Enabling the
Electronics
Revolution
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
The PT-10 and PTC-10 potentiometers offer control where frequent adjustment is required. The shaftless
design allows for employment of different engagement mechanisms, such as a customized shaft, a motor
control or a human interface adjustment. This potentiometer can also control variable outputs including
frequency, change in motor speed or volume.
KEY FEATURES
IP54
Up to 16
detents
Up to
100k
Extra-long
life
Flame
retardant
▶Excellent performance (up to 3% linearity)
▶Carbon or cermet resistive element
▶Up to 16 mechanical detents for tactile feedback
▶Up to 100.000 life cycles
▶IP54 protection
▶Magazine packaging for automatic insertion available
▶Polyester / Alumina substrate
▶Wiper positioned at initial, 50% or fully clockwise
▶Loose and assembled shaft and knobs
▶Linear, logarithmic and antilogarithmic tapers
▶Self extinguishable plastic (UL 94V-0) available
▶SPDT switch and low torque version available
On request
▶Embossed tape packaging
APPLICATIONS
ELECTRICAL SPECIFICATIONS
PT-10
PTC-10
Taper¹
Lin, Log, Alog
Range of values¹
Lin
Log, Alog
Tolerance¹
100Ω ≤ Rn ≤ 1MΩ
1MΩ < Rn ≤ 5MΩ
Max. Voltage
Lin
Log, Alog
Nominal power
Lin
Log, Alog
(Decad. 1.0 - 2.0 - 2.2 - 2.5 - 4.7 - 5.0)
100Ω ≤ Rn ≤ 5MΩ
1KΩ ≤ Rn ≤ 5MΩ
Residual resistance¹
≤ 0.5% Rn (5Ω min.)
Equivalent noise
resistance
≤ 3% Rn (3Ω min.)
Operating temperature
-25°C to +70°C ²
(-13°F to + 158°F)
± 20%
± 30%
200 VDC
100 VDC
50°C (122°F)
0.15 W
0.07 W
▶Appliance program selection
▶Thermostat adjustment
▶Timer and control relays
▶Consumer electronics
▶Power tool controls
▶Test and measurement
equipment
70°C (158°F)
0.33 W
0.17 W
-40°C to +90°C ³
(-40°F to + 194°F)
1 Others available on request; 2 Up to 85°C depending on application.; 3 +120°C/+248°F upon request
Page 1 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
MECHANICAL SPECIFICATIONS
PT-10
PTC-10
Mechanical rotation angle¹
235° ± 5°
Electrical rotation angle¹
220° ± 20°
Torque
Rotational
Stop
0.4 to 2 Ncm (0.6 to 2.7 in-oz)
> 5 Ncm (>7 in-oz)
Push-pull force over the rotor
> 49N
Life²
Up to 100k cycles
Up to 10k cycles
1 Endless rotation available: ST-10; 2 Others check availability
ENVIRONMENTAL TESTING
Test method (CEI 393-1)
PT-10
ΔR(%)- Piher typical test results
PTC-10
ΔR(%) - Piher typical test results
Electrical life
1.000h at 50°C; 0.15W
1.000h at 70°C; 0.33W
±5%
n/a
n/a
±2%
Mechanical life
1000 cycles at 10 to 15 cpm
±3 % (Rn < 1M )
±2%
Temperature
coefficient
–25°C; +70°C
-40°C; +90°C
±300 ppm/°C (Rn < 100K)
n/a
n/a
±100 ppm/°C
Thermal cycling
16h at 85°C and 2h at -25°C
16h at 90°C and 2h at -40°C
±2.5%
n/a
n/a
±2%
Damp heat
500h at 40°C and 95% relative
humidity (RH)
±5%
±2%
Vibration
2h each plane at 10Hz - 55Hz
±2%
±2%
Storage
6 month at 23°C ±2°C and 50% RH
±2.5%
±2%
Out of range values may not comply with these results. Standard test conditions: temperature:23°C ±2°C and 45% to 70% RH
RECOMMENDED CONNECTIONS
Recommended connection circuit for a position sensor or control application (voltage divider circuit electronic design).
VCC
E
S
R
A
AD
RL
C
RL ≈100 x R
POWER RATING CURVE
PT-10
PTC-10
W (%)
W (%)
100 %
100 %
40 %
40 %
50°C
70°C
70
90
C
Page 2 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
HOW TO ORDER
Carbon potentiometer (Example: PT10LH01-101A2020-S)
Optional features
PT10
_
Mounting
method2
Series
Rotors1
B
G
K
L
M
R
W
X
Y
Z
-
___
inserted
shaft
H01
H04
H05
H07
H02
H10
V05
V10
V11
V13
horizontal
adjust
crimped
terminals
____
- ___ - ___ -
___
_
Ω-Value3
Taper
Cut
track
101 = 100Ω
201 = 200Ω
…
504 = 500KΩ
505 = 5MΩ
000 = CM
A = lin.
B = log.
C = alog.
[empty]
PCI
PCF
vertical
adjust
crimped
terminals
inserted
knob
_
Tolerance4
Life
0505 = ±5%
0707 = ±7%
1010 = ±10%
2020 = ±20%
3030 = ±30%
XXYY = +XX-YY%
[empty] = 1K cycles
E = 10K cycles
-
_
_
-
Detents
Shaft/Knob
[empty]
PAI
PAM
PAF
P1I
P1F
P02
…
P16
[empty] = none
1 = Fig.1
2 = Fig.2
…
18 = Fig.18
_
Flammability6
[empty] = standard
I = non-flammable
Packaging5
- __ - __ Shaft/Rotor
color7
[empty]
AM = yellow
AZ = blue
BL = white
CR = cream
GR = grey
MA = brown
NA = orange
NE = black
RO = red
VE = green
VI = violet
[empty] = bulk
T = magazines
_
- S
Torque
[empty] = standard
L = ≤ 1 Ncm
Wiper
position
[empty] = initial
PM = 50%
PF = final
Cermet potentiometer (Example: PTC10LH01-101A2020)
PTC10
_
___
Series
Rotors1
Mounting
method2
B
G
K
L
M
R
W
X
Y
Z
H01
H04
H05
H02
H10
V05
V10
V11
V13
inserted
shaft
inserted
knob
-
horizontal
adjust
crimped
terminals
vertical
adjust
- ___
Optional features
- _
- _ - __ -
___
_
____
Ω-Value3
Taper
Tolerance4
Detents
Packaging5
101 = 100Ω
201 = 200Ω
…
504 = 500KΩ
505 = 5MΩ
000 = CM
A = lin.
B = log.
C = alog.
0505 = ±5%
0707 = ±7%
1010 = ±10%
2020 = ±20%
3030 = ±30%
XXYY = +XX-YY%
[empty]
PAI
PAM
PAF
P1I
P1F
P02
…
P16
[empty] = bulk
T = magazines
_
crimped
terminals
Life
[empty] = 1K cycles
E = 10K cycles
Shaft/Knob
[empty] = none
1 = Fig.1
2 = Fig.2
…
18 = Fig.18
__
-
Shaft/Rotor
color7
Wiper
position
[empty]
AM = yellow
AZ = blue
BL = white
CR = cream
GR = grey
MA = brown
NA = orange
NE = black
RO = red
VE = green
VI = violet
[empty] = initial
PM = 50%
PF = final
_
Torque
[empty] = standard
L = ≤ 1 Ncm
1. Rotors: "Z" adjustment only available on "H"-mounting versions. Rotor "G" only available in purple (shaft/rotor color "VI")
2. Mounting method: V05”, “H07” terminals material: brass.
3. Ω- Value: XXX - First two digits of Ω-value
000 = CM = switch SPDT version
XXX - Number of zeros
45°
4. Tolerance: for custom tolerance please check availability: info@piher.net
5. Packaging: available options depend on mounting method, see “available packaging option” below. Embossed tape packaging on request.
6. Non-flammable according to UL 94V-0: housing, rotor and shaft. PTC-10 made of non-flammable material by standard.
7. Without knob or shaft: only the rotor. With knob or shaft: only the knob/shaft.
ORDER CODE EXAMPLES
PT10LH01-103A2020-S
10mm carbon potentiometer with rotor “L” (arrow shape), H01 mounting method (horizontal adjustment), 10K value, linear taper and 20% resistive
tolerance.
PTC10WV05-104A1010-9-NE
10mm cermet potentiometer with rotor “W” (pre-inserted shaft), V05 mounting method (vertical adjustment), 100K resistive value, linear taper,
10% resistive tolerance and black shaft.
Page 3 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
STANDARD CONFIGURATION
PT-10
PTC-10
Life
1.000 cycles
Cut track
no
Detents
none
Packaging
bulk
Shaft/thumb wheel
none
Non-flammability
no
yes
Housing color
black
cream
Rotor color
white
cream
Wiper Position
initial
Torque
0.4 to 2 Ncm
Linearity
not controlled
n/a
ROTORS
Without shaft or knob
L
Screwdriver
M
Hexagonal
With inserted shaft
X
Adjustable from
collector side
G
Hexagonal
K
Cross slot
R
B
With inserted knob / thumbwheel
W
Adjustable from
terminal side
Y
Adjustable from terminal side
Z
Adjustable from collector side
Default knob is Fig. 5 - Ref. 5034
Default knob is Fig. 5 - Ref. 5034
Default delivery is at initial position. Wipers are shown positioned at 50% for the picture.
Download the STEP file here:
https://piher.net/piher/?p=905
Page 4 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
MOUNTING METHOD
Vertical adjust / Horizontal mounting - straight terminals
V05 - 5mm
V10 -10mm
Vertical adjust / Horizontal mounting - crimped terminals
V11 - 10mm
V13 - 10mm
Horizontal adjust / Vertical mounting - straight terminals
H01 - 2.5mm
H04 - 3.8mm
H05 - 5mm
H07 - 3.8mm (only PT-10)
Horizontal adjust / Vertical mounting - crimped terminals
H02 - 2.5mm
H10 - 5mm
Page 5 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
STANDARD RESISTANCE-VALUES AND TOLERANCES
Resistance
Ω
100 200
220
250
470
500
1K
2K
2.2K 2.5K 4.7K
5K
10K 20K 22K 25K 47K 50K 100K 200K 220K 250K 470K 500K 1M
2M 2.5M 4.7M 5M
Order Code
101 201
221
251
471
501
102
202
222
502
103
205
252
472
Tolerance
203
223
253
473
503
104
204
224
254
474
504
105
20%
255
475
505
30%
SWITCH VERSIONS AVAILABLE WITH OR WITHOUT DETENTS
Switch standard specification
A80 Switch code
A80 Switch code
1 CONTACT
A
Power rating: 24V / 15mA
ON position resistance: ≤ 5Ω
Insulation resistance: ≥ 30MΩ
0
CONTACT
1
A = Initial
S = Wiper
E = Final
E
A
S
E
0
50 %
45º
45º
Mechanical rotation angle: 235º±5º
Contact Piher Sensing Systems for ordering information.
TAPERS
Standard
Example: special custom taper
100% Rn
C
A
R 2 ±5%
A = Linear
B = Log.
C = Alog.
B
For more information on custom tapers contact Piher Sensing Systems.
CUT TRACKS (OPEN CIRCUIT DESIGN)
rd
PCI
PCF
CCW on-off (A)
A
E
Cut track at the end
of travel.
Cut track at the beginning
of travel.
A
S
E
A
S
CW on-off (E)
E
A
E
Other configurations available upon request. Cut Track not available for PTC-10.
Page 6 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
DETENTS
rd
PAM
P1i
P1F
P02
P03
P04
P05
P06
P07
P08
P09
P10
P11
P12
P13
P16
PAI
PID
PFD
PAF
Wiper
position
Wiper
position
B
B
A
A
A = 26º
(wiper positioned at initial)
B
B = 27.5º
B
(wiper positioned at final)
Relative detent positions along total mechanical travel
Standard mechanical life is 500 cycles.
Long life versions are available upon request and have the following characteristics at Tª: Potentiometers with 1 to 3 detents up to 10K cycles; Potentiometers with 4 and more
detents up to 5K cycles
Please consult Piher Sensing Systems if unique non-overlapping values at each detent position or LOG/ALOG tapers are required.
Different output voltage values can be matched at each detent position (see next section).
Detent torque can vary from 1.2 to 2.5 times the standard potentiometer torque.
For V05 mounting: check availability.
For more than 16 detents versions please contact Piher Sensing Systems.
STEPPED OUTPUTS / CONSTANT VALUE ZONES
100% Un
IMPROVED REPEATABILITY
when the potentiometer’s wiper position is located at detent
nº9, the output votage will be 88.9% Un ± % tolerance.
88.9% Un
77.7% Un
5
6
26
4
7
3
55.5% Un
°
66.6% Un
8
9
2
44.4% Un
33.3% Un
1
0º
234º 10
22.2% Un
S
A
11.1% Un
100%
50%
1
E
A
0% Un / 0º
A
S
=
=
2
=
3
=
4
=
5
=
6
=
7
=
8
=
9
Wiper position
E
10
E
Constant value zones can be combined
with strategically located mechanical
detents to provide exact alignment
between the electrical output (flat areas)
and the mechanical detent position.
This provides clear mechanical positions
that are not only repeatable, but
perfectly aligned electrical outputs at
each of the (detent) angles. The detents
also prevent output values from
changing due to vibration or accidental
rotor movements.
The result is a higher level of precision
in controlling lighting, temperature,
motor or other electronic control
systems.
Contact Piher Sensing Systems for ordering information.
Page 7 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
PACKAGING
Bulk
Without shaft: 1000 units per box
With Thumbweel: 800 units per box
With shaft: 400 units per box
Dimensions (mm): 185x85x80
Magazine for automatic insertion (50 units)
Horizontal adjust
540 +1.5
13.5
540 +1.5
18.9
7.6
Vertical adjust
12
AVAILABLE PACKAGING OPTIONS
Mounting Type
Terminal Style
Mounting Method
Bulk
Magazine
H01
x
x
H04
x
x
H05
x
x
H07
x
x
H02
x
x
H10
x
V05
x
V10
x
x
V11
x
x
V13
x
Straight
Horizontal adjust
Crimped
Straight
Vertical adjust
Crimped
Rotor Type X, W, Y, Z only in bulk packaging. Embossed tape packaging on request.
Page 8 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
SHAFTS, KNOBS AND THUMBWHEELS (TOP VIEW, FOR G AND M ROTOR TYPES)
Fig. 1 - Ref. 5016
Fig. 2 - Ref. 5053
Fig. 3 - Ref. 5012
Fig. 4 - Ref. 6053
3
5
5
Fig. 5 - Ref. 5034
8.1
1
2.6
3.7
8.4
34
10.4
Fig. 6 - Ref. 5035
11.5
10
3.1
Fig. 7 - Ref. 5115
Fig. 8 - Ref.: 5116
Fig. 9 - Ref 5119
Fig. 10 - Ref. 5120
4.9
4.9
4.9
4.9
Fig. 16 - Ref. 5039
12
4.5
3.3
15.2
Upon request:
Numbered thumbwheel
Fig. 17 - Ref. 5062
19
21
1
5
1.5
9.5
Fig. 14 - Ref. 5055
4.9
12.5
25.5
15.2
25.5
Fig. 15 - Ref. 6008
Fig. 12 - Ref. 6052
For R rotor
type only
Marking:
configurable
number of
positions
Example of
four positions
marking
Fig. 18 - Ref: 6064
2-gang plastic knob/shaft
25
Ø6
13
12.75
5
Ø1.3
2.5
5
By default, shafts, knobs and thumbweels
are delivered unassembled. If you need the
shaft or knob to be delivered assembled
from the factory, please select the
appropriate rotor in the part number: X, W,
Y or Z.
On request, shafts, knobs and thumbweels
can be delivered at specific positions
(drawing must be provided), otherwise they
are delivered at random position.
The plastic color can be stated in the part
number.
Non flammable plastic available, if
potentiometer is orderer with nonflammable plastic (UL-94V0), the shaft or
knob will be delivered with non-flammable
plastic.
If you wish to use your own plastic shaft/
knob/actuator please contact Piher for
advice about compatible materials.
Page 9 of 10
www.piher.net
PT-10 / PTC-10
10-mm carbon / cermet through-hole potentiometer
POSITIONING
PM
50% ±15°
Default
INITIAL
PF
FINAL
Wiper positioning on initial position is standard. Special delivery positions available on request.
OUR ADVANTAGE
▶Leading-edge innovative position sensing solutions
▷Contactless (Hall-effect and Inductive Technology)
▷Contacting (Potentiometers, Printed Electronics)
▶Engineering design-in support
▶All our products can be customized to fit target application and customer requirement
▶Capability to move seamlessly from development to true high-volume production
▶A global footprint with global engineering and commercial support
▶One-stop shop not limited to position sensors (temperature, pressure, gas,…) through group collaboration
▶Flexibility and entrepreneurship of a medium-sized company with the backing of Amphenol Corporation
CONTACT
ISO 14001
Please always use the latest updated datasheets and 3D models published on our website.
Disclaimer:
The product information in this catalog is for reference purposes. Please consult for the most up to date and accurate design information.
Piher Sensors & Controls S.A., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Piher”), disclaim any and all liability for any
errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product described herein.
Piher disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted
by law. The product specifications do not expand or otherwise modify Piher’s terms and conditions of sale, including but not limited to the warranty expressed therein, which
apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Piher.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling
Piher products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Piher for any damages arising or resulting from
such use or sale. Please contact authorized Piher personnel to obtain written terms and conditions regarding products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners. Information contained in and/or attached to this catalog may be subject to export
control regulations of the European Community, USA, or other countries. Each recipient of this document is responsible to ensure that usage and/or transfer of any information
contained in this document complies with all relevant export control regulations. If you are in any doubt about the export control restrictions that apply to this information,
please contact the sender immediately. For any Piher Exports, Note: All products / technologies are EAR99 Classified commodities. Exports from the United States are in
accordance with the Export Administration Regulations. Diversion contrary to US law is prohibited.
Rev:28032022 © 2021 Piher Sensors & Controls S.A
BUREAU VERITAS
Certification
Piher Sensing Systems
Polígono Industrial Municipal
Vial T2, Nº22
31500 Tudela
Spain
sales@piher.net
Europe:
+34 948 820 450
Americas: +1 636 251 0855
Asia Pacific: +65 9641 8886
India:
+91 9538 686 586
Page 10 of 10
www.piher.net