AAT1146IJS-1.875-T1

PRODUCT DATASHEET AAT1146 SwitchRegTM General Description The AAT1146 SwitchReg is a 1.4MHz step-down converter with an input voltage range of 2.7V to 5.5V and output voltage as low as 0.6V. It is optimized to react quickly to a load variation. The AAT1146 is available in fixed voltage versions with internal feedback and a programmable version with external feedback resistors. It can deliver 400mA of load current while maintaining a low 27μA no load quiescent current. The 1.4MHz switching frequency minimizes the size of external components while keeping switching losses low. The AAT1146 is designed to maintain high efficiency throughout the operating range, which is critical for portable applications. The AAT1146 is available in the Pb-free, space-saving 2.0x2.1mm SC70JW-8 and SOT23-5 packages and is rated over the -40°C to +85°C temperature range. Fast Transient 400mA Step-Down Converter Features • • • • • • • • • • • • • • VIN Range: 2.7V to 5.5V VOUT Fixed or Adjustable from 0.6V to VIN 27μA No Load Quiescent Current Up to 98% Efficiency 400mA Max Output Current 1.4MHz Switching Frequency 120μs Soft Start Fast Load Transient Over-Temperature Protection Current Limit Protection 100% Duty Cycle Low-Dropout Operation 1.0V Output2 From Enable to Output Regulation TA = 25°C 1 591 250 1.0 150 1.4 140 15 2.0 0.1 600 609 0.2 100 1.8 -3.0 0.6 27 +3.0 VIN 70 1.0 Fast Transient 400mA Step-Down Converter Typ Max 5.5 2.7 Units V V mV V % V μA μA mA Ω Ω μA %/V mV μA kΩ μs MHz °C °C V V μA Step-Down Converter VIN Input Voltage VUVLO VOUT VOUT IQ ISHDN ILIM RDS(ON)H RDS(ON)L ILXLEAK ΔVLinereg VOUT IOUT ROUT TS FOSC TSD THYS EN VEN(L) VEN(H) IEN UVLO Threshold Output Voltage Tolerance Output Voltage Range Quiescent Current Shutdown Current P-Channel Current Limit High Side Switch On Resistance Low Side Switch On Resistance LX Leakage Current Line Regulation Out Threshold Voltage Accuracy Out Leakage Current Out Impedance Start-Up Time Oscillator Frequency Over-Temperature Shutdown Threshold Over-Temperature Shutdown Hysteresis Enable Threshold Low Enable Threshold High Input Low Current 0.6 VIN = VOUT = 5.5V 1.4 -1.0 1.0 1. The AAT1146 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2. The AAT1146 fixed output versions have the output set to different voltages. 4 www.analogictech.com 1146.2008.06.1.6 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Typical Characteristics Efficiency vs. Load (VOUT = 1.8V; L = 4.7μH) 100 90 1.0 Fast Transient 400mA Step-Down Converter DC Regulation (VOUT = 1.8V) VIN = 2.7V Output Error (%) 0.5 Efficiency (%) 80 70 60 50 0.1 VIN = 3.6V VIN = 4.2V VIN = 4.2V 0.0 -0.5 VIN = 3.6V VIN = 2.7V 1 10 100 1000 -1.0 0.1 1 10 100 1000 Output Current (mA) Output Current (mA) Efficiency vs. Load (VOUT = 2.5V; L = 6.8μH) 100 1.0 DC Regulation (VOUT = 2.5V) VIN = 2.7V Output Error (%) 90 VIN = 4.2V 0.5 Efficiency (%) 80 70 60 50 0.1 VIN = 5.0V VIN = 4.2V VIN = 3.6V VIN = 5.0V 0.0 -0.5 VIN = 3.6V VIN = 3.0V -1.0 1 10 100 1000 0.1 1 10 100 1000 Output Current (mA) Output Current (mA) Efficiency vs. Load (VOUT = 3.3V; L = 6.8μH) 100 100 Efficiency vs. Load (VOUT = 3.3V; L = 6.8μH) VIN = 3.6V 90 VIN = 3.6V 90 Efficiency (%) 80 70 60 50 0.1 VIN = 4.2V VIN = 5.0V Efficiency (%) 80 70 60 50 0.1 VIN = 4.2V VIN = 5.0V 1 10 100 1000 1 10 100 1000 Output Current (mA) Output Current (mA) 1146.2008.06.1.6 www.analogictech.com 5 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Typical Characteristics Soft Start (VIN = 3.6V; VOUT = 1.8V; IOUT = 400mA) Enable and Output Voltage (top) (V) 5.0 4.0 3.0 2.0 1.0 0.0 -1.0 -2.0 -3.0 -4.0 -5.0 1.6 0.40 0.30 Fast Transient 400mA Step-Down Converter Line Regulation (VOUT = 1.8V) VEN VO 1.4 1.0 0.8 0.6 0.4 0.2 Accuracy (%) 1.2 0.20 0.10 0.00 -0.10 -0.20 -0.30 -0.40 2.5 3.0 3.5 IOUT = 10mA Inductor Current (bottom) (A) IOUT = 1mA IOUT = 400mA IL 0.0 -0.2 -0.4 4.0 4.5 5.0 5.5 6.0 Time (100μs/div) Input Voltage (V) Output Voltage Error vs. Temperature (VIN = 3.6V; VO = 1.8V; IOUT = 400mA) 2.0 15.0 12.0 9.0 Switching Frequency vs. Temperature (VIN = 3.6V; VOUT = 1.8V) Output Error (%) Variation (%) 1.0 6.0 3.0 0.0 -3.0 -6.0 -9.0 -12.0 -15.0 -40 0.0 -1.0 -2.0 -40 -20 0 20 40 60 80 100 -20 0 20 40 60 80 100 Temperature (°C) Temperature (°C) Frequency vs. Input Voltage 2.0 No Load Quiescent Current vs. Input Voltage 50 Frequency Variation (%) 1.0 0.0 -1.0 VOUT = 1.8V Supply Current (μA) 45 40 35 30 25 20 15 10 85°C 25°C VOUT = 2.5V -2.0 -3.0 -4.0 2.7 3.1 3.5 3.9 VOUT = 3.3V -40°C 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 4.3 4.7 5.1 5.5 Input Voltage (V) Input Voltage (V) 6 www.analogictech.com 1146.2008.06.1.6 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Typical Characteristics P-Channel RDS(ON) vs. Input Voltage 750 700 650 750 700 Fast Transient 400mA Step-Down Converter N-Channel RDS(ON) vs. Input Voltage RDS(ON) (mΩ) RDS(ON) (mΩ) 120°C 100°C 650 600 550 500 450 400 350 300 25°C 120°C 100°C 600 550 500 450 400 350 300 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 25°C 85°C 85°C 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Input Voltage (V) Input Voltage (V) Load Transient Response (1mA to 300mA; VIN = 3.6V; VOUT = 1.8V; C1 = 10μF; CFF = 100pF) 2.0 1.9 1.90 1.85 Load Transient Response (300mA to 400mA; VIN = 3.6V; VOUT = 1.8V; C1 = 4.7μF) Load and Inductor Current (200mA/div) (bottom) Load and Inductor Current (200mA/div) (bottom) VO IO VO IO IL Output Voltage (top) (V) 1.7 300mA 1mA Output Voltage (top) (V) 1.8 1.80 1.75 400mA 300mA 0.4 0 IL Time (50μs/div) 0.3 0.2 0.1 Time (50μs/div) Load Transient Response (300mA to 400mA; VIN = 3.6V; VOUT = 1.8V; C1 = 10μF) 1.90 1.85 Load Transient Response (300mA to 400mA; VIN = 3.6V; VOUT = 1.8V; C1 = 10μF; C4 = 100pF) 1.850 1.825 Load and Inductor Current (200mA/div) (bottom) Load and Inductor Current (200mA/div) (bottom) VO IO VO IO 400mA 300mA 0.4 Output Voltage (top) (V) 1.75 Output Voltage (top) (V) 1.80 1.800 1.775 400mA 300mA 0.4 IL Time (50μs/div) 0.3 0.2 0.1 IL Time (50μs/div) 0.3 0.2 0.1 1146.2008.06.1.6 www.analogictech.com 7 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Typical Characteristics Line Response (VOUT = 1.8V @ 400mA) Output Voltage (AC coupled) (top) (mV) 1.82 1.81 6.0 5.5 40 20 0 -20 -40 -60 -80 -100 -120 Fast Transient 400mA Step-Down Converter Output Ripple (VIN = 3.6V; VOUT = 1.8V; IOUT = 1mA) 0.30 VO 0.25 Inductor Current (bottom) (A) Output Voltage (top) (V) 0.20 0.15 0.10 Input Voltage (bottom) (V) 1.80 1.79 1.78 1.77 1.76 5.0 4.5 4.0 3.5 3.0 IL 0.05 0.00 -0.05 -0.10 Time (25μs/div) Time (10µs/div) Output Ripple (VIN = 3.6V; VOUT = 1.8V; IOUT = 400mA) Output Voltage (AC coupled) (top) (mV) 40 20 0 -20 -40 -60 -80 -100 -120 0.9 VO 0.8 Inductor Current (bottom) (A) 0.7 0.6 0.5 0.4 0.3 IL 0.2 0.1 Time (500ns/div) 8 www.analogictech.com 1146.2008.06.1.6 PRODUCT DATASHEET AAT1146 SwitchRegTM Functional Block Diagram OUT VIN Fast Transient 400mA Step-Down Converter See note Err Amp . DH Voltage Reference Logic LX DL EN INPUT PGND AGND Note: For adjustable version, the internal feedback divider is omitted and the OUT pin is tied directly to the internal error amplifier. Functional Description The AAT1146 is a high performance 400mA 1.4MHz monolithic step-down converter. It has been designed with the goal of minimizing external component size and optimizing efficiency over the complete load range. Apart from the small bypass input capacitor, only a small L-C filter is required at the output. Typically, a 4.7μH inductor and a 4.7μF ceramic capacitor are recommended (see table of values). The fixed output version requires only three external power components (CIN, COUT, and L). The adjustable version can be programmed with external feedback to any voltage, ranging from 0.6V to the input voltage. An addi- tional feed-forward capacitor (CFF) can also be added to the external feedback to provide improved transient response (see Figure 1). At dropout, the converter duty cycle increases to 100% and the output voltage tracks the input voltage minus the RDSON drop of the P-channel high-side MOSFET. The input voltage range is 2.7V to 5.5V. The converter efficiency has been optimized for all load conditions, ranging from no load to 400mA. The internal error amplifier and compensation provides excellent transient response, load, and line regulation. Soft start eliminates any output voltage overshoot when the enable or the input voltage is applied. 1146.2008.06.1.6 www.analogictech.com 9 PRODUCT DATASHEET AAT1146 SwitchRegTM 1 2 3 Fast Transient 400mA Step-Down Converter VIN Enable CFF 1 2 U1 AAT1146 EN OUT VIN LX PGND PGND PGND AGND 8 7 6 5 VOUT C1 10µF R1 118k L1 4.7µH R2 59k 3 4 C2 4.7µF GND GND2 LX U1 AAT1146 SC70JW-8 L1 CDRH3D16-4R7 C1 10µF 10V 0805 X5R C2 4.7µF 10V 0805 X5R Figure 1: Enhanced Transient Response Schematic. Control Loop The AAT1146 is a peak current mode step-down converter. The current through the P-channel MOSFET (high side) is sensed for current loop control, as well as short circuit and overload protection. A fixed slope compensation signal is added to the sensed current to maintain stability for duty cycles greater than 50%. The peak current mode loop appears as a voltage-programmed current source in parallel with the output capacitor. The output of the voltage error amplifier programs the current mode loop for the necessary peak switch current to force a constant output voltage for all load and line conditions. Internal loop compensation terminates the transconductance voltage error amplifier output. For fixed voltage versions, the error amplifier reference voltage is internally set to program the converter output voltage. For the adjustable output, the error amplifier reference is fixed at 0.6V. Current Limit and Over-Temperature Protection For overload conditions, the peak input current is limited. To minimize power dissipation and stresses under current limit and short-circuit conditions, switching is terminated after entering current limit for a series of pulses. Switching is terminated for seven consecutive clock cycles after a current limit has been sensed for a series of four consecutive clock cycles. Thermal protection completely disables switching when internal dissipation becomes excessive. The junction over-temperature threshold is 140°C with 15°C of hysteresis. Once an over-temperature or over-current fault conditions is removed, the output voltage automatically recovers. Under-Voltage Lockout Internal bias of all circuits is controlled via the VIN input. Under-voltage lockout (UVLO) guarantees sufficient VIN bias and proper operation of all internal circuitry prior to activation. Soft Start / Enable Soft start limits the current surge seen at the input and eliminates output voltage overshoot. When pulled low, the enable input forces the AAT1146 into a low-power, non-switching state. The total input current during shutdown is less than 1μA. 10 www.analogictech.com 1146.2008.06.1.6 PRODUCT DATASHEET AAT1146 SwitchRegTM Applications Information Inductor Selection The step-down converter uses peak current mode control with slope compensation to maintain stability for duty cycles greater than 50%. The output inductor value must be selected so the inductor current down slope meets the internal slope compensation requirements. The internal slope compensation for the adjustable and low-voltage fixed versions of the AAT1146 is 0.24A/μsec. This equates to a slope compensation that is 75% of the inductor current down slope for a 1.5V output and 4.7μH inductor. Fast Transient 400mA Step-Down Converter Input Capacitor Select a 4.7μF to 10μF X7R or X5R ceramic capacitor for the input. To estimate the required input capacitor size, determine the acceptable input ripple level (VPP) and solve for C. The calculated value varies with input voltage and is a maximum when VIN is double the output voltage. CIN = V⎞ VO ⎛ · 1- O VIN ⎝ VIN ⎠ ⎛ VPP ⎞ - ESR · FS ⎝ IO ⎠ m= 0.75 ⋅ VO 0.75 ⋅ 1.5V A = = 0.24 L 4.7μH μsec VO ⎛ V⎞ 1 · 1 - O = for VIN = 2 × VO VIN ⎝ VIN ⎠ 4 CIN(MIN) = 1 ⎛ VPP ⎞ - ESR · 4 · FS ⎝ IO ⎠ This is the internal slope compensation for the adjustable (0.6V) version or low-voltage fixed versions. When externally programming the 0.6V version to 2.5V, the calculated inductance is 7.5μH. L= 0.75 ⋅ VO = m μsec 0.75 ⋅ VO ≈ 3 A ⋅ VO A 0.24A μsec Always examine the ceramic capacitor DC voltage coefficient characteristics when selecting the proper value. For example, the capacitance of a 10μF, 6.3V, X5R ceramic capacitor with 5.0V DC applied is actually about 6μF. =3 μsec ⋅ 2.5V = 7.5μH A Configuration 0.6V Adjustable With External Feedback Fixed Output Output Voltage 1V, 1.2V 1.5V, 1.8V 2.5V, 3.3V 0.6V to 3.3V Inductor 2.2μH 4.7μH 6.8μH 4.7μH In this case, a standard 6.8μH value is selected. For high-voltage fixed versions (≥2.5V), m = 0.48A/ μsec. Table 1 displays inductor values for the AAT1146 fixed and adjustable options. Manufacturer's specifications list both the inductor DC current rating, which is a thermal limitation, and the peak current rating, which is determined by the saturation characteristics. The inductor should not show any appreciable saturation under normal load conditions. Some inductors may meet the peak and average current ratings yet result in excessive losses due to a high DCR. Always consider the losses associated with the DCR and its effect on the total converter efficiency when selecting an inductor. The 4.7μH CDRH3D16 series inductor selected from Sumida has a 105mΩ DCR and a 900mA DC current rating. At full load, the inductor DC loss is 17mW which gives a 2.8% loss in efficiency for a 400mA, 1.5V output. Table 1: Inductor Values. The maximum input capacitor RMS current is: IRMS = IO · VO ⎛ V⎞ · 1- O VIN ⎝ VIN ⎠ The input capacitor RMS ripple current varies with the input and output voltage and will always be less than or equal to half of the total DC load current. VO ⎛ V⎞ · 1- O = VIN ⎝ VIN ⎠ D · (1 - D) = 0.52 = 1 2 1146.2008.06.1.6 www.analogictech.com 11 PRODUCT DATASHEET AAT1146 SwitchRegTM for VIN = 2 · VO Fast Transient 400mA Step-Down Converter Output Capacitor I IRMS(MAX) = O 2 The output capacitor limits the output ripple and provides holdup during large load transitions. A 4.7μF to 10μF X5R or X7R ceramic capacitor typically provides sufficient bulk capacitance to stabilize the output during large load transitions and has the ESR and ESL characteristics necessary for low output ripple. The output voltage droop due to a load transient is dominated by the capacitance of the ceramic output capacitor. During a step increase in load current, the ceramic output capacitor alone supplies the load current until the loop responds. Within two or three switching cycles, the loop responds and the inductor current increases to match the load current demand. The relationship of the output voltage droop during the three switching cycles to the output capacitance can be estimated by: The term V ⎝ V ⎠ appears in both the input voltage ripple and input capacitor RMS current equations and is a maximum when VO is twice VIN. This is why the input voltage ripple and the input capacitor RMS current ripple are a maximum at 50% duty cycle. IN IN VO ⎛ V⎞ · 1- O The input capacitor provides a low impedance loop for the edges of pulsed current drawn by the AAT1146. Low ESR/ESL X7R and X5R ceramic capacitors are ideal for this function. To minimize stray inductance, the capacitor should be placed as closely as possible to the IC. This keeps the high frequency content of the input current localized, minimizing EMI and input voltage ripple. The proper placement of the input capacitor (C2) can be seen in the evaluation board layout in Figure 2. A laboratory test set-up typically consists of two long wires running from the bench power supply to the evaluation board input voltage pins. The inductance of these wires, along with the low-ESR ceramic input capacitor, can create a high Q network that may affect converter performance. This problem often becomes apparent in the form of excessive ringing in the output voltage during load transients. Errors in the loop phase and gain measurements can also result. Since the inductance of a short PCB trace feeding the input voltage is significantly lower than the power leads from the bench power supply, most applications do not exhibit this problem. In applications where the input power source lead inductance cannot be reduced to a level that does not affect the converter performance, a high ESR tantalum or aluminum electrolytic should be placed in parallel with the low ESR, ESL bypass ceramic. This dampens the high Q network and stabilizes the system. COUT = 3 · ΔILOAD VDROOP · FS Once the average inductor current increases to the DC load level, the output voltage recovers. The above equation establishes a limit on the minimum value for the output capacitor with respect to load transients. The internal voltage loop compensation also limits the minimum output capacitor value to 4.7μF. This is due to its effect on the loop crossover frequency (bandwidth), phase margin, and gain margin. Increased output capacitance will reduce the crossover frequency with greater phase margin. The maximum output capacitor RMS ripple current is given by: IRMS(MAX) = VOUT · (VIN(MAX) - VOUT) L · F · VIN(MAX) 2· 3 · 1 Dissipation due to the RMS current in the ceramic output capacitor ESR is typically minimal, resulting in less than a few degrees rise in hot-spot temperature. 12 www.analogictech.com 1146.2008.06.1.6 PRODUCT DATASHEET AAT1146 SwitchRegTM Fast Transient 400mA Step-Down Converter Figure 2: AAT1146 Evaluation Board Top Side Layout. Figure 3: Exploded View of Evaluation Board Top Side Layout. Figure 4: AAT1146 Evaluation Board Bottom Side Layout. Adjustable Output Resistor Selection For applications requiring an adjustable output voltage, the 0.6V version can be externally programmed. Resistors R1 and R2 of Figure 5 program the output to regulate at a voltage higher than 0.6V. To limit the bias current required for the external feedback resistor string while maintaining good noise immunity, the minimum suggested value for R2 is 59kΩ. Although a larger value will further reduce quiescent current, it will also increase the impedance of the feedback node, making it more sensitive to external noise and interference. Table 2 summarizes the resistor values for various output voltages with R2 set to either 59kΩ for good noise immunity or 221kΩ for reduced no load input current. ⎛ VOUT ⎞ ⎛ 1.5V ⎞ R1 = V -1 · R2 = 0.6V - 1 · 59kΩ = 88.5kΩ ⎝ REF ⎠ ⎝ ⎠ The adjustable version of the AAT1146, combined with an external feedforward capacitor (C4 in Figure 5), delivers enhanced transient response for extreme pulsed load applications. The addition of the feedforward capacitor typically requires a larger output capacitor C1 for stability. 1146.2008.06.1.6 www.analogictech.com 13 PRODUCT DATASHEET AAT1146 SwitchRegTM R2 = 59kΩ VOUT (V) 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.8 1.85 2.0 2.5 3.3 Fast Transient 400mA Step-Down Converter R2 = 221kΩ R1 75K 113K 150K 187K 221K 261K 301K 332K 442K 464K 523K 715K 1.00M R1 (kΩ) 19.6 29.4 39.2 49.9 59.0 68.1 78.7 88.7 118 124 137 187 267 switching devices. At full load, assuming continuous conduction mode (CCM), a simplified form of the losses is given by: PTOTAL = IO2 · (RDSON(HS) · VO + RDSON(LS) · [VIN - VO]) VIN + (tsw · F · IO + IQ) · VIN IQ is the step-down converter quiescent current. The term tsw is used to estimate the full load step-down converter switching losses. For the condition where the step-down converter is in dropout at 100% duty cycle, the total device dissipation reduces to: Table 2: Adjustable Resistor Values For Use With 0.6V Step-Down Converter. PTOTAL = IO2 · RDSON(HS) + IQ · VIN Since RDS(ON), quiescent current, and switching losses all vary with input voltage, the total losses should be investigated over the complete input voltage range. Given the total losses, the maximum junction temperature can be derived from the θJA for the SC70JW-8 package which is 160°C/W. Thermal Calculations There are three types of losses associated with the AAT1146 step-down converter: switching losses, conduction losses, and quiescent current losses. Conduction losses are associated with the RDS(ON) characteristics of the power output switching devices. Switching losses are dominated by the gate charge of the power output TJ(MAX) = PTOTAL · ΘJA + TAMB 1 2 3 Enable VIN C4 100pF 1 U1 AAT1146 R1 EN OUT VIN LX PGND PGND PGND AGND 8 7 6 5 2 3 4 VOUT =1.8V L1 118k 4.7μH C1 10μF C3 n/a R2 59k C2 4.7μF GND LX GND2 U1 AAT1146 SC70JW-8 L1 CDRH3D16-4R7 C2 4.7μF 10V 0805 X5R C1 10μF 6.3V 0805 X5R Figure 5: AAT1146 Adjustable Version Evaluation Board Schematic (for Fixed Version, R1 is a short and C4, R2 are open). 14 www.analogictech.com 1146.2008.06.1.6 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Layout The suggested PCB layout for the AAT1146 is shown in Figures 2, 3, and 4. The following guidelines should be used to help ensure a proper layout. 1. 2. The input capacitor (C2) should connect as closely as possible to VIN (Pin 3) and PGND (Pins 6-8). C1 and L1 should be connected as closely as possible. The connection of L1 to the LX pin should be as short as possible. The feedback trace or OUT pin (Pin 2) should be separate from any power trace and connect as closely as possible to the load point. Sensing along a high-current load trace will degrade DC load regulation. If external feedback resistors are used, they should be placed as closely as possible to the OUT pin (Pin 2) to minimize the length of the high impedance feedback trace. The resistance of the trace from the load return to the PGND (Pins 6-8) should be kept to a minimum. This will help to minimize any error in DC regulation due to differences in the potential of the internal signal ground and the power ground. Fast Transient 400mA Step-Down Converter A high density, small footprint layout can be achieved using an inexpensive, miniature, non-shielded, high DCR inductor. An evaluation board is available with this inductor and is shown in Figure 6. The total solution footprint area is 40mm2. 3. 4. Figure 6: Minimum Footprint Evaluation Board Using 2.0mm x 1.6mm x 0.95mm Inductor. 1146.2008.06.1.6 www.analogictech.com 15 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Fast Transient 400mA Step-Down Converter Step-Down Converter Design Example Specifications VO = 1.8V @ 400mA (adjustable using 0.6V version), Pulsed Load ΔILOAD = 300mA VIN = 2.7V to 4.2V (3.6V nominal) FS = 1.4MHz TAMB = 85°C 1.8V Output Inductor L1 = 3 μsec μsec ⋅ VO2 = 3 ⋅ 1.8V = 5.4μH (use 4.7μH; see Table 1) A A For Sumida inductor CDRH3D16, 4.7μH, DCR = 105mΩ. ΔIL1 = ⎛ VO V⎞ 1.8V 1.8V ⎞ ⎛ ⋅ 1- O = ⋅ ⎝1 = 156mA L1 ⋅ F ⎝ VIN ⎠ 4.7µH ⋅ 1.4MHz 4.2V ⎠ IPKL1 = IO + ΔIL1 = 0.4A + 0.068A = 0.468A 2 PL1 = IO2 ⋅ DCR = 0.4A2 ⋅ 105mΩ = 17mW 1.8V Output Capacitor VDROOP = 0.1V COUT = 3 · ΔILOAD 3 · 0.3A = = 6.4μF; use 10µF VDROOP · FS 0.1V · 1.4MHz (VO) · (VIN(MAX) - VO) 1 1.8V · (4.2V - 1.8V) · = 45mArms = 4.7μH · 1.4MHz · 4.2V L1 · F · VIN(MAX) 2· 3 2· 3 1 · IRMS = Pesr = esr · IRMS2 = 5mΩ · (45mA)2 = 10μW Input Capacitor Input Ripple VPP = 25mV CIN = ⎛ VPP ⎝ IO 1 1 = = 3.11μF; use 4.7μF ⎞ ⎛ 25mV ⎞ - 5mΩ · 4 · 1.4MHz - ESR · 4 · FS ⎠ ⎝ 0.4A ⎠ IRMS = IO = 0.2Arms 2 P = esr · IRMS2 = 5mΩ · (0.2A)2 = 0.2mW 16 www.analogictech.com 1146.2008.06.1.6 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM AAT1146 Losses PTOTAL = IO2 · (RDSON(HS) · VO + RDSON(LS) · [VIN -VO]) VIN Fast Transient 400mA Step-Down Converter + (tsw · F · IO + IQ) · VIN = 0.42 · (0.725Ω · 1.8V + 0.7Ω · [4.2V - 1.8V]) 4.2V + (5ns · 1.4MHz · 0.4A + 70μA) · 4.2V = 126mW TJ(MAX) = TAMB + ΘJA · PLOSS = 85°C + (160°C/W) · 126mW = 105.1°C 1146.2008.06.1.6 www.analogictech.com 17 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Adjustable Version (0.6V device) VOUT (V) 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.8 1.85 2.0 2.5 3.3 Fast Transient 400mA Step-Down Converter R2 = 59kΩ R1 (kΩ) 19.6 29.4 39.2 49.9 59.0 68.1 78.7 88.7 118 124 137 187 267 R2 = 221kΩ1 R1 (kΩ) 75.0 113 150 187 221 261 301 332 442 464 523 715 1000 L1 (μH) 1.5 1.5 1.5 1.5 1.5 2.2 4.7 4.7 4.7 4.7 6.8 6.8 6.8 Fixed Version VOUT (V) 0.6-3.3V R2, R4 Not Used R1 (kΩ) 0 L1 (μH) 1.5 - 6.8 Table 3: Evaluation Board Component Values. Max DC Current (A) 1.20 0.90 0.73 0.40 0.45 0.80 0.98 0.82 1.30 Manufacturer Sumida Sumida Sumida Murata Murata Coilcraft Coiltronics Coiltronics Coiltronics Part Number CDRH3D16-2R2 CDRH3D16-4R7 CDRH3D16-6R8 LQH2MCN4R7M02 LQH32CN4R7M23 LPO3310-472 SD3118-4R7 SD3118-6R8 SDRC10-4R7 Inductance (μH) 2.2 4.7 6.8 4.7 4.7 4.7 4.7 6.8 4.7 DCR (Ω) 0.072 0.105 0.170 0.80 0.20 0.27 0.122 0.175 0.122 Size (mm) LxWxH 3.8x3.8x1.8 3.8x3.8x1.8 3.8x3.8x1.8 2.0x1.6x0.95 2.5x3.2x2.0 3.2x3.2x1.0 3.1x3.1x1.85 3.1x3.1x1.85 5.7x4.4x1.0 Type Shielded Shielded Shielded Non-Shielded Non-Shielded 1mm Shielded Shielded 1mm Shielded Table 4: Typical Surface Mount Inductors. Manufacturer Murata Murata Murata Part Number GRM219R61A475KE19 GRM21BR60J106KE19 GRM21BR60J226ME39 Value 4.7μF 10μF 22μF Voltage 10V 6.3V 6.3V Temp. Co. X5R X5R X5R Case 0805 0805 0805 Table 5: Surface Mount Capacitors. 1. For reduced quiescent current, R2 and R4 = 221kΩ. 18 www.analogictech.com 1146.2008.06.1.6 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Ordering Information Output Voltage1 Adj ≥ 0.6 1.0 1.2 1.3 1.8 1.875 Adj ≥ 0.6 Fast Transient 400mA Step-Down Converter Package SC70JW-8 SC70JW-8 SC70JW-8 SC70JW-8 SC70JW-8 SC70JW-8 SOT23-5 Marking2 OXXYY 4SXYY 1JXYY 1KXYY 1CXYY QMXYY Part Number (Tape and Reel)3 AAT1146IJS-0.6-T1 AAT1146IJS-1.0-T1 AAT1146IJS-1.2-T1 AAT1146IJS-1.3-T1 AAT1146IJS-1.8-T1 AAT1146IJS-1.875-T1 AAT1146IGV-0.6-T1 All AnalogicTech products are offered in Pb-free packaging. The term “Pb-free” means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/about/quality.aspx. Package Information SC70JW-8 0.50 BSC 0.50 BSC 0.50 BSC 1.75 ± 0.10 0.225 ± 0.075 2.00 ± 0.20 2.20 ± 0.20 0.048REF 0.15 ± 0.05 0.85 ± 0.15 1.10 MAX 0.100 7° ± 3° 0.45 ± 0.10 2.10 ± 0.30 4° ± 4° All dimensions in millimeters. 1. Contact Sales for other voltage options. 2. XYY = assembly and date code. 3. Sample stock is typically held on part numbers listed in BOLD. 1146.2008.06.1.6 www.analogictech.com 0.05 ± 0.05 19 PRODUCT DATASHEET AAT1146 AAT1146 SwitchRegTM Fast Transient 400mA Step-Down Converter SOT23-5 2.85 ± 0.15 1.90 BSC 0.95 BSC 1.575 ± 0.125 1.10 ± 0.20 0.60 REF 2.80 ± 0.20 1.20 ± 0.25 0.15 ± 0.07 4° ± 4° GAUGE PLANE 10° ± 5° 0.40 ± 0.10 0.075 ± 0.075 0.60 REF 0.45 ± 0.15 0.10 BSC All dimensions in millimeters. Advanced Analogic Technologies, Inc. 3230 Scott Boulevard, Santa Clara, CA 95054 Phone (408) 737-4600 Fax (408) 737-4611 © Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Except as provided in AnalogicTech’s terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied warranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. 20 www.analogictech.com 1146.2008.06.1.6