RJMG1V200T1015R

Amphenol® Amphenol Taiwan Corporation PRODUCT SPECIFICATION Sheet of 1 5 Rev. A PS-R914 RJ45 Express Connectors Title: Part Number: RJMG1V2XXT101XR Description: TOP ENTRY PCB JACK Revisions Control Rev. ECN Number Originator Approval Issue Date A NE-13104 Jophy Li Roger Tsai 7-9-2013 Product Specification Origination Originator: Date: Checked by: Date: Approved by: Date: Jophy Li 2013.7.9 Roger Tsai 2013.7.9 Roger Tsai 2013.7.9 This document is the property of Amphenol Corporation and is delivered on the express condition that it is not to be disclosed reproduced or used, in whole or in part, for manufacture or sale by anyone other than Amphenol Corporation without its prior consent, and that no right is granted to disclose or to use any information in this document. © Amphenol Corporation 1992, 2013 All international rights are reserved. Amphenol® is a trademark of Amphenol Corporation. Amphenol® Amphenol Taiwan Corporation PRODUCT SPECIFICATION Sheet 2 PS-R914 of 5 Rev. A 1.0 SCOPE This document contains specific electrical and mechanical requirements for the RJ45 express TOP ENTRY PCB JACK connector to insure functionality and reliability. 0.5 APPLICABLE DOCUMENTS The following document, of the latest issue in effect at the time of performance of the qualification tests, shall form a part of this specification to the extent specified herewith. EIA-364 MIL-STD-202F Test methods for electrical connectors Test methods for electrical component parts Underwriters’ Laboratories, Inc. UL-STD-94 Tests for flammability of plastic materials for parts in devices and li 3.0 REQUIREMENTS 3.1 Materials 3.1.1 Housing、IN’S • • High temperature thermoplastic, UL94V-0 rated Color- Black 3.1.2 Contacts • Phosphor bronze • Contact area- Gold 30µ"minimum or • • Solder area- Tin plating Under plate - Nickel under plating overall 3.1.3 Shield • BRASS • Nickel Plating 3.1.4 Transformer • PCB • CORE • GLUE SHELL • PIN • BLACK GLUE • SOLDER WIRE • ENAMELED WIRE • RESISTOR • CAPACITOR This document is the property of Amphenol Corporation and is delivered on the express condition that it is not to be disclosed reproduced or used, in whole or in part, for manufacture or sale by anyone other than Amphenol Corporation without its prior consent, and that no right is granted to disclose or to use any information in this document. Amphenol® Amphenol Taiwan Corporation Sheet PRODUCT SPECIFICATION 3 PS-R914 of 5 Rev. A 3.2 Ratings 3.2.1 Voltage: 150 Volts AC(RMS)/DC. 3.2.2 Current: 1.5A maximum per contact 3.2.3 Operating Temperature: 0°C ~ 70°C 3.2.4 Shipping and Storage Temperature: -40°C ~ 85°C 3.3 Test Requirements and Procedures Summary TEST ITEM 1 Examination of Product REQUIREMENT Meets requirements of product drawing. No physical damage. PROCEDURE Per EIA-364-18 Visual, dimensional and functional inspection ELECTRICAL REQUIREMENT 2 Dielectric withstanding Voltage No Breakdown 3 LCR Test No Breakdown Per EIA-364-20 Subject mated connector with a. voltage of 1500VAC for 1 minute between input to output. MECHANICAL REQUIREMENT TEST ITEM REQUIREMENT PROCEDURE 4 Mating force 20 N maximum per contact pair Per EIA-364-13 Insertion speed at 25±3mm per minute 5 Unmating force 80 N minimum per contact pair Per EIA-364-13 Withdraw speed at 25±3mm per minute 6 Durability No defects & Transformer test OK Per EIA-364-09 Perform 750 cycle unplug/ plug cycles This document is the property of Amphenol Corporation and is delivered on the express condition that it is not to be disclosed reproduced or used, in whole or in part, for manufacture or sale by anyone other than Amphenol Corporation without its prior consent, and that no right is granted to disclose or to use any information in this document. Amphenol® Amphenol Taiwan Corporation Sheet PRODUCT SPECIFICATION 4 PS-R914 of 5 Rev. A ENVIRONMENTAL REQUIREMENTS 7 Salt Spray No detrimental corrosion allowed in contact area and base metal exposed & LCR test OK 8 Solderability 95% of immersed area must show no voids and pin holes 9 Resistance to reflow soldering Heat No damage&LCR test OK Per EIA-363-26, test condition B Subject mated connectors to 35 ± 2ºC and 5 ± 1% salt condition for 24 hours. After test, rinse the sample with water and recondition the room temperature for 1 hour. Per EIA-364-52 Soldering time: 4-5 second (Use flux) Solder Temperature: 245±50C IR temperature 260±50C max 3.4 Recommended IR Reflow Profile(Lead-free) This document is the property of Amphenol Corporation and is delivered on the express condition that it is not to be disclosed reproduced or used, in whole or in part, for manufacture or sale by anyone other than Amphenol Corporation without its prior consent, and that no right is granted to disclose or to use any information in this document. Amphenol® Amphenol Taiwan Corporation Sheet PRODUCT SPECIFICATION 5 PS-R914 of 5 Rev. A 3.5 PRODUCT QUALIFICATION AND REQUALIFICATION TEST SEQUENCE Test or Examination Examination of Product Dielectric withstanding Voltage LCR Test A B 1,5 1 Test Group C D E Test Sequence (a) 1 G 1,5 1,5 1,5 1,5 2,4 2,4 2,4 2,4 3 2,4 Mating force 2 Unmating force 2 Durability 3 Salt Spray Solderability Resistance to reflow soldering Heat Sample size F 3 3 3 2 2 2 2 2 2 2 NOTE：（a）Numbers indicate sequence in which tests are performed. （b）Discontinuities shall not take place in this test group, during tests. List of Appendix … Product Drawing RJ45 series, TOP ENTRY PCB JACK. This document is the property of Amphenol Corporation and is delivered on the express condition that it is not to be disclosed reproduced or used, in whole or in part, for manufacture or sale by anyone other than Amphenol Corporation without its prior consent, and that no right is granted to disclose or to use any information in this document.