PT15NV15-103A2020-E-S

Enabling the Electronics Revolution PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer The PT-15 and PTC-15 potentiometers offer control where frequent adjustment is required. The shaftless design allows for employment of different engagement mechanisms, such as a customized shaft, a motor control or a human interface adjustment. This potentiometer can also control variable outputs including frequency, change in motor speed or volume. KEY FEATURES IP54 Up to 38 detents ▶Excellent performance (up to 3% linearity) ▶Carbon or cermet resistive element ▶Up to 38 mechanical detents for tactile feedback ▶Up to 100.000 life cycles ▶IP54 protection ▶Magazine packaging for automatic insertion available ▶Polyester / Alumina substrate ▶Wiper positioned at initial, 50% or fully clockwise ▶Loose and assembled shaft and knobs ▶Linear, logarithmic and antilogarithmic tapers ▶Self extinguishable plastic (UL 94V-0) available ▶SPDT switch and low torque version available Up to 100k Extra-long life Flame retardant APPLICATIONS ELECTRICAL SPECIFICATIONS PT-15 PTC-15 Taper¹ Lin, Log, Alog Range of values¹ Lin Log, Alog Tolerance¹ 100Ω ≤ Rn ≤ 1MΩ 1MΩ < Rn ≤ 5MΩ Max. Voltage Lin Log, Alog Nominal power Lin Log, Alog (Decad. 1.0 - 2.0 - 2.2 - 2.5 - 4.7 - 5.0) 100Ω ≤ Rn ≤ 5MΩ 1KΩ ≤ Rn ≤ 5MΩ Residual resistance¹ ≤ 0.5% Rn (5Ω min.) Equivalent noise resistance ≤ 3% Rn (3Ω min.) Operating temperature -25°C to +70°C ² (-13°F to + 158°F) ± 20% ± 30% 250 VDC 125 VDC 50°C (122°F) 0.25 W 0.12 W ▶Appliance program selection ▶Thermostat adjustment ▶Timer and control relays ▶Consumer electronics ▶Power tool controls ▶Test and measurement equipment 70°C (158°F) 0.50 W 0.25 W -40°C to +90°C ³ (-40°F to + 194°F) 1 Others available on request; 2 Up to 85°C depending on application.; 3 +120°C/+248°F upon request Page 1 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer MECHANICAL SPECIFICATIONS PT-15 PTC-15 Mechanical rotation angle¹ 265° ± 5° Electrical rotation angle 240° ± 20° Torque Rotational Stop 0.5 to 2.5 Ncm (0.7 to 3.4 in-oz) > 10 Ncm (>14 in-oz) Life² Up to 100k cycles Up to 10k cycles 1 240º ± 5º available upon request. Endless rotation available: ST-15; 2 Others check availability ENVIRONMENTAL TESTING Test method (CEI 393-1) PT-15 ΔR(%)- Piher typical test results PTC-15 ΔR(%) - Piher typical test results Electrical life 1.000h at 50°C; 0.15W 1.000h at 70°C; 0.33W ±5% n/a n/a ±2% Mechanical life 1000 cycles at 10 to 15 cpm ±3 % (Rn < 1M ) ±2% Temperature coefficient –25°C; +70°C -40°C; +90°C ±300 ppm/°C (Rn < 100K) n/a n/a ±100 ppm/°C (Rn < 100K) Thermal cycling 16h at 85°C and 2h at -25°C 16h at 90°C and 2h at -40°C ±2.5% n/a n/a ±2% Damp heat 500h at 40°C and 95% relative humidity (RH) ±5% ±2% Vibration 2h each plane at 10Hz - 55Hz ±2% ±2% Storage 6 month at 23°C ±2°C and 50% RH ±2.5% ±2% Out of range values may not comply with these results. Standard test conditions: temperature:23°C ±2°C and 45% to 70% RH RECOMMENDED CONNECTIONS Recommended connection circuit for a position sensor or control application (voltage divider circuit electronic design). VCC E S R A AD RL C RL ≈100 x R POWER RATING CURVE PT-15 PTC-15 W (%) W (%) 100 % 100 % 40 % 40 % 50°C 70°C 70 90 C Page 2 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer HOW TO ORDER Carbon potentiometer (Example: PT15LH01-223A2020-S) Optional features PT15 _ Mounting method2 Series H01 H05 H25 H02 H06 H10 V02 V12 V15 V17 V18 V20 V24 V21 V22 V23 V25 Rotors1 L N G M C F R T W X Y Z - ___ inserted shaft inserted knob horizontal adjust crimped terminals ___ _ Ω-Value3 101 = 100Ω 201 = 200Ω … 504 = 500KΩ 505 = 5MΩ ____ ___ ___ Taper Cut track Detents A = lin. B = log. C = alog. [empty] PCI PCF vertical adjust _ Tolerance4 Life5 0505 = ±5% 0707 = ±7% 1010 = ±10% 2020 = ±20% 3030 = ±30% XXYY = +XX-YY% [empty] = 1K cycles E = 10K cycles U = 100K cycles [empty] PAI PAM PAF P1I P1F P02 … P38 __ _ __ __ Shaft/ Thumbwheel Shaft/Rotor color7 [empty] = none 01 = Fig.1 02 = Fig.2 … 28 = Fig.28 [empty] AM = yellow AZ = blue CR = cream GR = grey MA = brown NA = orange NE = black RO = red VE = green Flammability6 [empty] = standard I = non-flammable _ _ - S Packaging9 [empty] = bulk T = magazines R = embossed tape Torque8 [empty] = standard L = ≤ 1.5 Ncm Wiper position crimped terminals [empty] = initial PM = 50% PF = final Cermet potentiometer (Example: PTC15LH01-223A2020) Optional features PTC15 _ ___ Series Rotors1 Mounting method L N G M C F R T W X Y Z inserted shaft inserted knob H01 H05 H15 H02 H06 H10 V02 V12 V15 V17 V18 V21 V22 V23 V25 horizontal adjust crimped terminals vertical adjust crimped terminals - ___ _ ____ Ω-Value3 Taper Tolerance4 Detents 101 = 100Ω 201 = 200Ω … 504 = 500KΩ 505 = 5MΩ 000 = CM A = lin. B = log. C = alog. 0505 = ±5% 0707 = ±7% 1010 = ±10% 2020 = ±20% 3030 = ±30% XXYY = +XX-YY% [empty] PAI PAM PAF P1I P1F P02 … P38 _ ___ __ __ Shaft/ Thumbwheel Shaft/Rotor color7 [empty] = none 01 = Fig.1 02 = Fig.2 … 28 = Fig.28 [empty] AM = yellow AZ = blue GR = grey MA = brown NA = orange NE = black RO = red VE = green __ Life [empty] = 1K cycles E = 10K cycles _ _ Packaging9 [empty] = bulk T = magazines R = embossed tape Torque8 [empty] = standard L = ≤ 1.5 Ncm Wiper position [empty] = initial PM = 50% PF = final 1. Rotors: "Z" adjustment only available on "H"-mounting versions. Standard color for the “T” rotor: Orange. 2. Mounting method: “V24” terminals material: brass. 3. Ω- Value: XXX - First two digits of Ω-value 000 = CM = 45° switch SPDT version XXX - Number of zeros 45° 4. Tolerance: for custom tolerance please check availability: info@piher.net 5. Life: “U” only available for low-torque versions and to be studied case by case. 6. Non-flammable according to UL 94V-0: housing, rotor and shaft. PTC-15 made of non-flammable material by standard. 7. Shaft/rotor color: Without shaft: only the rotor. With shaft: only the shaft. 8. Torque: Detent option not available with low torque models. 9. Packaging: Magazine packaging available for all H and V12, V02, V21, V15 and V23 mounting. Page 3 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer STANDARD CONFIGURATION PT-15 PTC-15 Life 1.000 cycles Cut track no Detents none Packaging bulk Shaft/thumb wheel none Non-flammability no yes Housing color black cream Rotor color white cream Wiper Position initial Torque 0.5 to 2.5 Ncm Terminal material steel Linearity not controlled n/a brass ROTORS Wiper shown at initial position ±0 .05 3. 05 ±0 .05 4. 05 1 42.5° 5 .0 ±0 .05 ±0 -0 .1 05 4. 3. 8 G Removable shaft or thumbwheel N Removable shaft or thumbwheel 05 3. -0 .1 L Screw driver - through hole 42.5° Wiper position Wiper position Wiper shown positioned at 50% ±0.05 Ø4.05 ±0.05 3.05 1.2 23° With inserted thumbwheel Y Adjustable from terminal side 7.5 +0.3 0.8 +0.5 L Z Adjustable from collector side 7.5 +0.3 4 X Adjustable from collector side 6 L Ø4.02 1.4 With inserted shaft T R 3.52 2.55 ±0.05 Ø4.4 W Adjustable from terminal side 3.35 3.35 +0.1 54° ±0.05 ±0.05 F ±0.05 C ±0.05 M Hexagonal - through hole +0.5 Default delivery is at initial position. Download the STEP file here: https://www.piher.net/piher/?p=916 Page 4 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer MOUNTING METHOD Horizontal adjust / vertical mounting H05 -5mm / H10 with crimped terminals + 15 0.2 6 +0.2 E A = Initial 2.5 5+0.1 S = Wiper +0.1 10 S + 1 0.1 2.5 4 5+0.1 4 A 5+0.1 5 + 1 0.1 5 E = Final H15 - A5 6 +0.1 + 15 0.2 ±0.2 1.3 +0.1 4 19.5 8.8 + 9.6 0 . 2 +0.2 17.1 1.3 10 15 ±0.2 +0.2 6 ±0.2 12 H06 - B +0.2 5+0.1 1.3 +0.2 17.5 10 +0.2 +0.1 10 +0.2 1.3 +0.2 15 ±0.2 17.5 6 ±0.2 10 H01 - 2.5mm / H02 with crimped terminals 4 +0.1 4.4 + 1 0.1 4 5 4 +0.1 5 +0.1 H25 - C5 5 +0.1 1 +0.1 5 Available on request ±0.2 15 6 ±0.2 +0.1 1.3 10 1.3 13.8 12.5 20 ±0.2 15 ±0.2 6 10 4,4 5 +0.1 1 +0.1 5 5 4 5 4 5 +0.1 5 5 5 1 Vertical adjust / horizontal mounting V02 - 12.5mm / V21 with crimped terminals 6 +0.2 15 V12 - 12.5mm / V22 with crimped terminals +0.2 + 15 0.2 6 +0.2 7 7 S = Wiper + 1 0.1 V20 - 15mm (L) + 15 0.2 + 6 0.2 + 15 0.2 7 15 7.5 7.5 7.5 7.5 15 15 7.5 7.5 7 10 10 7 4 + 1 0.1 1.3 +0.1 10 9.3 4 4 4 10 +0.2 1.3 +0.1 A V15 - 15mm / V23 with crimped terminals +0.2 12.5 7.5 12.5 5 5 10 +0.2 8.5 4 +0.2 S E = Final E 6 +0.2 7.5 1.3 +0.1 7.5 A = Initial 10 10 + 1 0.1 7.5 4 15 4 10 7 E 4 A +0.2 +0.2 12.5 7.5 7.5 12.5 5 5 S + 1 0.1 1.3 +0.1 Page 5 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer MOUNTING METHOD Vertical adjust / horizontal mounting V18 - 18.5mm (D) V17 - 17.5mm / V25 with crimped terminals 1.3 18.5 11 7 A 10 + 1 0.1 8.8 +0.2 7.5 4 +0.2 8.8 Ø1.3 +0.1 E 4 E 4 +0.2 7.5 4 S 3.2 7.5 17.5 10 10 17.5 7.5 S +0.2 13.5 7 A 10 + 15 0.2 6 +0.2 13.5 ± 15 0.2 11 ± 6 0.2 +0.1 1 1.3 +0.1 V24 - 15mm (D15) ± 6 0.2 13.5 ± 15 0.2 S (wiper) 13.5 1.3 7.5 3.2 7.5 S 7.5 3.3 10 ±0.2 3.3 7 E A +0.2 A (initial) (final) E 10 1.3 +0.1 +0.1 1 CRIMPED TERMINALS (DETAIL) +0.2 6 3.8 7 2 +0.2 +0 – 0.4 6 +0.2 A 0.9 12.5 A 5 Detail A STANDARD RESISTANCE-VALUES AND TOLERANCES Resistance Ω 100 200 220 250 470 500 1K 2K 2.2K 2.5K 4.7K 5K 10K 20K 22K 25K 47K 50K 100K 200K 220K 250K 470K 500K 1M 2M 2.5M 4.7M 5M Order Code 101 201 221 251 471 501 102 202 222 502 103 205 252 472 Tolerance 203 223 253 473 503 104 204 224 254 474 504 20% 105 255 475 505 30% SWITCH VERSIONS AVAILABLE WITH OR WITHOUT DETENTS 1 CONTACT A 0 CONTACT 1 E A = Initial S = Wiper E = Final 0 45º Standard Specification Power rating: 24V / 15mA ON position resistance: ≤ 5Ω Insulation resistance: ≥ 30MΩ 50 % A S E 45º Mechanical rotation angle: 265º±5º Contact Piher Sensing Systems for ordering information. Page 6 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer TAPERS Standard Example: special custom taper 100% Rn A = Linear B = Log. C = Alog. C R 2 ±5% A B For more information on custom tapers contact Piher Sensing Systems. CUT TRACKS (OPEN CIRCUIT DESIGN) rd PCI PCF A Cut track at the end of travel. Cut track at the beginning of travel. CCW on-off (A) E A S E A S CW on-off (E) A E E Other configurations available upon request. Cut Track not available for PTC-15. DETENTS rd PAM P1i P1F P02 P03 P04 P05 P06 P07 P08 P09 P10 P11 P12 P13 P16 P17 P27 P34 P38 PAI Wiper position B = 34.5º Wiper position B PID PAF B B A = 32.625º B A (wiper positioned at initial) PFD A (wiper positioned at final) Relative detent positions along total mechanical travel •Standard mechanical life is 500 cycles. •Long life versions are available upon request and have the following characteristics at Tª: Potentiometers with 1 to 3 detents up to 10K cycles; Potentiometers with 4 and more detents up to 5K cycles •Please consult Piher Sensing Systems if unique non-overlapping values at each detent position or LOG/ALOG tapers are required. •Different output voltage values can be matched at each detent position (see next section). •Detent torque can vary from 1.2 to 2.5 times the standard potentiometer torque. For all detents versions of more than 13 detents the detent torque will be 0.5 to 3.5 Ncm •For V02, V21, V12, V22, V18 and V24 mounting detent configuration will be studied case by case. •For more than 13 detents versions please contact Piher Sensing Systems. Page 7 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer STEPPED OUTPUTS / CONSTANT VALUE ZONES 100% Un IMPROVED REPEATABILITY When the potentiometer’s wiper is located at detent nº9, the output voltage will be 88.9% Un ±% tolerance. 88.9% Un 77.7% Un 5 26 ° 44.4% Un 2 33.3% Un 1 22.2% Un 8 9 0º 265º 10 A 11.1% Un E S S 0% Un / 0º 1 7 3 55.5% Un A 6 4 66.6% Un 100% 50% = = 2 = 3 = 4 = 5 = 6 = 7 = 8 Wiper position E = 9 A 10 E Constant value zones can be combined with strategically located mechanical detents to provide exact alignment between the electrical output (flat areas) and the mechanical detent position. This provides clear mechanical positions that are not only repeatable, but perfectly aligned electrical outputs at each of the (detent) angles. The detents also prevent output values from changing due to vibration or accidental rotor movements. The result is a higher level of precision in controlling lighting, temperature, motor or other electronic control systems. Contact Piher Sensing Systems for ordering information. POSITIONING PM 50% ±15° PF FINAL Default INITIAL Special delivery positions available on request. PACKAGING Bulk Without shaft: 400 units per box With thumbweel: 200 units per box With shaft: contact Piher Sensing Systems Dimensions (mm): 185x85x80 Page 8 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer SHAFTS AND THUMBWHEELS (TOP VIEW, FOR N, G AND T ROTOR TYPES) Hollow shafts models Solid shafts models C 8 15 5.5 31 33.8 31 Fig. 6 7 8 12 B B 9 9 6.5 9 9 25 A A 12 19 9.5 35 37.8 35 1.4 Ref. 5272 5214 5208 5216 5218 5209 3.7 Fig. 1 2 5 9 10 11 A = Length measured from rotor surface B = Knurling length C = Hollow depth 1.2 Ref. 5219 5220 5207 5227 A 15 16.8 25.3 46 B 9 9 9 5 Slot (1 x 1.4) perpendicular to wiper position. Fig. 12 slot is on line with wiper position. 1 3.7 3.7 A B 6 C 6 5 Fig. 3 - Ref. 5372 Fig. 15 - Ref. 5217 Fig. 17 - Ref. 5210 Fig. 18 - Ref. 5271 Fig. 19 - Ref. 6032* Fig. 20 - Ref. 5369* Ø6 Ø 5.9 Ø6 28.7 11.3 23.1 12 8 12 15 10.7 Ø4 28 Ø4 Ø4 36 o 3 4,1 5º 6 4, Ø6 Fig. 22 - Ref. 6029 Fig. 23 - Ref. 6022 Fig. 29 - Ref. 6162 Ø6 Ø6 23.4 10 41.5 40 o 4. 6 o 42 Fig. 4 - Ref. 5371 16 1.3 Ø6 9.5 6 4. Fig. 28 - Ref. 6055 Fig. 27 - Ref. 5268* Ø6 13.8 12 37,8 Fig. 25 - Ref. 6059 Ø4 26 Fig. 21 - Ref. 6031* Thumbwheel and shafts are delivered unassembled if not specified otherwise in part number code (W, X, Y, Z). The position of the thumbwheel Fig 4 can be indicated in part number code: Initial (default), 50% (PM) or Final (PF), shafts will be delivered at random position by default. Custom specific positions are available for all shafts and thumbwheel on request. The plastic color can be stated in the part number. Non flammable plastic available, if potentiometer is orderer with non-flammable plastic (UL-94V0), the shaft or knob will be delivered with non-flammable plastic. If you wish to use your own plastic shaft/knob/actuator please contact Piher for advice about compatible materials. *Not available in self-extinguishable plastic. Page 9 of 10 www.piher.net PT-15 / PTC-15 15-mm carbon / cermet through-hole potentiometer AVAILABLE PACKAGING OPTIONS Mounting Type Terminal Style Mounting Method Bulk Magazine (35 units) H01 x x H05 x x H06 x x H25 x x H02 x x H10 x x V02 x x V12 x x V15 x x V17 x V18 x V20 x V24 x V21 x V22 x V23 x V25 x Embossed Tape Straight Horizontal adjust Crimped Straight Vertical adjust x x Upon request x x x x Crimped Upon request Rotor Type X, W, Y, Z only in bulk packaging OUR ADVANTAGE ▶Leading-edge innovative position sensing solutions ▷Contactless (Hall-effect and Inductive Technology) ▷Contacting (Potentiometers, Printed Electronics) ▶Engineering design-in support ▶All our products can be customized to fit target application and customer requirement ▶Capability to move seamlessly from development to true high-volume production ▶A global footprint with global engineering and commercial support ▶One-stop shop not limited to position sensors (temperature, pressure, gas,…) through group collaboration ▶Flexibility and entrepreneurship of a medium-sized company with the backing of Amphenol Corporation CONTACT ISO 14001 Please always use the latest updated datasheets and 3D models published on our website. Disclaimer: The product information in this catalog is for reference purposes. Please consult for the most up to date and accurate design information. Piher Sensors & Controls S.A., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Piher”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product described herein. Piher disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Piher’s terms and conditions of sale, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Piher. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Piher products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Piher for any damages arising or resulting from such use or sale. Please contact authorized Piher personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Information contained in and/or attached to this catalog may be subject to export control regulations of the European Community, USA, or other countries. Each recipient of this document is responsible to ensure that usage and/or transfer of any information contained in this document complies with all relevant export control regulations. If you are in any doubt about the export control restrictions that apply to this information, please contact the sender immediately. For any Piher Exports, Note: All products / technologies are EAR99 Classified commodities. Exports from the United States are in accordance with the Export Administration Regulations. Diversion contrary to US law is prohibited. Rev:18072022 © 2022 Piher Sensors & Controls S.A BUREAU VERITAS Certification Piher Sensing Systems Polígono Industrial Municipal Vial T2, Nº22 31500 Tudela Spain sales@piher.net Europe: +34 948 820 450 Americas: +1 636 251 0855 Asia Pacific: +65 9641 8886 India: +91 9538 686 586 Page 10 of 10 www.piher.net