PD300-003-3XX

PD300 300μm InGaAs Photodiode FEATURES • • • • Planar Structure Dielectric Passivation 100% Purge Burn-in High Responsivity PD300-003-0xx Ceramic Sub-Mount PD300-003-1xx TO can Package APPLICATIONS • • • • Communications Test and Measurement Sensing Optical Power Monitors PD300-003-3xx SC/APC Pigtail PD300-003-5xx FC Receptacle PRODUCT DESCRIPTION The PD300 is an InGaAs photodiode with a photosensitive region 300μm in diameter. It is intended for use in moderate speed, low noise communication systems (up to 300Mb/s data rates) as well as applications in test and measurement and other optical power sensing devices. The large active area allows the use of multimode fiber. Reliability is assured by hermetic sealing and 100% purge burn-in (200°C, 15 hours, Vr = 15V). The device can be assembled on a ceramic submount or in a TO can. It can be pigtailed with SC, FC or ST connectors (UPC or APC). It can also be mounted in an SC, ST of FC receptacle. Custom packages are an option. ELECTRICAL CHARACTERISTICS Table 1: Electrical Specifications PARAMETER Dark Current (ID) Capacitance (Ceramic sub-mount) (1) Capacitance (Receptacle, Pigtail, TO can) (1) Responsivity at 1310nm (Ceramic sub-mount) Responsivity at 1550nm (Ceramic sub-mount) Responsivity at 1310nm (Receptacle, Pigtail, TO can) Responsivity at 1550nm (Receptacle, Pigtail, TO can) 3dB bandwidth (50Ω) (Ceramic sub-mount) (1) 3dB bandwidth (50Ω) (Receptacle, Pigtail, TO can) (1) Optical Return Loss (Pigtail using SMF-28) Optical Return Loss (Receptacle, APC connector) Operating voltage (1) 5V bias voltage MIN 0.80 0.85 0.80 0.85 630 600 50 40 TYP 0.5 4.0 4.2 0.90 0.95 0.85 0.90 660 630 55 45 5 MAX 5.0 4.2 4.4 15 UNIT nA pF pF A/W A/W A/W A/W MHz MHz dB dB V PD300 Table 2: Absolute Maximum Ratings PARAMETER Forward Current Reverse Current Reverse Voltage Optical input power Operating Case Temperature Storage Temperature Soldering temperature (10 seconds) MIN -40 -40 MAX 25 5000 20 5 +85 +85 +250 UNIT mA μA V mW ºC ºC ºC Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. PACKAGE DIMENSIONS – PD300-003-100 and PD300-003-105 Dimensions: INCHES [mm] ORDERING INFORMATION Table 3: Standard Part Number PD300-003-100 PD300-003-105 Options TO46, 3pin, non AR coated, gold plated lens cap TO46, 3pin, non AR coated, gold plated flat window cap Table 4: Custom Part Number PD300-003-0xx PD300-003-1xx PD300-003-3xx PD300-003-5xx Options Custom defined size and electrical layout. Package: TO46, TO56, 2 or 3 pin. Cap: Window or lens. AR or Non-AR coated. Gold or nickel plated. Pigtailed: TO46, 2 or 3 pin. Fiber length, 0.5 meter, 1.0 meter Fiber type: Multimode, single mode (SMF-28) or custom supplied Connector Type: SC, ST or FC. APC or UPC Receptacle, 2 or 3 pin. SC, ST or FC aligned Please contact Anadigics for the specific part number and pinout that suits your needs ANADIGICS, Inc. 829 Flynn Road Camarillo, California 93012, U.S.A. Tel: +1 (805) 445-4500 Fax: +1 (805) 445-4502 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibility for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. Rev 1.0 2