PCH420V-M12-HZ

HART-enabled vibration transmitter PCH420V series The PCH420V series sensors are velocity transmitters with 4-20 mA outputs and the added capability of digital communications using HART protocol. The HART functionality allows user configuration of the sensors, enables multi-drop cable installations and allows the sensor to communicate directly with a HART-enabled DCS or PLC. The benefits are a sensor that can be configured by the user for a number of different full-scale ranges and filter settings, a reduction in the required cabling, and simple connection to existing plant infrastructure. Digital sensors allow improved connectivity into plant networks, improving efficiency and simplifying decision-making about machinery health. Device variables: PV - Vibration band 1 SV - Vibration band 2 TV - Vibration band 3 Key features • 4-20 mA + HART 7.0 output • Three user-configurable bands • Single or multi-drop loop installation • Hazardous area certified models available Model Description PCH420V-R6(-HZ) 4-20 mA + HART velocity sensor with 2 pin MIL-C-5015 connector PCH420V-M12(-HZ) 4-20 mA + HART velocity sensor with 4 pin M12 connector Note: Model numbers ending in -HZ are hazardous area certified sensors. Certifications • Remote configuration and diagnostics • Connector options: 2 pin MIL-C-5015 (-R6 models) or M12 (-M12 models) • Continuous asset monitoring -HZ models only: (all models) Class I, Div 2 Groups A, B, C, D Class I, Zone 2 AEx/Ex nA nC IIC T4 Tamb: -40°C to +105°C II 3 G Ex nA nC IIC T4 Gc Ta = -40°C to +105°C • Manufactured in an approved ISO 9001 facility The cable installed must be suitable for the installation temperature and the voltage of any intermingled circuits. • Connected cable must be of a type suitable for Zone 2 Hazardous Locations. • The connected cable and connector must provide a minimum ingress protection level of IP54, when assessed according to EN 60079-0 and EN 60079-15. Unused connector must be fitted with an appropriately rated blanking cover. • The connection must be made in a manner that cannot be separated without the use of a tool. • Where the installation requires that the Accelerometer enclosure be grounded, this is to be done using a metal mounting stud as described in document 13327-01, 13334-01, 13335-01 or 13336-01. Note: Due to continuous process improvement, specifications are subject to change without notice. This document is cleared for public release. Wilcoxon Sensing Technologies An Amphenol Company 99249 Rev.F.1 02/19 8435 Progress Drive Frederick, MD 21701 USA Tel: +1 (301) 330-8811 Fax: +1 (301) 330-8873 info@wilcoxon.com buy.wilcoxon.com www.wilcoxon.com 1 HART-enabled vibration transmitter PCH420V series M12 4 PIN CONNECTOR SPECIFICATIONS HART PARAMETERS Full scale velocity output, 20 mA, ± 10% Programmable PV band 0.5 - 5.0 in/sec, peak (12.7 - 127 mm/sec, peak) HART analysis bands, independently programmable: PV, SV, TV low-pass high-pass band-pass (max 2, simultaneous) Signal detection options RMS, peak, true peak Minimum analysis bandwidth 10 Hz 2.52  [ 64.0 mm ] .97  [ 24.6 mm ] SENSOR SPECIFICATIONS Frequency response: .75  [ 19.1 mm ] ± 10%  ± 3 dB Measurement accuracy at 25°C, 100 Hz, 1 ips full scale 10 Hz - 1 kHz 3.0 Hz - 1.95 kHz 1/4-28 MOUNTING HOLE Connections - PCH420V-M12 Function Connector pin loop positive 1 loop negative 2 N/C 3 N/C 4 ground shell ± 5% Power requirements, 2-wire loop power: Voltage, between pins A and B 12 - 30 VDC Current draw 3.8 - 22 mA Loop resistance at 24 VDC, max 600 Ω Turn on time, 4-20 mA loop 30 seconds Grounding case isolated, internally shielded Temperature range –40° to +105° C (–40° to +221°F) Vibration limit 500 g peak Shock limit 5,000 g peak Sealing hermetic Sensing element design PZT, shear Case material 316L stainless steel Mounting 1/4-28 tapped hole 1 .86  [ 21.8 mm ] -R6 models Mating connector 4 pin, M12   2 pin, MIL-C-5015 Recommended cabling J9T4A J9T2A Recommended connector R75S R6H series .97  [ 24.6 mm ] .75  [ 19.1 mm ] Notes: 1 Maximum loop resistance (RL) can be calculated by: VDC power – 10.3 V MIL-C-5015 2 PIN CONNECTOR 2.75  [ 69.9 mm ] -M12 models RL = .86  [ 21.8 mm ] 1/4-28 MOUNTING HOLE M12 connector 22.8 mA HART communication requires min. 250Ω resistance. R6 connector Connections - PCH420V-R6 Function Connector pin loop positive A loop negative B ground shell Note: Due to continuous process improvement, specifications are subject to change without notice. This document is cleared for public release. Wilcoxon Sensing Technologies An Amphenol Company 99249 Rev.F.1 02/19 8435 Progress Drive Frederick, MD 21701 USA Tel: +1 (301) 330-8811 Fax: +1 (301) 330-8873 info@wilcoxon.com buy.wilcoxon.com www.wilcoxon.com 2