PTC15NV02-104A2020

PTC-15 15 mm Cermet Potentiometer FEATURES - Cermet resistive element. - Plastic material according to UL94V-0. - Alumina substrate. - IP54 protection according to IEC 60529. - Also upon request: • Wiper positioned at initial, 50% or fully clockwise. • Long life model for low cost control pot. applications. • Supplied in magazines for automatic insertion. • Low torque option. • Available as SPDT switch. • Laser trimming for tighter tolerances. • Mechanical detents. • Special tapers. MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS – Range of values* – Mechanical rotation angle: 265° ± 5° – Electrical rotation angle: 240° ± 20° – Torque: 0.5 to 2.5 Ncm. (0.7 to 3.4 in-oz) – Stop torque: > 10 Ncm. ( >14 in-oz) – Max. Voltage: 250 VDC (lin) 125 VDC (no lin) – Life*: Up to 10K cycles – Nominal Power 70°C (158°F) (see power rating curve) 0.50 W (lin) 0.25 W (no lin) – Tolerance*: ± 20% ± 30% – Taper* (Log. & Alog. only Rn 1K) Lin ; Log; Alog. – Residual resistance*: – Equivalent Noise Resistance: * Others check availability. – Operating temperature**: –40°C + 90°C (–40°F + 194°F) ** Up to +120ºC depending on application. Check availability. HOW TO ORDER OPTIONAL EXTRAS PTC15 L Series Rotors C F G L M N R T X W Y Z H01 Code Mounting Method H01 H05 H15 H06 H02 H10 V02 V12 V15 V17 V18 V21 V22 V23 H2.5 H5 HA5 B H2.5P H5P V12.5 VA V15 V17.5 D V12.5P VAP V15P (See note 2) 223 A 2020 - Taper Long Life Shaft Thum. Wiper position A = Lin. B = Log. C = Alog. E= Long life 01 – Fig. 1 PM = 50% PF = Final (See note 5) (1) (2) (3) (4) (5) (6) 28 – Fig. 28 (See note 9) Value 223 = 22 K 504 = 500 K 505 = 5 M 000 = C M Tolerance Detents 0505 = ± 5% 0707 = ± 7% 1010 = ± 10% 2020 = ± 20% 3030 = ± 30% PAI PAM PAF P1I P1F P02 (See note 4) Magazine T Shaft/rotor colour RO= Red NE= Black VE= Green AM= Yellow AZ = Blue MA= Brown GR= Grey NA= Orange (See note 8) Torque – = Standard L= Low Torque (See note 7) (See note 6) (See note 3) (See note 1) NOTES - P38 "Z" adjustment only available on "H" versions. Standard colour for the “T” rotor: Orange Terminals styles: "P" are crimped terminals. V=Vertical adjust; H=Horizontal Adjust Value Example: Code: 10 1 Numb of zeros First two digits of the value. 000 = CM: SPDT switch 45° Code: 07 05 Example: +7% -5% negative tolerance Non standard tolerance, check availability. positive tolerance Standard: 1K cycles Life Long life: 10K cycles Potentiometer without shaft: only rotor Colour shaft/ rotor: Potentiometer with shaft: only shaft (7) (8) (9) Magazines (35 pcs/mag): available for VA (12.5), V (12.5), V (12.5P), V (15), V15 (P) and H models. For more information please contact your nearest Piher supplier. If you wish to use your own custom plastic shaft/knob/actuator please contact Piher for advice about compatible materials. NOTE: The information contained here should be used for reference purposes only. www.piher.net 56 HOW TO ORDER CUSTOM DRAWING STANDARD OPTIONS PTC-15 LH 01 + DRAWING NUMBER (Max. 16 digits) This way of ordering should be used for options which are not included in the "How to order" standard and optional extras. Detents None Rotor colour Natural Shaft colour Natural Wiper position Initial Torque Standard Life 1000 cycles ROTORS G= Removable shaft or thumbwheel Removable shaft or thumbwheel 23° Ø4.4 M= Rotor C Hexagonal thru hole Rotor F With shaft Rotor R Rotor T With thumbwheel 7.5 +0.3 7.5 +0.3 +0.5 L X = Adjustable from collector side +0.5 1.4 0.8 6 L ±0.05 ±0.05 1.2 3.05 2.55 Ø4.05 ±0.05 Y= Adjustable from terminal side W = Adjustable from terminal side 4 Screw driver thru hole ±0.05 Wiper position ±0.05 N= Ø4.02 42.5° Wiper position L= 3.35 ±0.05 3.35 54° 3.52 +0.1 ±0 .05 3. 05 ±0 .05 .1 1 -0 4. 05 5 0.0 42.5° 5 .0 ±0 05 4. .1 ± 05 3. 3. 8 -0 ±0.05 Wipers positioned at 50% (without shaft) Wipers positioned at initial (without shaft) Z= Adjustable from collector side VERTICAL MOUNTING – HORIZONTAL ADJUSTMENT + 15 0.2 6 +0.2 B 5+0.1 2.5 + 1 0.1 2.5 +0.1 4 E 4 S A 5+0.1 1.3 8.8 17.5 10 +0.1 10 +0.2 +0.2 1.3 + 9.6 0 . 2 +0.2 17.1 + 15 0.2 6 +0.2 h (2.5) 4.4 +0.1 +0.1 4.4 4 + 1 0.1 4 A = Initial S = Wiper E = Final + 15 0.2 19.5 17.5 4 5+0.1 5+0.1 5 +0.1 5 +0.1 +0.1 5 4 5 + 1 0.1 5 1.3 10 ±0.2 12 6 +0.2 ha5 10 +0.1 10 +0.2 +0.2 1.3 +0.2 + 15 0.2 6 +0.2 h (5) 1 +0.1 5 HORIZONTAL MOUNTING – VERTICAL ADJUSTMENT + 15 0.2 6 +0.2 v (12.5) D 7 + 15 0.2 6 +0.2 13.5 13.5 1.3 +0.2 ±0.2 7 4 + 1 0.1 1.3 +0.1 A = Initial S = Wiper E = Final www.piher.net 11 3.2 18.5 11 7 10 57 +0.2 8.8 +0.2 7.5 4 8.8 4 10 E 4 A 12.5 7.5 7.5 12.5 5 5 S +0.1 1 1.3 +0.1 HORIZONTAL MOUNTING – VERTICAL ADJUSTMENT 15 ±0.2 7.5 7 17.5 10 17.5 12.5 7.5 7.5 12.5 5 5 6±0.2 v (17.5) 7 10 15 ±0.2 7.5 6 ±0.2 va (12.5) 10 4 +0.2 8.5 4 +0.2 + 15 0.2 6 +0.2 10 10 +0.2 7.5 4 +0.2 1+0.1 1.3 +0.1 7 7.5 7.5 15 15 7.5 7.5 v (15) 1.3 +0.1 + 1 0.1 4 10 10 +0.2 7 +0.2 + 1 0.1 4 10 4 1.3 +0.1 13 detents example DETENT DETAILS 15 SP A 10 10 17.5 ER Ø1.3 IN PIH 6 5 5 5 5 1 POWER RATING CURVE CRIMPED TERMINALS (DETAIL) 6 +0.2 +0.2 6 100 % 3.8 7 2 +0.2 +0 – 0.4 W (%) 40 % A 0.9 12.5 A Detail A 5 70 TAPER C 90 POSITIONING Please note relative terminal positions when ordering non linear tapers. P.M. A = Linear B = Log. C = Alog. C 50% +20º 100% Rn A B Standard www.piher.net R 2 + 5% P.F. CCW Std. Position = CCW Special curve example 58 CW STANDARD SWITCH VERSION 1 CONTACT SPDT Switch A SW Standard specs. 0 Power Rating: 24V / 15mA 45 ON position resistance: 5 CONTACT 0 1 Insulation Resistance: 30 M E Please contact Piher for ordering information. 0 50 % 45º 45º Mechanical rotation angle: 265º±5º TYPICAL VARIATIONS TESTS ELECTRICAL LIFE 1.000 h. @ 70°C; 0.5 W ±5% MECHANICAL LIFE (CYCLES) 1000 @ 10 CPM ...15 CPM ± 2 % (Rn < 1 M TEMPERATURE COEFFICIENT –40° C; +90° C ± 100 ppm (Rn