PD100-003-0XX

PD100 100μm InGaAs Photodiode FEATURES • • • • • Planar Structure High Responsivity Low Dark Current Dielectric Passivation 100% Purge Burn-in PD100-003-0xx Ceramic Sub-Mount PD100-003-1xx TO can Package APPLICATIONS • • • Optical Communication Systems Test and Measurement Sensing PD100-003-3xx SC/APC Pigtail PD100-003-5xx FC Receptacle PRODUCT DESCRIPTION The PD100 is an InGaAs photodiode with a photosensitive region 100μm in diameter. It is intended for use in high speed, low noise communication systems (up to 1.5Gb/s data rates) as well as applications in test and measurement and other optical power sensing devices. The large active area allows the use of multimode fiber. Reliability is assured by hermetic sealing and 100% purge burn-in (200°C, 15 hours, Vr = 20V). The device can be assembled on a ceramic submount or in a TO can. It can be pigtailed with SC, FC or ST connectors (UPC or APC). It can also be mounted in an SC, ST of FC receptacle. Custom packages are an option. ELECTRICAL CHARACTERISTICS Table 1: Electrical Specifications PARAMETER Dark Current (ID) Capacitance (Ceramic sub-mount) (1) Capacitance (Receptacle, Pigtail, TO can) (1) Responsivity at 1310nm (Ceramic sub-mount) Responsivity at 1550nm (Ceramic sub-mount) Responsivity at 1310nm (Receptacle, Pigtail, TO can) Responsivity at 1550nm (Receptacle, Pigtail, TO can) 3dB bandwidth (50Ω) (Ceramic sub-mount) (1) 3dB bandwidth (50Ω) (Receptacle, Pigtail, TO can) (1) Optical Return Loss (Pigtail using SMF-28) Optical Return Loss (Receptacle, APC connector) Operating voltage (1) 5V bias voltage MIN 0.80 0.85 0.80 0.85 2400 2000 50 40 TYP 0.2 1.0 1.2 0.90 0.95 0.85 0.90 2700 2200 55 45 5 MAX 2.0 1.1 1.3 20 UNIT nA pF pF A/W A/W A/W A/W MHz MHz dB dB V PD100 Table 2: Absolute Maximum Ratings PARAMETER Forward Current Reverse Current Reverse Voltage Optical input power Operating Case Temperature Storage Temperature Soldering temperature (10 seconds) MIN -40 -40 MAX 5 500 30 5 +85 +85 +250 UNIT mA μA V mW ºC ºC ºC Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. PACKAGE DIMENSIONS – PD100-003-100 and PD100-003-105 Dimensions: INCHES [mm] ORDERING INFORMATION Table 3: Standard Part Number PD100-003-100 PD100-003-105 Options TO46, 3pin, non AR coated, gold plated lens cap TO46, 3pin, non AR coated, gold plated flat window cap Table 4: Custom Part Number PD100-003-0xx PD100-003-1xx PD100-003-3xx PD100-003-5xx Options Custom defined size and electrical layout. Package: TO46, TO56, 2 or 3 pin. Cap: Window or lens. AR or Non-AR coated. Gold or nickel plated. Pigtailed: TO46, 2 or 3 pin. Fiber length, 0.5 meter, 1.0 meter Fiber type: Multimode, single mode (SMF-28) or custom supplied Connector Type: SC, ST or FC. APC or UPC Receptacle, 2 or 3 pin. SC, ST or FC aligned Please contact Anadigics for the specific part number and pinout that suits your needs ANADIGICS, Inc. 829 Flynn Road Camarillo, California 93012, U.S.A. Tel: +1 (805) 445-4500 Fax: +1 (805) 445-4502 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibility for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. Rev 1.0 2