LE, L J and LP are connector overall lengths Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A-43 TYPE P TYPE J TYPE B and F HBF Max. .828 (21.03) .891 (22.63) 1.016 (25.81) 1.141 (28.98) 1.203 (30.56) 1.469 (37.31) 1.469 (37.31) 1.656 (42.06) 1.750 (44.45) LBF Max. 1.922 (48.82) 1.922 (48.82) 1.922 (48.82) 1.922 (48.82) 2.047 (51.99) 2.078 (52.78) 2.344 (59.54) 1.344 (34.14) 2.406 (61.11) BP Max. .608 (15.44) .734 (18.64) .858 (21.79) .984 (24.99) 1.110 (28.19) 1.234 (31.34) 1.360 (34.54) 1.484 (37.69) 1.610 (40.89) TYPE E BE LE Max. Max. .608 (15.44) 1.328 (33.73) .734 (18.64) 1.328 (33.73) .858 (21.79) 1.328 (33.73) .984 (24.99) 1.328 (33.73) 1.110 (28.19) 1.328 (33.73) 1.234 (31.34) 1.328 (33.73) 1.360 (34.54) 1.531 (38.89) 1.484 (37.69) 1.531 (38.89) 1.610 (40.49) 1.594 (40.49) TYPE P DP Min. .317 (8.05) .434 (11.02) .548 (13.92) .673 (17.09) .798 (20.27) .899 (20.83) 1.024 (26.01) 1.149 (29.18) 1.274 (32.36) LP Max. 1.453 (36.91) 1.453 (36.91) 1.453 (36.91) 1.453 (36.91) 1.453 (36.91) 1.453 (36.91) 1.672 (42.47) 1.672 (42.47) 1.734 (44.04) A Circular K Q THD GROMMET FOR TYPES E&F A DIA A DIA Shell Size †8 10 12 14 16 18 20 22 24 T DIA 4 MTG HOLES POLARIZING GROOVE ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 44 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Cable Connecting Plugs A MS3111 (MS service class E,F,J,P) MS3121 (MS service class E,F,P) KPT01 KPSE01 SEE TERMINATION ASSEMBLY SEE TERMINATION ASSEMBLY H P H Circular P A Dia. A Dia. GROMMET FOR TYPES A, B, J & P SOLDER KPT01/MS3111 Shell Size †8 10 12 14 16 18 20 22 24 POLARIZING GROOVE Y Dia. Q THD Q THD A ±.003 (±.08) .471 (11.96) .588 (14.94) .748 (19.00) .873 (22.17) .998 (25.35) 1.123 (28.52) 1.248 (31.70) 1.373 (34.87) 1.498 (38.05) P HJ ±.016 (±.41) .094 (2.39) .094 (2.39) .094 (2.39) .094 (2.39) .094 (2.39) .094 (2.39) .115 (2.92) .115 (2.92) .115 (2.92) GROMMET FOR TYPES E & F S CRIMP KPSE01/MS3121 +.031 (+.79) -.000 (-.00) .400 (10.16) .400 (10.16) .400 (10.16) .400 (10.16) .400 (10.16) .400 (10.16) .535 (13.59) .535 (13.59) .558 (14.43) PLUG ASSEMBLY S Max. .828 (21.03) .954 (24.23) 1.047 (26.59) 1.141 (24.99) 1.110 (28.98) 1.234 (31.34) 1.328 (33.73) 1.578 (40.08) 1.703 (43.26) Y Max. .958 (24.33) 1.082 (27.48) 1.176 (29.87) 1.270 (32.26) 1.364 (34.65) 1.458 (37.03) 1.582 (40.18) 1.708 (43.38) 1.832 (46.53) Q Thread Class 2A 7/16-28UNEF 9/16-24UNEF 11/16-24UNEF 13/16-20UNEF 15/16-20UNEF 1-1/16-18UNEF 1-3/16-18UNEF 1-5/16-18UNEF 1-7/16-18UNEF † Not available in KPSE *(TP) located within .010 T.P. with respect to diameter A and master keyway. Cable Connecting Plugs with Termination Assemblies LA V THD DA LJ LE LBF GBF HBF LP DJ BE HJ HJ BP .395 (10.03) MN TYPE A Shell Size †8 10 12 14 16 18 20 22 24 Shell Size †8 10 12 14 16 18 20 22 24 DA Min. .335 (8.51) .466 (11.84) .591 (15.01) .700 (17.90) .830 (21.08) .948 (24.08) 1.043 (26.49) 1.198 (30.43) 1.293 (32.84) TYPE A LA Max. 1.50 (38.00) 1.50 (38.00) 1.50 (38.00) 1.50 (38.00) 1.50 (38.00) 1.50 (38.00) 1.728 (43.89) 1.728 (43.89) 1.738 (44.15) DJ Max./Min. .230/.168 (5.84/4.27) .312/.205 (7.92/5.21) .442/.338 (11.23/8.59) .539/.416 (13.56/10.57) .616/.550 (15.65/13.97) .672/.600 (17.07/15.24) .747/.634 (18.97/16.13) .846/.670 (21.49/17.02) .894/.740 (22.71/18.80) TYPE B AND F V Thread Class 2A 1/2-28UNEF 5/8-24UNEF 3/4-20UNEF 7/8-20UNEF 1-20UNEF 1-3/16-18UNEF 1-3/16-18UNEF 1-7/16-18UNEF 1-7/16-18UNEF TYPE J HJ Max. .828 (21.03) .891 (22.63) 1.016 (25.81) 1.141 (28.98) 1.203 (30.56) 1.469 (37.31) 1.469 (37.31) 1.656 (42.06) 1.750 (44.45) TYPE E GBF Min. .115 (2.92) .178 (4.52) .302 (7.67) .365 (9.27) .490 (12.45) .615 (15.62) .615 (15.62) .740 (18.80) .790 (20.07) TYPE B and F HBF Max. .828 (21.03) .891 (22.63) 1.016 (25.81) 1.141 (28.98) 1.203 (30.56) 1.469 (37.31) 1.469 (37.31) 1.656 (42.06) 1.750 (44.45) LJ Max. 2.271 (57.68) 2.271 (57.68) 2.411 (61.24) 2.599 (66.01) 2.943 (74.75) 3.172 (80.57) 3.610 (91.69) 3.766 (95.66) 3.985 (101.22) TYPE J LBF Max. 1.922 (48.82) 1.922 (48.82) 1.922 (48.82) 1.922 (48.82) 2.047 (51.99) 2.078 (52.78) 2.344 (59.54) 1.344 (34.14) 2.406 (61.11) BP Max. .608 (15.44) .734 (18.64) .858 (21.79) .984 (24.99) 1.110 (28.19) 1.234 (31.34) 1.360 (34.54) 1.484 (37.69) 1.610 (40.89) TYPE P TYPE E BE LE Max. Max. .608 (15.44) 1.328 (33.73) .734 (18.64) 1.328 (33.73) .858 (21.79) 1.328 (33.73) .984 (24.99) 1.328 (33.73) 1.110 (28.19) 1.328 (33.73) 1.234 (31.34) 1.328 (33.73) 1.360 (34.54) 1.531 (38.89) 1.484 (37.69) 1.531 (38.89) 1.610 (40.49) 1.594 (40.49) TYPE P DP Min. .317 (8.05) .434 (11.02) .548 (13.92) .673 (17.09) .798 (20.27) .899 (20.83) 1.024 (26.01) 1.149 (29.18) 1.274 (32.36) LP Max. 1.453 (36.91) 1.453 (36.91) 1.453 (36.91) 1.453 (36.91) 1.453 (36.91) 1.453 (36.91) 1.672 (42.47) 1.672 (42.47) 1.734 (44.04) Dimensions shown in inches (mm) Specifications and dimensions subject to change A-44 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 45 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Box Mounting Receptacles MS3112 (MS service class E) MS3122 (MS service class E) KPT02 KPSE02 A M M N DIA A DIA N DIA K CRIMP KPSE02/MS3122 .140 RAD MAX R (TP) S K Z SOLDER KPT02/MS3112 Circular A DIA T DIA 4 MTG HOLES POLARIZING GROOVE L B RECEPTACLE ASSEMBLY Note: Connector does not accomodate backshell. Shell A Size ±.003 (±.08) B Max. K ±.016 (±.41) L Max. M +.031 (+.79) -.000 (-.00) N Dia. Max. R* (TP) S Max. T ±.005 Z Max. †8 .471 (11.96) .978 (24.84) .062 (1.57) 1.320 (33.07) .431 (10.95) .469 (11.91) .594 (15.09) .828 (21.03) .120 (3.05) .354 (8.99) 10 .588 (14.96) .978 (24.84) .062 (1.57) 1.320 (33.07) .431 (10.95) .593 (15.06) .719 (18.26) .954 (24.23) .120 (3.05) .354 (8.99) 12 .748 (19.00) .978 (24.84) .062 (1.57) 1.320 (33.07) .431 (10.95) .719 (18.26) .812 (20.62) 1.047 (26.59) .120 (3.05) .354 (8.99) 14 .873 (22.17) .978 (24.84) .062 (1.57) 1.320 (33.07) .431 (10.95) .843 (21.41) .906 (23.01) 1.141 (28.98) .120 (3.05) .354 (8.99) 16 .998 (25.35) .978 (24.84) .062 (1.57) 1.320 (33.07) .431 (10.95) .969 (24.61) .969 (24.61) 1.234 (31.34) .120 (3.05) .354 (8.99) 18 1.123 (28.52) .978 (24.84) .062 (1.57) 1.320 (33.07) .431 (10.95) 1.093 (27.76) 1.062 (26.97) 1.328 (33.73) .120 (3.05) .354 (8.99) 20 1.248 (31.70) 1.196 (30.38) .094 (2.39) 1.387 (34.72) .556 (14.12) 1.219 (30.96) 1.156 (29.36) 1.453 (36.91) .120 (3.05) .417 (10.59) 22 1.373 (34.87) 1.196 (30.38) .094 (2.39) 1.387 (34.72) .556 (14.12) 1.343 (34.11) 1.250 (31.75) 1.578 (40.08) .120 (3.05) .417 (10.59) 24 1.498 (38.05) 1.196 (30.38) .094 (2.39) 1.418 (36.02) .589 (14.96) 1.469 (37.31) 1.375 (34.92) 1.703 (43.26) .147 (3.73) .445 (11.30) † Not available in KPSE *(TP) located within .010 T.P. with respect to diameter A and master keyway. Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A-45 ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 46 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Straight Plugs MS3116 (MS service class E,F,J,P) MS3126 (MS service class E,F,P) KPT06 KPSE06 Q THD Q THD Circular A POLARIZING GROOVE A DIA A DIA SEE TERMINATION ASSEMBLY CRIMP KPSE06/MS3126 G SOLDER KPT06/MS3116 Shell Size †8 10 12 14 16 18 20 22 24 GROMMET FOR TYPES A, B, J & P GROMMET FOR TYPES E & F A Dia. Max. .765 (19.43) .840 (21.34) .999 (25.38) 1.139 (28.93) 1.261 (32.03) 1.337 (33.96) 1.477 (37.52) 1.602 (40.69) 1.723 (43.76) G Max. .782 (19.86) .926 (23.52) 1.043 (26.49) 1.183 (30.05) 1.305 (33.15) 1.391 (35.33) 1.531 (38.89) 1.656 (42.06) 1.777 (45.14) J ±.010 (±0.25) .353 (8.99) .353 (8.99) .353 (8.99)) .353 (8.99) .353 (8.99) .353 (8.99) .415 (10.54) .415 (10.54) .415 (10.54) Q Thread Class 2A 7/16-28UNEF 9/16-24UNEF 11/16-24UNEF 13/16-20UNEF 15/16-20UNEF 1-1/16-18UNEF 1-3/16-18UNEF 1-5/16-18UNEF 1-7/16-18UNEF † Not available in KPSE Straight Plugs with Termination Assemblies LA V THD DA LJ LE LBF GBF LP DJ BE HBF HJ HJ BP .395 (10.03) MN TYPE A TYPE B AND F Shell DA Size Min. †8 .335 (8.51) 10 .466 (11.84) 12 .591 (15.01) 14 .700 (17.90) 16 .830 (21.08) 18 .948 (24.08) 20 1.043 (26.49) 22 1.198 (30.43) 24 1.293 (32.84) Shell Size †8 10 12 14 16 18 20 22 24 TYPE A LA Max. 1.440 (36.58) 1.440 (36.58) 1.440 (36.58) 1.440 (36.58) 1.440 (36.58) 1.662 (42.21) 1.662 (42.21) 1.662 (42.21) 1.672 (42.47) DJ Max./Min. .230/.168 (5.84/4.27) .312/.205 (7.92/5.21) .442/.338 (11.23/8.59) .539/.416 (13.56/10.57) .616/.550 (15.65/13.97) .672/.600 (17.07/15.24) .747/.634 (18.97/16.13) .846/.670 (21.49/17.02) .894/.740 (22.71/18.80) TYPE J TYPE E V Thread Class 2A 1/2-28UNEF 5/8-24UNEF 3/4-20UNEF 7/8-20UNEF 1-20UNEF 1-3/16-18UNEF 1-3/16-18UNEF 1-7/16-18UNEF 1-7/16-18UNEF TYPE J HJ Max. .828 (21.03) .891 (22.63) 1.016 (25.81) 1.141 (28.98) 1.203 (30.56) 1.469 (37.31) 1.469 (37.31) 1.656 (42.06) 1.750 (44.45) GBF Min. .115 (2.92) .178 (4.52) .302 (7.67) .365 (9.27) .490 (12.45) .615 (15.62) .615 (15.62) .740 (18.80) .790 (20.07) TYPE B and F HBF Max. .828 (21.03) .891 (22.63) 1.016 (25.81) 1.141 (28.98) 1.203 (30.56) 1.469 (37.31) 1.469 (37.31) 1.656 (42.06) 1.750 (44.45) LJ Max. 2.271 (57.68) 2.271 (57.68) 2.411 (61.24) 2.599 (66.01) 2.943 (74.75) 3.172 (80.57) 3.610 (91.69) 3.766 (95.66) 3.985 (101.22) TYPE P LBF Max. 1.906 (48.41) 1.906 (48.41) 1.906 (48.41) 1.906 (48.41) 2.047 (51.99) 2.078 (52.78) 2.250 (57.15) 2.250 (57.15)) 2.312 (58.72) BP Max. .608 (15.44) .734 (18.64) .858 (21.79) .984 (24.99) 1.110 (28.19) 1.234 (31.34) 1.360 (34.54) 1.484 (37.69) 1.610 (40.89) TYPE E BE LE Max. Max. .608 (15.44) 1.328 (33.73) .734 (18.64) 1.328 (33.73) .858 (21.79) 1.328 (33.73) .984 (24.99) 1.328 (33.73) 1.110 (28.19) 1.328 (33.73) 1.234 (31.34) 1.328 (33.73) 1.360 (34.54) 1.453 (36.91) 1.484 (37.69) 1.453 (36.91) 1.610 (40.49) 1.510 (38.54) TYPE P DP Min. .317 (8.05) .434 (11.02) .548 (13.92) .673 (17.09) .798 (20.27) .899 (20.83) 1.024 (26.01) 1.149 (29.18) 1.274 (32.36) LP Max. 1.500 (38.10) 1.500 (38.10) 1.500 (38.10)) 1.500 (38.10) 1.500 (38.10) 1.500 (38.10) 1.609 (40.87) 1.609 (40.87) 1.687 (42.85) † Not available in KPSE LA, LBF, LE, L J and LP are connector overall lengths Dimensions shown in inches (mm) Specifications and dimensions subject to change A-46 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 47 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Jam Nut Receptacles MS3114 (MS service class E,F,P) MS3124 (MS service class E,F,P) KPT07 KPSE07 A M M Q THD A DIA K N DIA F MTG FLAT A DIA R THD R THD T A ±.003 (±.08) A H ±.005 (0.130) ±.017 (±.43) GROMMET FOR TYPE A,B&P S CRIMP KPSE07MS3124 SOLDER KPT07/MS3114 Shell Size GROMMET FOR TYPE E&F Circular K H K ±.020 (±.05) M +.031 (+.08) -.000 (-.00) N Max. S Max. T Panel Thickness Min. Max. R Thread Class 2A †8 .471 (11.96) .525 (13.34) .750 (19.05) .117 (2.97) .691 (17.55) 1.078 (27.38) .954 (15.09) .062 (1.57) .125 (3.17) 9/16-24UNEF 10 .588 (14.96) .650 (16.51) .875 (22.22) .117 (2.97) .691 (17.55) 1.206 (30.56) 1.078 (27.38) .062 (1.57) .125 (3.17) 11/16-24UNEF 12 .748 (19.00) .813 (20.65) 1.062 (26.97) .117 (2.97) .691 (17.55) 1.319 (35.33) 1.266 (32.16) .062 (1.57) .125 (3.17) 7/8-20UNEF 14 .873 (22.17) .937 (23.80) 1.188 (30.17) .117 (2.97) .691 (17.55) 1.516 (38.51) 1.391 (35.33) .062 (1.57) .125 (3.17) 1-20UNEF 16 .998 (25.35) 1.061 (26.95) 1.312 (33.32) .117 (2.97) .691 (17.55) 1.641 (41.68) 1.516 (38.51) .062 (1.57) .125 (3.17) 1-1/8-18UNEF 18 1.123 (28.52) 1.186 (30.12) 1.438 (36.25) .117 (2.97) .691 (17.55) 1.766 (44.86) 1.641 (41.68) .062 (1.57) .125 (3.17) 1-1/4-18UNEF 20 1.248 (31.70) 1.311 (33.30) 1.562 (39.67) .148 (3.76) .879 (22.33) 1.954 (49.63) 1.828 (46.43) .062 (1.57) .250 (6.35) 1-3/8-18UNEF 22 1.373 (34.87) 1.436 (36.47) 1.688 (42.87) .148 (3.76) .879 (22.33) 2.078 (52.78) 1.954 (49.63) .062 (1.57) .250 (6.35) 1-1/2-18UNEF 24 1.498 (38.05) 1.561 (39.65) 1.812 (46.02) .148 (3.76) .912 (23.16) 2.203 (55.96) 2.078 (52.78) .062 (1.57) .250 (6.35) 1-5/8-18UNEF † Not available in KPSE Jam Nut Receptacles with Termination Assemblies LBF TYPE A (No Term. Assy.) LP LE GBF HBF DP BE BP Z Shell Size †8 10 12 14 16 18 20 22 24 TYPE A Z Max. .312 (7.92) .312 (7.92) .312 (7.92) .312 (7.92) .312 (7.92) .312 (7.92) .193 (4.90) .193 (4.90) .150 (3.81) HBF Max. .828 (21.03) .891 (22.63) 1.016 (25.81) 1.141 (28.98) 1.203 (30.56) 1.469 (37.31) 1.469 (37.31) 1.656 (42.06) 1.750 (44.45) TYPE B and F GBF Min. .115 (2.92) .178 (4.52) .302 (7.67) .365 (9.27) .490 (12.45) .615 (15.62) .615 (15.62) .740 (18.80) .790 (20.07) LBF Max. 1.906 (48.41) 1.906 (48.41) 1.906 (48.41) 1.906 (48.41) 2.047 (51.99) 2.078 (52.78) 2.328 (59.13) 2.328 (59.13) 2.453 (62.31) TYPE E BE LE Max. Max. .655 (16.64) 1.344 (34.14) .843 (21.41) 1.344 (34.14) .968 (24.59) 1.344 (34.14) 1.093 (27.76) 1.344 (34.14) 1.218 (30.94) 1.344 (34.14) 1.343 (34.11) 1.344 (34.14) 1.500 (38.10) 1.594 (40.49) 1.625 (41.28) 1.594 (40.49) 1.750 (44.45) 1.641 (41.68) LBF, LE, and LP are connector overall lengths. Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A-47 BP Max. .608 (15.44) .734 (18.64) .858 (21.79) .984 (24.99) 1.110 (28.19) 1.234 (31.34) 1.360 (34.54) 1.484 (37.69) 1.610 (40.89) TYPE P DP Min. .317 (8.05) .434 (11.02) .548 (13.92) .673 (17.09) .798 (20.27) .899 (22.83) 1.024 (26.01) 1.149 (29.18) 1.274 (32.36) LP Max. 1.391 (35.33) 1.391 (35.33) 1.391 (35.33) 1.391 (35.33) 1.391 (35.33) 1.391 (35.33) 1.641 (41.68) 1.641 (41.68) 1.703 (43.26) ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 48 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Right Angle Plugs KPT08/KPSE08 A Q THD Circular Q THD GROMMET FOR TYPES E&F POLARIZING BOSS A DIA A DIA GROMMET FOR TYPES A,B,J&P G KPT08 KPSE08 KPT/KPSE Shell Size †8 10 12 14 16 18 20 22 24 A Dia. Max. .765 (19.43) .866 (22.00) 1.031 (26.20) 1.157 (29.40) 1.291 (32.80) 1.394 (35.40) 1.535 (39.00) 1.657 (42.10) 1.780 (45.20) G Max. .782 (19.86) .926 (23.52) 1.043 (26.49) 1.183 (30.05) 1.305 (33.15) 1.391 (35.33) 1.531 (38.89) 1.656 (42.06) 1.777 (45.14) Q Thread Class 2A 7/16-28UNEF 9/16-24UNEF 11/16-24UNEF 13/16-20UNEF 15/16-20UNEF 1-1/16-18UNEF 1-3/16-18UNEF 1-5/16-18UNEF 1-7/16-18UNEF † Not available in KPSE NOTE: for size 10 and 24 consult factory for availability in type A,B,E and F. For size 8 consult factory for availability in Type P. Right Angle Plugs with Termination Assemblies AP DBF DAE LAE Shell Max. †8 10 12 14 16 18 20 22 24 LAE Size 1.421 1.484 1.546 1.577 1.609 1.734 1.879 2.035 2.035 (36.09) (37.69) (39.27) (40.05) (40.87) (44.04) (47.73) (51.69) (51.69) TYPE A and E DAE Max. V Thread Max. .822 (20.88) .853 (21.67) .916 (23.27) .978 (24.84) 1.041 (26.44) 1.103 (28.70) 1.166 (29.62) 1.245 (31.62) 1.322 (33.58) 1/2-28UNEF 5/8-28UNEF 3/4-20UNEF 7/8-20UNEF 1-20UNEF 1-3/16-18UNEF 1-3/16-18UNEF 1-7/16-18UNEF 1-7/16-18UNEF CP LBF V THD L MAX DBF Class 2A 1.238 1.269 1.395 1.519 1.582 1.644 1.707 1.884 1.963 (31.44) (32.24) (35.43) (38.58) (40.18) (41.76) (43.36) (47.85) (49.86) TYPE B and F LBF Max. 1.421 1.484 1.546 1.577 1.609 1.734 1.879 2.035 2.035 (36.09) (37.69) (39.27) (40.05) (40.87) (44.04) (47.73) (51.69) (51.69) LP L Max. 1.842 1.937 2.091 2.173 2.238 2.455 2.629 2.815 2.902 (46.79) (49.20) (53.10) (55.20) (56.85) (62.35) (66.78) (71.51) (73.70) TYPE P LP Max. AP Max. -(-) 1.030 (26.16) 1.030 (26.16) 1.030 (26.16) 1.280 (32.51) 1.280 (32.51) 1.530 (38.86) 1.530 (38.86) 1.780 (45.21) -(-) 1.380 (35.05) 1.567 (39.80) 1.567 (39.80) 1.567 (39.80) 1.755 (44.58) 1.782 (45.26) 1.782 (45.26) 2.087 (53.01) CP Min. -(-) .252 (6.40) .252 (6.40) .283 (7.19) .355 (9.02) .530 (13.46) .562 (14.27) .562 (14.27) .610 (15.49) † Not available in KPSE. NOTE: For size 10 and 24 consult factory for availability in type A,B,E and F. For size 8 consult factory for availability in Type P. Dimensions shown in inches (mm) Specifications and dimensions subject to change A-48 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 49 Cannon KPT/KPSE MIL-C-26482 Series I Connectors KPSE High performance crimp contact connectors How to order acc. to VG 95328 VG 95328 A 18 - 1 S N A SPECIFICATION Circular SHELL STYLE SHELL SIZE CONTACT ARRANGEMENT CONTACT TYPE ALTERNATE INSERT POSITION SHELL SIZES 8, 10, 12, 14, 16, 18, 20, 22, and 24 SPECIFICATION SHELL STYLE A -wall mounting receptacle with straight endbell B -wall mounting receptacle with cable clamp C -box mounting receptacle D -jam nut receptacle E -jam nut receptacle with cable clamp J -straight plug with adapter DN K -straight plug with cable clamp M -straight plug, version DZ N -straight plug S -jam nut receptacle with adapter DN T -jam nut receptacle, version DZ CONTACT ARRANGEMENTS see page A-41 CONTACT TYPE P -Pin S -Socket ALTERNATE INSERT POSITION see page A-42 How to Order – KPTB Thru-Bulkhead Receptacle Connectors • • • • General Purpose Double ended pin and socket contacts Contains KPT socket insert Nonremovable contacts KPTB connectors are a series of general purpose, miniature circular connectors, qualified for use in military applications. They are also widely used in industrial applications. The KPTB in a thru-bulkhead version with double faced pin and socket insert construction allowing mating from both ends. They contain KPT socket inserts with feed-thru (pin/socket) non-removable contacts. The thru-bulkhead receptacle is provided for applications requiring the disconnection of a power source from either side of a panel. A typical connector to be used if air leakage requirements are critical. KPTB 22 - 55 PS SERIES PREFIX SHELL SIZE CONTACT ARRANGEMENT CONTACT STYLE (pin & socket) ALTERNATE INSERT POSITION MS3119 E 22 - 55 MIL-C-26482 PREFIX CLASS SHELL SIZE CONTACT ARRANGEMENT ALTERNATE INSERT POSITION MS3119 (MS service class E) KPTB (MS service class E) POLARIZING GROOVE T DIA. 4 MTG. HOLES L PIN SIDE A A SKT SIDE M K .140 RAD. MAX. R (TP) S TYP *(T.P.) located within .010 T.P. with respect to the diameter A and master keyway. Shell A Dia. K Size ±.003 (±.08) ±.016 (±.406) Y L Max. M +.031 (+.79) -.000 (-.00) R* (TP) S Max. T ±.005 (±.127) 8 .471 (11.96) .062 (1.57) 1.125 (28.58) .562 (14.27) .594 (15.09) 7/16-28UNEF .120 (3.05) 10 .588 (14.94) .062 (1.57) 1.125 (28.58) .562 (14.27) .719 (18.26) 9/16-24UNEF .120 (3.05) 12 .748 (19.00) .062 (1.57) 1.125 (28.58) .562 (14.27) .812 (20.62) 11/16-24UNEF .120 (3.05) 14 .873 (22.17) .062 (1.57) 1.125 (28.58) .562 (14.27) .906 (23.01) 13/16-20UNEF .120 (3.05) 16 .998 (25.35) .062 (1.57) 1.125 (28.58) .562 (14.27) .969 (24.61) 15/16-20UNEF .120 (3.05) 18 1.123 (28.52) .062 (1.57) 1.125 (28.58) .562 (14.27) 1.062 (26.97) 1-1/16-18UNEF .120 (3.05) 20 1.248 (31.70) .094 (2.39) 1.406 (35.71) .688 (17.48) 1.156 (29.36) 1-3/16-18UNEF .120 (3.05) 22 1.373 (34.87) .094 (2.39) 1.406 (35.71) .688 (17.48) 1.250 (31.76) 1-5/16-18UNEF .120 (3.05) 24 1.498 (38.05) .094 (2.39) 1.406 (35.71) .688 (17.48) 1.375 (34.92) 1-7/16-18UNEF .147 (3.73) Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com Y A-49 ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 50 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Dummy Receptacles Circular A How To Order KPT 15 - 12A • .140 RAD. Max SERIES PREFIX G DIA 4 HOLES DUMMY RECEPTACLE INDICATOR SHELL SIZE A DIA. J E K F MODIFICATIONS NOTE: For MS Version and additional finishes see PV catalog SERIES PREFIX KPT - ITT Cannon Prefix SHELL SIZE 8 THRU 24 MODIFICATIONS None-Olive drab chromate over cadmium Shell Size A ±.003 (.08) E Basic F Max. G ±.005 (.13) J +.031 (.79) -.000 (.00) K ±.016 (.41) 8 .471 (11.96) .594 (15.09) .828 (21.03) .120 (3.05) .462 (11.73) .062 (1.57) 10 .588 (14.94) .719 (18.26) .954 (24.23) .120 (3.05) .462 (11.73) .062 (1.57) 12 .748 (19.00) .812 (20.62) 1.047 (26.60) .120 (3.05) .462 (11.73) .062 (1.57) 14 .873 (22.17) .906 (23.01) 1.141 (28.98) .120 (3.05) .462 (11.73) .062 (1.57) 16 .998 (25.35) .969 (24.61) 1.234 (31.34) .120 (3.05) .462 (11.73) .062 (1.57) 18 1.123 (28.52) 1.061 (26.97) 1.328 (33.73) .120 (3.05) .462 (11.73) .062 (1.57) 20 1.248 (31.70) 1.156 (29.36) 1.453 (36.91) .120 (3.05) .556 (14.12) .094 (2.39) 22 1.373 (34.87) 1.250 (31.75) 1.578 (40.08) .120 (3.05) .556 (14.12) .094 (2.39) 24 1.498 (38.05) 1.375 (34.93) 1.703 (43.26) .147 (3.73) .589 (14.96) .094 (2.39) Protective Caps How To Order KPT 80 12 C 81 - Cap for receptacle 80 - Cap for plugs • SERIES PREFIX .094 (2.39) Max. R TYPE SHELL SIZE L TERMINATION STYLE .047 (1.19) Max. .169 (4.29) ±.008 (.20) F A Q H+.500 (12.7) -.250 (6.35) CHAIN LENGHT MODIFICATIONS M Q H+.500 (12.7) -.250 (6.35) CHAIN LENGHT SERIES PREFIX KPT - ITT Cannon Prefix TYPE 80 - Plug Cap 81 - Receptacle Cap SHELL SIZE 8 THRU 24 TERMINATION STYLE C -Sash Chain N - Sash Chain with Ring NOTE: F or MS version and additional finishes see PV catalog. H+.500 (12.7) -.250 (6.35) CHAIN LENGHT H L Max. M +.031 (.79) -.000 (.00) N Min. Q Max. R Max .719 (18.26) 3.000 (76.20) .562 (14.27) .368 (9.35) .578 (14.68) .734 (18.64) .562 (14.27) .844 (21.44) 3.000 (76.20) .562 (14.27) .368 (9.35) .703 (17.86) .859 (21.82) .562 (14.27) .748 (19.00) 1.000 (25.40) 3.500 (88.90) .562 (14.27) .368 (9.35) .891 (22.63) 1.000 (25.40) .562 (14.27) 14 .873 (22.17) 1.125 (28.58) 3.500 (88.90) .562 (14.27) .368 (9.35) 1.016 (25.81) 1.025 (28.58) .562 (14.27) 16 .998 (25.35) 1.250 (31.75) 3.500 (88.90) .562 (14.27) .368 (9.35) 1.141 (28.98) 1.250 (31.75) .562 (14.27) 18 1.123 (28.52) 1.375 (34.93) 3.500 (88.90) .562 (14.27) .368 (9.35) 1.266 (32.16) 1.375 (34.93) .562 (14.27) 20 1.248 (31.70) 1.500 (38.10) 4.000 (101.60) .625 (15.88) .430 (10.92) 1.391 (35.33) 1.500 (38.10) .562 (14.27) 22 1.373 (34.87) 1.625 (41.26) 4.000 (101.60) .625 (15.88) .430 (10.92) 1.516 (38.51) 1.625 (41.26) .562 (14.27) 24 1.498 (38.05) 1.750 (44.45) 4.000 (101.60) .658 (16.71) .463 (11.76) 1.641 (41.68) 1.750 (44.45) .602 (15.29) Shell Size A ±.003 (.08) F Max. 8 .471 (11.96) 10 .588 (14.94) 12 MATERIALS and FINISHES Protective Cap Sash Chain Ring/Rivet Gasket KPT aluminum alloy, olive drab finish per QQ-P-416 stainless steel stainless steel polychloroprene Dimensions shown in inches (mm) Specifications and dimensions subject to change A-50 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 51 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Receptacles with Printed Circuit Board Contacts How to order KPT 2 E 22 - 36 P W SHELL STYLE CLASS SHELL SIZE CONTACT ARRANGEMENT CONTACT TYPE ALTERNATE INSERT POSITION MODIFICATION CODE SERIES PREFIX KPT -ITT Cannon designation CONTACT ARRANGEMENTS see page A-41 SHELL STYLE ITT Cannon designation 2 -box mounting receptacle (class E only) 7 -jam nut receptacle CONTACT TYPE P -Pin S -Socket ALTERNATE INSERT POSITION W, X, and Z (omit for normal position) CLASS A -general duty (shell type 7 only) E - shell type 2 only MODIFICATION CODE (see following page for description) DV - KPT2 with PC tail contacts .025 ± .001 dia. size 20 .040 ± .001 dia. size 16 EX - KPT2/ KPT7 with PC tail contacts .76 mm dia. size 16 and size 20 EW - KPT2/ KPT7 with PC tail contacts .6mm dia. size 16 and size 20 SHELL SIZES 8, 10, 12, 14, 16, 18, 20, 22, and 24 Note: Consult factory for custom PC Tail configurations Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A Circular SERIES PREFIX • A-51 ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 52 Cannon KPT/KPSE MIL-C-26482 Series I Connectors KPT Connectors with P.C. Tail Contacts KPT2E-PDV Circular A P.C. Tail diameter P.C. tail extension from the rear of the shell flange P.C. contacts to extend .600" ± .032" from rear of shell flange. Contact Size 20 .025 ±.001 Diameter 16 .040 ±.001 Diameter Contact factory for additional requirements. Box Mounting Receptacle – KPT2 EW/EX Shell Size 8 10 12 14 16 18 20 22 24 A +0,03 -0,13 12,00 15,00 19,05 22,23 25,40 28,58 31,75 34,93 38,10 K +0,25 13,50 13,50 13,50 13,50 13,50 13,50 16,50 16,50 17,30 L max. 21,1 21,1 21,1 21,1 21,1 21,1 22,7 22,7 22,7 M ±0,15 11,60 11,60 11,60 11,60 11,60 11,60 14,25 14,25 15,10 N max. 11,10 14,30 17,50 20,60 23,80 27,00 30,20 33,40 36,50 R ±0,15 15,10 18,30 20,60 23,00 24,60 27,00 29,40 31,70 34,90 S max. 21,00 24,20 26,60 29,00 31,30 33,70 36,90 40,10 43,30 ØT ±0,15 3,05 3,05 3,05 3,05 3,05 3,05 3,05 3,05 3,75 Jam Nut Receptacle – KPT7 EW/EX Shell Size* 8 10 12 14 16 18 20 22 24 A +0,03 -0,13 12,00 15,00 19,05 22,23 25,40 28,58 31,75 34,93 38,10 F +0,15 13,3 16,5 20,6 23,8 26,9 30,1 33,3 36,5 39,6 H ±0,15 19,0 22,2 27,0 30,2 33,3 36,5 39,7 42,9 46,0 K ±0,25 3,2 3,2 3,2 3,2 3,2 3,2 4,0 4,0 4,0 M ±0,15 17,7 17,7 17,7 17,7 17,7 17,7 22,5 22,5 23,3 R Thread Type 2 A 9/16-24UNEF 11/16-24UNEF 7/8-20UNEF 1-20UNEF 1-1/8-18UNEF 1-1/4-18UNEF 1-3/8-18UNEF 1-1/2-18UNEF 1-5/8-18UNEF S ±0,5 2,40 2,70 3,20 3,50 3,85 4,15 4,60 4,95 5,25 Panel Thickness min. 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 Y max. 28,0 31,0 36,0 39,0 42,0 45,0 50,0 55,0 57,0 Dimensions shown in inches (mm) Specifications and dimensions subject to change A-52 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 53 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Special Versions with Grounding Continuity These connectors are designed for ensuring continuity. A • At the cable shielding level (to protect it against radio frequency interferences) Circular • At the grounding level (if it is connected to the shielding) The plugs are manufactured with grounding fingers soldered to the front face of the shell. They make contact with the inner side of the receptacle shell. Plug and receptacle feature a special endbell which supports the cable shielding. The connectors are in accordance with the VG 95328 specification. Receptacle with Grounding Continuity (for shielded cable) KPT/KPSE 0E...DZ T D K B C A M L E R S Shell Size A +.003-0.13 B Min. C +0.5 D Max. E 1.00 K ±0.25 L Max. M ±0.15 R ±0.15 S Max. øT ±0.15 †8 .472 (12.00) .360 (6.6) .630 (16.0) .524 (13.3) .590 (15.0) .531 (13.5) 2.047 (52.0) .457 (11.6) .594 (15.1) .827 (21.0) .120 (3.05) 10 .590 (15.00) .362 (9.2) .709 (18.0) .634 (16.1) .590 (15.0) .531 (13.5) 2.047 (52.0) .457 (11.6) .720 (18.3) .953 (24.2) .120 (3.05) 12 .750 (19.05) .480 (12.2) .866 (22.0) .787 (20.0) .669 (17.0) .531 (13.5) 2.440 (62.0) .457 (11.6) .811 (20.6) 1.047 (26.6) .120 (3.05) 14 .875 (22.23) .598 (15.2) .984 (25.0) .874 (22.2) .709 (18.0) .531 (13.5) 2.440 (62.0) .457 (11.6) .905 (23.0) 1.142 (29.0) .120 (3.05) 16 1.00 (25.40) .720 (18.3) 1.102 (28.0) 1.031 (26.2) .709 (18.0) .531 (13.5) 2.440 (62.0) .457 (11.6) .968 (24.6) 1.232 (31.3) .120 (3.05) 18 1.125 (28.58) .787 (20.0) 1.259 (32.0) 1.122 (28.5) .709 (18.0) .531 (13.5) 2.440 (62.0) .457 (11.6) 1.063 (27.0) 1.327 (33.7) .120 (3.05) .120 (3.05) 20 1.25 (31.75) .905 (23.0) 1.338 (34.0) 1.280 (32.5) .709 (18.0) .650 (16.5) 2.440 (62.0) .561 (14.25) 1.157 (29.4) 1.453 (36.9) 22 1.375 (34.93) 1.023 (26.0) 1.50 (38.0) 1.370 (34.8) .709 (18.0) .650 (16.5) 2.440 (62.0) .561 (14.25) 1.248 (31.7) 1.579 (40.1) .120 (3.05) 24 1.50 (38.10) 1.134 (28.8) 1.614 (41.0) 1.492 (37.9) .709 (18.0) .681 (17.3) 2.440 (62.0) .594 (15.1) 1.374 (34.9) 1.705 (43.3) .148 (3.75) † In series KPSE only contact arrangements 8-3A and 8-33 available Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A-53 ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 54 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Cable Conecting Plug with Grounding Continuity (for shielding cable) KPT/KPSE 1E...DZ D K Circular A Y B C A M L Shell Size †8 10 12 14 16 18 20 22 24 A +.003-0.13 .472 (12.00) .590 (15.00) .750 (19.05) .875 (22.23) 1.00 (25.40) 1.125 (28.58) 1.25 (31.75) 1.375 (34.93) 1.50 (38.10) B Min. .360 (6.6) .362 (9.2) .480 (12.2) .598 (15.2) .720 (18.3) .787 (20.0) .905 (23.0) 1.023 (26.0) 1.134 (28.8) C +0.50 .630 (16.0) .709 (18.0) .866 (22.0) .984 (25.0) 1.102 (28.0) 1.259 (32.0) 1.338 (34.0) 1.50 (38.0) 1.614 (41.0) D Max. .524 (13.3) .634 (16.1) .787 (20.0) .874 (22.2) 1.031 (26.2) 1.122 (28.5) 1.280 (32.5) 1.370 (34.8) 1.492 (37.9) E ±1.0 .590 (15.0) .590 (15.0) .669 (17.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) K ±0.25 .531 (13.5) .531 (13.5) .531 (13.5) .531 (13.5) .531 (13.5) .531 (13.5) .650 (16.5) .650 (16.5) .681 (17.3) E L Max. 2.047 (52.0) 2.047 (52.0) 2.440 (62.0) 2.440 (62.0) 2.440 (62.0) 2.440 (62.0) 2.440 (62.0) 2.440 (62.0) 2.440 (62.0) S M ±0.15 .457 (11.6) .457 (11.6) .457 (11.6) .457 (11.6) .457 (11.6) .457 (11.6) .561 (14.25) .561 (14.25) .594 (15.1) S Max. .728 (18.5) .905 (23.0) 1.142 (29.0) 1.161 (29.5) 1.126 (32.0) 1.378 (35.0) 1.516 (38.5) 1.653 (42.0) 1.811 (46.0) øY Max. .827 (21.0) .953 (24.2) 1.047 (26.6) 1.142 (29.0) 1.232 (31.3) 1.327 (33.7) 1.453 (36.9) 1.579 (40.1) 1.705 (43.3) † In series KPSE only contact arrangements 8-3A and 8-33 available Straight Plug with Grounding Continuity KPT/KPSE 6E...DZ A B C E S L Shell Size †8 10 12 14 16 18 20 22 24 A Min. .360 (6.6) .362 (9.2) .480 (12.2) .598 (15.2) .720 (18.3) .787 (20.0) .905 (23.0) 1.023 (26.0) 1.133 (28.8) B +0.50 .630 (16.0) .709 (18.0) .866 (22.0) .984 (25.0) 1.102 (28.0) 1.260 (32.0) 1.340 (34.0) 1.50 (38.0) 1.614 (41.0) C Max. .752 (19.1) .866 (22.0) 1.031 (26.2) 1.157 (29.4) 1.291 (32.8) 1.394 (35.4) 1.535 (39.0) 1.657 (42.1) 1.779 (45.2) D Max. (20.0) (15.0) (26.0) (30.0) (33.0) (36.0) (40.0) (43.0) (46.0) E ±1.0 .590 (15.0) .590 (15.0) .669 (17.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) D L Max. 1.890 (48.0) 1.890 (48.0) 1.890 (48.0) 1.929 (49.0) 1.929 (49.0) 1.929 (49.0) 2.087 (53.0) 2.087 (53.0) 2.087 (53.0) S ±0.2 .669 (17.0) .748 (19.0) .905 (23.0) 1.024 (26.0) 1.142 (29.0) 1.299 (33.0) 1.378 (35.0) 1.535 (39.0) 1.653 (42.0) † In series KPSE only contact arrangements 8-3A and 8-33 available Dimensions shown in inches (mm) Specifications and dimensions subject to change A-54 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 55 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Jam Nut Receptacle with Grounding Continuity (for shielded cable) KPT/KPSE 7E...DZ A D L Shell Size †8 10 12 14 16 18 20 22 24 øA Min. .360 (6.6) .362 (9.2) .480 (12.2) .598 (15.2) .720 (18.3) .787 (20.0) .905 (23.0) 1.023 (26.0) 1.133 (28.8) øB +0.5 .630 (16.0) .709 (18.0) .866 (22.0) .984 (25.0) 1.102 (28.0) 1.260 (32.0) 1.340 (34.0) 1.50 (38.0) 1.614 (41.0) øC Max. .716 (18.2) .842 (21.4) .968 (24.6) 1.094 (27.8) 1.216 (30.9) 1.342 (34.1) 1.50 (38.1) 1.626 (41.3) 1.748 (44.4) D Max. .524 (13.3) .634 (16.1) .787 (20.0) .874 (22.2) 1.031 (26.2) 1.222 (28.5) 1.279 (32.5) 1.370 (34.8) 1.492 (37.9) S E E 1.0 .590 (15.0) .590 (15.0) .669 (17.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) .709 (18.0) L L Max. 1.850 (47.0) 1.850 (47.0) 1.929 (49.0) 1.968 (50.0) 1.968 (50.0) 1.968 (50.0) 2.165 (55.0) 2.165 (55.0) 2.165 (55.0) † In series KPSE only contact arrangements 8-3A and 8-33 available Wiring Instructions KPT/KPSE ...DZ Fixing of shielding braid to connectors with DZ-adapter • Loosen lock nut (5). Slide heat shrink component (6) and lock nut (5) over cable. • Push shielding braid (7) onto endbell (3) and over thread (2). • Fasten shielding braid (7) into rounded groove by means of bailing wire • Fold back protruding shielding braid on cone. • Slide lock nut (5) onto endbell (3). The folded back shielding braid protrudes under the tightened lock nut. • Shrink heat shrink component (6) according to manufacturer’s instructions. (End of heat shrink component to be located in square groove (1)). Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A-55 Circular A B C S ±0.25 .905 (23.0) 1.063 (27.0) 1.248 (31.7) 1.374 (34.9) 1.50 (38.1) 1.626 (41.3) 1.811 (46.0) 1.937 (49.2) 2.059 (52.3) T ±0.25 .748 (19.0) .874 (22.2) 1.063 (27.0) 1.089 (30.2) 1.311 (33.3) 1.437 (36.5) 1.563 (39.7) 1.689 (42.9) 1.811 (46.0) ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 56 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Panel Cutouts Box and Wall Mounting Receptacle A Shell Size P±.005 (013) 4 HOLES Circular FLANGE (FRONT MOUNTING) KPT/KPSE R (T.P.) A +.010 (0.25) -.000 (0.00) Jam Nut Receptacle MOUNTING HOLE DIA. A Dia. R KPT/KPSE P ±.005 Screw †8 .618 (15.70) .594 (15.09) .125 (3.17) #4 10 .735 (16.67) .719 (18.26) .125 (3.17) #4 12 .859 (21.82) .812 (20.62) .125 (3.17) #4 14 .985 (25.02) .906 (23.01) .125 (3.17) #4 16 1.113 (28.27) .969 (24.61) .125 (3.17) #4 18 1.235 (31.37) 1.062 (26.97) .125 (3.17) #4 20 1.361 (34.57) 1.156 (29.36) .125 (3.17) #4 22 1.485 (37.72) 1.250 (31.75) .125 (3.17) #4 24 1.611 (40.92) 1.375 (34.92) .155 (3.94) #6 † Not available in KPSE connectors. Shell Size †8 10 12 14 16 18 20 22 24 B +.000 (0.00) -.010 (0.25) A +.010 (0.25) -.000 (0.00) KPT/KPSE B .540 (13.72) .665 (16.89) .828 (21.02) .952 (24.18) 1.076 (27.33) 1.201 (30.51) 1.326 (33.68) 1.451 (36.86) 1.576 (40.03) A .578 (14.68) .703 (17.86) .890 (22.61) 1.015 (25.78) 1.140 (28.96) 1.265 (32.13) 1.390 (35.31) 1.515 (38.48) 1.640 (41.66) † Not available in KPSE connectors. Panel Thickness Wall Mounting and Box Mounting Receptacle Maximum panel thickness dimensions allowable to ensure complete connector operation for the the Wall Mounting Receptacle, Box Mounting Receptacle, and Thru-Bulkhead Receptacle. Thru-Bulkhead Receptacle B B B B PANEL PANEL PANEL PANEL REAR PANEL MTG REF FRONT PANEL MTG REF Size 8 10 12 14 16 18 20 22 24 FRONT PANEL MTG REF B Max. Size 8 10 12 14 16 18 20 22 24 .087 (2.21) .212 (5.38) REAR PANEL MTG REF B Max. panel and screw head .218 (5.54) .334 (8.74) .311 (7.90) Dimensions shown in inches (mm) Specifications and dimensions subject to change A-56 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 57 Cannon KPT/KPSE MIL-C-26482 Series I Connectors MIL-C-26482 Specifications The following excerpts are some of the paremeter requirements of the MIL-C-26482 specification. Paragraph Reference Contact Retention 4.6.32.1 After preloading to 3 pounds maximum, the force shall be applied at a rate of approximately 1 pound per second and maintained at full load for 5-10 seconds.. No damage to contacts or insert shall result nor shall the contacts be dislocated from their normal position in the connector more that 0.012 inch under giveload for KPSE and within 1 minute after the load is removed for KPT. Contact Size Load in Pounds Min. Load in KG Min. Contact Insertion/Extraction (KPSE only) Coupling Torque A Requirements 20 15 6.8 16 25 11.3 12 25 11.3 4.6.11 When using the proper insertion and extraction tools the forces required to insert or extract the contact shall not exceed 20 Lbs. Connectors shall be less endbell. 4.6.3 For qualification testing, mating halves shall be coupled and uncoupled, measuring the torques necessary. The torques required to couple and uncouple mating connectors halves shall fall within the limits specified as follows: Torque in lb (NM) Shell Size Max Min. 8 8 (.90) 1 (.11) 10 12 (1.36) 1 (.11) 12 16 (1.81) 2 (.23) 14 20 (2.26) 4 (.45) 16 24 (2.71) 4 (.45) Shell Size 18 20 22 24 Torque in lb. (NM) Max Min 28 (3.16) 4 (.45) 32 (3.62) 6 (.68) 36 (4.07) 7 (.79) 44 (4.97) 7 (.79) Durability 4.6.17 Connector halves shall be mated and unmated 500 times at a rate of 200 ± 100 cycles per hour. The test may be performed by hand or by mechanical means, but the coupling ring shall be operated as in normal service. Failure to complete this test because of mechanical malfunction shall be cause for rejection. Insert Retention 4.6.29 Connectors with the endbells and gromments (if possible) removed shall be subjected to a 75 psi load on the insulator in both directions. The load shall be applied at a rate of 10lb/sec. and held for 5 to 10 secs. Insulators shall not be dislodged from their original position. Insulation Resistance 4.6.7.1 On unmated connectors at 25ºC ±3ºC a potential of 500 VDC ±10% shall be applied between all, but not more than 6, pairs of adjacent contacts and between all, but not more than 6, contacts and the shell. Failure to meet a minimum requirement of 5,000 megohms shall be cause for rejection. Vibration 4.6.21 Wired, mated connectors shall be subjected to the vibration test of MIL-STD-1344, Method 205, Test Condition II. Receptacles shall be mounted on the vibration fixture by normal means. All contacts shall be wired in a series circuit and 100 max. milliamperes of current shall be allowed to flow through the series circuit during vibration. Suitable means shall be employed to monitor the current flow and to indicate any discontinuity of more than 10 microseconds. The wire bundle shall be clamped to nonvibrating points at least 8 inches from the rear of the connector. Current discontinuity of 10 microsecond or more, disengagement of the mated connectors, evidence of cracking, breaking, or loosening of parts shall be cause for rejection. Shock 4.6.23 Wired, mated connectors shall be subject to one shock in each direction in each of three mutually perpendicular axes. The pulse shall be approximate half sine wave of 50g±15% magnitude with a duration of 11 ± 1 milliseconds. Receptacles shall be mounted on a shock fixture by normal means. All contacts shall be wired in a series circuit and 90-110 ma. of current shall flow through the series circuit during shock. Suitable means shall be employed to monitor the current flow and to indicate any discontinuity of more than 10 microseconds. Current discontinuity of 10 microseconds or more, disengagement of the mated connectors, evidence of cracking, breaking, or loosening of parts shall be cause for rejection. Thermal Shock 4.6.12 Wired, unmated plug and receptacle shall be subjected to 5 cycles of hot and cold temperatures. Maximum temperature shall be +125ºC and the minimum shall be -55ºC. The temperature extreme shall be 1/2 hour minimum. Cracking, breaking or loosening of parts shall be cause for rejection. Humidity 4.6.25 The connectors shall be subjected to varying humididity, 50% to 95%, conditions for a period of 10 days KRSE or 20 days KPT. The insulation resistance shall not be less than 100 megohms. Air Leakage (KPT Only) 4.6.15.1 A 30 psi pressure differential shall be applied across the connector for 30 minutes. The leak rate, in either direction, shall be no greater than 1 atmosphere cubic inch per hour (4,55 X 10 -3 cm3/S) at -67ºF (-55ºC). Salt Spray (Corrosion) 4.6.19 Unmated and wired connectors shall be subject to a salt fog for 48 hours. These shall be no exposure of base metal, the connector shall be functional and meet the contact resistance requirement. Fluid Immersion 4.6.27 At least one connector, unmated and wired, shall he immersed in each fluid for a period of 20 hours then dried for an hour. Connectors shall be able to make and meet the coupling torque requirements. a) Hydraulic Fluid per MIL-H-5606, b) Lubricating Oil per MIL-L-7808 Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A-57 Circular Test Description ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 58 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Tooling Crimp M22520/1-01 CRINP TOOL M22520/01-02 Turret Circular A CBT-520/530 Tooling Insertion/Extraction 20 16 KPSE Insertion KPSE Extraction Contact Size MS24256A20 MS24256A16 20 16 Contact Size MS24256R20 MS24256R16 Contacts #20 Contact Size/Type Military Part Number 1st Color Bands 2nd 3rd ITT Cannon Part Number 20 Socket 20 Pin 16 Socket 16 Pin M39029/32-259 M39029/31-240 M39029/32-247 M39029/31-228 Red Red Red Red Green Yellow Yellow Red White Black Violet Grey 980-0008-992 030-9036-000 031-9095-003 030-9032-003 Wire Hole Fillers/Grommets Sealing Plugs Contact Size Part Number Cannon Military Color Code 20 16 225-1012-000 225-1011-000 MS3187A20 MS3187-16 Red Blue Dimensions shown in inches (mm) Specifications and dimensions subject to change A-58 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 59 Cannon KPT/KPSE MIL-C-26482 Series I Connectors KPSE Assembly Instructions A Wire Size Size 20 AWG #20-#24 mm2 .5 - .2 Insulation 3/16” mm 4.76 16 #16-#20 1.3 - .5 1/4” 6.35 Strip CRIMPING CONTACTS 1. Strip wires according to the table above taking care not to cut or nick strands. 2. Inserts stripped wire into contact crimp pot. Wire must be visible thru inspection hole. 3. Using correct tool and locator select proper crimp setting for wire sizer to be crimped; cycle the tool once to be sure the indentors are open. Insert contact and wire into locator. Squeeze tool handles firmly and completely to insure a proper crimp. The tool will not release unless the crimp indentors in the tool head have been fully actuated. Release crimped contact and wire from tool. Be certain the wire is visible thru inspection hole in contact. CAUTION: Check that none of the contacts are bent or damaged in any way after crimping. CONTACT INSERTION 1. Remove hardware from plug and receptacle. Slide hardware overwire bundle in proper order for reassembly. 2. Use the proper contact insertion tool and slide the tool over the terminal end of the contact. The size 16 contact lies in the tool and the tool tip butts against the contact shoulder. The rear, or insulation support of the size 20 contact butts against an internal shoulder in the tool tip. NOTE: Apply a small amount of isopropl alcohol to the insertion tool tip while installing contacts. 3. Beginning from center cavity and working outwards in a circular pattern, insert wired contacts into rear of connector by hand untill the front of the contact shoulder is no more than 1/8” from the grommet. Holding the connector horizontally, position tool behind contact. Push tool straight into contact cavity untill contact snaps into position. A light pull on wire will assure that contact is locked securely. Repeat for remaining contacts. Size 8, 10, 12 and 14 16 and18 20, 22 and 24 Torque in-lb (NM) 10-15 (1.23-1.69) 15-25 (1.69-2.82) 25-35 (2.82-3.95) 2. Using mating connector with contacts installed, mate both connector halves together. 4. Use contacts and grommet sealing plugs to fill any empty cavities. COMPLETION 4. Check face of plug or receptacle for proper contact installation. 3. Assemble Ferrule over the grommet by hand as far as possible. 4. Assemble endbell over ferrule and loosely tighten endbell. Partially loosen (1/4 turn) and retighten to recommended torque limits. 2nd Index Line Socket Contacts 1st Index Line Pin Contacts CONTACT EXTRACTION 1. Slide hardware back over wire bundle. Using proper extraction tool or extraction end of proper insertion/extraction tool, proceed as follows: KPSE: There are two lines on the clip sleeve which are vital to the removal process. The first index line is used for removing pin contacts while the second index line is for removing socket contacts. Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A-59 Carefully place the tool tip over the contact to be extracted until the tool tip touches the insulator face. Carefully rotate the tool until the index line is slightly below the insulator face. Keep an even pressure against the tool body; push plunger forward with thumb and index finger, and push the contact out through the clip. Carefully remove extraction tool from connector. Pull wire by hand to complete the removal of the contact. Circular Contact ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 60 Cannon KPT/KPSE MIL-C-26482 Series I Connectors How to Order - Special Termination Connectors KPT KPT KPT KPSE KPSE KPSE Circular A 03 04 05 03 04 05 - 18 18 18 18 18 18 - 32 32 32 32 32 32 P P P P P P W W W W W W PREFIX SHELL STYLE DASH (No Class required, less rear termination) SHELL SIZE CONTACT ARRANGEMENT CONTACT TYPE P - PIN S - Socket ALTERNATE INSERT POSITION Contact ITT Cannon for additional Information Solder Type KPT03/04/05 - Supplied less endball, ferrule and grommet. KPT03 KPT04 KPT05 Crimp Type KPSE03/04/05 - Supplied less endball, ferrule. KPSE03 KPSE04 KPSE05 KPT KPSE Twist Pull Lanyard Release Coupler Plug KPT06/KPSE06 6 6 A E 22 - 55 22 - 55 P S W Z 16 16 PREFIX SHELL STYLE SERVICE TYPE SHELL SIZE CONTACT ARRANGEMENT CONTACT TYPE POLARIZATION MODIFICATION CODE* *Omit (0) of shell style indication when using this modification code. 16 = Overall length of connector including lanyard to be 6.0 (152.40) +_ .125 (3.18) when measured over a 1.0 (25.40) +_ .005 (0.13) diameter mandrel. Dimensions shown in inches (mm) Specifications and dimensions subject to change A-60 www.ittcannon.com ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 61 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Cross Reference List KPT/MIL-C-26482, VG 95328 KPT06J*-*** KPT06P*-*** KPT6A*-***88 KPT6E*-***DN KPT6E*-***DZ KPT02E*-*** KPT07A*-*** KPT07E*-*** KPT07F*-*** KPT08E*-*** KPT08F*-*** KPT08P*-*** KPT7E*-***DN KPTB*-*** Part No. MIL-26482 Part No. VG 95328 MS3110E*-*** MS3110F*-*** MS3110J*-*** MS3110P*-*** MS3111E*-*** MS3111F*-*** MS3111J*-*** MS3111P*-*** MS3116E*-*** MS3116F*-*** MS3116J*-*** MS3116P*-*** MS3112E*-*** H*-***VG 95328 MS3114E*-*** MS3114F*-*** MS3119E*-*** Cross Reference List List Protective Caps Part No. ITT Cannon KPT80 KPT80...C KPT81 KPT81...C KPT81...N Part No. MIL-26482 MS 3180 MS 3180...C MS 3181 MS 3181...C MS 3181...N Part No. VG 95328 Z 2...VG 95328 Z 1...VG 95328 Dimensions shown in inches (mm) Specifications and dimensions subject to change www.ittcannon.com A Circular Part No. KPT ITT Cannon KPT00B*-*** KPT00B*-*** KPT00E*-*** KPT00F*-*** KPT00G*-*** KPT00J*-*** KPT00P*-*** KPT0E*-***DN KPT0E*-***DZ KPT01A*-*** KPT01B*-*** KPT01E*-*** KPT01F*-*** KPT01G*-*** KPT01J*-*** KPT01P*-*** KPT1E*-***DN KPT06A*-*** KPT06B*-*** KPT06E*-*** KPT06F*-*** KPT06G*-*** KPT1E*-***DZ A-61 ca_A1-A163.qxd:Layout 1 2/9/11 7:49 PM Page 62 Cannon KPT/KPSE MIL-C-26482 Series I Connectors Cross Reference List KPSE/MIL-C-26482, VG 95328 Circular A Part No. KPSE ITT Cannon KPSE00A*-*** KPSE00B*-*** KPSE00E*-*** KPSE00F*-*** KPSE0E*-***DZ KPSE00J*-*** KPSE00P*-*** KPSE0E*-***DN KPSE00G*-*** KPSE01A*-*** KPSE01B*-*** KPSE01E*-*** KPSE01F*-*** KPSE01G*-*** KPSE01J*-*** KPSE01P*-*** KPSE*-***DN KPSE02E*-*** KPSE06A*-*** KPSE06B*-*** KPSE06E*-*** KPSE06F*-*** KPSE06G*-*** KPSE06J*-*** KPSE06P*-*** KPSE6A*-***88 KPSE6E*-***88 KPSE6E*-***DN KPSE6E*-***DZ KPSE07A*-*** KPSE1E*-***DZ KPSE7E*-***DN KPSE07E*-*** KPSE07F*-*** KPSE08E*-*** KPSE08F*-*** KPSE08P*-*** KPSE7E*-***DZ Part No. MIL-C-26482 Part No. VG 95328 MS3120E*-*** MS3120F*-*** A*-***VG 95328 B*-***VG 95328 R*-***VG 95328 MS3120P*-*** 25101RA*-***50 MS3121E*-*** MS3121F*-*** MS3121P*-*** MS3122E*-*** C*-***VG 95328 MS3126E*-*** MS3126F*-*** K*-***VG 95328 MS3126P*-*** N*-***VG 95328 J*-***VG 95328 M*-***VG 95328 S*-***VG 95328 D*-***VG 95328 E*-***VG 95328 MS3124E*-*** MS3124F*-*** T*-***VG 95328 Dimensions shown in inches (mm) Specifications and dimensions subject to change A-62 www.ittcannon.com