AS1343

Datasheet AS1343 4 2 V, 1 - 2 C e l l s , M i c r o p o w e r, D C - D C B o o s t C o n v e r t e r 1 General Description The AS1343 boost converter contains a 1.4A internal switch in a tiny TDFN-10 3x3mm package. The device operates from a 0.9V to 3.6V supply, and can boost voltages up to 42V output. The output voltage can easily be adjusted by an external resistor divider. The AS1343 uses a unique control scheme providing the highest efficiency over a wide range of load conditions. An internal 1.4A MOSFET reduces external component count, and a fixed high switching frequency (1MHz) allows for tiny surface-mount components. The AS1343 also features power-OK circuitry which monitors the output voltage. Additionally the AS1343 features a low quiescent supply current and a shutdown mode to save power. During shutdown an output disconnect switch separates the input from the output. The AS1343 is ideal for LCD or OLED panels with low current requirements and can also be used in a wide range of other applications. The device is available in a low-profile TDFN-10 3x3mm package. 2 Key Features ! ! ! 5.5V to 42V Adjustable Output Voltage 0.9V to 3.6V Supply Voltage Range High Output Currents: - 30mA @ 12V VOUT, from 1.5V VCC - 40mA @ 24V VOUT, from 2.5V VCC Efficiency: Up to 85% Switching Frequency: 1MHz Output Disconnect Function Output Discharge Function Power-OK Output Quiescent Current: 22µA Shutdown Current: 0.1µA TDFN-10 3x3mm Package ! ! ! ! ! ! ! ! 3 Applications The device is ideal for OLED display power supply, LCD bias generators, mobile/cordless phones, palmtop computers, PDAs and organizers, handy terminals, driving LEDs or any other portable, battery-powered device. Figure 1. AS1343 - Typical Application Diagram L1 VCC = 0.9V to 3.6V CIN VCC R3 POK On Off LX SWOUT VOUT D1 VOUT = 5.5V to 42V COUT AS1343 R1 EN FB R2 GND PGND www.austriamicrosystems.com Revision 1.04 1 - 17 AS1343 Datasheet - P i n o u t 4 Pinout Pin Assignments Figure 2. Pin Assignments (Top View) EN 1 POK 2 GND 3 VCC 4 PGND 5 10 FB 9 VOUT AS1343 8 GND 7 SWOUT 6 LX Pin Descriptions Table 1. Pin Descriptions Pin Number 1 Pin Name EN Description Active-Low enable Input. A logic low on this pin shuts down the device and reduces the supply current to 0.1µA. GND: device in shutdown. VCC : normal operation. Power-OK. 0: VOUT < 90% of VOUTNOM. 1: VOUT > 90% of VOUTNOM. Ground +0.9V to +3.6V Supply Voltage. Bypass this pin to GND with a ≥10µF capacitor. Ground. Should be the starpoint of CIN and COUT. Inductor. The drain of the internal N-channel MOSFET. Note: This pin is high impedance in shutdown. Shutdown Disconnect Switch Out. Disconnects the input from the output during shutdown. Ground +5.5 to +42V Output Voltage. This pin also powers the AS1343 after startup. Bypass this pin to GND with a ≥4.7µF capacitor. Feedback Pin. Feedback input to the gm error amplifier. Connect a resistor divider tap to this pin. The output voltage can be adjusted from 5.5V to 42V by: VOUT = 1.25V[1 + (R1/R2)] 2 3 4 5 6 7 8 9 10 POK GND VCC PGND LX SWOUT GND VOUT FB www.austriamicrosystems.com Revision 1.04 2 - 17 AS1343 Datasheet - A b s o l u t e M a x i m u m R a t i n g s 5 Absolute Maximum Ratings Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Electrical Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 2. Absolute Maximum Ratings Parameter VCC, EN, SWOUT, POK, FB to GND VOUT, LX to GND Thermal Resistance ΘJA ESD Latch-Up Operating Temperature Range Storage Temperature Range Junction Temperature -200 -40 -65 36.7 2.5 +150 +85 +150 125 Min Max 5 45 Units V ºC/W kV mA ºC ºC ºC The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/JEDEC J-STD-020D “Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices”. The lead finish for Pb-free leaded packages is matte tin (100% Sn). on PCB HBM MIL-Std. 883E 3015.7 methods @25°C, JEDEC 78 Comments Package Body Temperature +260 ºC www.austriamicrosystems.com Revision 1.04 3 - 17 AS1343 Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s 6 Electrical Characteristics VCC = EN = 3.6V, TAMB = -40 to +85ºC (unless otherwise specified). Typ values are at TAMB = +25ºC. Table 3. Electrical Characteristics Symbol Parameter Minimum Start-Up Voltage VCC VOUT IQ ISHDN ΔVLNR ΔVLDR η VFB IFB Supply Voltage Output Voltage Range Quiescent Current Shutdown Current VCC Line Regulation Load Regulation Efficiency Feedback Voltage Feedback Input Bias Current VFB = 1.3V VOUT = 6V, VFB=1.3V EN = GND, TAMB = +25ºC EN = GND VOUT = 15V, ILOAD = 1mA, VCC = 1.8 to 3.6V VOUT = 15V, ILOAD = 0 to 20mA L1 = 6.8µH, VOUT = 12V, ILOAD = 50mA 1.225 0.05 0.01 85 1.25 1 1.275 100 Condition VOUT = 12V, ILOAD = 1mA 0.9 5.5 22 0.02 Min Typ 0.95 Max 1 3.6 42 30 1 3 Unit V V V µA µA µA %/V %/mA % V nA DC-DC Switches ILX(MAX) RLX RP_ON ILX_LEAK IP_LEAK Control Inputs VIH EN Input Threshold VIL IEN POK Output VOL POK Output Low Voltage POK Output High Leakage Current POK Threshold Oscillator fCLK Oscillator Frequency Maximum Duty Cycle 0.85 90 1 95 1.15 MHz % POK sinking 1mA POK = 3.6V Falling edge, referenced to VOUT(NOM) 87 0.01 1 90 0.2 500 93 V nA % EN Input Current VEN = 0 to 3.6V 1 0.9V ≤ VCC ≤ 3.6V 0.8 x VCC 0.2 x VCC LX Switch Current Limit NMOS Switch OnResistance PMOS Switch OnResistance LX Leakage Current Switch Leakage Current ILX = 100mA ISWout = -100mA VLX = 42V P-channel 1.45 0.9 0.3 15 10 1.5 Ω 1.0 nA A V nA www.austriamicrosystems.com Revision 1.04 4 - 17 AS1343 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s 7 Typical Operating Characteristics Parts used for measurments: 6.8µH (MOS6020-682) Inductor, 10µF (GRM21BR60J106KE19) CIN and 4.7µF (GRM32ER71H475KA88) COUT, (PMEG4010BEA) D1; Figure 3. Efficiency vs. Output Current; VOUT = 6V 90 80 70 Figure 4. Efficiency vs. Output Current; VOUT = 12V 90 80 70 Efficiency (%) 60 50 40 30 20 10 0 0.1 1 10 100 Vi n = 1.5V Vi n = 2V Vi n = 3V Vi n = 3.6V Efficiency (%) 60 50 40 30 20 10 0 0.1 1 10 100 Vi n = 1.5V Vi n = 2V Vi n = 3V Vi n = 3.6V Output Voltage (mA) Figure 5. Efficiency vs. Output Current; VOUT = 18V 90 80 70 Output Current (mA) Figure 6. Efficiency vs. Output Current; VOUT = 24V 90 80 70 Efficiency (%) 60 50 40 30 20 10 0 0.1 1 10 100 Vi n = 1.5V Vi n = 2V Vi n = 3V Vi n = 3.6V Efficiency (%) 60 50 40 30 20 10 0 0.1 1 10 100 Vi n = 2V Vi n = 3V Vi n = 3.6V Output Current (mA) Figure 7. Efficiency vs. Input Voltage; VOUT = 12V 90 80 70 Output Current (mA) Figure 8. Efficiency vs. Input Voltage; IOUT = 10mA 90 80 70 Efficiency (%) 60 50 40 30 20 10 0 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 3.6 Iout = 1mA Iout = 10mA Iout = 50mA Iout = 100mA Efficiency (%) 60 50 40 30 20 10 0 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 3.6 Vout = 5.5V Vout = 10V Vout = 12V Vout = 15V Input Voltage (V) www.austriamicrosystems.com Revision 1.04 Input Voltage (V) 5 - 17 AS1343 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s Figure 9. Output Voltage vs. Temperature; VOUT=18V 18.2 no l oad Iout = 10mA Iout = 20mA Iout = 50mA Figure 10. Output voltage vs. Input Voltage; VOUT=12V, (line regulation) 13 Iout = 1mA Iout = 10mA Iout = 50mA Iout = 100mA Output Voltage (V) 18 Output Voltage (V) 0 15 30 45 60 75 90 18.1 12.5 12 17.9 11.5 17.8 -45 -30 -15 11 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 3.6 Temperature (°C) Figure 11. Output Voltage vs. Load Current; VOUT=12V, VIN=1.5V, (load regualtion) 12.5 12.4 Input Voltage (V) Figure 12. Maximum Output current vs. Input Voltage; VOUT = 12, 15, 18, 24, 36V 300 Vout = 12V Vout = 15V Vout = 18V Output Current (mA) 12.3 Output Voltage (V) . Vout = 24V Vout = 36V 12.2 12.1 12 11.9 11.8 11.7 11.6 11.5 0 10 20 30 200 100 0 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 3.6 Output Current (mA) Figure 13. Maximum Output current vs. VOUT; VCC = 1.5V, 3V 400 Vi n = 1.5V Vi n = 3V Input Voltage (V) Figure 14. Start-Up Voltage vs. Output Current; VCC = 0.5V to 3.6V, (95% Voutnom) 3.6 3.3 3 Output Current (mA) Start-Up Voltage (V) 300 2.7 2.4 2.1 1.8 1.5 1.2 0.9 0.6 0.3 Vout = 5.5V Vout = 15V Vout = 24V Vout = 12V Vout = 18V Vout = 36V 200 100 0 5 15 25 35 45 0 0 10 20 30 40 50 60 70 80 90 100 Output Voltage (V) www.austriamicrosystems.com Revision 1.04 Output Current (mA) 6 - 17 AS1343 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s Figure 15. Shutdown Current vs. VCC 0.1 0.09 Figure 16. Shutdown Current vs. Temperature 1.5 Shutdown Current (µA) . 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 3.6 Shutdown Current (µA) . 1 0.5 0 -45 -30 -15 0 15 30 45 60 75 90 Input Voltage (V) Temperature (°C) Figure 17. Switching Frequency vs. Temperature 1.1 Figure 18. Feedback Voltage vs. Temperature 1.3 Switching Frequency (MHz) . 1.05 Feedback Voltage (V) . 0 15 30 45 60 75 90 1.275 1 1.25 0.95 1.225 0.9 -45 -30 -15 1.2 -45 -30 -15 0 15 30 45 60 75 90 Temperature (°C) Temperature (C°) Figure 19. Quiescent Current vs. VCC 22 Figure 20. Startup Waveform; VIN = 3.6V Quiescent Current (µA) . 21.5 20.5 500mA/DIV 2ms/Div LX 20 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 3.6 Input Voltage (V) www.austriamicrosystems.com Revision 1.04 VOUT 21 10V/Div 2V/Div EN 7 - 17 AS1343 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s Figure 21. Transient Line Regulation; VOUT = 18V, ILOAD = 1mA Figure 22. Transient Line Regulation; VOUT = 18V, ILOAD = 20mA 2.5V 3.0V 200mV/DIV 500µs/Div 500µs/Div Figure 23. Output Voltage Ripple; VOUT = 18V, IOUT = 1mA Figure 24. Output Voltage Ripple; VOUT = 18V, IOUT = 20mA VIN = 3.6V VIN = 3.6V VIN = 3.0V 200mV/Div VOUT VOUT VIN = 3.0V 200mV/Div VIN = 1.5V 1µs/Div 5ms/Div 1mA 20mA 200mV/Div VIN = 1.5V 1µs/Div Figure 25. Load Transient Response ON; VCC = 3V, VOUT = 18V Figure 26. Load Transient Response OFF; VCC = 3V, VOUT = 18V 200mV/Div VOUT(AC) 1mA 20mA IOUT 5ms/Div www.austriamicrosystems.com Revision 1.04 IOUT VOUT(AC) 200mV/DIV VOUT(AC) VOUT(AC) 2.5V 3.0V VIN VIN 8 - 17 AS1343 Datasheet - D e t a i l e d D e s c r i p t i o n 8 Detailed Description The AS1343 features a current limiting circuitry, a fixed-frequency PWM architecture, power-OK circuitry, thermal protection, and an automatic powersave mode in a tiny package, and maintains high efficiency at light loads. Figure 27. AS1343 - Block Diagram with Shutdown Disconnect Switch L1 6.8µH 7 Input Voltage 0.9V to 3.6V 4 VCC CIN 10µF PWM Control Sync Drive Control 1 MHz Spread Spectrum Ramp Generator + PWM – Comp – 1 EN Shutdown Control Slope Compensator Σ SWOUT 0.3Ω PMOS 2 POK 6 LX – VOUT Good + 0.9Ω NMOS 1.13V 9 VOUT Output Voltage 5.5V to 42V D1 Current Sense R1 AS1343 VC RC – gm Error Amp + 10 FB COUT 4.7µF Shutdown Powersave Operation Control CP2 CC 1.25V Ref R2 Powersave 3 GND 8 GND 5 PGND Automatic powersave mode regulates the output and also reduces average current flow into the device, resulting in high efficiency at light loads. When the output increases sufficiently, the powersave comparator output remains high, resulting in continuous operation. For each oscillator cycle, the power switch is enabled. A voltage proportional to switch current is added to a stabilizing ramp and the resulting sum is delivered to the positive terminal of the PWM comparator. The error amplifier compares the voltage at FB with the internal 1.25V reference and generates an error signal (VC). When VC is below the powersave mode threshold voltage the automatic powersave-mode is activated and the hysteretic comparator disables the power circuitry, with only the low-power circuitry still active (total current consumption is minimized). When a load is applied, VFB decreases; VC increases and enables the power circuitry and the device starts switching. In light loads, the output voltage (and the voltage at FB) will increase until the powersave comparator disables the power circuitry, causing the output voltage to decrease again. This cycle is repeated resulting in low-frequency ripple at the output. POK Function The POK output indicates if the output voltage is within 90% of the nominal voltage level. As long as the output voltage is within regulation the open-drain POK output is high impedance. The POK output can be tied to any external voltage up to a maximum of 5V via a pull-up resistance R3 (see Typical Application on page 10). If the output voltage drops below 90% of the nominal voltage the POK pin is pulled to GND. Note: It is important to consider that in shutdown mode the POK output is pulled to VCC in order to save current. www.austriamicrosystems.com Revision 1.04 9 - 17 AS1343 Datasheet - A p p l i c a t i o n I n f o r m a t i o n 9 Application Information Shutdown and Output Discharge A logic low on the EN pin shuts down the AS1343 and a logic high on the EN pin powers on the device. In shutdown mode the supply current drops to below 3µA and the POK pin is set to high impedance to maximize battery life. When the battery disconnect switch is used, the battery is disconnected from the output and the output is discharged down to 0V. The time for fully discharging the output depends on the COUT and on the load. Note: Pin EN should not be left floating. If the shutdown feature is not used, connect EN to VCC. The output will be discharged during shutdown but the output also must be fully discharged before the device is enabled again. Battery Disconnect The AS1343 has an integrated PMOS switch that can be used to disconnect the battery during shutdown. The operation voltage of this switch is limited to 3.6V. When EN is high, the switch is closed and supplies the inductor. Due to the RON resistance the efficiency is slightly lower if the battery disconnect switch is used. PLOSS = IIN² x RON (EQ 1) Setting Output Voltage Output voltage can be adjusted by connecting a voltage divider between pins VOUT and FB (see Figure 28). Figure 28. Typical Application L1 6.8µH 7 VCC = 0.9V to 3.6V C1 10µF 4 VCC R3 100kΩ 9 2 POK On Off 1 EN 5 PGND 3, 8 GND VOUT SWOUT 6 LX D1 VOUT = 18V COUT 4.7µF AS1343 10 FB R1 2.2MΩ R2 165kΩ The output voltage can adjusted by selecting different values for R1 and R2. For R2, select a value between 10k and 200kΩ. Calculate R1 by: ⎛ V OUT ⎞ R 1 = R 2 ⋅ ⎝ -------------- – 1⎠ V FB Where: (EQ 2) VOUT = 5.5V to 42V, VFB = 1.25V; VOUT > VIN The input bias current of FB has a maximum value of 100nA which allows for large-value resistors. For less than 1% error, the current through R2 should be 100 times the feedback input bias current (IFB). That’s why the feeback current can be neglected in the calculation of VOUT. Note: For the optimal operation condition the following ratio between VOUT and VIN should be used: V OUT ÷ V IN ≤ 12 (EQ 3) www.austriamicrosystems.com Revision 1.04 10 - 17 AS1343 Datasheet - A p p l i c a t i o n I n f o r m a t i o n LED Power Supply Application The AS1343 can also be used for driving LEDs. Just simply connect the LEDs between the pins VOUT and FB. (see Figure 29). Figure 29. LED Supply Application L1 6.8µH 7 VCC = 0.9V to 3.6V C1 10µF 4 VCC R3 100kΩ 9 2 POK On Off 1 EN 5 PGND 3, 8 GND VOUT SWOUT 6 LX D1 COUT 4.7µF AS1343 10 FB R2 100Ω ILED The output voltage is adjusted automatically to the required voltage of the LEDs. This voltage depends on the forward voltage (VF) of the used LEDs and the Feeback Voltage VFB. Calculate VOUT by: V OUT = V F ( I LED ) × n + V FB (EQ 4) Note: The brightness of the LEDs can directly be adjusted by setting the current ILED via the corresponding R2. Calculate R2 by: V FB I LED = --------R2 Where: (EQ 5) VFB = 1.25V n .... number of LEDs Thermal Protection To protect the device from short circuit or excessive power dissipation of the auxiliary NPNs, the integrated thermal protection switches off the device when the junction temperature (TJ) reaches 140ºC (typ). When TJ decreases to approximately 135ºC, the device will resume normal operation. If the thermal overload condition is not corrected, the device will switch on and off while maintaining TJ within the range between 135 and 140ºC. www.austriamicrosystems.com Revision 1.04 11 - 17 AS1343 Datasheet - A p p l i c a t i o n I n f o r m a t i o n Inductor Selection For the external inductor, a 4.7µH or 6.8µH inductor will usually suffice. Minimum inductor size is dependant on the desired efficiency and output current. Inductors with low core losses and small DCR at 1MHz are recommended. It’s also recommendet to choose an inductor which can handle at least 1.2A without saturating. The MOS6020 is a very good choice because the DCR is quite small and the saturation current exeeds 1.2A. For space limiting applications and input currents below 650mA the EPL2014 can be selected. Efficiency losses due to higher DCR should be considered. (see Figure 30 and Figure 31) Table 4. Recommended Inductors Part Number L DCR ISAT @ 20% drop Dimensions (L/W/T) Manufacturer Coilcraft www.coilcraft.com EPL2014-472MLC LPS3015-472MLC LPS4018-682MLC LPS5030-682ML_ MOS6020-682MLC MOS6020-472MLC 4.7µH 4.7µH 6.8µH 6.8µH 6.8µH 4.7µH 0.231Ω 0.200Ω 0.150Ω 0.099Ω 0.078Ω 0.050Ω 0.65A 1.2A 1.3A 1.7A 1.56A 1.82A 2.2x2.0x1.4mm 3.1x3.1x1.5mm 4.1x4.1x1.8mm 4.88x4.88x3.0mm 6.0x6.8x2.4mm 6.0x6.8x2.4mm Note: For the Efficiency measurements in Figure 30 and Figure 31 a MBR0540 diode was used for D1. Figure 30. Efficiency Comparison of different Inductors; VIN = 3V, VOUT = 18V 90 80 70 Figure 31. Efficiency Comparison of different Inductors; VIN = 3.6V, VOUT = 18V 90 80 70 Efficiency (%) 60 50 40 30 20 10 0 0.1 1 10 100 MOS6020 6.8µH LPS5030 6.8µH LPS4018 6.8µH MOS6020 4.7µH LPS3015 4.7µH EPL2014 4.7µH Efficiency (%) 60 50 40 30 20 10 0 0.1 1 10 100 MOS6020 6.8µH LPS5030 6.8µH LPS4018 6.8µH MOS6020 4.7µH LPS3015 4.7µH EPL2014 4.7µH Output Current (mA) Output Current (mA) www.austriamicrosystems.com Revision 1.04 12 - 17 AS1343 Datasheet - A p p l i c a t i o n I n f o r m a t i o n Capacitor Selection A 10µF capacitor is recommend for CIN as well as a 4.7µF for COUT. Small-sized ceramic capacitors are recommended. X5R and X7R ceramic capacitors are recommend as they retain capacitance over wide ranges of voltages and temperatures. Output Capacitor Selection Low ESR capacitors should be used to minimize VOUT ripple. Multi-layer ceramic capacitors are recommended since they have extremely low ESR and are available in small footprints. A 4.7 to 10µF output capacitor is sufficient for most applications. Larger values up to 22µF may be used to obtain extremely low output voltage ripple and improve transient response. The rated voltage of the capacitor should not be lower than the output voltage. Table 5. Recommended Output Capacitors Part Number C TC Code Rated Voltage Dimensions (L/W/T) Manufacturer Murata www.murata.com GRM32DR71H335KA88B GRM32ER71H475KA88 GRM31CR61E106KA12 C3225X5R1H335K C3216X5R1E475K C3225X5R1E106K 3.3µF 4.7µF 10µF 3.3µF 4.7µF 10µF X7R X7R X5R X5R X5R X5R 50V 50V 25V 50V 25V 25V 1210 1210 1206 1210 1206 1210 TDK www.tdk.com Input Capacitor Selection Low ESR input capacitors reduce input switching noise and reduce the peak current drawn from the battery. Ceramic capacitors are recommended for input decoupling and should be located as close to the device as is practical. A 10µF input capacitor is sufficient for most applications. Larger values may be used for a better stabilization of the supply voltage. Table 6. Recommended Input Capacitors Part Number C TC Code Rated Voltage Dimensions (L/W/T) Manufacturer Murata www.murata.com GRM21BR60J106KE19 GRM188R60J106ME47 GRM21BR60J226ME39 C1608X5R0J106MB C2012X5R0J226M 10µF 10µF 22µF 10µF 22µF X5R X5R X5R X5R X5R 6.3V 6.3V 6.3V 6.3V 6.3V 0805 0603 0805 0603 0805 TDK www.tdk.com www.austriamicrosystems.com Revision 1.04 13 - 17 AS1343 Datasheet - A p p l i c a t i o n I n f o r m a t i o n Diode Selection A Schottky diode must be used to carry the output current into the Cout and load during the NMOS switch-off time. Note: Do not use ordinary rectifier diodes, since the slow recovery times will compromise efficiency. The MBR0520 is a good choice because of the very low forward voltage and the extremly fast switching. If the output voltage exceeds 20V the use of the PMEG4005 or the MBR0540 (40V Schottky diodes) is recommended. These diodes are designed to handle an average forward current of 500mA. In applications with higher loads, the PMEG4010 or the MBRM140 should be used, due to the rated average forward current of 1A. Table 7. Recommended Diodes Part Number Reverse Voltage Forward Current Package Manufacturer MCC www.mccsemi.com MBR0540 MBR0520 PMEG4005 PMEG4010 MBRM140 40V 20V 40V 40V 40V 0.5A 0.5A 0.5A 1A 1A SOD123 SOD123 SOD123 SOD123 SOD123 Philips www.nxp.com ON Semiconductor www.onsemi.com Figure 32. Efficiency Comparison of different Diodes; VIN = 3V, VOUT = 18V, L1 = 6.8µH 90 80 70 Figure 33. Efficiency Comparison of different Diodes; VIN = 3.6V, VOUT = 18V, L1 = 6.8µH 90 80 70 Efficiency (%) 60 50 40 30 20 10 0 0.1 1 10 100 PMEG4010 MBR0540 MBR0520 PMEG4005 Efficiency (%) 60 50 40 30 20 10 0 0.1 1 10 100 PMEG4010 MBR0540 MBR0520 PMEG4005 Output Current (mA) Output Current (mA) www.austriamicrosystems.com Revision 1.04 14 - 17 AS1343 Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s 10 Package Drawings and Markings The devices are available in a TDFN-10 3x3mm package. Figure 34. TDFN-10 3x3mm Package D D2 SEE DETAIL B B A L E2/2 2x aaa C PIN 1 INDEX AREA (D/2 xE/2) D2/2 E2 K N N-1 e (ND-1) X e b ddd bbb C CAB BTM VIEW PIN 1 INDEX AREA (D/2 xE/2) aaa C 2x TOP VIEW e DETAIL B Terminal Tip ccc C E A3 C SEATING PLANE 0.08 C A Datum A or B ODD TERMINAL SIDE Symbol A A1 A3 L1 L2 aaa bbb ccc ddd eee ggg Notes: Min 0.70 0.00 Typ 0.75 0.02 0.20 REF Max 0.80 0.05 0.03 0.15 0.10 0.10 0.05 0.08 0.10 0.15 0.13 Notes 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 Symbol D BSC E BSC D2 E2 L θ K b e N ND Min Typ 3.00 3.00 A1 SIDE VIEW Max 1.60 1.35 0.30 0º 0.20 0.18 0.40 2.50 1.75 0.50 14º 0.30 0.25 0.50 10 5 Notes 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2, 5 1, 2 1, 2, 5 1. Figure 34 is shown for illustration only. 2. All dimensions are in millimeters; angles in degrees. 3. Dimensioning and tolerancing conform to ASME Y14.5 M-1994. 4. N is the total number of terminals. 5. The terminal #1 identifier and terminal numbering convention shall conform to JEDEC 95-1, SPP-012. Details of terminal #1 identifier are optional, but must be located within the zone indicated. The terminal #1 identifier may be either a mold or marked feature. 6. Dimension b applies to metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 7. ND refers to the maximum number of terminals on side D. 8. Unilateral coplanarity zone applies to the exposed heat sink slug as well as the terminals www.austriamicrosystems.com Revision 1.04 15 - 17 AS1343 Datasheet - O r d e r i n g I n f o r m a t i o n 11 Ordering Information The device is available as the standard products shown in Table 8. Table 8. Ordering Information Model Marking Description Delivery Form Package AS1343A-BTDT-10 ASQN 42V, Micropower, DC-DC Boost Converter, Automatic Power Save, 1MHz Tape and Reel TDFN-10 3x3mm Note: All products are RoHS compliant and Pb-free. Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect For further information and requests, please contact us mailto:sales@austriamicrosystems.com or find your local distributor at http://www.austriamicrosystems.com/distributor www.austriamicrosystems.com Revision 1.04 16 - 17 AS1343 Datasheet Copyrights Copyright © 1997-2009, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com Revision 1.04 17 - 17