PT10LV10-253A2020-PM-S

Enabling the Electronics Revolution PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer The PT-10 and PTC-10 potentiometers offer control where frequent adjustment is required. The shaftless design allows for employment of different engagement mechanisms, such as a customized shaft, a motor control or a human interface adjustment. This potentiometer can also control variable outputs including frequency, change in motor speed or volume. KEY FEATURES IP54 Up to 16 detents Up to 100k Extra-long life Flame retardant ▶Excellent performance (up to 3% linearity) ▶Carbon or cermet resistive element ▶Up to 16 mechanical detents for tactile feedback ▶Up to 100.000 life cycles ▶IP54 protection ▶Magazine packaging for automatic insertion available ▶Polyester / Alumina substrate ▶Wiper positioned at initial, 50% or fully clockwise ▶Loose and assembled shaft and knobs ▶Linear, logarithmic and antilogarithmic tapers ▶Self extinguishable plastic (UL 94V-0) available ▶SPDT switch and low torque version available On request ▶Embossed tape packaging APPLICATIONS ELECTRICAL SPECIFICATIONS PT-10 PTC-10 Taper¹ Lin, Log, Alog Range of values¹ Lin Log, Alog Tolerance¹ 100Ω ≤ Rn ≤ 1MΩ 1MΩ < Rn ≤ 5MΩ Max. Voltage Lin Log, Alog Nominal power Lin Log, Alog (Decad. 1.0 - 2.0 - 2.2 - 2.5 - 4.7 - 5.0) 100Ω ≤ Rn ≤ 5MΩ 1KΩ ≤ Rn ≤ 5MΩ Residual resistance¹ ≤ 0.5% Rn (5Ω min.) Equivalent noise resistance ≤ 3% Rn (3Ω min.) Operating temperature -25°C to +70°C ² (-13°F to + 158°F) ± 20% ± 30% 200 VDC 100 VDC 50°C (122°F) 0.15 W 0.07 W ▶Appliance program selection ▶Thermostat adjustment ▶Timer and control relays ▶Consumer electronics ▶Power tool controls ▶Test and measurement equipment 70°C (158°F) 0.33 W 0.17 W -40°C to +90°C ³ (-40°F to + 194°F) 1 Others available on request; 2 Up to 85°C depending on application.; 3 +120°C/+248°F upon request Page 1 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer MECHANICAL SPECIFICATIONS PT-10 PTC-10 Mechanical rotation angle¹ 235° ± 5° Electrical rotation angle¹ 220° ± 20° Torque Rotational Stop 0.4 to 2 Ncm (0.6 to 2.7 in-oz) > 5 Ncm (>7 in-oz) Push-pull force over the rotor > 49N Life² Up to 100k cycles Up to 10k cycles 1 Endless rotation available: ST-10; 2 Others check availability ENVIRONMENTAL TESTING Test method (CEI 393-1) PT-10 ΔR(%)- Piher typical test results PTC-10 ΔR(%) - Piher typical test results Electrical life 1.000h at 50°C; 0.15W 1.000h at 70°C; 0.33W ±5% n/a n/a ±2% Mechanical life 1000 cycles at 10 to 15 cpm ±3 % (Rn < 1M ) ±2% Temperature coefficient –25°C; +70°C -40°C; +90°C ±300 ppm/°C (Rn < 100K) n/a n/a ±100 ppm/°C Thermal cycling 16h at 85°C and 2h at -25°C 16h at 90°C and 2h at -40°C ±2.5% n/a n/a ±2% Damp heat 500h at 40°C and 95% relative humidity (RH) ±5% ±2% Vibration 2h each plane at 10Hz - 55Hz ±2% ±2% Storage 6 month at 23°C ±2°C and 50% RH ±2.5% ±2% Out of range values may not comply with these results. Standard test conditions: temperature:23°C ±2°C and 45% to 70% RH RECOMMENDED CONNECTIONS Recommended connection circuit for a position sensor or control application (voltage divider circuit electronic design). VCC E S R A AD RL C RL ≈100 x R POWER RATING CURVE PT-10 PTC-10 W (%) W (%) 100 % 100 % 40 % 40 % 50°C 70°C 70 90 C Page 2 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer HOW TO ORDER Carbon potentiometer (Example: PT10LH01-101A2020-S) Optional features PT10 _ Mounting method2 Series Rotors1 B G K L M R W X Y Z - ___ inserted shaft H01 H04 H05 H07 H02 H10 V05 V10 V11 V13 horizontal adjust crimped terminals ____ - ___ - ___ - ___ _ Ω-Value3 Taper Cut track 101 = 100Ω 201 = 200Ω … 504 = 500KΩ 505 = 5MΩ 000 = CM A = lin. B = log. C = alog. [empty] PCI PCF vertical adjust crimped terminals inserted knob _ Tolerance4 Life 0505 = ±5% 0707 = ±7% 1010 = ±10% 2020 = ±20% 3030 = ±30% XXYY = +XX-YY% [empty] = 1K cycles E = 10K cycles - _ _ - Detents Shaft/Knob [empty] PAI PAM PAF P1I P1F P02 … P16 [empty] = none 1 = Fig.1 2 = Fig.2 … 18 = Fig.18 _ Flammability6 [empty] = standard I = non-flammable Packaging5 - __ - __ Shaft/Rotor color7 [empty] AM = yellow AZ = blue BL = white CR = cream GR = grey MA = brown NA = orange NE = black RO = red VE = green VI = violet [empty] = bulk T = magazines _ - S Torque [empty] = standard L = ≤ 1 Ncm Wiper position [empty] = initial PM = 50% PF = final Cermet potentiometer (Example: PTC10LH01-101A2020) PTC10 _ ___ Series Rotors1 Mounting method2 B G K L M R W X Y Z H01 H04 H05 H02 H10 V05 V10 V11 V13 inserted shaft inserted knob - horizontal adjust crimped terminals vertical adjust - ___ Optional features - _ - _ - __ - ___ _ ____ Ω-Value3 Taper Tolerance4 Detents Packaging5 101 = 100Ω 201 = 200Ω … 504 = 500KΩ 505 = 5MΩ 000 = CM A = lin. B = log. C = alog. 0505 = ±5% 0707 = ±7% 1010 = ±10% 2020 = ±20% 3030 = ±30% XXYY = +XX-YY% [empty] PAI PAM PAF P1I P1F P02 … P16 [empty] = bulk T = magazines _ crimped terminals Life [empty] = 1K cycles E = 10K cycles Shaft/Knob [empty] = none 1 = Fig.1 2 = Fig.2 … 18 = Fig.18 __ - Shaft/Rotor color7 Wiper position [empty] AM = yellow AZ = blue BL = white CR = cream GR = grey MA = brown NA = orange NE = black RO = red VE = green VI = violet [empty] = initial PM = 50% PF = final _ Torque [empty] = standard L = ≤ 1 Ncm 1. Rotors: "Z" adjustment only available on "H"-mounting versions. Rotor "G" only available in purple (shaft/rotor color "VI") 2. Mounting method: V05”, “H07” terminals material: brass. 3. Ω- Value: XXX - First two digits of Ω-value 000 = CM = switch SPDT version XXX - Number of zeros 45° 4. Tolerance: for custom tolerance please check availability: info@piher.net 5. Packaging: available options depend on mounting method, see “available packaging option” below. Embossed tape packaging on request. 6. Non-flammable according to UL 94V-0: housing, rotor and shaft. PTC-10 made of non-flammable material by standard. 7. Without knob or shaft: only the rotor. With knob or shaft: only the knob/shaft. ORDER CODE EXAMPLES PT10LH01-103A2020-S 10mm carbon potentiometer with rotor “L” (arrow shape), H01 mounting method (horizontal adjustment), 10K value, linear taper and 20% resistive tolerance. PTC10WV05-104A1010-9-NE 10mm cermet potentiometer with rotor “W” (pre-inserted shaft), V05 mounting method (vertical adjustment), 100K resistive value, linear taper, 10% resistive tolerance and black shaft. Page 3 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer STANDARD CONFIGURATION PT-10 PTC-10 Life 1.000 cycles Cut track no Detents none Packaging bulk Shaft/thumb wheel none Non-flammability no yes Housing color black cream Rotor color white cream Wiper Position initial Torque 0.4 to 2 Ncm Linearity not controlled n/a ROTORS Without shaft or knob L Screwdriver M Hexagonal With inserted shaft X Adjustable from collector side G Hexagonal K Cross slot R B With inserted knob / thumbwheel W Adjustable from terminal side Y Adjustable from terminal side Z Adjustable from collector side Default knob is Fig. 5 - Ref. 5034 Default knob is Fig. 5 - Ref. 5034 Default delivery is at initial position. Wipers are shown positioned at 50% for the picture. Download the STEP file here: https://piher.net/piher/?p=905 Page 4 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer MOUNTING METHOD Vertical adjust / Horizontal mounting - straight terminals V05 - 5mm V10 -10mm Vertical adjust / Horizontal mounting - crimped terminals V11 - 10mm V13 - 10mm Horizontal adjust / Vertical mounting - straight terminals H01 - 2.5mm H04 - 3.8mm H05 - 5mm H07 - 3.8mm (only PT-10) Horizontal adjust / Vertical mounting - crimped terminals H02 - 2.5mm H10 - 5mm Page 5 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer STANDARD RESISTANCE-VALUES AND TOLERANCES Resistance Ω 100 200 220 250 470 500 1K 2K 2.2K 2.5K 4.7K 5K 10K 20K 22K 25K 47K 50K 100K 200K 220K 250K 470K 500K 1M 2M 2.5M 4.7M 5M Order Code 101 201 221 251 471 501 102 202 222 502 103 205 252 472 Tolerance 203 223 253 473 503 104 204 224 254 474 504 105 20% 255 475 505 30% SWITCH VERSIONS AVAILABLE WITH OR WITHOUT DETENTS Switch standard specification A80 Switch code A80 Switch code 1 CONTACT A Power rating: 24V / 15mA ON position resistance: ≤ 5Ω Insulation resistance: ≥ 30MΩ 0 CONTACT 1 A = Initial S = Wiper E = Final E A S E 0 50 % 45º 45º Mechanical rotation angle: 235º±5º Contact Piher Sensing Systems for ordering information. TAPERS Standard Example: special custom taper 100% Rn C A R 2 ±5% A = Linear B = Log. C = Alog. B For more information on custom tapers contact Piher Sensing Systems. CUT TRACKS (OPEN CIRCUIT DESIGN) rd PCI PCF CCW on-off (A) A E Cut track at the end of travel. Cut track at the beginning of travel. A S E A S CW on-off (E) E A E Other configurations available upon request. Cut Track not available for PTC-10. Page 6 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer DETENTS rd PAM P1i P1F P02 P03 P04 P05 P06 P07 P08 P09 P10 P11 P12 P13 P16 PAI PID PFD PAF Wiper position Wiper position B B A A A = 26º (wiper positioned at initial) B B = 27.5º B (wiper positioned at final) Relative detent positions along total mechanical travel Standard mechanical life is 500 cycles. Long life versions are available upon request and have the following characteristics at Tª: Potentiometers with 1 to 3 detents up to 10K cycles; Potentiometers with 4 and more detents up to 5K cycles Please consult Piher Sensing Systems if unique non-overlapping values at each detent position or LOG/ALOG tapers are required. Different output voltage values can be matched at each detent position (see next section). Detent torque can vary from 1.2 to 2.5 times the standard potentiometer torque. For V05 mounting: check availability. For more than 16 detents versions please contact Piher Sensing Systems. STEPPED OUTPUTS / CONSTANT VALUE ZONES 100% Un IMPROVED REPEATABILITY when the potentiometer’s wiper position is located at detent nº9, the output votage will be 88.9% Un ± % tolerance. 88.9% Un 77.7% Un 5 6 26 4 7 3 55.5% Un ° 66.6% Un 8 9 2 44.4% Un 33.3% Un 1 0º 234º 10 22.2% Un S A 11.1% Un 100% 50% 1 E A 0% Un / 0º A S = = 2 = 3 = 4 = 5 = 6 = 7 = 8 = 9 Wiper position E 10 E Constant value zones can be combined with strategically located mechanical detents to provide exact alignment between the electrical output (flat areas) and the mechanical detent position. This provides clear mechanical positions that are not only repeatable, but perfectly aligned electrical outputs at each of the (detent) angles. The detents also prevent output values from changing due to vibration or accidental rotor movements. The result is a higher level of precision in controlling lighting, temperature, motor or other electronic control systems. Contact Piher Sensing Systems for ordering information. Page 7 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer PACKAGING Bulk Without shaft: 1000 units per box With Thumbweel: 800 units per box With shaft: 400 units per box Dimensions (mm): 185x85x80 Magazine for automatic insertion (50 units) Horizontal adjust 540 +1.5 13.5 540 +1.5 18.9 7.6 Vertical adjust 12 AVAILABLE PACKAGING OPTIONS Mounting Type Terminal Style Mounting Method Bulk Magazine H01 x x H04 x x H05 x x H07 x x H02 x x H10 x V05 x V10 x x V11 x x V13 x Straight Horizontal adjust Crimped Straight Vertical adjust Crimped Rotor Type X, W, Y, Z only in bulk packaging. Embossed tape packaging on request. Page 8 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer SHAFTS, KNOBS AND THUMBWHEELS (TOP VIEW, FOR G AND M ROTOR TYPES) Fig. 1 - Ref. 5016 Fig. 2 - Ref. 5053 Fig. 3 - Ref. 5012 Fig. 4 - Ref. 6053 3 5 5 Fig. 5 - Ref. 5034 8.1 1 2.6 3.7 8.4 34 10.4 Fig. 6 - Ref. 5035 11.5 10 3.1 Fig. 7 - Ref. 5115 Fig. 8 - Ref.: 5116 Fig. 9 - Ref 5119 Fig. 10 - Ref. 5120 4.9 4.9 4.9 4.9 Fig. 16 - Ref. 5039 12 4.5 3.3 15.2 Upon request: Numbered thumbwheel Fig. 17 - Ref. 5062 19 21 1 5 1.5 9.5 Fig. 14 - Ref. 5055 4.9 12.5 25.5 15.2 25.5 Fig. 15 - Ref. 6008 Fig. 12 - Ref. 6052 For R rotor type only Marking: configurable number of positions Example of four positions marking Fig. 18 - Ref: 6064 2-gang plastic knob/shaft 25 Ø6 13 12.75 5 Ø1.3 2.5 5 By default, shafts, knobs and thumbweels are delivered unassembled. If you need the shaft or knob to be delivered assembled from the factory, please select the appropriate rotor in the part number: X, W, Y or Z. On request, shafts, knobs and thumbweels can be delivered at specific positions (drawing must be provided), otherwise they are delivered at random position. The plastic color can be stated in the part number. Non flammable plastic available, if potentiometer is orderer with nonflammable plastic (UL-94V0), the shaft or knob will be delivered with non-flammable plastic. If you wish to use your own plastic shaft/ knob/actuator please contact Piher for advice about compatible materials. Page 9 of 10 www.piher.net PT-10 / PTC-10 10-mm carbon / cermet through-hole potentiometer POSITIONING PM 50% ±15° Default INITIAL PF FINAL Wiper positioning on initial position is standard. Special delivery positions available on request. OUR ADVANTAGE ▶Leading-edge innovative position sensing solutions ▷Contactless (Hall-effect and Inductive Technology) ▷Contacting (Potentiometers, Printed Electronics) ▶Engineering design-in support ▶All our products can be customized to fit target application and customer requirement ▶Capability to move seamlessly from development to true high-volume production ▶A global footprint with global engineering and commercial support ▶One-stop shop not limited to position sensors (temperature, pressure, gas,…) through group collaboration ▶Flexibility and entrepreneurship of a medium-sized company with the backing of Amphenol Corporation CONTACT ISO 14001 Please always use the latest updated datasheets and 3D models published on our website. Disclaimer: The product information in this catalog is for reference purposes. Please consult for the most up to date and accurate design information. Piher Sensors & Controls S.A., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Piher”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product described herein. Piher disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Piher’s terms and conditions of sale, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Piher. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Piher products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Piher for any damages arising or resulting from such use or sale. Please contact authorized Piher personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Information contained in and/or attached to this catalog may be subject to export control regulations of the European Community, USA, or other countries. Each recipient of this document is responsible to ensure that usage and/or transfer of any information contained in this document complies with all relevant export control regulations. If you are in any doubt about the export control restrictions that apply to this information, please contact the sender immediately. For any Piher Exports, Note: All products / technologies are EAR99 Classified commodities. Exports from the United States are in accordance with the Export Administration Regulations. Diversion contrary to US law is prohibited. Rev:28032022 © 2021 Piher Sensors & Controls S.A BUREAU VERITAS Certification Piher Sensing Systems Polígono Industrial Municipal Vial T2, Nº22 31500 Tudela Spain sales@piher.net Europe: +34 948 820 450 Americas: +1 636 251 0855 Asia Pacific: +65 9641 8886 India: +91 9538 686 586 Page 10 of 10 www.piher.net