USBFTV2SA2G10A

ROHS compliant N & BZ USBF TV Transversally Sealed Receptacles In some applications, a transversal sealing for the receptacle is a « must ». This will prevent fluids and dust from going through the receptacle when plug or cap are not mated to the receptacle. The sealed solution (version "S") has a compound at the rear of the receptacle below. In addition, the Sealed USBF TV has been successfully tested in very high vibration corresponding to airplane applications. Main characteristics n Sealed against fluids and dusts (IP68) n Shock, Vibration and Traction resistant n No cabling operation in field and no tools required n Improved EMI protection n Tri Start Thread coupling mechanism (MIL-DTL-38999 series III type) with anti decoupling device n 2 mechanical Coding / Polarization possibilities by the user (receptacle insert rotation) n USBF TV plug retention in the receptacle: 100 N in the axis n Mating cycles: 500 minimum n Embedded Computers n Data Acquisition and transmission in harsh environment n Railways n Battelfield Communication Systems n Navy Systems Data Transmission USB Specification 2.0 Data Rate: Up to 480 Mb/s for High Speed USB Environmental Protection n Sealing (when mated): IP68 (Temporary immersion) n Salt Spray: 48 h with Nickel plating > 500 h with Olive Drab Cadmium 1000 h with marine bronze shell n Fire Retardant / Low Smoke: UL94 V0 and NF F 16 101 & 16 102 n Vibrations: 10 – 500 Hz, 10 g, 3 axes: no discontinuity > 1micro s n Shocks: IK06: weight of 250 g drop from 40 cm [15.75 in] onto connectors (mated pair) n Humidity: 21 days, 43°C, 98% humidity n Temperature Range: - 40°C / +85°C Amphenol Applications Part Number Code Series USB Field TV USBF TV 2PES A 2 N 03 A Shell Type 2S : Square flange receptacle 2PES: Square flange receptacle + backshell + plastic gland 2PEMS: Square flange receptacle + backshell + metal gland 7S: Jam nut receptacle 7PES: Jam nut receptacle + backshell + plastic gland 7PEMS: Jam nut receptacle + backshell + metal gland Coding "A" (Standard) or "B" Back Terminations 2: Rugged USB cable (see corresponding datasheet page 94) Shells Plating N: Nickel G: Olive drab cadmium plating USB cable length 03: 30 cm [11.81 inches] 05: 50 cm [19.68 inches] 10: 1 meter [39.37 inches] USB cable end A: Standard USB-A plug OPEN: Open cable (no connector) Examples: - Olive Drab Cadmium Square Flange Receptacle with 30 cm of USB cable and standard USB-A plug: USBF TV 2S G 03 A - Nickel Jam Nut Receptacle + backshell + plastic gland, with 1 meter of USB cable, and a standard USBA-A plug: USBF TV 7PES N10 A 75 Receptacles n Square flange receptacle 4 mounting holes: Shell type 2 USBF TV 2SA XXX n Jam nut receptacle Hexagonal Nut mounting: Shell type 7 USBF TV 7SA XXX n Amphenol mination type 1: sealed) Panel Drilling Panel Drilling Jam nut receptacle Hexagonal Nut mounting: Shell type 7 72.7 [2.862] Backshell used with back termination type 2: Solder (Sealed – IP68) USBFTV 2PE(M) SA2XXX / USBFTV 7PE(M) SA2 XXX Panel Drilling Cordset End USB Cable end type "A" 76 USB Cable type "OPEN" NEW USBF TV ROHS compliant N & BZ Hermetic Receptacles In some applications, a transversal hermiticity for the receptacle is a « must ». This will prevent gas from going through the receptacle when plug or cap are not mated to the receptacle. The hermetic solution (version "H") has a compound at the rear of the receptacle. Helium leakage is less than 1.10-6 cm3 per second [0.1 micron cubit ft per hour] at one bar [15 psi] pressure differential. Applications n Embedded Computers n Data Acquisition and transmission in harsh environment n Railways n Battelfield Communication Systems n Navy Systems Data Transmission Main characteristics n Same as the USBF TV (see page 76)... a complete IP68 sealing of the receptacle is added (even with no plug or no protective cap mated). n Outside dimensions are the same as the standard USBF TV (USB-A). n Vibrations : the compounded version of the USBF TV has been tested in vibration following the NAS 1599 Aeronautic specification (Ambient temperature): 5 - 3000 Hz, 20g, 2.5 mm [.1 inch] double amplitude, 3 axes, 12 hours Note: this specification exceeds MIL-C-26500 requirements. USB Specification 2.0 Data Rate: up to 480 Mb/s for High Speed USB IMPORTANT NOTE Due to the compound, the coding of the connector must be done in the factory: use the codes A or B in the part number. Example: USBFTV 2H A 2 N 03 A Amphenol MAIN KEY USB insulation on the left USB insulation on the right PLUG RECEPTACLE Part Number Code Series USB Field TV USBF TV 2H A 2 N 03 A Shell Type 2H : Hermetic square flange receptacle 2PEH: Hermetic square flange receptacle + backshell + plastic gland 2PEMH: Hermetic square flange receptacle + backshell + metal gland 7H: Hermetic jam nut receptacle 7PEH: Hermetic jam nut receptacle + backshell + plastic gland 7PEMH: Hermetic jam nut receptacle + backshell + metal gland Coding "A" (Standard) or "B" Back Terminations 2: Rugged USB cable (see corresponding datasheet page 94) Shells Plating N: Nickel G: Olive drab cadmium plating USB cable length 03: 30 cm [11.81 inches] 05: 50 cm [19.68 inches] 10: 1 meter [39.37 inches] USB cable end A: Standard USB-A plug OPEN: Open cable (no connector) Examples: - Olive Drab Cadmium Hermetic Square Flange Receptacle with 30 cm of USB cable and standard USB-A plug: USBF TV 2H G 03 A - Nickel Hermetic Jam Nut Receptacle + backshell + plastic gland, with 1 meter of USB cable, and a standard USBA-A plug: USBF TV 7PEH N10 A 77