AAT4901IJS-3-T1

PRODUCT DATASHEET AAT4901 FastSwitchTM General Description The AAT4901 FastSwitch™ is a member of AnalogicTech’s Application Specific Power MOSFET™ (ASPM™) product family. It is a full-bridge buffered power stage operating with an input voltage range of 2.0V to 5.5V. The device is designed to operate with a switching frequency of up to 2MHz, minimizing the cost and size of external components. The AAT4901 is protected from shoot-through current by integrated break-before-make circuitry. The drivers can be independently controlled and their propagation delay, from input to output, is typically between 8ns-19ns dependent upon logic option. Four options are offered providing a single input control, dual input control or as two independent half-bridges. Other features include low RDS(ON) and low quiescent current allowing for high efficiency performance. The AAT4901 is available in the space-saving, Pb-free 8-pin SC70JW package and is rated over the -40°C to +85°C temperature range. Buffered Power Full-Bridge Features • VIN Range: 2.0V–5.5V • RDS(ON): High-side 220mΩ Low-side 160mΩ • Break-Before-Make Shoot–Through Protection • 4 Options Single Control Input with Enable • Two Logic Versions Dual Control Input with Brake Function Dual Half-bridge • Low Quiescent Current: 10µA (max) DC 4mA (max) at 1MHz • -40°C to +85°C Temperature Range • SC70JW-8 Package Applications DC Motor Drive Door Locks Dual Low-Side MOSFET Gate Driver Fan Motors High Frequency DC/DC Converters High Speed Line Drive Proximity Detectors Typical Applications IN CIN OUTA AAT4901-1 ENA OUTB ENB GND 4901.2008.03.1.0 www.analogictech.com 1 PRODUCT DATASHEET AAT4901 AAT4901 FastSwitchTM Pin Descriptions Symbol Pin # 1 2 3 4 5 6 7 8 N/C N/C GND OUTB OUTA END -1, -2, -4 ENA IN ENB ENC -3 Buffered Power Full-Bridge Function Active high enable signal. Supply voltage input; input voltage range from 2.0V to 5.5V. Active high enable signal. 4901-1/-2/-4: No connection. 4901-3: Active high enable signal. Ground connection Output of half-bridge B. Connect to load. Output of half-bridge A. Connect to load. 4901-1/-2/-4: No connection. 4901-3: Active high enable signal. Pin Configuration SC70JW-8 (Top View) ENA IN ENB N/C 1 2 3 4 8 7 6 5 N/C OUTA OUTB GND ENA IN ENB ENC 1 2 3 4 8 7 6 5 END OUTA OUTB GND AAT4901-1/-2/-4 AAT4901-3 2 www.analogictech.com 4901.2008.03.1.0 PRODUCT DATASHEET AAT4901 AAT4901 FastSwitchTM Absolute Maximum Ratings1 Symbol VIN VEN VOUT IMAX IMAX(PK) TLEAD Buffered Power Full-Bridge Description IN to GND ENA, ENB, ENC, END to GND OUT to GND Maximum Continuous Switch Current Maximum Peak Current Maximum Soldering Temperature (at Leads) Value -0.3 to 6.0 -0.3 to VIN + 0.3 -0.3 to VIN + 0.3 0.7 3 300 Units V V V A A °C Thermal Information Symbol PD ΘJA TJ Description Maximum Power Dissipation (TA = 25°C) Thermal Resistance2 Operating Junction Temperature Range Value 440 225 -40 to 150 Units mW °C/W °C 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on a FR4 board. 4901.2008.03.1.0 www.analogictech.com 3 PRODUCT DATASHEET AAT4901 AAT4901 FastSwitchTM Electrical Characteristics1 VIN = 5V, TA = -40 to 85°C unless otherwise noted. Typical values are at TA=25°C. Symbol VIN IQAC Buffered Power Full-Bridge Description Operation Voltage AC Quiescent Current Conditions AAT4901-1 AAT4901-2 IN = 5V, ENB (D) = IN, ENA = 1MHz, IOUT = 0 AAT4901-3 AAT4901-4 AAT4901-1 AAT4901-2 IN = 5V, ENB (D) = IN, ENA (C) = GND, IOUT = 0 AAT4901-3 AAT4901-4 ENB (D) = ENA (C) = GND, IN = OUT = 5.5V ENB (D) = GND, IN = 5.5V, VOUT = 0, or OUT = IN VIN= 4.5V VIN= 3.0V VIN= 2.0V VIN= 4.5V VIN= 3.0V VIN= 2.0V Min 2.0 Typ 3.8 2.0 0.72 0.9 5.5 Max 5.5 4.0 Units V mA IQDC DC Quiescent Current 10.0 µA IQ(OFF) ISD(OFF) RDS(ON)H Off-Supply Current Off-Switch Current High Side MOSFET On-Resistance 1.0 0.03 220 250 340 160 180 240 0.2 · VIN 0.5 · VIN 0.15 · VIN 0.01 5.0 5.0 15 15 8 14 18 15 7 19 12 10 10 12 11 10 7 12 1 µA µA mΩ RDS(ON)L VONL VONH VHYS ISINK TBBM Low Side MOSFET On-Resistance ENA ENA ENA ENA (C), ENB (D) Input Low Voltage (C), ENB (D) Input High Voltage (C), ENB (D) Input Hysteresis (C), ENB (D) Input Leakage mΩ V V V µA ns ns ns Break-Before-Make Time ENA (C) , ENB (D) = 5.5V ENA (C) Rising ENA (C) Falling ENA (C) Rising AAT4901-1 AAT4901-2 AAT4901-3 AAT4901-4 AAT4901-1 AAT4901-2 AAT4901-3 AAT4901-4 AAT4901-1 AAT4901-2 AAT4901-3 AAT4901-4 AAT4901-1 AAT4901-2 AAT4901-3 AAT4901-4 1.0 TON-DLY ENA (C) to OUT Delay ENA (C) Falling ns ENA (C) = GND THIZ ENB to OUT HiZ Delay ENA (C) = IN ns ns 1. The AAT4901 is guaranteed to meet performance specifications over the –40°C to +85°C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 4 www.analogictech.com 4901.2008.03.1.0 PRODUCT DATASHEET AAT4901 AAT4901 FastSwitchTM Typical Characteristics AC Quiescent Current vs. Input Voltage (ENB = IN; ENA = 1MHz; IOUT = 0; TA = 25°C) AC Quiescent Current (mA) AC Quiescent Current (mA) 1.5 4 3.5 3 2.5 2 1.5 1 2 2.5 3 3.5 4 4.5 5 5.5 Buffered Power Full-Bridge AC Quiescent Current vs. Input Voltage (ENA = ENB = 1MHz; IOUT = 0; TA = 25°C) 1.2 0.9 0.6 0.3 0 2 2.5 3 3.5 4 4.5 5 5.5 Input Voltage (V) Input Voltage (V) AC Quiescent Current vs. Switching Frequency (ENB = IN; ENA = 0.1kHz~2000kHz; IOUT = 0, TA = 25°C) AC Quiescent Current (mA) 10 AC Quiescent Current vs. Switching Frequency (ENA = ENB = 0.1kHz~2000kHz; IOUT = 0, TA = 25°C) AC Quiescent Current (mA) 10 1 1 0.1 0.1 0.01 0.01 VIN = 5.0V VIN = 3.0V 0.001 0.1 1 10 100 1000 10000 VIN = 5.0V VIN = 3.0V 0.001 0.1 1 10 100 1000 10000 Switching Frequency (kHz) Switching Frequency (kHz) AC Quiescent Current vs. Temperature (ENA = ENB = 1MHz; IOUT = 0) AC Quiescent Current (mA) DC Quiescent Current (µA) 4 8 7 6 5 4 3 2 1 0 -40 DC Quiescent Current vs. Temperature (ENB = IN; ENA = GND; IOUT = 0) 3 2 1 VIN = 5.0V VIN = 3.0V 0 -40 -15 10 35 60 85 VIN = 5.0V VIN = 3.0V -15 10 35 60 85 Temperature (°C) Temperature (°C) 4901.2008.03.1.0 www.analogictech.com 5 PRODUCT DATASHEET AAT4901 AAT4901 FastSwitchTM Typical Characteristics Low Side RDS(ON) vs. Output Current (TA = 25°C) 300 250 200 150 100 50 0 0.1 0.2 0.3 0.4 0.5 350 300 Buffered Power Full-Bridge High Side RDS(ON) vs. Output Current (TA = 25°C) RDS(ON)H (mΩ) RDS(ON)L (mΩ) 250 200 150 100 50 0 0.1 VIN = 2.0V VIN = 3.0V VIN = 4.5V 0.6 0.7 VIN = 2.0V VIN = 3.0V VIN = 4.5V 0.2 0.3 0.4 0.5 0.6 0.7 Output Current (A) Output Current (A) Low Side RDS(ON) vs. Temperature (IOUT = 0.7A) 350 300 400 350 High Side RDS(ON) vs. Temperature (IOUT = 0.7A) RDS(ON)H (mΩ) RDS(ON)L (mΩ) 250 200 150 100 50 0 -40 300 250 200 150 100 50 0 -40 VIN = 2.0V VIN = 3.0V VIN = 4.5V -15 10 35 60 85 VIN = 2.0V VIN = 3.0V VIN = 4.5V -15 10 35 60 85 Temperature (°C) Temperature (°C) MOSFETs RDS(ON) vs. Input Voltage (IOUT = 0.7A; TA = 25°C) 350 300 2.4 ENA/ENB Threshold vs. Input Voltage (TA = 25°C) ENA/ENB Threshold (V) 2 RDS(ON) (mΩ) 250 200 150 100 50 0 2 2.5 3 3.5 4 4.5 5 5.5 1.6 1.2 High Side Low Side 0.8 VON_H VON_L 2 2.5 3 3.5 4 4.5 5 5.5 0.4 Input Voltage (V) Input Voltage (V) 6 www.analogictech.com 4901.2008.03.1.0 PRODUCT DATASHEET AAT4901 AAT4901 FastSwitchTM Functional Block Diagram IN Buffered Power Full-Bridge OUTA OUTB ENA Control Logic ENB GND ENC END AAT4901-3 Only Functional Description The AAT4901 is a buffered full-bridge driver IC with options to allow the device to function as two independent half-bridges. The output stage is capable of driving output loads of up to 0.7A and features break-before-make timing and very fast propagation delay time, allowing high switching speed up to 2MHz. The enable input (EN), when driven low, turns off the driver and reduces the operating current to less than 1μA. Logic options allow the AAT4901 to be used as a small DC motor driver with break function, a solenoid driver, a dual-low-side MOSFET driver, or as a coil driver. Applications include motor drive, proximity detectors, electronic locks, and DC-DC converters. 4901.2008.03.1.0 www.analogictech.com 7 PRODUCT DATASHEET AAT4901 FastSwitchTM Options AAT4901-1 H-bridge configuration with two enables. Enable B is active high and enables the H-bridge output. Enable A toggles the H-bridge outputs A and B in anti-phase. In steady state, this can provide forward/reverse motor drive signals. ENA 0 1 0 1 Buffered Power Full-Bridge AAT4901-1/-4 Logic Table -1 ENB 0 0 1 1 -4 ENA 0 1 1 0 ENB 0 1 0 1 OUTA Hi Z Hi Z IN GND OUTB Hi Z Hi Z GND IN AAT4901-2 H-bridge configuration with two enables. Enable A and Enable B are in anti-phase and provide forward/reverse and braking. AAT4901-2 Logic Table ENA 0 1 0 1 ENB 0 0 1 1 OUTA Hi Z IN GND IN OUTB Hi Z GND IN IN AAT4901-3 Dual independent half-bridge configuration with four enables. Function similar to 2 x AAT4900. AAT4901-4 H-bridge with two enables. Enable A and Enable B are in anti-phase and toggle the H-bridge outputs A and B in anti-phase respectively. In steady state, this can provide forward/reverse motor drive signals to adjust the motor speed by various duty cycles. AAT4901-3 Logic Table ENA/C 0 1 0 1 ENB/D 0 0 1 1 OUTA/B Hi Z Hi Z IN GND Timing Diagram TON-DLY-F V_ENA 50% 50% 50% 50% T ON-DLY-R 90% (OFF) (OFF) V_OUTA 10% Hi Z Hi Z TON-DLY-R TON-DLY-F V_ENB 50% 50% 50% 50% 90% (OFF) 10% (OFF) V_OUTB Hi Z Hi Z TON-DLY-F TON-DLY-R THIZ_GND THIZ_IN Figure 1: AAT4901-4 Timing Diagram. 8 www.analogictech.com 4901.2008.03.1.0 PRODUCT DATASHEET AAT4901 FastSwitchTM Application Information Input Supply Capacitor The input capacitor provides a low impedance loop for the edges of pulsed current drawn by the AAT4901 and reduces the surge current drawn from the input power. A 4.7μF to 10μF X7R or X5R low ESR/ESL ceramic capacitor is selected for the input supply decoupling. To minimize the tray resistance, the capacitor should be placed as closely as possible to the input pin. This keeps the high frequency content of input current localized, minimizing EMI and input voltage ripple. Where: TJ(MAX) = junction temperature of the dice (°C). TA = ambient temperature (°C). θJA = thermal resistance (225°C/W). IQAC = AC quiescent current of the driver (mA). QG(tot) = total gate charge of external low side MOSFETs (nC). FSW = switching frequency (MHz). The maximum junction temperature for the SC70JW-8 package can be derived from Equation 1: Eq. 2: TJ(MAX) = PD(MAX) · θJA + TA For example, if the AAT4901 drives 2 AAT9560 MOSFETs whose maximum gate charge is specified as 13nC for VGATE = 5V, the total power dissipation in the driver at a switching frequency of 1MHz equals: Buffered Power Full-Bridge Shoot-Through Protection The internal high-side and low-side MOSFETs of the AAT4901 cannot conduct at the same time to prevent shoot-through current. When the high-side MOSFET turns on, the low-side MOSFET turns off first; after 5ns break-before-make time, the high-side MOSFET then turns on. Similarly, before the low-side MOSFET turns on, the high-side MOSFET turns off; after a certain break-before-make time (5ns typ.), the low-side MOSFET turns on. The dead time between the high-side and lowside turn-on should be kept as low as possible to minimize current flows through the body diode of the highside and/or low-side MOSFET(s). The break-before-make shoot-through protection significantly reduces losses associated with the driver at high frequency. PD(tot) = 2 · (5V · 13nC · 1MHz) + 5V · 4.0mA = 150mW Gate Drive Current Ratings Assuming that the maximum gate charge of the dual low-side MOSFETs are equal, the maximum gate drive capability for the designed maximum junction temperature without an external resistor can be derived from Equation 1: Eq. 3: QG(MAX) = Thermal Calculations In the dual low-side MOSFET driver application, the power dissipation of the AAT4901 includes the power dissipation in the MOSFETs due to charging and discharging the gate capacitance, the AC quiescent current power dissipation, and transient power in the driver during output transitions. As the transient power is usually very small, its losses can be ignored. Maximum package power dissipation can be estimated by the following equation: Eq. 1: PD(MAX) = VCC · IIN = 1 · 2 · FSW TJ(MAX) - TA - IQAC θJA · VIN The relationship between gate capacitance, turn-on/ turn-off time, and the MOSFET driver current rating can be determined by: Eq. 4: IG(MAX) = CG(MAX) · Where: IG(MAX) = peak drive current for a given voltage CG(MAX) = maximum gate capacitance dV = MOSFET gate-to-source voltage dt = rising time of MOSFET gate-to-source voltage dV dt TJ(MAX) - TA θJA = IQAC · VCC + QG(tot)FSW · VCC 4901.2008.03.1.0 www.analogictech.com 9 PRODUCT DATASHEET AAT4901 FastSwitchTM The relationship between CG(MAX) , QG(MAX) , and VGATE is given by: Eq. 5: CG(MAX) = Buffered Power Full-Bridge Typical Applications 2-Phase Synchronous Buck Converter The most common AAT4901 applications include multiphase DC/DC converter output power stages, DC motor drive, a dual low-side MOSFET driver, and a 3-state highspeed high-current line driver. Figure 2 shows a typical configuration when used as a 2-phase buck converter power stage with synchronous rectification. The EN pin can be used to force outputs OUTA/OUTB to a high impedance state; this allows the output inductor to operate in discontinuous condition mode (DCM) and improves efficiency under light load conditions. The body diode associated with the low-side switching device gives the AAT4901 inductive switching capability, and clamps the LX node at one diode drop below GND during the break-before-make time. The multiphase buck converter assures a stable, high-performance topology for high currents and low voltages which are demanded in computers, workstation, telecom and datacom servers. Figure 3 illustrates output ripple current reduction due to 2-phase cancellation. QG(MAX) VGATE The peak current drive requirements for a given MOSFET gate voltage can be derived from Equations 4 and 5: Eq. 6: IG(MAX) = QG(MAX) dt Design Example VIN = 5V VGATE = 5V FSW = 1MHz θJA = 225°C/W IQAC = 4.0mA TJ(MAX) = 120°C TA = 85°C tRISE = dt = 10ns QG(MAX) = 1 ⎛ 120°C - 85°C ⎞ · - 4.0mA = 13.6nC ⎠ 2 · 1MHz ⎝ 225°C/W · 5V CG(MAX) = QG(MAX) 13.6nC = = 2.7nF VGATE 5V QG(MAX) 13.6nC = = 1.36A dt 10ns Motor Drive The AAT4901 is ideally suited for use as an efficient output driver for DC brushless motor control due to its full bridge output stage with integrated MOSFETs. The inductive load switching capability of the AAT4901 eliminates the need for external diodes during commutation time. In applications where rotation is always in the same direction, a single half-bridge AAT4900 can be used to drive a DC motor. If needed to control the rotation in both directions, full-bridge motor control circuits can be applied as shown in Figure 4. In this configuration the motor can be controlled to run clockwise, counter-clockwise, stop rapidly (“regeneration” braking) or free run (coast) to a stop. IG(MAX) = 10 www.analogictech.com 4901.2008.03.1.0 PRODUCT DATASHEET AAT4901 FastSwitchTM On/Off (EN) VIN: 2.0V ~ 5.5V Buffered Power Full-Bridge VCC PWM1 2 -Phase DC/DC Controller PWM2 SW2 SW1 1 ENA IN AAT4901-3 ENB ENC END OUTA OUTB GND 8 2 7 IL1 IL2 L1 IL1 + IL2 VOUT CIN GND FB 3 6 L2 R1 CO 4 5 R2 Figure 2: AAT4901 in 2-Phase Synchronous Buck Converter Power Stage. OUTA OUTB IL2 IL1 IL1+IL2 Figure 3: Output Current Ripple Reduction (IL1+IL2) due to 2-Phase Cancellation. When the voltage applied between the DC motor by the input(s) logic control is reversed, it could change the rotation direction. When both outputs (OUTA/OUTB) are floating, the motor winding acts as a regeneration; the current inside the motor winding would continue to flow into the input capacitor through the internal MOSFET parasitic diode and decay to zero rapidly, stopping the motor rapidly. When both outputs are connected to the input supply (or ground) simultaneously, the motor coasts and the winding current decays slowly due to the winding resistor until the motor free runs to a stop. The speed of a DC motor is directly proportional to the supply voltage. It can be controlled by simply adjusting the voltage sent to the motor, but this is quite inefficient. A better method is to switch the motor’s supply on and off rapidly. If the switching is fast enough, the motor doesn’t notice it, it only notices the average effect. The time it takes a motor to speed up and slow down under switching conditions is dependent on the inertia of the rotor (basically how heavy it is) and the amount of friction and load torque. Figure 5 shows the speed of a motor that is being turned on and off at a fairly low switching frequency. The average speed is around 150, although it varies quite a bit. If the supply voltage is switched quickly enough, the motor will not have time to change speed much and the speed will be quite steady. When the duty cycle (D = TON/T) is increased, the average speed of the motor increases. Thus the speed is controlled by the duty cycle of the PWM (Pulse Width Modulation). 4901.2008.03.1.0 www.analogictech.com 11 PRODUCT DATASHEET AAT4901 FastSwitchTM VIN: 2.0~5.5V VIN: 2.0~5.5V Buffered Power Full-Bridge CLK/DIR 1 8 ENA 2 N/C OUTA AAT4901-1 OUTB GND 7 6 5 CLK/DIR Brake 1 2 ENA IN AAT4901-2 ENB N/C N/C OUTA OUTB GND 8 7 6 5 IN ENB N/C M CLK/DIR Brake EN M 3 4 3 4 C1 4.7µF/16V C1 4.7µF/16V VIN: 2.0~5.5V EN CLK/DIR 1 8 VIN: 2.0~5.5V ENA 2 END 7 CLK/DIR 1 2 3 ENA IN AAT4901-4 ENB N/C N/C OUTA OUTB GND 8 7 6 5 IN 3 OUTA AAT4901-3 6 M 5 M ENB 4 OUTB GND C1 4.7µF/16V ENC 4 C1 4.7µF/16V Figure 4: Full-Bridge Motor Driver Using AAT4901. 200 20 Motor Speed 15 Supply Voltage 150 Motor Speed 100 10 Supply Voltage 50 5 0 Ton T Time 0 Figure 5: Motor Speed vs. Supply Voltage. 12 www.analogictech.com 4901.2008.03.1.0 PRODUCT DATASHEET AAT4901 FastSwitchTM The minimum switching frequency is chosen based on motor characteristics (the equivalent inductance and the parasitic series resistor) and the percentage of current variation to the average current specified. The minimum switching frequency is in direct proportion to the parasitic series resister, and in inverse proportion to the equivalent inductance and allowable current ripple. When driving a high-voltage DC motor, external highvoltage MOSFETs are needed to commutate the motor. In this application, the AAT4901 can be configured as a double-ended gate driver, as illustrated in Figure 6. The full-bridge power stage operates the motor drive control as shown in Figure 7. Each side of the motor can be connected either to the battery's positive terminal or to the battery's negative terminal through the switch. Note that only one MOSFET on each side of the motor may be turned on at any one time; otherwise the high-side and low-side MOSFETs will short out the battery and burn out. Buffered Power Full-Bridge There is also a diode connected in reverse across the field winding, to absorb the current in the field winding when all four MOSFETs in the bridge are turned off. During period (A), to make the motor run forwards, Q4 is turned on, and Q1 has the PWM signal applied to it. The current path is shown in blue in Figure 7. At period (B) Q4 is kept on, so when the Q1 PWM signal is off, current can continue to flow around the bottom loop through Q3’s parasitic diode. At period (C), to make the motor run backwards or control the speed, Q3 is turned on, and Q2 has the PWM signal applied to it. At period (D), Q3 is kept on, so when the Q2 PWM signal is off, current can continue to flow around the bottom loop through Q4’s parasitic diode. At period (E), when the motor is running forwards for example, the motor is now acting as a generator and forcing current through its armature, through Q2’s diode, through the battery (thereby charging the battery) and back through Q3’s diode. High-Voltage Rail VIN: 5.0V CLK1 1 ENA IN N/C(END) 8 2 CLK2 3 OUTA AAT4901-1,-2,-4 (-3) ENB OUTB N/C(ENC) GND 7 to Motor 6 4 5 C1 4.7µF/16V Figure 6: Double-Ended Gate Driver. 4901.2008.03.1.0 www.analogictech.com 13 PRODUCT DATASHEET AAT4901 FastSwitchTM VBAT + Lf Field winding Q1 La Ia Q2 Buffered Power Full-Bridge VBAT + Lf Field winding Q1 La Ia Q2 Q3 armature Q4 Q3 armature Q4 VBAT Period (A) VBAT Period (B) VBAT + Lf Field winding Q1 La Ia Q2 VBAT + Lf Field winding Q1 La Ia Q2 Q3 armature Q4 Q3 armature Q4 VBAT Period (C) VBAT Period (D) VBAT + Lf Field winding Q1 La Ia Q2 Q3 armature Q4 VBAT Period (E) Figure 7: Full-Bridge Motor Drive Control. Dual Channel, High Speed, High Current 3-State Line Driver The AAT4901-3 is ideally suited for dual channel, high speed, high current 3-state line driver applications such as CCD clock drivers. The low quiescent power dissipation makes this part attractive in battery powered products. The 3A peak drive capability also makes the AAT4901-3 an excellent choice for driving high speed capacitive lines. The 20ns fast switching/delay time allows clocking speeds up to 10MHz. Dual Low-Side MOSFET Driver The AAT4901-3 is also ideally suited for dual low-side MOSFET driver applications due to its dual independent half-bridge output configuration. It can be used in a push-pull topology as illustrated in Figure 9 or in other applications which require the ability to drive the MOSFETs quickly, due to the AAT4901's extremely low RDS(ON) (220/160mΩ typ.) and very fast propagation time (20ns typ.) 14 www.analogictech.com 4901.2008.03.1.0 PRODUCT DATASHEET AAT4901 AAT4901 FastSwitchTM ENA Buffered Power Full-Bridge IN 3-State ENB OUTA ENC OUTB 3-State END GND Figure 8: AAT4901-3 Dual Channel High-Speed High-Current 3-State Line Driver. VOUT VIN + + VCC: 5.0V EN PWM A 1 8 ENA IN AAT4901-3 ENB ENC END OUTA OUTB GND 2 7 3 6 PWM B 4 5 C1 4.7µF/16V Figure 9: Push-Pull Topology MOSFET Driver with AAT4901. 4901.2008.03.1.0 www.analogictech.com 15 PRODUCT DATASHEET AAT4901 AAT4901 FastSwitchTM Ordering Information Package SC70JW-8 SC70JW-8 SC70JW-8 SC70JW-8 Buffered Power Full-Bridge Marking1 XXGYY XXGYY XXGYY 2SGYY Part Number (Tape and Reel)2 AAT4901IJS-1-T1 AAT4901IJS-2-T1 AAT4901IJS-3-T1 AAT4901IJS-4-T1 All AnalogicTech products are offered in Pb-free packaging. The term “Pb-free” means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/about/quality.aspx. Package Information SC70JW-8 0.50 BSC 0.50 BSC 0.50 BSC 1.75 ± 0.10 0.225 ± 0.075 2.00 ± 0.20 2.20 ± 0.20 0.048REF 0.85 ± 0.15 0.15 ± 0.05 1.10 MAX 0.100 7 ° ± 3° 0.45 ± 0.10 2.10 ± 0.30 4° ± 4° All measurements in millimeters. 1. XXGYY: XX denotes Device code, G denotes assembly code, and YY denotes date code. 2. Sample stock is generally held on part numbers listed in BOLD. Advanced Analogic Technologies, Inc. 3230 Scott Boulevard, Santa Clara, CA 95054 Phone (408) 737-4600 Fax (408) 737-4611 © Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Except as provided in AnalogicTech’s terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied warranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. 16 www.analogictech.com 0.05 ± 0.05 4901.2008.03.1.0