PT6KV-103A2020-PM

Enabling the Electronics Revolution PT-6 6-mm carbon through-hole trimmer potentiometer KEY FEATURES IP54 Up to 10 detents ▶Excellent performance ▶Carbon resistive element ▶Up to 10 mechanical detents ▶Up to 10.000 life cycles ▶IP54 protection ▶Magazines packaging for automatic insertion ▶Polyester substrate ▶Wiper positioned at initial, 50% or fully clockwise ▶Loose and assembled shaft and knobs ▶Linear, logarithmic and antilogarithmic tapers ▶SPDT switch function On request ▶Embossed tape packaging Pb Leadfree Flame retardant The only 6 mm miniature trimmer potentiometer with optional stop positions for haptic feedback. Up to 10 detents APPLICATIONS ELECTRICAL SPECIFICATIONS Taper* Lin, Log, Alog Range of values* Lin Log, Alog Tolerance* 220Ω ≤ Rn ≤ 1MΩ 1MΩ < Rn ≤ 5MΩ Max. Voltage Lin Log, Alog Nominal power 50°C (122°F) Lin Log, Alog (Decad. 1.0 - 2.0 - 2.2 - 2.5 - 4.7 - 5.0) 220Ω ≤ Rn ≤ 5MΩ 1KΩ ≤ Rn ≤ 5MΩ Residual resistance ≤ 0.5% Rn (5Ω min.) Equivalent noise resistance ≤ 3% Rn (3Ω min.) Operating temperature ** -25°C to +70°C (-13°F to + 158°F) ± 20% ± 30% ▶Appliance program selection ▶Thermostat adjustment ▶Timer and control relays ▶Consumer electronics ▶Power tool controls ▶Test and measurement equipment 100 VDC 50 VDC 0.1 W 0.05 W * Others available on request ** Up to 85°C depending on application. Page 1 of 7 www.piher.net PT-6 6-mm carbon through-hole trimmer potentiometer MECHANICAL SPECIFICATIONS Mechanical rotation angle 235° ± 5° Electrical rotation angle* 200° ± 20° Torque Rotational Stop 0.2 to 2 Ncm (0.3 to 2.7 in-oz) > 4 Ncm (>7 in-oz) Life** up to 10.000 cycles *Increased rotational angle of 215º± 20° available upon request ** Others available on request ENVIRONMENTAL TESTING Test conditions (CEI 393-1) ΔR(%) - Typical test results Electrical life 1.000h at 50°C; 0.1 W ±5% Mechanical life 1000 cycles at 10 to15 cpm ±3% (Rn < 1M ) Temperature coefficient –25° C; +70° C ±300 ppm/°C C (Rn < 100K) Thermal cycling 16h at 85°C and 2h at -25°C ±2.5% Damp heat 500h at 40°C and 95% relative humidity (RH) ±5% Vibration 2h each plane at 10Hz - 55Hz ±2% Storage 6 month at 23°C ±2°C and 50% RH ±2.5% Out of range values may not comply with these results. Standard test conditions: temperature:23°C ±2°C and 45% to 70% RH. Mechanical life of detented versions is 100 cycles RECOMMENDED CONNECTIONS Recommended connection circuit for a position sensor or control application (voltage divider circuit electronic design). VCC E S R A AD RL C RL ≈100 x R POWER RATING CURVE W (%) 100 % 40 % 50 70 C Page 2 of 7 www.piher.net PT-6 6-mm carbon through-hole trimmer potentiometer HOW TO ORDER Example: PT6KV-221A2020 PT6 _ ___ Series Rotors1 Mounting method A K M Q W X H = horizontal adjust V= vertical adjust inserted knob / shaft - - _ Optional features - _ _ __ ___ _ ____ Ω-Value2 Taper Tolerance3 Detents4 Packaging5 221 = 220Ω … 505 = 5MΩ 000 = CM A = lin. B = log. C = alog 0505 = ±5% 0707 = ±7% 1010 = ±10% 2020 = ±20% 3030 = ±30% XXYY = +XX-YY% [empty] [empty] = bulk T = magazines ___ P04 P05 P06 P07 P08 P10 Life Shaft/Knob [empty] = none 1 = Fig.1 2 = Fig.2 … 5 = Fig.5 - __ Knob/Rotor color6 Wiper position [empty] AM = yellow AZ = blue BL = white CR = cream GR = grey IN = natural NE = black RO = red VE = green VI = violet [empty] = initial PM = 50% PF = final Crimping [empty] = crimped SC = straight [empty] = 1K cycles E = 10K cycles 1. Rotors: "X" rotor only available on "H"-mounting versions. 2. Ω- Value: XXX - First two digits of Ω-value 000 = CM = switch SPDT version XXX - Number of zeros 45° 3. Tolerance: for custom tolerance please check availability: info@piher.net 4. Detents: Detented versions use purple rotor color (rotor color code "VI"). Ordering code example: PT6KH-254A2020-P04-VI 5. Packaging: Only for “V” mounting method. “W” rotor with shaft Fig. 2 is not available in magazines. Embossed tape packaging on request. 6. Without knob or shaft: only the rotor. With knob or shaft: only the knob/shaft. Default colour for knob/shaft is cream STANDARD CONFIGURATION PT-6 Life 1.000 cycles (forth and back the mechanical angle travel) Detents none Housing color black Rotor color white Wiper Position initial Packaging bulk ORDER CODE EXAMPLES PT6WV-104A1010-5NE-SC 6mm potentiometer with factory pre-inserted knob, V mounting method (vertical adjustment), 100K resistive value, linear taper, 10% resistive tolerance, black knob ref. 6148 and straight terminals (not crimped). PT6KH-103A2020 6mm potentiometer with rotor “K” (cross shape), H mounting method (horizontal adjustment), 10K resistive value, linear taper, 20% resistive tolerance and crimped terminals. Page 3 of 7 www.piher.net _ PT-6 6-mm carbon through-hole trimmer potentiometer ROTORS Q Cross slot through hole K Cross slot through hole colour: pink ±0.1 ±0.05 1.85 colour: pink +0.07 -0.03 1.4 1.5 ±0.05 ±0.05 0.6 0.65 ±0.1 1.8 A Hexagonal through hole M Hexagonal through hole X Adjustable from collector side 6 ±0.1 1.8 ±0.1 6 4.3 4.3 0.6 0.6 1.8 W Adjustable from terminal side 0.7 ±0.05 ±0.05 With inserted knob / shaft. Example with knob ref. 5155 With inserted knob / shaft. Example with knob ref. 5155 Default delivery is at initial position. Wipers are shown positioned at 50% for the picture. MOUNTING METHOD 1.8 V = Vertical Adjustment - Horizontal Mounting 0.6 4 6.3 0.9 S +0.1 2.5 2.5 2.5 2.5 5 3.3 2.5 2.5 A 3.5 E 0.7 ±0.05 2.5 2.5 H = Horizontal Adjustment - Vertical Mounting 3.5 6.3 1.8 +0.1 Download STEP files here: https://piher.net/piher/?p=894 5 4.5 0.6 0.9 S (wiper) 2.5 2.5 2.5 2.5 A S (final) E A (ini�al) E Page 4 of 7 www.piher.net PT-6 6-mm carbon through-hole trimmer potentiometer CRIMPING Crimped Non-crimped 4 3.3 3.5 0.3 1.6 3.3 X 0.25 Collector (S) 0.30 0.8 0.25 X Terminals 7.5 0.7 SMD MOUNTING AVAILABLE PS-6 N-6 For more information visit: www.piher.net STANDARD RESISTANCE-VALUES AND TOLERANCES Resistance Ω 100 200 220 250 470 500 1K 2K 2.2K 2.5K 4.7K 5K 10K 20K 22K 25K 47K 50K 100K 200K 220K 250K 470K 500K 1M 2M 2.5M 4.7M 5M Order Code 101 201 221 251 471 501 102 202 222 502 103 205 Tolerance 252 472 30% 203 223 253 473 503 104 204 224 254 474 504 105 20% 255 475 505 30% TAPERS Standard Example: special custom taper 100% Rn C A R 2 ±5% A = Linear B = Log. C = Alog. B For more information on custom tapers contact Piher Sensing Systems. SWITCH VERSION 1 CONTACT A 0 CONTACT 1 A = Initial S = Wiper E = Final A S E E 0 45º 50 % 45º Mechanical rotation angle: 235º±5º Contact Piher Sensing Systems for ordering information. Page 5 of 7 www.piher.net PT-6 6-mm carbon through-hole trimmer potentiometer DETENTS / STOP POSITIONS P04 P06 P05 P08 P07 Relative detent positions along total mechanical travel P10 travel All detented versions will be studied case by case, more than 10 detents available on request. Unless otherwise specified the detents are evenly spaced (using the end points as reference). Standard mechanical life of detented versions: 100 cycles. Long life versions are available on request. Detent torque can vary from 1.2 to 2.5 times the standard potentiometer torque. Rotor color of detented versions is purple-violet. PACKAGING Bulk (1000 units per box) Magazine / Automatic Insertion (80 units per magazine) All models PT-6 V models PT-6 WV models 13 530 8 8 530 Dimensions (mm): 185x85x40 Embossed tape/reel packaging on request. WIPER POSITION PM 50% ±15° Default INITIAL PF FINAL Wiper positioning on initial position is standard. Special delivery positions available on request. DUAL GANG METAL SHAFT ON REQUEST - REF.: 6060 17.5 5 2.5 5 Page 6 of 7 www.piher.net PT-6 6-mm carbon through-hole trimmer potentiometer KNOBS / SHAFTS (FOR K ROTOR) Fig. 2 - Ref. 6132 Fig. 1 - Ref.: 5155 Shaft - Not suitable for magazine packaging. 6.3 13.30 6 4.3 10 1 1.87 0.64 2.90 2.54 1.50 2 1.2 2.2 R1 5 5 Fig 4 - Ref.: 6172 Fig. 3 - Ref.: 5141 Color: grey* Color: grey* 3.8 6.3 4.3 6 6 3.4 3.3 2.35 0.8 2.6 6.3 0.8 2.2 1.2 R1 2.2 1.87 Fig. 5 - Ref.: 6148 Fig. 6 - Ref.: 6160 For V models only. Default color: cream. For V models only. Default color: cream. 3.2 2 6.5 6.5 3.8 6.3 3.85 5.5 0.8 3.8 2.2 6.3 2.2 Position of the wiper. If you wish to use your own plastic shaft/knob/actuator please contact Piher Sensing Systems for advice about compatible materials. Shaft and knobs (Fig 1 to 4) are delivered unassembled if not specified otherwise in part number code (“W” or “X”). The position of assembled knobs can be indicated in part number code: Initial (default), 50% (PM) or Final (PF). Mounted shaft Fig. 2 by standard will be delivered at random position. Custom specific positions are available for shaft and all knobs on request. *For other colors check availability. OUR ADVANTAGE ▶Leading-edge innovative position sensing solutions ▷Contactless (Hall-effect and Inductive Technology) ▷Contacting (Potentiometers, Printed Electronics) ▶Engineering design-in support ▶All our products can be customized to fit target application and customer requirement ▶Capability to move seamlessly from development to true high-volume production ▶A global footprint with global engineering and commercial support ▶One-stop shop not limited to position sensors (temperature, pressure, gas,…) through group collaboration ▶Flexibility and entrepreneurship of a medium-sized company with the backing of Amphenol Corporation ISO 14001 Please always use the latest updated datasheets and 3D models published on our website. Disclaimer: The product information in this catalog is for reference purposes. Please consult for the most up to date and accurate design information. Piher Sensors & Controls S.A., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Piher”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product described herein. Piher disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Piher’s terms and conditions of sale, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Piher. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Piher products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Piher for any damages arising or resulting from such use or sale. Please contact authorized Piher personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Information contained in and/or attached to this catalogue may be subject to export control regulations of the European Community, USA, or other countries. Each recipient of this document is responsible to ensure that usage and/or transfer of any information contained in this document complies with all relevant export control regulations. If you are in any doubt about the export control restrictions that apply to this information, please contact the sender immediately. For any Piher Exports, Note: All products / technologies are EAR99 Classified commodities. Exports from the United States are in accordance with the Export Administration Regulations. Diversion contrary to US law is prohibited. Rev:18072022 © 2022 Piher Sensors & Controls S.A BUREAU VERITAS Certification CONTACT Piher Sensing Systems Polígono Industrial Municipal Vial T2, Nº22 31500 Tudela Spain sales@piher.net Europe: +34 948 820 450 Americas: +1 636 251 0855 Asia Pacific: +65 9641 8886 India: +91 9538 686 586 Page 7 of 7 www.piher.net